Search

Nanocomposite films based on macrocyclic compounds (zinc phthalocyanine (ZnPc) and 5,10,15,20-tetra(4-pyridyl) 21H,23H-porphyrin (TPyP)) and metal oxide nanoparticles (ZnO or CuO) were deposited by matrix-assisted pulsed laser evaporation (MAPLE). 1,4-dioxane was used as a solvent in the preparation of MAPLE targets that favor the deposition of films with a low roughness, which is a key feature for their integration in structures for optoelectronic applications. The influence of the addition of ZnO nanoparticles (~20 nm in size) or CuO nanoparticles (~5 nm in size) in the ZnPc:TPyP mixture and the impact of the added metal oxide amount on the properties of the obtained composite films were evaluated in comparison to a reference layer based only on an organic blend. Thus, in the case of nanocomposite films, the vibrational fingerprints of both organic compounds were identified in the infrared spectra, their specific strong absorption bands were observed in the UV–Vis spectra, and a quenching of the TPyP emission band was visible in the photoluminescence spectra. The morphological analysis evidenced agglomerated particles on the composite film surface, but their presence has no significant impact on the roughness of the MAPLE deposited layers. The current density–voltage (J-V) characteristics of the structures based on the nanocomposite films deposited by MAPLE revealed the critical role played by the layer composition and component ratio, an improvement in the electrical parameters values being achieved only for the films with a certain type and optimum amount of metal oxide nanoparticles. [ABSTRACT FROM AUTHOR]

Lately, there is a growing interest in organic photovoltaic (OPV) cells due to the organic materials' properties and compatibility with various types of substrates. However, their efficiencies are low relative to the silicon ones; therefore, other ways (i.e., electrode micron/nanostructuring, synthesis of new organic materials, use of additives) to improve their performances are still being sought. In this context, we studied the behavior of the common organic bulk heterojunction (P3HT:PC70BM) deposited by matrix-assisted pulsed laser evaporation (MAPLE) with/without 0.3% of 1,8-diiodooctane (DIO) additive on flat and micro-patterned ITO substrates. The obtained results showed that in the MAPLE process, a small quantity of additive can modify the morphology of the organic films and decrease their roughness. Besides the use of the additive, the micro-patterning of the electrode leads to a greater increase in the absorption of the studied photovoltaic structures. The inferred values of the filling factors for the measured cells in ambient conditions range from 19% for the photovoltaic structures with no additive and without substrate patterning to 27% for the counterpart structures with patterning and a small quantity of additive. [ABSTRACT FROM AUTHOR]

The discovery of multifunctional properties related to electro-activity of organic systems of biomolecules is important for a variety of applications, especially for devices in the realm of biocompatible sensors and/or bioactuators. A further step towards such applications is to prepare thin films with the required properties. Here, the investigation is focused on the characterization of films of guanine and cytosine nucleobases, prepared by thermal evaporation—an industrial accessible deposition technique. The cytosine films have an orthorhombic non-centrosymmetric structure and grow in two interconnected nanostructured fractal patterns, of nearly equal proportion. Piezoresponse force microscopy images acquired at room temperature on the cytosine films display large zones with antiparallel alignment of the vertical components of the polarization vector. Guanine films have a dense nano-grained morphology. Our studies reveal electrical polarization switching effects which can be related to ferroelectricity in the films of guanine molecules. Characteristic ferroelectric polarization–electric-field hysteresis loops showing large electrical polarization are observed at low temperatures up to 200 K. Above this temperature, the guanine films have a preponderant paraelectric phase containing residual or locally induced nano-scopic ferroelectric domains, as observed by piezoresponse force microscopy at room temperature. [ABSTRACT FROM AUTHOR]

Thick slices mechanically polished cut from a pure benzil ingot grown from melt in a modified Bridgman-Stockbarger configuration were irradiated with Ni ions having a specific energy of 11.4 MeV/u at different fluences. The effect of radiation on the properties of bulk benzil has been investigated. The chemical structure was not substantially affected as shown by infrared spectrum. The changes induced on the disorder degree have been evaluated from the Urbach law and X Ray Diffraction measurements. The morphology and surface topography have been analyzed emphasising a decrease in the size of granules and an increase in the surface roughness by irradiation. No effect of irradiation on the photoluminescence emission and optical nonlinear properties has been evidenced. These results recommend benzil as candidate for applications in space technology. [ABSTRACT FROM AUTHOR]

