Search

Abstract Bitumen shows visco-elastic behavior, exhibiting both elastic and viscous properties as predicted by dynamic response and phase angle. Modern asphalt bituminous pavements face issues such as early-stage fatigue cracks, rutting, and permanent deformations due to low-temperature cracking, high-temperature deformation, moisture susceptibility, and overloading. These pavement distresses result in the formation of potholes, alligator cracks, and various deformations, which accelerate the need for rehabilitation and maintenance. To address these concerns, this study focused on utilizing Nitrile Butadiene Rubber derived from surgical gloves as an additive in conventional asphalt pavements to assess its effect on stiffness. Nitrile Butadiene Rubber was added in intervals of 2%, 4%, 6%, and 8% to conventional bituminous pavement. The rheological properties, marshall properties, dynamic modulus, and phase angle were evaluated for varying percentages of Nitrile Butadiene Rubber at different temperature, and frequency. The dynamic response was determined using a simple performance tester at four different temperatures (4.4 °C, 21.1 °C, 37.8 °C, and 54.4 °C) and six different frequencies (0.1, 0.5, 1, 5, 10, and 25 Hz). Response surface methodology was employed to establish a relationship between input and output variables and to optimize the amount of Nitrile Butadiene Rubber in the mix based on dynamic modulus and phase angle. The study concluded that adding up to 6% of Nitrile Butadiene Rubber improved Marshall stability, while higher percentages led to reduced stability. A similar trend was observed in the dynamic modulus, which peaked with the addition of 6% Nitrile Butadiene Rubber, regardless of frequency and temperature. The response surface methodology model indicated that coupling the percentage of Nitrile Butadiene Rubber with frequency increased the dynamic modulus at a constant temperature, with the highest value occurring at 4.4 °C. However, the dynamic modulus decreased as the temperature rose for the same combinations of Nitrile Butadiene Rubber percentages and frequencies. Numerical optimization suggested that a maximum of 5.9% Nitrile Butadiene Rubber should be added to achieve the highest dynamic modulus and lowest phase angle.

Abstract Humans are the only species who generate waste materials that cannot be broken down by natural processes. The ideal solution to this waste problem would be to employ only compostable materials. Biodegradable materials play a key role in creating a safer and greener world. Biodegradability is the gift that keeps on giving, in the sense of creating an Earth worth living. The future is thus best served by green energy, sustainability, and renewable resources. To realize such goals, waste should be considered as a valuable resource. In this context, Zea mays (Zm) root fibres, which are normally considered as agricultural waste, can be used as reinforcing substances in polymer matrices to produce structural composite materials. Before being used in composites, such fibres must be analysed for their physical properties. Chemical treatments can be employed to improve the structural quality of fibres, and the changes due to such modification can be analysed. Therefore, the current work examines the effect of permanganate treatment on the surface properties of Zm fibres. The raw and potassium permanganate-treated samples were assayed for various properties. Physical analysis of the fibre samples yielded details concerning the physical aspects of the fibres. The thermal conductivity and moisture absorption behaviour of the samples were analysed. Chemical analysis was employed to characterize the composition of both treated and untreated samples. p-XRD was employed to examine the crystalline nature of the Zm fibres. Numerous functional groups present in each sample were analysed by FTIR. Thermogravimetric analysis was used to determine the thermal stability of Zm fibres. Elemental analysis (CHNS and EDS) was used to determine the elemental concentrations of both raw and treated samples. The surface alterations of Zm fibres brought on by treatment were described using SEM analysis. The characteristics of Zm roots and the changes in quality due to treatment were reviewed, and there were noticeable effects due to the treatment. Both samples would have applications in various fields, and each could be used as a potential reinforcing material in the production of efficient bio-composites.

Vehicles are frequently impacted objects during floods, susceptible to being washed away when the flow velocity and water depth surpass specific thresholds. Thus, understanding the characteristics of vehicle instability in floodwaters is crucial for establishing effective safety guidelines. This paper presents a comprehensive review, delving into previous studies on flooded vehicle stability during flood events and assessing progress in guideline formulation spanning from 2010 to 2023. According to the literature, 78 % of the previous investigations focused on the stability of static vehicles, while only 22 % considered vehicles in motion. Previous studies on vehicle stability during tsunamis have not been well-explored. Moreover, emergency vehicles, including police cars, fire trucks, and ambulances, received little attention and were only considered in two studies. On the other hand, extensive research has been conducted on defining the critical vehicle orientation with respect to incoming flow, which is reported to occur when the flow direction is perpendicular to the longitudinal vehicle axis. However, it is expected that this review will serve as a foundational resource, inspiring researchers to identify areas requiring attention and delve deeper into producing general safety guidelines. The ultimate goal is to prevent fatalities related to flooded vehicles and contribute to the broader field of flood risk mitigation.

Abstract Recent and past studies mainly focus on reducing the dead weight of structure; therefore, they considered lightweight aggregate concrete (LWAC) which reduces the dead weight but also affects the strength parameters. Therefore, the current study aims to use varied steel wire meshes to investigate the effects of LWAC on mechanical properties. Three types of steel wire mesh are used such as hexagonal (chicken), welded square, and expanded metal mesh, in various layers and orientations in LWAC. Numerous mechanical characteristics were examined, including energy absorption (EA), compressive strength (CS), and flexural strength (FS). A total of ninety prisms and thirty-three cubes were made. For the FS test, forty-five 100 × 100 × 500 mm prism samples were poured, thirty-three 150 × 150 × 150 mm cube samples were made, and forty-five 400 × 300 × 75 mm EA specimens were costed for fourteen days of curing. The experimental findings demonstrate that the FS was enhanced by adding additional forces that spread the forces over the section. One layer of chicken, welded, and expanded metal mesh enhances the FS by 52.96%, 23.76%, and 22.2%, respectively. In comparison to the remaining layers, the FS in a single-layer hexagonal wire mesh has the maximum strength, 29.49 MPa. The hexagonal wire mesh with a single layer had the greatest CS, measuring 36.56 MPa. When all three types of meshes are combined, the CS does not vary in this way and is estimated to be 29.79 MPa. In the combination of three layers, the chicken and expanded wire mesh had the most energy recorded prior to final failure, which was 1425.6 and 1108.7 J, whereas it was found the highest 752.3 J for welded square wire mesh. The energy absorption for the first layer with hexagonal wire mesh increased by 82.81% prior to the crack and by 88.34% prior to the ultimate failure. Overall, it was determined and suggested that hexagonal wire mesh works better than expanded and welded wire meshes.

Preserving the unique ecosystems of specific coastal areas is crucial for environmental health and the welfare of local communities. This study explores the rich biodiversity of flora and fauna along the Kedah state coastline, a 440 km stretch along the Strait of Malacca. Through meticulous site surveys and comprehensive data collection across multiple locations, followed by laboratory analyses, this research reveals a vibrant tapestry of life. The Kedah coastal area boasts a remarkable diversity, with 60 fish species identified, predominantly from the Carangidae (12 %) and Mugilidae (10 %) families. Additionally, five marine mammal species were documented, though turtles and terrapins were notably absent. The condition of coral reefs varied, with ''fair'' conditions observed at stations St-1 and St-2 (31.67 % and 35.67 % live coral, respectively), and ''poor'' conditions at St-3 (10.67 % live coral). High densities of phytoplankton, zooplankton, macrobenthos, and seaweed were recorded, whereas seagrass vegetation was absent. The study on Kedah’s coastal flora and fauna revealed a diverse range of species, including fish, marine mammals, corals, phytoplankton, zooplankton, macrobenthos, and seaweed. Coral reefs were found to be in varying conditions, with some needing restoration. The study recommends long-term monitoring, seasonal surveys, and focused research on key species. Habitat protection, community awareness, and sustainable practices are also emphasized to preserve the ecological balance of these marine environments. Moreover, the findings of this study provide a critical understanding of the Kedah coastal ecosystem and offer valuable insights for local authorities to develop effective conservation strategies. This research underscores the importance of preserving biodiversity to maintain ecological balance and support sustainable development in coastal regions.

Lightweight fibre-reinforced concrete integrates the advantages of lightweight aggregates with the strength-enhancing properties of fibres, resulting in a lighter composite with enhanced impact and mechanical performance. However, achieving an optimal balance between structural weight, and performance remains a challenging endeavour. This study investigates the mechanical properties, impact energy absorptions, flexural toughness, and crack resistance of lightweight fibre-reinforced concrete with the coarse aggregate entirely replaced with lightweight expanded clay aggregate (LECA). Concrete mixes containing 0 %, 0.5 %, 0.75 %, and 1.0 % Polypropylene fibre (PPF) and 10 % micro-silica were experimentally investigated. Predictions for concrete mixes with up to 2 % PPF were made using regression models developed from experimental data. The experimental and predicted results were analysed using response surface methodology. The findings reveal significant enhancements of up to 300 % and 570 % in toughness indices I5 and I10 at 1 % PPF, coupled with a 55.4 % increase in residual strength. Furthermore, an optimised slab thickness of 47 mm containing 1.73 % PPF yielded optimal impact energy absorption of 680 J and 2384 J and crack resistance of 3823 MPa and 16279 MPa at service and ultimate loading, respectively. These metrics represent improvements of 4.8, 15.2, 37, and 56 times, respectively, compared to the control samples. These substantial advancements highlight the potential of lightweight fibre-reinforced LECA concrete in engineering applications where balancing impact energy absorption, crack resistance, and structural weight is crucial. This innovative approach promises a transformative impact on the construction industry, paving the way for more efficient and resilient infrastructure.

This study assesses the integration of circular economy principles in concrete technology to mitigate the environmental impacts of traditional concrete production and promote sustainable construction practices. Using a comprehensive literature review, the research examines the utilization of various industrial waste materials—such as fly ash, coal bottom ash, palm oil fuel ash, sugarcane bagasse ash, and ground granulated blast furnace slag—as supplementary cementitious materials. The analysis focuses on their properties, environmental benefits, and potential to enhance concrete sustainability. The findings reveal that these industrial wastes can significantly reduce the carbon footprint of concrete production while improving mechanical properties and durability. The materials demonstrate notable pozzolanic characteristics and contribute to enhanced resilience in concrete structures. The study underscores the critical role of circular economy practices in transforming the construction sector, advocating for the adoption of waste-derived SCMs to foster environmental stewardship and sustainable development in the industry.

This review systematically examines the multitude of factors influencing bonding strength in bamboo-based composite materials, given the rising prominence of bamboo as a green building material. With bamboo's inherent variability in mechanical properties and structure, engineered bamboo products have emerged to address challenges related to connections and joints. Such advancements have necessitated a detailed exploration of adhesive systems, a significant cost determinant in bamboo production. The adhesive bonding mechanism in bamboo, akin to wood, involves intricate processes including adhesive spreading, penetration, and solidification, influenced by the unique chemical composition of bamboo. The interfacial bond quality plays a pivotal role in determining the durability and performance of the final products, with numerous factors such as bamboo species, layered structure, adhesive type, and treatment types impacting the mechanical properties. Particular attention is given to the disparities in physical and mechanical properties between the bamboo culm's core and shell layers, attributing complexities to the gluing process. Examining shear failure strength reveals its criticality in mechanical investigations, with variations in bonding strength affecting the outcome. The review underscores the need for consistent quality control and adept manipulation of these influential factors for the successful manufacture of bamboo-based products. A comprehensive discussion ensues on the variables controlling the bonding properties of the developed bamboo products, aiming to evaluate and highlight the optimal parameters and procedures essential for enhancing the quality and reliability of bamboo-based composite materials for sustainable construction applications.

Abstract This paper investigates the hemp limecrete mechanical and microstructural performance of a new sustainable and environmental friendly building material. Several studies have investigated the hemp limecrete focusing on the non-structural applications. The newly developed hemp limecrete consists of high mechanical and microstructural properties. The specimens were prepared with varying lengths and proportions of hemp fibers with lime and tested for compressive strength, flexural strength, thermal conductivity and microstructural analysis like SEM and EDS. The study found that the optimal fiber content for making mortars was between 2 and 4%. This conclusion was reached after analyzing the influence of fiber length and ratio on the properties of the mortars. The dry unit weight decreased when the fiber content was higher than 4%. In terms of strength, the study found that the flexural strength of the hemp limecrete improved with an increase in fiber ratio, but the compressive strength decreased. However, with 2% hemp fiber, compressive strengths of 3.48 MPa and above were obtained. The study also highlighted the good thermal insulation properties and dimensional stability of hemp limecrete. These findings have important implications for the use of hemp limecrete as a sustainable building material. The results suggest that hemp limecrete has the potential to be a viable alternative to conventional concrete in specific applications, particularly in areas where environmental sustainability is a priority.

Abstract Natural fiber is a viable and possible option when looking for a material with high specific strength and high specific modulus that is lightweight, affordable, biodegradable, recyclable, and eco-friendly to reinforce polymer composites. There are many methods in which natural fibres can be incorporated into composite materials. The purpose of this research was to evaluate the physico-chemical, structural, thermal, and mechanical properties of Acacia pennata fibres (APFs). Scanning electron microscopy was used to determine the AP fibers' diameter and surface shape. The crystallinity index (64.47%) was discovered by XRD. The irregular arrangement and rough surface are seen in SEM photos. The findings demonstrated that fiber has high levels of cellulose (55.4%), hemicellulose (13.3%), and low levels of lignin (17.75%), which were determined through chemical analysis and validated by Fourier Transform Infrared Spectroscopy (FTIR). By using FTIR, the functional groups of the isolated AP fibers were examined, and TG analysis was used to look into the thermal degrading behaviour of the fibers treated with potassium permanganate (KMnO4) Due to their low density (520 kg/m3) and high cellulose content (55.4%), they have excellent bonding qualities. Additionally, tensile tests were used for mechanical characterisation to assess their tensile strength (685 MPa) and elongation.

This research assesses the feasibility of recycling copper mine tailings (CMT) by analyzing the durability and mechanical characteristics of cement mortar using these tailings as filler additives. CMT are mineral wastes generated during the process of mining. In this work, specimens of cement mortar were incorporated with up to 30 wt.% of a CMT. Bulk density, dynamic modulus of elasticity, apparent density, ultrasonic pulse velocity, flexural and compressive strengths tests were evaluated. Total amount of voids, sorptivity, water absorption and chemical resistance tests were also obtained to evaluate the mortar durability. When 10 wt.% CMT was incorporated, overall amount of voids in the mortar was reduced by 20% and mechanical performance was improved by 16% after 28 days. The flexural strength of the mortar was also found to increase, with the 20% wt.% CMT mortar incorporation reaching a flexural strength of 5.89 MPa. Thus represents 16% increase compared to the control 0% CMT strength. The results indicated that there was not a perfect correlation between these results and the mechanical strength results for the 15 and 20 wt.% CMT mortars. In addition, the CMT acts as a protective barrier against harmful chemicals. The results of this research indicate that reusing CMT by incorporating into cement mortar is a feasible method for their recycling. Mortar made with as much as 15 wt.% CMT presented the same strength and durability as mortar with traditional sand and cement.