• The highest disorder in benzil was induced by the organic dopant: m-DNB. • The presence of disorder in benzil crystals do not prevent the SHG. • By doping we can enhance the SHG in benzil crystals. • By doping we can tune the benzil dielectric constant. Single-doped [Ag, Na, iodine, naphthalene (Naph), meta -dintrobenzene (m-DNB)] and double-doped, organic–inorganic (Naph + iodine; m-DNB + iodine) benzil (Bz) crystals have been grown from melt in a Bridgman-Stockbarger configuration. All crystals have been grown in the same experimental conditions, temperature variation at the growth interface = 30 K and moving speed of the growth ampoule = 1 mm/h. These conditions have been estimated from the theoretical analysis involving the solution of the classical (conventional) Stefan problem for flat solid–liquid interface in the boundary conditions imposed by our growth system. The effect of doping on the disorder degree, photoluminescence and dielectric constant of the Bz matrix has been investigated. The disorder in the crystals increased with the increase of dopant concentration. The highest disorder was induced by the organic dopant m-DNB, whose molecules does not show an adequate geometrical similarity with Bz molecules. The position of the photoluminescence peak, both at excitation with 335 nm and 435 nm, has not been affected by the presence of dopant(s). All doped samples show Second Harmonic Generation, even those with a significant degree of disorder. The effect of the single and double-doping on the second-order ONL coefficient was analyzed by comparison with the second-order ONL coefficient of pure Bz crystals. In the case of the double-doping, the highest second-order optical nonlinear coefficient has been evidenced in the Bz crystals simultaneously doped with m-DNB and iodine in the same concentration (1%). [ABSTRACT FROM AUTHOR]

Highlights: [•] We realize multilayer structures by laser deposition (PLD&MAPLE). [•] The bi-layer organic heterostructure (ZnPc/NTCDA) is an injector contact. [•] Oxygen plasma treatment decreases the roughness of AZO films. [•] The crystallinity of AZO layer increases at 10min oxygen plasma treatment. [•] Oxygen plasma treatment of AZO layers improves the electrical properties. [Copyright &y& Elsevier]

We investigated the optical and electrical properties of flexible single and bi-layer organic heterostructures prepared by vacuum evaporation with a p-type layer of arylenevinylene oligomers, based on carbazole, 3,3′ bis(N hexylcarbazole)vinylbenzene = L13, or triphenylamine, 1,4 bis [4 (N,N' diphenylamino)phenylvinyl] benzene = L78, and an n-type layer of 5,10,15,20-tetra(4-pyrydil)21H,23H-porphyne = TPyP. Transparent conductor films of Al-doped ZnO (AZO) with high transparency, >90% for wavelengths > 400 nm, and low resistivity, between 6.9 × 10−4 Ω·cm and 23 × 10−4 Ω·cm, were deposited by pulsed laser deposition on flexible substrates of polyethylene terephthalate (PET). The properties of the heterostructures based on oligomers and zinc phthalocyanine (ZnPc) were compared, emphasizing the effect of the surface morphology. The measurements revealed a good absorption in the visible range of the PET/AZO/arylenevinylene oligomer/TPyP heterostructures and a typical injection contact behavior with linear (ZnPc, L78) or non-linear (L13) J-V characteristics in the dark, at voltages < 0.4 V. The heterostructure PET/AZO/L78/TPyP/Al showed a current density of ~1 mA/cm2 at a voltage of 0.3 V. The correlation between the roughness exponent, evaluated from the height-height correlation function, grain shape, and electrical behavior was analyzed. Consequently, the oligomer based on triphenylamine could be a promising replacement of donor ZnPc in flexible electronic applications. [ABSTRACT FROM AUTHOR]