In recent years, there has been growing interest in exploring natural fiber reinforced composites as potential alternatives to conventional materials in various structural applications. The aim of this study on Acacia pennata fibers (APFs) and treating them with benzoyl chloride was to explore their potential as reinforcement in construction-related materials. The aim was to investigate the physico-chemical, thermal, and mechanical properties of these fibers to understand their suitability for applications in concrete reinforcement, retrofitting, roofing, and wall panels. By enhancing the understanding of the treated fibers' characteristics, this study contributes to the development of sustainable and high-performance construction materials. The fibers were extracted using both water retting and chemical retting methods. The physico-chemical properties of the fibers were assessed through X-ray diffraction (XRD) analysis, which determined a calculated crystalline index (CI) of 72.14% and a crystalline size of 2.6 nm. Thermo-gravimetric analysis was conducted to evaluate the thermal stability of the APFs, revealing a temperature of 366°C and a maximum degradation temperature of 226.7°C. Mechanical analysis included measurements of the APFs' tensile strength (467.86 MPa), tensile modulus (14.62 GPa), microfibrillar angle (14.79˚), and elongation at break (3.2%). The findings derived from these analyses suggest that the APFs that underwent treatment exhibit desirable mechanical characteristics, rendering them a viable option for utilization in construction-related materials like reinforcement in concrete, retrofitting, roofing and wall Pannels. This research presents a novel exploration of Acacia pennata fibers (APFs) treated with benzoyl chloride, aiming to establish their potential as reinforcements for construction materials. While natural fiber-reinforced composites have drawn interest, the unique application of APFs in construction and their treatment with benzoyl chloride to enhance properties remain relatively unexplored in the literature. This study fills a significant gap and contributes to the advancement of sustainable and high-performance construction materials by utilizing treated APFs. The results highlight the remarkable capability of these fibers to enhance the properties of composite materials in the construction industry.

Modified cement mortar plays a major role in enhancing the properties of conventional cement mortar such as strength, durability, better adhesion, reduce porosity and shrinkage and improve workability. Certain modifiers, like industrial by-products, can be incorporated into mortars to promote sustainability and reduce environmental impact. The main aim of this study is to develop Super Absorbent Polymer Modified cement mortars with Nano Silica/GGBS. In this study, conventional cement mortar blended with Nano Silica and Super Absorbent Polymer (SAP) as one combination then GGBS and SAP blended mortar as another combination was examined to mitigate the negative impact of SAP. Ternary Blended cement mortars prepared with various SAP dosages of 0.25% of cement and 0.5% of cement. Nano-Silica is an additive used in the range of 1%, 1.5%, and 2% of the weight of cement. A combination containing GGBS and SAP, GGBS is a replacement for cement in the range of 15%, 30%, and 45% to the weight of cement. The combined effect of altering SAP and Nano-silica/GGBS composition on the mechanical, durability, and microstructural properties were studied using experimental investigation. Peak improvement in the compressive strength of the control mix of 6.52% is noted in the mix combination that contains 0.25% SAP and 15% GGBS replacement. The durability test revealed that the weight loss minimized by 19.58% and strength loss minimized by 36.17% due to acid attack is noted in the combination of GGBS and SAP. Weight loss minimized by 36.17% and strength loss minimized by 22.71% due to sulphate attack is noted in a mix containing GGBS. From experimental investigation, 30% & 45% GGBS replacement in place of cement had no significant improvement in mechanical, durability, and microstructural properties compared to 15% GGBS replacement, which optimum obtained in this study to alleviate the negative consequence of SAP when used as an internal curing agent.

One crucial property of concrete, particularly in construction, is its thermal conductivity, which impacts heat transfer through conduction. For example, reducing the thermal conductivity of concrete can lead to energy savings in buildings. Various techniques exist for measuring the thermal conductivity of materials, but there is limited discussion in the literature about suitable methods for concrete. In this study, the transient line source method is employed to evaluate the thermal conductivity of concrete samples with natural and synthetic fibers after 7 and 28 days of curing. The results indicate that concrete with hemp fiber generally exhibits higher thermal conductivity values, increasing by 48% after 28 days of curing, while synthetic fibers have a minimal effect. In conclusion, this research opens the door to using natural alternatives like hemp fiber to improve concrete’s thermal properties, providing alternatives for thermo-active foundations and geothermal energy piles which require high thermal conductivities.

The use of plastic waste as a partial or complete replacement for coarse aggregate in concrete mixtures has been studied in recent years. However, the quality and quantity of coarse plastic waste particles have been a challenge. This study aims to investigate the mechanical performance of concrete with Bakelite plastic waste as a partial replacement for coarse aggregate. Six different concrete mixtures with various Bakelite dosages, ranging from 0 % to 10 %, were tested. The results indicate that the addition of Bakelite plastic alters the behaviour of the concrete and reduces compressive and flexural strengths at lower dosages. The inclusion of Bakelite waste in concrete mixtures generally leads to a decrease in compressive and split tensile strength, with the exception of the mixture containing 6 % Bakelite, which showed increased strength. Although there is a slight reduction in flexural strength, Bakelite waste prevents sudden specimen breakage and maintains specimen integrity. The ultimate load capacity of reinforced concrete beams with Bakelite waste is generally lower compared to the control beam, except for the 8 % waste Bakelite beam which demonstrated a similar ultimate load capacity of 60 kN. Although managing Bakelite waste can be difficult because it can lead to the creation of microplastics in landfills over time, utilizing Bakelite waste in concrete can be a sustainable method of waste management. The innovative use of Bakelite waste as a partial replacement for coarse aggregate in concrete offers a sustainable solution to the problem of waste management and addresses the environmental concerns related to the disposal of non-biodegradable plastics. This research provides a practical solution for developing eco-friendly and cost-effective construction materials while promoting sustainable waste management practices.

Micronized biomass silica (MBS) and ground granulated blast furnace slag (GGBS) are agro-industrial byproducts generated by incinerating of rice husk (grinding in jar mill) and blast furnaces that used produce iron, respectively. MBS accounts for 20% of the world's total paddy output of 590 million tons. These by-products (MBS and GGBS) have a high concentration of amorphous silica, which is utilized as a mineral additive in concrete. This amorphous silica interacts with hydration products, resulting in the formation of additional CSH gel. This improves concrete's strength and durability properties. Therefore, it is proven that inclusion of agro-industrial by-products in concrete helps to promote sustainable and greener development, which in turn reduces carbon footprints and waste that must be disposed of in landfills. There have been few investigations on concrete using MBS and demonstrated the great potential of employing MBS as a cement substitute or additive in normal concrete. Also, the utilization of MBS as partial replace to GGBS in geopolymer concrete (GPC) with different molarity is a novel aspect of this study. However, this study has the aim and limit to develop a high-strength eco-friendly GPC with agro-industrial byproducts (MBS and GGBS) for use in sustainable construction. The impact of incorporating MBS as a partial replacement of GGBS on compressive and split tensile strengths, sorptivity, and chloride permeability was tested up to the age of 28 days. MBS was used to replace GGBS in varying percentages in the preparation of concretes. MBS were used in concrete at 0%, 10%, 20%, and 30% replacement by weight. It was discovered that a GPC combination containing MBS 20% and the balance GGBS as the binder had the best performance in terms of its strength and durability. The compressive strengths of all GPC mixtures exceeded the intended design strength. The main findings of this study demonstrated clearly that MBS may be employed as a binder in the production of GPC.

Artificial aggregate (AF), i.e., silico manganese (SiMn) slag aggregate, is a byproduct of ferromanganese and silico manganese alloy production. The utilization of industrial waste and industrial byproducts in construction has increased the aim of conserving natural resources to nurture a pollution-free environment. The current study examines the performance of the use of artificial aggregate (AF) and partial replacement of cement with fly ash (FA). The properties of fresh concrete, as well as the compressive and flexural strength and split tensile strength of concrete were evaluated. Seven mix proportions were prepared for M30-grade concrete. The first was a control mix (with 0% AF and FA), three other mixes contained varying amounts of AF (20%, 40%, and 60%) as a partial replacement of CA with AF. The average compressive strength of the control SCC was found to be 32.87 MPa (megapascals) at the age of 28 days, and after replacing 20% natural aggregate with artificial aggregate, the compressive strength increased by 8.27%, whereas for 40% and 60% replacement, it decreased by 4.46% and 12.55%, respectively. Further investigation was performed on the optimum value obtained by replacing 20% of CA with AF. At this percentage, cement was replaced by FA at (15%, 25%, and 35%) where at 15%, the average compressive strength increased by 7.41%, whereas for 25% and 35% replacement, it decreased by 7.47% and 17.19%, respectively. For SCAF20 and SCF15, all strengths were at maximum due to the increase in its density. The findings show that the development of advanced construction materials is environmentally sustainable.