The properties of organic heterostructures with mixed layers made of arylenevinylene-based polymer donor and non-fullerene perylene diimide acceptor, deposited using Matrix Assisted Pulsed Laser Evaporation on flat Al and nano-patterned Al electrodes, were investigated. The Al layer electrode deposited on the 2D array of cylindrical nanostructures with a periodicity of 1.1 µm, developed in a polymeric layer using UV-Nanoimprint Lithography, is characterized by an inflorescence-like morphology. The effect of the nanostructuring on the optical and electrical properties was studied by comparison with those of the heterostructures based on a mixed layer with fullerene derivative acceptor. The low roughness of the mixed layer deposited on flat Al was associated with high reflectance. The nano-patterning, which was preserved in the mixed layer, determining the light trapping by multiple scattering, correlated with the high roughness and led to lower reflectance. A decrease was also revealed in photoluminescence emission both at UV and Vis excitation of the mixed layer, with the non-fullerene acceptor deposited on nano-patterned Al. An injector contact behavior was highlighted for all Al/mixed layer/ITO heterostructures by I-V characteristics in dark. The current increased, independently of acceptor (fullerene or non-fullerene), in the heterostructures with nano-patterned Al electrodes for shorter conjugation length polymer donors. [ABSTRACT FROM AUTHOR]

Continuing growth in global energy consumption and the growing concerns regarding climate change and environmental pollution are the strongest drivers of renewable energy deployment. Solar energy is the most abundant and cleanest renewable energy source available. Nowadays, photovoltaic technologies can be regarded as viable pathways to provide sustainable energy generation, the achievement attained in designing nanomaterials with tunable properties and the progress made in the production processes having a major impact in their development. Solar cells involving hybrid nanocomposite layers have, lately, received extensive research attention due to the possibility to combine the advantages derived from the properties of both components: flexibility and processability from the organic part and stability and optoelectronics features from the inorganic part. Thus, this review provides a synopsis on hybrid solar cells developed in the last decade which involve composite layers deposited by spin-coating, the most used deposition method, and matrix-assisted pulsed laser evaporation, a relatively new deposition technique. The overview is focused on the hybrid nanocomposite films that can use conducting polymers and metal phthalocyanines as p-type materials, fullerene derivatives and non-fullerene compounds as n-type materials, and semiconductor nanostructures based on metal oxide, chalcogenides, and silicon. A survey regarding the influence of various factors on the hybrid solar cell efficiency is given in order to identify new strategies for enhancing the device performance in the upcoming years. [ABSTRACT FROM AUTHOR]

The matrix-assisted pulsed laser evaporation (MAPLE) technique was used for depositing thin films based on a recently developed conjugated polymer, poly[2,5-(2-octyldodecyl)-3,6-diketopyrrolopyrrole-alt-5,5-(2,5-di(thien-2-yl)thieno [3,2-b]thiophene)] (DPP-DTT) and fullerene C60 blends. The targets used in the MAPLE process were obtained by freezing chloroform solutions with different DPP-DTT:C60 weight ratios, with the MAPLE deposition being carried at a low laser fluence, varying the number of laser pulses. The structural, morphological, optical, and electrical properties of the DPP-DTT:C60 blend layers deposited by MAPLE were investigated in order to emphasize the influence of the DPP-DTT:C60 weight ratio and the number of laser pulses on these features. The preservation of the chemical structure of both DPP-DTT and C60 during the MAPLE deposition process is confirmed by the presence of their vibrational fingerprints in the FTIR spectra of the organic thin films. The UV-VIS and photoluminescence spectra of the obtained organic layers reveal the absorption bands attributed to DPP-DTT and the emission bands associated with C60, respectively. The morphology of the DPP-DTT:C60 blend films consists of aggregates and fibril-like structures. Regardless the DPP-DTT:C60 weight ratio and the number of laser pulses used during the MAPLE process, the current–voltage characteristics recorded, under illumination, of all structures developed on the MAPLE deposited layers evidenced a photovoltaic cell behavior. The results proved that the MAPLE emerges as a viable technique for depositing thin films based on conjugated polymers featured by a complex structure that can be further used to develop devices for applications in the solar cell area. [ABSTRACT FROM AUTHOR]