This research aimed to determine how a super absorbent polymer affects the microstructural characteristics and water retention kinetics of a new composite made by substituting granite pulver (GP) and fly ash (FA) for cement. Understanding the mechanics of water movement is crucial for comprehending the effectiveness of autogenous curing. Several experiments were conducted to analyze the water mitigation kinetics of super absorbent polymer (SAP) in the hydrating cement paste of autogenous cured self-compacting concrete (GP-ACSSC) mixtures. In the first hours following casting, water sorptivity, water retention, and hydration tests were carried out. The effects of various concentrations of SAP and GP, which was utilized as an alternative cement for the production of sustainable concrete that leads to reduction in carbon footprint, on the autogenous cured self-compacting concrete with reference to the abovementioned properties were explored. The investigation showed that releasing the curing water at a young age, even around the beginning of hydration, allowed homogenous and almost immediate distribution of water across the full cured paste volume, which improved the water retention kinetics. Compared to the control mixtures, the addition of SAP up to 0.6% and the substitution of cement with GP up to 15% had favorable impacts on all water kinetics parameters.

The only biotic factor that can satisfy the needs of human species are plants. In order to minimize plastic usage and spread an immediate require of environmental awareness, the globe urges for the development of green composite materials. Natural fibers show good renewability and sustainability and are hence utilized as reinforcements in polymer matrix composites. The present work concerns on the usage of Butea parviflora fiber (BP), a green material, for high end applications. The study throws light upon the characterization of raw and potassium hydroxide (KOH)–treated Butea Parviflora plant, where its physical, structural, morphological, mechanical, and thermal properties are analyzed using the powder XRD, FTIR spectroscopy, FESEM micrographs, tensile testing, Tg-DTA, Thermal conductivity, Chemical composition, and CHNS analysis. The density values of untreated and KOH-treated fibers are 1.238 g/cc and 1.340 g/cc, respectively. The crystallinity index of the treated fiber has significantly increased from 83.63% to 86.03%. The cellulose content of the treated fiber also experienced a substantial increase from 58.50% to 60.72%. Treated fibers exhibited a reduction in both hemicelluloses and wax content. Spectroscopic studies registered varying vibrations of functional groups residing on the fibers. SEM images distinguished specific changes on the raw and treated fiber surfaces. The Availability of elements Carbon, Nitrogen, and Hydrogen were analyzed using the CHNS studies. The tensile strength and modulus of treated fibers has risen to 192.97 MPa and 3.46 Gpa, respectively. Thermal conductivity (K) using Lee’s disc showed a decrement in the K values of alkalized BP. The activation energy Ea lies between 55.95 and 73.15 kJ/mol. The fibers can withstand a good temperature of up to 240 °C, presenting that it can be tuned in for making sustainable composites.

Geopolymer concrete and mortar have evolved over the years as potential alternatives for reducing the greenhouse gases associated with cement production. This current research was aimed at investigating the optimum dosage and concentration of sodium hydroxide required to leach out silica and alumina oxides in the fly ash for geopolymerization to take place. Blackish grey fly ash from Morupule, Botswana, was synthesized by varying sodium hydroxide (NaOH) of 98% purity between 8 M and 14 M, respectively. The ratio influence of sodium hydroxide to fly ash in dissolving the oxides was carried out at the values of 0.55, 0.62, and 0.75. The results showed that the workability of the geopolymer mortar and paste decreased with the increase in the ratio of fly ash to alkaline activator. The highest workability was achieved at a ratio of 0.75 : 1. The compressive strength, setting time, and workability of geopolymer mortar and paste can be controlled by adjusting the ratio of fly ash to alkaline activator. A ratio of 1.5 : 1 was found to be the most suitable for achieving high compressive strength, while a ratio of 0.75 : 1 was found to be the most suitable for achieving high workability. Furthermore, the workability values were in the range of 105 to 143 mm, while the ranges of initial and final setting times were found to be between 280–350 and 950–1170 minutes, respectively. This study is significant because no previous study has carried out geopolmerization of the Morupule fly ash as a result of its unique characteristics. These findings have important implications for the development of sustainable construction materials. The main finding was that for optimum reaction to take place, and NaOH/fly ash ratio should be kept at 0.55 and molarity of 12 to avoid leaching of other oxides that might weaken the strength.

Demolition of existing deteriorated structures and construction of the new structures is a costly, time-consuming, and resource-intensive process. Repair of concrete beams and strengthening techniques for existing reinforced concrete elements is a resource-saving exercise that is time-saving also. In this work, a repair material using metakaolin-based alkali-activated concrete (AAC) is developed with high early compressive strength and split tensile strength designed with proper mix proportions. The flexural strength of reinforced concrete beams was determined without the new repair material. The specimens were loaded until failure and the deflected portion of the RC beam was then confiscated using breakers. The confiscated portion is subsequently replenished with metakaolin-based AAC and flexural strength and bond characteristics were determined. Shrinkage length changes were also measured. The metakaolin-based AAC with 15% metakaolin had a high stiffness and increased flexural strength up to 14.4% compared to the specimen before repair. It also exhibited a significant bonding with the concrete substrate with less shrinkage and improved strength.

Concrete is a quasi-brittle material whose basic mechanical properties are size-dependent. Due to simple substitution in profoundly congested support structures without experiencing any consolidation, non-segregation property, and smooth finishing, it could be an exceptionally great choice in the concrete industry. The research object is the size effect on the flexural behavior of reinforced self-compacting concrete (SCC) beams by varying depth, length, and span. The length to depth ratio (aspect ratio) was 3.88, 5.38, 8.75, 11.5, and 15.38. SCC trial mixes were technologically advanced using FA (FA) as filler material and conplast SP430 as Super-plasticizer (SP). The workability properties were determined via the T50 cm slump flow, slump flow, U-box, V-funnel, J-ring, and L-box tests. FA (30%) with SP (1.9%) is satisfied with all the requirements of SCC as per EFNARC guidelines, and the designed compressive strength of concrete was obtained as 30 MPa. A total of six beams with various sizes, such as depths of 100 mm, 150 mm, and 200 mm, and lengths of 900, 1700, and 2200 mm, were cast with 1.2% tensile reinforcement bars. Based on the depth effect of beams, the load-deflection behavior, flexural strength, ductility index, and stiffness were studied. It is revealed that there is a decrease in strength properties by increasing the depth of beams during the static load conditions. Beams with a length equal to 1700 mm reached the best performance. It was also found the most advantageous l/d proportion, in terms of mechanical performance, is equal to 5.38.

Incorporating waste byproducts into concrete is an innovative and promising way to minimize the environmental impact of waste material while maintaining and/or improving concrete’s mechanical characteristics and strength. The proper application of sawdust as a pozzolan in the building industry remains a significant challenge. Consequently, this study conducted an experimental evaluation of sawdust as a fill material. In particular, sawdust as a fine aggregate in concrete offers a realistic structural and economical possibility for the construction of lightweight structural systems. Failure under four-point loads was investigated for six concrete-filled steel tube (CFST) specimens. The results indicated that recycled lightweight concrete performed similarly to conventional concrete when used as a filler material in composite steel tube beams. The structural effects of sawdust substitution on ultimate load and initial stiffness were less substantial than the relative changes in the material properties, and the ultimate capacity of the tested samples decreased moderately as the substitution percentage of sawdust increased. Moreover, the maximum load capacity was observed to decrease by 6.43–30.71% for sawdust replacement levels between 5% and 45.1% across all tested samples. Additionally, when using lightweight concrete with 5% sawdust, the moment value of the CFST sample was reduced by 6.4%. Notably, the sawdust CFST samples exhibited a flexural behavior that was relatively comparable to that of the standard CFST samples.