Matrix-assisted pulsed laser evaporation (MAPLE) was used to deposit hybrid nanocomposite thin films based on cobalt phthalocyanine (CoPc), C60 fullerene and ZnO nanoparticles. The inorganic nanoparticles, with a size of about 20 nm, having the structural and optical properties characteristic of ZnO, were chemically synthesized by a simple precipitation method. Furthermore, ZnO nanoparticles were dispersed in a dimethyl sulfoxide solution in which CoPc and C60 had been dissolved, ready for the freezing MAPLE target. The effect of the concentration of ZnO nanoparticles on the structural, morphological, optical and electrical properties of the CoPc:C60:ZnO hybrid nanocomposite layers deposited by MAPLE was evaluated. The infrared spectra of the hybrid nanocomposite films confirm that the CoPc and C60 preserve their chemical structure during the laser deposition process. The CoPc optical signature is recognized in the ultraviolet–visible (UV–Vis) spectra of the obtained layers, these being dominated by the absorption bands associated to this organic compound while the ZnO optical fingerprint is identified in the photoluminescence spectra of the prepared layers, these disclosing the emission bands linked to this inorganic semiconductor. The hybrid nanocomposite layers exhibit globular morphology, which is typical for the thin films deposited by MAPLE. Current-voltage (J-V) characteristics of the structures developed on CoPc:C60:ZnO layers reveal that the addition of an appropriate amount of ZnO nanoparticles in the CoPc:C60 mixture leads to a more efficient charge transfer between the organic and inorganic components. Due to their photovoltaic effect, structures featuring such hybrid nanocomposite thin films deposited by MAPLE can have potential applications in the field of photovoltaic devices. [ABSTRACT FROM AUTHOR]

In this paper the influence of the heat treatment on the structural and optical properties of oxide single-layer and multilayer transparent thin film structures of ITO/Au/ITO, AZO/Au/AZO, TiO 2 /Au/TiO 2 and Bi 2 O 3 /Au/Bi 2 O 3 type is studied. The single-layer oxides and respective multilayer structures have been deposited on glass substrates by successive DC magnetron sputtering using metallic targets In:Sn, Zn:Al, Ti and Bi, in reactive (for the oxide films) or inert (for the metallic Au interlayer films) atmosphere. Good quality transparent conducting thin film structures have been obtained, with resistivity ∼10 −4 Ω cm and transmittance ∼75%. The wetting surface properties in function of time exposure at UV radiation (254 nm) have been also studied before and after heat treatment performed at 450 °C. [ABSTRACT FROM AUTHOR]

Herein, the properties of the organic heterostructures with triple‐layer ZnO/Ag/ZnO as a replacement for ITO and mixed layer containing arylenevinylene oligomer (based on triphenylamine or carbazole) donor and nonfullerene (perylene diimide) acceptor mixed in the ratio 1:2 and the effect of a buffer layer of PEDOT‐PSS intercalated between triple layer and mixed organic layer are discussed. The UV−vis transmission and photoluminescence (PL) properties are investigated in correlation with the surface topography and reveal a good match between the absorption and emission domain, which can favor the generation of the charge carriers. The heterostructure with the mixed layer based on triphenylamine oligomer shows the widest absorption domain, and the PL spectra of the heterostructures realized with either triphenylamine or carbazole oligomer show peaks corresponding to the radiative decay of the donor and acceptor. The I−V characteristics in the dark indicate a slightly nonlinear behavior and the current is affected by the charge carriers recombination on the defects present in the thick mixed layer deposited by matrix‐assisted pulsed laser evaporation. The effect of the PEDOT‐PSS buffer layer on the electrical properties of the organic heterostructure with ZnO/Ag/ZnO electrode is also investigated. [ABSTRACT FROM AUTHOR]

Abstract: This paper presents investigations on the electrical transport phenomena in perylene and PTCDA emphasising the particularities of the charge carrier injection at the contacts with inorganic semiconductors (Si) and metals (Cu, Al) and the effect of the supplementary organic layer (ZnPc, α-NPD) on the electrical conduction. The I–V characteristics for different delay and integration times, at forward and reverse bias, have evidenced a dominant ohmic behaviour of these SIS and MIS structures at low voltage (<0.1V) and limitations of the current induced by the space charge and trap charge at voltages >1V. An intermediate organic layer (ZnPc) with higher ionisation potential than PTCDA and lower electron affinity than perylene improves the charge carrier injection and the conduction properties of the Si/PTCDA/Si and forward biased Cu/perylene/Si heterostructures. No increase in the hole injection was obtained in Si(p)/perylene/Si(p) heterostructure introducing an α-NPD layer. [Copyright &y& Elsevier]