The steel-concrete composite column comprises a steel core and surrounding concrete. The purpose of the system is to provide analysis and design techniques for a newly invented class of laced steel-concrete composite short columns for cyclic axial loads. To minimize the increasing density issues associated with nominal strength concrete and in consideration of the depletion of natural resources required to produce concrete, factory-obtained lightweight sintered fly ash aggregates with and without basalt fiber are employed. The normal-weight concrete containing basalt fiber is shown to be more ductile than any other column. The axial deformation of columns LNA and LSA at failure was found to be 3.5 mm, whereas columns LNAF and LSAF reached an axial shortening of 4.5 mm at failure. The column LSAF was found to have 5.3% more energy absorption than the LSA and 11.5% less than the column LNAF. It was observed that the rigidity of these fabricated components had been enhanced. It was found that the section configuration with a lacing system had improved confinement effects and ductility. Comparing the finite element analysis to the experimental data revealed a strong connection with numerical modeling, with a variance of around 8.77%.

Due to the COVID-19 epidemic, biomedical waste management has overwhelmed both developed and developing nations. It is now a critical issue that has to be addressed with minimal possible adverse impact on the environment. This study introduced a technique of recycling face masks into polypropylene fibers for use in concrete. This proposed recycling process provides complete disinfection of contaminated clinical waste and offers the opportunity to transform the characteristics of an end product. Microfibers manufactured from recycled medical masks were subjected to testing. According to the results, polypropylene is the primary component of this research program. Two batches of concrete were made, one with the inclusion of masks as polypropylene fibers and another that performed as a control mix. The modified mortar was compared to the control mix in split tensile, flexure, compressive strength, and water absorption. Compressive strength was found to be improved by about 17%, and tensile strength to be increased by around 22% when mask fibers were incorporated. This research introduced a novel approach for disposing of waste masks and established the preliminary viability of upcycling trash face masks towards mortar concrete production.

The most valuable components of coal fly ash are cenospheres. Cenospheres are hollow spherical particles produced during the coal-burning processes. As a result of their excellent characteristics, such as high workability, high heat resistance, low bulk density, and high strength, cenospheres can be used in the manufacturing of lightweight cement concrete. The research efforts and outcomes are to produce long-lasting cement-based lightweight concrete (LWC) composites with good mechanical properties. The novelty of this investigation is to determine the cement concrete strength when silica fume (SF) and cenospheres (CS) were used as a replacement for cement. Throughout the experiments, a consistent substitution of 12% silica fume was incorporated into cement mass. Silica is used as a micro filler and pozzolanic reactant to strengthen concrete. The concrete mixtures were tested to ensure they met the requirements of the lightweight concrete in terms of their mechanical, physical, and durability qualities. According to the findings, lightweight concrete standards were met, and environmental sustainability was improved with the use of these mix proportions. Concrete specimen’s self-weight decreases by 35% with 30% cenosphere as a replacement. The micrograph shows the lack of portlandite is filled by mullite and other alumino silicates from the cenosphere. In order to achieve sustainability in concrete manufacturing, these mixtures can be suggested for the making of structural LWC that makes use of a large volume of industrial waste while conserving cement and natural resources.

This study emphasizes the importance of utilizing biodegradable material Butea parviflora (BP) fiber for sustainable solutions. BP fiber offers numerous ecological benefits, such as being lightweight, biodegradable, and affordable to recycle. The study examines the effects of potassium permanganate (KMnO4) treatment on BP fiber and analyzes its physical and chemical behavior using various methods, including X-ray Diffraction (XRD) analysis, tensile testing, thermogravimetric analysis, thermal conductivity, Scanning Electron Microscopy (SEM), and Fourier Transform Infrared spectroscopic (FTIR) analysis. The results demonstrate that BP fiber possesses low density (1.40 g/cc) and high cellulose content (59.4%), which fosters compatibility between the matrix and resin. XRD analysis indicates a high crystallinity index (83.47%) and crystallite size (6.4 nm), showcasing exceptional crystalline behavior. Treated fibers exhibit improved tensile strength (198 MPa) and Young’s modulus (4.40 GPa) compared to untreated fibers (tensile strength—92 MPa, tensile modulus—2.16 GPa). The Tg-DTA thermograms reveal the fiber’s thermal resistance up to 240 °C with a kinetic activation energy between 62.80–63.46 KJ/mol. Additionally, the lowered thermal conductivity (K) from Lee’s disc experiment suggests that BP fiber could be used in insulation applications. SEM photographic results display effective surface roughness for composite making, and FTIR studies reveal vibrational variations of cellulosic functional groups, which correlates with increased cellulosic behavior. Overall, the study affirms the potential of BP fiber as a reinforcing material for composite-making while emphasizing the importance of utilizing biodegradable materials for sustainability.

The present study concerns the physico-chemical, structural, mechanical and thermal characterization of Acacia pennata, a natural and almost inexpensive fibre, as a potential reinforcement in polymer composites. The effect of treating the fibre with sodium acetate to increase its qualities has been seen through the use of thermogravimetric analysis, scanning electron microscope (SEM) analysis, X-ray diffraction (XRD), mechanical property tester, and Fourier transform infrared spectroscopy (FTIR). According to XRD analysis, the elimination of lignin and wax-like impurities resulted in an increase in the AP fibre’s crystalline index (79.73%). The fibre’s thermal stability was also discovered to be 365 °C. Tensile strength (557.58 MPa) and elongation at break both increased by 2.9% after treatment with sodium acetate. The surface nature and quality of AP fibres improved after sodium acetate treatment. It was confirmed by the reduction of chemical compositions (such as hemicellulose, lignin and pectin). Given its density, the fibre can be suggested as a reinforcement in polymer composites for light-weight applications because its lightweight property will be more useful for composite manufacturing.

Chile’s reinforced concrete (RC) design is based on ACI 318-08, where high-strength reinforcement is not allowed in seismic force-resistant members. In 2019, new requirements adopted by ACI 318 permitted the incorporation of high-strength reinforcement in walls. This study compared the seismic performance of two Chilean 20-story residential buildings on soft soil, one designed with traditional Grade 60 and the other with high-strength Grade 80 reinforcement. The performance was assessed in terms of the probability of exceeding the ASCE 41 limit states during a 50-year lifecycle. Analyses showed that both buildings had similar seismic performance. However, the reduction in reinforcement in the Grade 80 building was close to 18%. It is concluded that using high-strength reinforcement in a typical wall building implies a significant reduction in the reinforcement used without affecting the seismic performance.

Today, new materials based on natural fibres have been emerging day by day to completely eradicate plastics to favour our environmental nature. In this view, the present work is based on the extraction and characterisation of the novel root fibres of the Zea mays (Zm) plant, grown by the hydroponic method. Both the dried untreated and alkali treated root fibres are investigated using a variety of structural, morphological, thermal, elemental and mechanical tests by subjecting both the samples to p-XRD, FT-IR, SEM-EDAX, TGA-DTA, CHNS and tensile strength analyses. Thermal conductivity of the untreated and treated fibres is found using Lee’s disc experiment. From p-XRD analysis, the Crystallinity Index, Percentage Crystallinity and Crystallite size of the samples are found. FT-IR studies clarify the different vibrational groups associated with the fibre samples. SEM images show that the surface roughness increases for the chemically treated samples, such that it may be effectively utilised as reinforcement for polymeric composites. The diameter of the fibre samples is found using SEM analysis. According to the EDAX spectrum, Zm fibres in both their raw and processed forms have high levels of Carbon (C) and Oxygen (O). The TGA-DTA tests revealed that the samples of natural fibre have good thermal characteristics. CHNS studies show that Carbon content is high for these samples, which is the characteristic of many natural fibres. Chemical analysis is used to ascertain the prepared samples’ chemical makeup. It reveals that both samples have significant amounts of cellulose. The density of the fibres is found to be in the range 0.3–0.6 g/cc, which is much less than any other natural fibre. Therefore, it can be used in light weight applications. From the tensile strength analysis, physical properties such as Young’s modulus and micro-fibril angle are determined. The fibres in the roots exhibit a lower tensile strength. Thus, these fibres can be used in powdered form as reinforcement for natural rubber or epoxy composites. After examining all of its properties, it could be reasonably speculated that Zea mays root fibres can be considered as an efficient reinforcement for various matrices to produce attractive bio-composites.

Natural fiber (NF) is one of the many resources that nature has provided. NFs decompose quickly and are biodegradable, renewable, and cost-effective. It may be scavenged from a variety of plant and animal sources. They are employed as reinforcing materials in polymers for NF composite development. Because of its environmental friendliness and long-term survivability, NF is growing in appeal among academics and researchers for usage in polymer composites. This study aims to offer a thorough evaluation of the most suitable and widely utilized natural fiber-reinforced polymer composites (NFPCs), along with their manufacture, processing, and applications. It also defines several external treatments of NF and their influence on the characteristics of NFPCs. The characteristics of NFPCs are affected by fiber supply, fiber type, and fiber structure. Numerous physical and chemical treatments were tested to see how they affected the thermal and strength properties of natural fiber-reinforced thermoplastic and thermosetting composites. Several polymer composite fabrication techniques were also studied. NFPCs have several disadvantages, notably low fire protection, poor strength properties, and greater moisture absorption, which have prevented their application. It is shown how NFPCs are employed in a variety of industries, particularly automotive and research industries. The review discovered that intentionally changing the regular fiber enhanced the thermochemical and physico-mechanical properties of the NFPCs by means of improving the grip between the fiber surface and the polymer framework. This study aims to provide important and fundamental facts on NF and their composites, which will aid in new investigations, the creation of a creative framework for polymer composite types, and the achievement of Sustainable Development Goals.

In this paper, the influence of design parameters on the strength of steel–concrete composite shear walls is investigated by means of finite element (FE) simulations. The shear wall typology studied in this paper consists of multiple composite plate shear wall-concrete encased on one or both sides of the plates. The FE models include contact technology to capture debonding between concrete and steel, tensile cracking in concrete, and large deflection theory involving local instabilities. Some design parameters considered in this work are the height-to-width ratio of the steel plates and their thickness, number of steel plates, the cross-section of the columns, and the height-to-width ratio of the shear wall. Furthermore, a sensitivity analysis of the normalised shear strength per unit cost of structure for these design parameters is also studied. Our numerical predictions are validated successfully with experimental data reported in the literature, revealing the predictive capabilities of the model. The present results provide further insight into the structural behavior of steel–concrete composite shear walls and pave the way for the future development of more efficient and innovative steel–concrete composite systems.

Natural fiber composites are becoming an alternate material to synthetic fiber composites, and the use of eggshell bio-filler has been explored in polymer composites as environmental protection. Jute, coir, and sisal fibers were utilized in this research to make composites out of natural fibers. Polymer composites were made using epoxy resin with different amounts of eggshell powder (ESP) as fillers (2%, 4%, 6%, 8%, and 10% of weight). The mechanical and biodegradability properties of the synthesized composites were investigated. The testing results showed that composites with an optimum percentage of 6% ESP as filler improved mechanical characteristics significantly in all three fiber composites. Among the three fibers, coir fiber with 6% ESP added showed a substantial increase in tensile, flexural, impact, and hardness strength properties by 34.64%, 48.50%, 33.33%, and 35.03%, respectively. In addition, the percentage weight loss of coir fiber composites at 9 weeks is noteworthy in terms of biodegradability testing. As a result, epoxy composites containing eggshell fillers could be employed in applications requiring better tensile, flexural, impact, and hardness strength.

The objective of this paper is to provide a comprehensive study about the performance of concrete using mixed coarse recycled aggregate (MCRA) as an alternative for natural aggregate (NA) at replacement levels of 0, 30, 60, and 100%, which can greatly reduce the environmental pollution by incorporating the construction and demolition wastes in the reproduction of concrete. The focus of this study was to use the raw MCRA that was directly obtained from a recycling plant and not further processed. Initially, MCRA was studied to ascertain if its property meets the recommended Indian standards for natural aggregates. Using the slump test, the workability of freshly prepared concrete with a characteristic strength of 30 MPa was assessed. Additionally, the mechanical performance of concrete was assessed on the specimens prepared in the different forms: cubes, cylinders, and beams. Moreover, Scanning Electron Microscopy (SEM) with EDAX, XRD, and FTIR were used to study the microstructural behavior of selected optimum and control mixes at 7 and 28 days of curing. The studies revealed that a higher MCRA content improved the workability of concrete and 30% replacement of MCRA improved the compressive strength by 11.01, 6.98, 6.19, and 14.24% at 7, 28, 56, and 90 days respectively. At the same time, the 30% replacement of the MCRA mix showed an improved split tensile and flexural strength by 2.92 and 6.26%, respectively. The microstructural analysis showed that the optimum mixture had a more condensed microstructure. Therefore, 30% replacement of MCRA can be incorporated in the characteristic strength of concrete of 30 MPa. In particular, MCRA incorporation had a positive influence similar to conventional concrete on the physical, mechanical, and microstructural properties, which can increase the utilization of all kinds of directly obtained construction and demolition wastes to increase the circular economy in the construction sector.

Autoclaved aerated concrete (AAC) is one of the most common types of lightweight cellular concrete, having a density of approximately one-fourth of that of conventional plain cement concrete. The use of industrial waste materials in concrete as a replacement for cement has garnered a lot of attention in recent years as a way to reduce the environmental effect of concrete. In this study, an attempt has been made to study the effect of AAC blocks made of industrial wastes such as fly Ash (FA) and ground granulated blast furnace slag (GGBS). Fly ash, along with different dosages of GGBS, was used as a partial replacement for cement in the production of AAC. For all the different dosages, microstructural analysis was performed using a Scanning electron microscope (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDAX), and Fourier transform infrared spectroscopy (FTIR). Mechanical performances of AAC were determined by conducting various tests like compressive strength, modulus of rupture, dry density, and water absorption. The results revealed that the dosage of “15% GGBS + 85% cement” has maximum compressive strength, modulus of elasticity, and modulus of rupture made of Class F Fly Ash when compared to Class C Fly Ash based AAC blocks. Besides, the incorporation of GGBS in the manufacturing process would increase the compressive strength of AAC up to 68%. Hence, it is recommended to use 15% GGBS + 85% cement as a potential rate of replacement, to improve the mechanical properties of AAC blocks significantly.

Sandwich beams are preferable for aerostructure and marine structures due to their high mechanical strength, durability, stiffness, and fatigue resistance. This paper presents a study on the flexural behavior of sandwich beams made of self-compacting concrete comprising a polystyrene inner core with wire mesh reinforcement. The effect of the design parameters such as the inner core area, percentage of tension reinforcement, and wire mesh on the moment carrying capacity and failure modes of sandwich beams was analyzed. Ten beams were cast and tested to failure with simply supported end conditions and they were classified into three different groups. The longitudinal section of the inner core area was varied by 0% (control beam), 25%, 50%, and 75% of the gross area. The tension reinforcement ratio varied between 0.6 and 1.5%. In addition, the effect of the wire mesh in shear and flexural resistance was studied. The load-carrying capacity of sandwich beams increased with flexural reinforcement. In addition, the welded wire mesh improved the sandwich beams’ flexural and shear performance. The conventional expressions for the moment of resistance were valid for sandwich beams, whereas the shear strength expressions overestimated the capacity; therefore, modifications were suggested. The refined models had a significant agreement with the experimental results.