The chemical modification of the niobium (Nb) surface after irradiation with femtosecond laser pulses was investigated by scanning electron microscopy coupled with energy dispersive spectroscopy, atomic force microscopy, grazing incidence X-ray diffraction, and micro-Raman spectroscopy. The physical-chemical analyses indicated that the laser treatment results in oxidation of the Nb surface, as well as in the formation of Nb hydrides. Remarkably, after the samples' washing in ethanol, a strong Surface-Enhanced Raman Scattering (SERS) signal originating from the toluene residual traces was evidenced. Further, it was observed that the laser irradiated Nb surface is able to provide a SERS enhancement of ∼1.3×103 times for rhodamine 6G solutions. Thus, for the first time it was shown that Nb/Nb oxide surfaces could exhibit SERS functionality, and so one can expect applications in biological/biochemical screening or for sensing of dangerous environmental substances. [ABSTRACT FROM AUTHOR]

In this study, we implemented a high-performance two-terminal memristor device with a metal/insulator/metal (MIM) structure using a solution-derived In-Ga-Zn-Oxide (IGZO)-based nanocomposite as a resistive switching (RS) layer. In order to secure stable memristive switching characteristics, IGZO:N nanocomposites were synthesized through the microwave-assisted nitridation of solution-derived IGZO thin films, and the resulting improvement in synaptic characteristics was systematically evaluated. The microwave-assisted nitridation of solution-derived IGZO films was clearly demonstrated by chemical etching, optical absorption coefficient analysis, and X-ray photoelectron spectroscopy. Two types of memristor devices were prepared using an IGZO or an IGZO:N nanocomposite film as an RS layer. As a result, the IGZO:N memristors showed excellent endurance and resistance distribution in the 103 repeated cycling tests, while the IGZO memristors showed poor characteristics. Furthermore, in terms of electrical synaptic operation, the IGZO:N memristors possessed a highly stable nonvolatile multi-level resistance controllability and yielded better electric pulse-induced conductance modulation in 5 × 102 stimulation pulses. These findings demonstrate that the microwave annealing process is an effective synthesis strategy for the incorporation of chemical species into the nanocomposite framework, and that the microwave-assisted nitridation improves the memristive switching characteristics in the oxide-based RS layer. [ABSTRACT FROM AUTHOR]

A new composite base on reduced graphene oxide (RGO) and poly(5-amino-1-naphthol) (P5A1N) was synthesized by the electrochemical polymerization of 5-amino-1-naphthol (5A1N) in the presence of HClO4 and H4SiW12O40 onto the surface of Au electrode covered with the RGO sheets. The linear dependence of the current densities of the anodic and cathodic peaks with the scan rate of the potential range (0; 0.8) V vs. SCE, reported during electropolymerization of 5A1N, indicates an electron transfer that is controlled by diffusion. A covalent functionalization of the RGO sheets with P5A1N is argued by: (i) the simultaneous disappearance of the IR band at 1584 cm−1 and the appearance of the new IR bands at 812, 976 and 3744 cm−1, and (ii) the appearance of two Raman lines at 738 and 1428 cm−1. An application of the RGO sheets covalently functionalized with P5A1N is demonstrated to support 1,4-phenylene diisothiocyanate (PDITC), a compound used as a cross-linking agent for various biological applications. The chemical adsorption of PDITC onto the RGO sheets covalently functionalized with P5A1N, which involves the appearance of new functional groups of the type thiourea, was proven by Raman scattering and IR spectroscopy. [ABSTRACT FROM AUTHOR]