The construction industry relies heavily on concrete as a building material. The coarse aggregate makes up a substantial portion of the volume of concrete. However, the continued exploitation of granite rock for coarse aggregate results in an increase in the future generations’ demand for natural resources. In this investigation, coconut shell was used in the place of conventional aggregate to produce coconut shell lightweight concrete. Class F fly ash was used as a partial substitute for cement to reduce the high cement content of lightweight concrete. The impact of steel fiber addition on the compressive strength and flexural features of sustainable concrete was investigated. A 10% weight replacement of class F fly ash was used in the place of cement. Steel fiber was added at 0.25, 0.5, 0.75, and 1.0% of the concrete volume. The results revealed that the addition of steel fibers enhanced the compressive strength by up to 39%. The addition of steel fiber to reinforced coconut shell concrete beams increased the ultimate moment capacity by 5–14%. Flexural toughness was increased by up to 45%. The span/deflection ratio of all fiber-reinforced coconut shell concrete beams met the IS456 and BS 8110 requirements. Branson’s and the finite element models developed in this study agreed well with the experimental results. As a result, coconut shell concrete with steel fiber could be considered as a viable and environmentally-friendly construction material.

The production and utilization of concrete and concrete-based products have drastically increased with the surge of construction activities over the last decade, especially in countries such as China and India. Consequently, this has resulted in a corresponding increase in the energy used for the production of ready-mixed concrete. One approach to reduce the cost of concrete manufacturing is to reduce the energy required for the manufacturing process. The main hypothesis of this study is that the power required for mixing the concrete can be reduced through the use of mineral admixtures in the mix design. Optimization of energy consumption during mixing using admixtures in concrete manufacturing is the predominant focus of this article. To achieve this objective, power consumption data were measured and analyzed throughout the concrete mixing process. The power consumption curve is the only source to distinguish the behavior of the different materials used in the concrete in a closed chamber. In the current research, fly ash and ground granulated blast-furnace slag (GGBS) were used as mineral admixtures to produce ready-mixed concrete. The experimental study focused on the influence of GGBS and fly ash on power consumption during concrete mixing. The results indicated that the use of a higher content of GGBS is more beneficial in comparison to the use of fly ash in the mix due to the lower mixing time required to achieve homogeneity in the mixing process. It was found that the amount of energy required for mixing is directly related to the mixing time for the mix to achieve homogeneity.

Concrete technology is adopted worldwide in construction due to its effectiveness, performance, and price benefits. Subsequently, it needs to be an eco-friendly, sustainable, and energy-efficient material. This is achieved by replacing or adding energy-efficient concrete materials from industries, such as ground granulated blast furnace slag, steel slag, fly ash, bottom ash, rice husk ash, etc. Likewise, copper slag is a waste material produced as molten slag from the copper industry, which can be used in concrete production. Copper slag can perform roles similar to pozzolans in the hydration process. This paper extends the comparative study of copper slag concrete with polypropylene fiber (PPF) subjected to destructive and non-destructive testing. Under destructive testing, compressive strength of concrete cubes, compressive strength of mortar cubes, splitting tensile tests on cylindrical specimens, and flexural tests on plain cement concrete were conducted and analysed. Ultrasonic pulse velocity and rebound hammer tests were performed on the samples as per IS13311-Part 1-1992 for non-destructive testing. The 100% replacement of copper slag exhibited a very high workability of 105 mm, while the addition of 0.8% PPF decreased the flowability of the concrete. Hence, the workability of concrete decreases as the fiber content increases. The density of the concrete was found to be increased in the range of 5% to 10%. Furthermore, it was found that, for all volume fractions of fiber, there was no reduction in compressive strength of up to 80% of copper slag concrete compared to control concrete. The 40% copper slag concrete was the best mix proportion for increasing compressive strength. However, for cement mortar applications, 80% copper slag is recommended. The findings of non-destructive testing show that, except for 100% copper slag, all mixes were of good quality compared to other mixes. Linear relationships were developed to predict compressive strength from UPV and rebound hammer test values. This relationship shows better prediction among dependent and independent values. It is concluded that copper slag has a pozzolanic composition, and is compatible with PPF, resulting in good mechanical characteristics.

To find the energy required during the mixing process of self-compacting concrete in a ready-mixed concrete plant and correlate the results with the yield stress of concrete. Power consumption required during the mixing of concrete is measured with a wattmeter connected to the mixing unit’s power supply. A coaxial cylinder viscometer is used to measure the yield stress of concrete. The clamp meter measures the power when the impeller rotates inside the coaxial cylinder viscometer, which is filled with concrete. When the impeller rotates in a coaxial cylinder filled with concrete, the power is measured by a clamp meter. Torque is obtained through the power relationship, which is an essential factor in determining the yield stress. The cost of a rheometer is so high that all construction industries, research institutions, and researchers cannot measure rheological parameters. Nowadays, all rheometers are automated; hence, the cost is very high. Tattersall’s approach of power requirement in mixing the concrete and calculating the yield stress reduces the complexity in determining the rheological parameter.

In general, most highway bridges are constructed using prestressed concrete or steel girders. Mechanical joints are provided at the end of each span, to allow for the expansion of the bridge deck due to shrinkage of concrete, thermal effects, and deflections, among others. Smooth riding ability, low noise, wear resistance, and water tightness should be provided by expansion joints. In recent times, the increased traffic volume, along with heavier vehicle movements, adversely affects the performance of expansion joints in the bridge girder, causing a possible failure in one of the above-mentioned mechanisms. The deterioration of the expansion joint may result in leakage of water, concrete cracking, and potential problems in the underlying substructure. In this paper, we study the pier-pier cap connections in integral bridges subjected to thermal and seismic loads using analytical methods and experimental tests.

Generally, the concrete with higher strength appears to produce brittle failure more easily. However, the use of mineral admixture can help in enhancing the ductility, energy dissipation, and seismic energy in the designed concrete. This paper presents energy absorption capacity, stiffness degradation, and ductility of the copper slag (CS) admixed reinforced concrete with fly ash (FA) beams subjected to forward cyclic load. The forward cyclic load was applied with the help of servo-hydraulic universal testing machines with 250 kN capacity. Twenty-four beams with a size of 100 mm × 150 mm × 1700 mm made with CS replaced for natural sand from 0% to 100% at an increment of 20%, and FA was replaced for cement from 0% to 30% with an increment of 10% were cast. Beams are designed for the grade of M30 concrete. Based on the preliminary investigation results, compressive strength of the concrete greatly increased when adding these two materials in the concrete. Normally, Grade of concrete can change the behaviour of the beam from a brittle manner to be more ductile manner. So, in this work, flexural behaviour of RC beams are studied with varying compressive strength of concrete. Experimental results showed that the RC beam made with 20% FA and 80% CS (FA20CS80) possesses higher ultimate load-carrying capacity than the control concrete beam. It withstands up to 18 cycles of loading with an ultimate deflection of 60 mm. The CS and FA admixed reinforced concrete composite beams have excellent ultimate load carrying capacity, stiffness, energy absorption capacity, and ductility indices compared to the control concrete beam.

This paper represents a first attempt to study the feasibility of using shear wave (SW) ultrasonic probes as pump-wave sources in concrete microcrack detection and monitoring by Nonlinear Ultrasonic Coda Wave Interferometry (NCWI). The premise behind our study is that the nonlinear elastic hysteretic behavior at microcracks may depend on their orientation with respect to the stationary wave-field induced by the pump-wave source. In this context, the use of a SW probe as a pump-wave source may induce the nonlinear elastic behavior of microcracks oriented in directions not typically detected by a conventional longitudinal pump-wave source. To date, this premise is hard to address by current experimental and numerical methods, however, the feasibility of using SW probes as a pump-wave source can be experimentally tested. This idea is the main focus of the present work. Under laboratory conditions, we exploit the high sensitivity of the CWI technique to capture the transient weakening behaviour induced by the SW pump-wave source in concrete samples subjected to loading and unloading cycles. Our results show that after reaching a load level of 40% of the ultimate stress, the material weakening increases as a consequence of microcrack proliferation, which is consistent with previous studies. Despite the lack of exhaustive experimental studies, we believe that our work is the first step in the formulation of strategies that involve an appropriate selection and placement of pump-wave sources to improve the NCWI technique. These improvements may be relevant to convert the NCWI technique into a more suitable non-destructive testing technique for the inspection of microcracking evolution in concrete structures and the assessment of their structural integrity.

Copper slag (CS) is produced during the smelting process to separate copper from copper ore. The object of the experimental research is to find the optimum percentage of CS and PPF volume fraction when CS replaces fine aggregate, and PPF volume fraction when subjected to impact loading. Copper slag was incorporated as 20%, 40%, 60%, 80% and 100% with PPF of 0.2–0.8% with 0.2% increment. The number of blows on failure of the specimen increases as the fibre volume increases. In addition, the energy absorption of composite concrete is higher than that of ordinary concrete. Concrete with up to 40% CS and 0.6% PPF volume shows a 111.72% increase in the number of blows for failure as compared to the control specimen. The impact resistance at failure was predicted by regression analysis, and very high regression coefficients of 0.93, 0.98 and 0.98 were obtained respectively at 7-, 14- and 28-days curing. In addition to regression analysis, a two-parameter Weibull distribution analysis was used to obtain reliable data on the number of blows at first cracking and eventual failure. The energy absorption at 28-day curing period is 1485.81 Nm which is 284% higher than the control mix. Based on the findings, it can be inferred that adding CS up to 60% densifies the microstructure due to its pozzolanic activity, while polypropylene fibre acts as a micro reinforcement, increasing the number of blows.

The aim of this research was to find the best alternative for river sand in concrete. In both geopolymer concrete (GPC) and cement concrete (CC), the fine aggregates are replaced with various sustainable mineral ashes, and mechanical and durability tests are conducted. Specimens for tests were made of M40 grade GPC and CC, with five different soil types as river sand substitute. The materials chosen to replace the river sand are manufactured sand (M-sand), sea sand, copper slag, quarry dust, and limestone sand as 25%, 50%, 75%, and 100%, respectively by weight. GPF50 and CC50 were kept as control mixes for GPC and CC, respectively. The test results of respective concretes are compared with the control mix results. From compressive strength results, M-sand as a fine aggregate had an increase in strength in every replacement level of GPC and CC. Additionally, copper slag is identified with a significant strength reduction in GPC and CC after 25% replacement. Copper slag, quarry dust, and limestone sand in GPC and CC resulted in considerable loss of strength in all replacement levels except for 25% replacement. The cost of GPC and CC is mixed with the selected fine aggregate replacement materials which arrived. Durability and cost analyses are performed for the advisable mixes and control mixes to have a comparison. Durability tests, namely, water absorption and acid tests and water permeability and thermal tests are conducted and discussed. Durability results also indicate a positive signal to mixes with M-sand. The advisable replacement of river sand with each alternative is discussed.

Concrete has served an essential role in many infrastructural projects. Factors including pore percentage, pore distribution, and cracking affect concrete durability. This research aims to better understand pore size distribution in cement-based materials. Micro-computed tomography (micro-CT) pictures were utilised to characterise the interior structure of specimens without destroying them. The pore dispersion of the specimens was displayed in 3D, utilising the data and imaging techniques collected, and the pore volume dispersion was examined using a volume-based approach. Another way to describe heterogeneous pore features is the chord-length distribution, which was calculated from three-dimensional micro-CT scans and correlated with the traditional method. The collected specimens were subjected to physical and mechanical testing. In addition, image processing techniques were used to conduct the studies. The results showed that the chord-length distribution-based pore size distribution is very successful than the traditional volume-based technique. The acquired data could be used for research and to forecast the characteristics of the materials.

Incorporating superabsorbent polymer (SAP), which has the abilities of absorption and desorption in cement mortar, can achieve the effect of internal curing. It is expected that the incorporation of nano-silica will improve the workability and strength in cement mortar/concrete. Hence, this study aims to examine the effect of SAP and nano-silica on the properties of blended cement paste. The experimental investigations via several tests such as consistency, setting time, compressive strength, UPV, and acid test were performed. Based on energy-dispersive X-ray analysis (EDX) test and scanning electron microscopy (SEM) test results, the morphology of hydration products and mineral compositions of cement paste were further analysed, and the mechanism of SAP with 0.2% and 0.3% and NS with lower percentages ranging from 0.5% to 2% on the performance of cement paste was studied. The results exhibited that incorporating SAP in various percentages from 0.5% to 2% prolonged the initial setting time, reduced the fluidity, and increased the water content and formation of pores. In addition, various percentages ranging from 0.5% to 2% of NS were added; thereby, an increase in the hydration process and refining the microstructure was found. The microscopic test results showed that the blended cement paste can effectively improve the denser microstructure and refine the pore structure.

The use of the combination of ultrafine rice husk ash (RHA) and nano silica (NS) enhances the compactness of hardened concrete, but there is still a lack of studies that address the effects of NS and RHA on the workability, mechanical properties and pore microstructure of concrete. This study mainly aims to investigate the influence of the pore size distribution in multiphysics concrete model modified by NS and RHA and to determine the workability and mechanical properties of concrete with NS and RHA. In this work, NS and RHA were used as 0, 5, 10, 15 and 20% replacements of ordinary Portland cement (OPC) in concrete grade M20. Concrete mixed with NS and RHA showed improved performance for up to 10% addition of NS and RHA. Further addition of NS and RHA showed a decrease in performance at 7, 14 and 28 days. The decrease in concrete porosity was also found to be up to 10% when adding NS and RHA to cement. Image processing was performed on the cement-based materials to describe the microstructure of the targeted material without damage. The results from the experimental and tomography images were utilized to investigate the concrete microstructure and predict its inner properties.

Development of sustainable concrete as an alternative to conventional concrete helps in reducing carbon dioxide footprint associated with the use of cement and disposal of waste materials in landfill. One way to achieve that is the use of fly ash (FA) as an alternative to ordinary Portland cement (OPC) because FA is a pozzolanic material and has a high amount of alumina and silica content. Because of its excellent mechanical properties, several studies have been conducted to investigate the use of alkali-activated FA-based concrete as an alternative to conventional concrete. FA, as an industrial by-product, occupies land, thereby causing environmental pollution and health problems. FA-based concrete has numerous advantages, such as it has early strength gaining, it uses low natural resources, and it can be configurated into different structural elements. This study initially presents a review of the classifications, sources, chemical composition, curing regimes and clean production of FA. Then, physical, fresh, and mechanical properties of FA-based concretes are studied. This review helps in better understanding of the behavior of FA-based concrete as a sustainable and eco-friendly material used in construction and building industries.

An experimental investigation is performed on various cold-formed profiled sheets to study the connection behavior of composite deck slab actions using bolted shear connectors. Various profiles like dovetailed (or) re-entrant profiles, rectangular profiles and trapezoidal profiles are used in the present investigation. This experimental investigation deals with the evaluation of various parameters such as the ultimate load carrying capacity versus deflection, load versus slip, ductility ratio, strain energy and modes of failure in composite slab specimens with varying profiles. From the test results the performance of dovetailed profiled composite slabs’ resistance is significantly higher than the other two profiled composite deck slabs.