Thin films of TiN, ZrC, and ZrN were deposited at room temperature on highly polished Ti and Si samples using the pulsed laser deposition technique. Grazing incidence X-ray diffraction investigations showed that films were nanocrystalline, with grain sizes from 5 to 12 nm and under compression. Simulations of X-ray reflectivity curves acquired from the samples indicated that the deposited layers were dense and smooth. Electrochemical tests performed in simulated body fluid showed that the deposited coatings significantly improved the corrosion resistance of Ti samples. The comparative study found out that the best sample was ZrN/Ti, its corrosion current after 32 days immersion in simulated body fluids being half of that measured for the bare Ti sample and in the same time almost unchanged from the initial value. [ABSTRACT FROM AUTHOR]

We report a study on the biocompatibility vs. thickness in the case of titanium nitride (TiN) films synthesized on 410 medical grade stainless steel substrates by pulsed laser deposition. The films were grown in a nitrogen atmosphere, and their in vitro cytotoxicity was assessed according to ISO 10993-5 [1]. Extensive physical-chemical analyses have been carried out on the deposited structures with various thicknesses in order to explain the differences in biological behavior: profilometry, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction and surface energy measurements. XPS revealed the presence of titanium oxynitride beside TiN in amounts that vary with the film thickness. The cytocompatibility of films seems to be influenced by their TiN surface content. The thinner films seem to be more suitable for medical applications, due to the combined high values of bonding strength and superior cytocompatibility. [ABSTRACT FROM AUTHOR]

Composite silk fibroin–poly(3-hydroxybutyric-acid-co-3-hydroxyvaleric-acid) (SF–PHBV) biodegradable coatings were grown by Matrix Assisted Pulsed Laser Evaporation on titanium substrates. Their physico-chemical properties and particularly the degradation behavior in simulated body fluid at 37 °C were studied as first step of applicability in local controlled release for tissue regeneration applications. SF and PHBV, natural biopolymers with excellent biocompatibility, but different biodegradability and tensile strength properties, were combined in a composite to improve their properties as coatings for biomedical uses. FTIR analyses showed the stoichiometric transfer from targets to coatings by the presence in the spectra of the main absorption maxima characteristic of both polymers. XRD investigations confirmed the FTIR results showing differences in crystallization behavior with respect to the SF and PHBV content. Contact angle values obtained through wettability measurements indicated the MAPLE deposited coatings were highly hydrophilic; surfaces turning hydrophobic with the increase of the PHBV component. Degradation assays proved that higher PHBV contents resulted in enhanced resistance and a slower degradation rate of composite coatings in SBF. Distinct drug-release schemes could be obtained by adjusting the SF:PHBV ratio to controllably tuning the coatings degradation rate, from rapid-release formulas, where SF predominates, to prolonged sustained ones, for larger PHBV content. [ABSTRACT FROM AUTHOR]

Abstract: Cotton fabrics were coated with arrays of ZnO hexagonal prisms using an electroless (catalytic/autocatalytic) deposition process. A typical three step method, similar to those used for electroless deposition of metals on insulating substrates, consisting of pre-activation, activation and deposition steps was employed. The low-dimensional ZnO particles were grown from an aqueous solution containing zinc nitrate as source of zinc ions and dimethylamineborane as reducing agent. The as-obtained ZnO-coated cotton fabrics were characterized from the point of view of structure by X-ray diffraction (XRD) and morphology by scanning electron microscopy (SEM). The XRD studies demonstrate that the ZnO particles have a hexagonal wurtzite crystalline structure. The SEM observations prove that the cotton fibers are homogeneously covered by hexagonal prisms which have uniform base size of approximately 500 nm and height of 1 μm. Optical spectroscopy measurements show that the functionalization with ZnO strongly decreases the transmittance in the UV–vis region of the cotton fabrics. An important characteristic is that the ZnO-functionalized cotton fabrics exhibit superhydrophobicity, with water contact angles exceeding 150°. The technique described is highly reproducible, easy scalable and cheap, allowing a wide range of applications. [Copyright &y& Elsevier]

Abstract: In this paper we present some comparative studies between the optical and electrical properties of the films prepared by vacuum evaporation from amidic monomeric compounds obtained from maleic anhydride and aniline derivative with different functional groups [CN; NO2], and the composite films prepared by spin-coating from a polycarbonate of bisphenol A matrix embedding clusters of these amidic monomers. We have emphasised the effect of the polymeric matrix on the properties of the synthesised monomers with the purpose to change the physical properties of the films (optical transmission, luminescence, electrical conduction, optical non-linear phenomena). The correlation between the morphology of the films and the optical and electrical properties has also been investigated. [Copyright &y& Elsevier]

Abstract: This paper presents a study of some functionalised copolymers thin films prepared on silicon and quartz substrates by matrix assisted pulsed laser evaporation (MAPLE) method. Two polymeric structures have been synthesised by the copolymerisation of maleic anhydride and methyl methacrylate, respectively, maleic anhydride and vinyl benzyl chloride and their subsequent functionalisation with 2,4-dinitroaniline. UV–Vis, FTIR, Raman and photoluminescence spectroscopy have been used to investigate the influence on the properties of the films of different substrate temperature (150°C and 250°C), background N2 pressure (5–30Pa) and polymer concentration in target (2% and 3%). We have evidenced that this deposition process does not damage the chemical structure of the polymers. SEM investigations revealed the droplets type morphology of the polymeric films with thickness between 41nm and 105nm calculated from ellipsometric measurements. [Copyright &y& Elsevier]

This study presents the design and manufacture of metasurface lenses optimized for focusing light with 1.55 µm wavelength. The lenses are fabricated on silicon substrates using electron beam lithography, ultraviolet-nanoimprint lithography and cryogenic deep reactive-ion etching techniques. The designed metasurface makes use of the geometrical phase principle and consists of rectangular pillars with target dimensions of height h = 1200 nm, width w = 230 nm, length l = 354 nm and periodicity p = 835 nm. The simulated efficiency of the lens is 60%, while the master lenses obtained by using electron beam lithography are found to have an efficiency of 45%. The lenses subsequently fabricated via nanoimprint are characterized by an efficiency of 6%; the low efficiency is mainly attributed to the rounding of the rectangular nanostructures during the pattern transfer processes from the resist to silicon due to the presence of a thicker residual layer. [ABSTRACT FROM AUTHOR]

The development of organic—inorganic hybrids or nanocomposite films is increasingly becoming attractive in light of their emerging applications. This research focuses on the formation of a unique nanocomposite film with enhanced elasticity suitable for many biomedical applications. The physical property measurement system and transmission electron microscopy were used to analyze Pt–Fe3O4 hybrid nanoparticles. These nanohybrids exhibited magnetic effects. They were further exploited to prepare the nanocomposite films in conjunction with a chitosan-g–glycolic acid organic fraction. The nanocomposite films were then examined using standard techniques: thermogravimetric analysis, X-ray diffraction, Fourier transform infrared spectroscopy, and atomic force microscopy. Tensile strength testing demonstrated a significantly greater elastic strength of these nanocomposite films than pure chitosan films. The water absorption behavior of the nanocomposites was evaluated by measuring swelling degree. These nanocomposites were observed to have substantially improved physical properties. Such novel nanocomposites can be extended to various biomedical applications, which include drug delivery and tissue engineering. [ABSTRACT FROM AUTHOR]

Nanocomposites comprising high-density polyethylene (HDPE) and boehmite (BA) nanoparticles were prepared by melt blending and subsequently irradiated with electrons. Electron irradiation of HDPE causes crosslinking and, in the presence of BA, generates ketone functional groups. The functional groups can then form hydrogen bonds with the hydroxyl groups on the surface of the BA. Additionally, if the BA is surface modified by vinyltrimethoxysilane (vBA), it can covalently bond with the HDPE by irradiation-induced radical grafting. The strong covalent bonds generated by electron beam irradiation allow the desirable properties of the nanofiller to be transferred to the rest of the nanocomposite. Since EB irradiation produces a great number of strong covalent bonds between vBA nanoparticles and HDPE, the modulus of elasticity, yield strength, and resistance to thermal shrinkage are enhanced by electron irradiation. [ABSTRACT FROM AUTHOR]

This paper fabricates a carbon nanotube (CNT) film-reinforced mesophase pitch-based carbon (CNTF/MPC) nanocomposite by using a hot-pressing carbonization method. During the carbonization, the stacked aromatic layers tended to rearrange into amorphous carbon, and subsequently generated crystalline carbon in the matrix. The continuous entangled CNT networks were efficiently densified by the carbon matrix though optimized external pressure to obtain the high-performance nanocomposites. The CNTF/MPC@1300 displayed a stable electrical conductivity up to 841 S/cm at RT-150 °C. Its thermal conductivity in the thickness direction was 1.89 W/m∙K, an order of magnitude higher than that of CNT film. Moreover, CNTF/MPC@1300 showed a mass retention of 99.3% at 1000 °C. Its tensile strength was 2.6 times the CNT film and the tensile modulus was two orders of magnitude higher. Though the CNTF/MPC nanocomposites exhibited brittle tensile failure mode, they resisted cyclic bending without damage. The results demonstrate that the CNTF/MPC nanocomposite has potential application in multi-functional temperature resistance aerospace structures. [ABSTRACT FROM AUTHOR]

In this work, we performed a systematic study of the physical properties of amorphous Indium–Gallium–Zinc Oxide (a-IGZO) films prepared under various deposition pressures, O 2 /(Ar+O 2 ) flow ratios, and annealing temperatures. X-ray reflectivity (XRR) and microwave photoconductivity decay (μ -PCD) measurements were conducted to evaluate the quality of a-IGZO films. The results showed that the process conditions have a substantial impact on the film densities and defect states, which in turn affect the performance of the final thin-film transistors (TFT) device. By optimizing the IGZO film deposition conditions, high-performance TFT was able to be demonstrated, with a saturation mobility of 8.4 cm 2 /Vs, a threshold voltage of 0.9 V, and a subthreshold swing of 0.16 V/dec. [ABSTRACT FROM AUTHOR]

The influence of Ag and Au nanoparticles and reduced graphene oxide (RGO) sheets on the photodegradation of α-lipoic acid (ALA) was determined by UV-VIS spectroscopy. The ALA photodegradation was explained by considering the affinity of thiol groups for the metallic nanoparticles synthesized in the presence of trisodium citrate. The presence of excipients did not induce further changes when ALA interacts with Ag and Au nanoparticles with sizes of 5 and 10 nm by exposure to UV light. Compared to the Raman spectrum of ALA powder, changes in Raman lines' position and relative intensities when ALA has interacted with films obtained from Au nanoparticles with sizes between 5 and 50 nm were significant. These changes were explained by considering the chemical mechanism of surface-enhanced Raman scattering (SERS) spectroscopy. The photodegradation of ALA that had interacted with metallic nanoparticles was inhibited in the presence of RGO sheets. [ABSTRACT FROM AUTHOR]

Our study focused on the long-term degradation under simulated conditions of coatings based on different compositions of polycaprolactone-polyethylene glycol blends (PCL-blend-PEG), fabricated for titanium implants by a dip-coating technique. The degradation behavior of polymeric coatings was evaluated by polymer mass loss measurements of the PCL-blend-PEG during immersion in SBF up to 16 weeks and correlated with those yielded from electrochemical experiments. The results are thoroughly supported by extensive compositional and surface analyses (FTIR, GIXRD, SEM, and wettability investigations). We found that the degradation behavior of PCL-blend-PEG coatings is governed by the properties of the main polymer constituents: the PEG solubilizes fast, immediately after the immersion, while the PCL degrades slowly over the whole period of time. Furthermore, the results evidence that the alteration of blend coatings is strongly enhanced by the increase in PEG content. The biological assessment unveiled the beneficial influence of PCL-blend-PEG coatings for the adhesion and spreading of both human-derived mesenchymal stem cells and endothelial cells. [ABSTRACT FROM AUTHOR]

Composite thin coatings of conductive polymer (polyaniline grafted lignin, PANI-LIG) embedded with aminoglycoside Gentamicin sulfate (GS) or magnetite nanoparticles loaded with GS (Fe3O4@GS) were deposited by the matrix-assisted pulsed laser evaporation (MAPLE) technique. The aim was to obtain such nanostructured coatings for titanium-based biomedical surfaces, which would induce multi-functional properties to implantable devices, such as the controlled release of the therapeutically active substance under the action of a magnetic and/or electric field. Thus, the unaltered laser transfer of the initial biomaterials was reported, and the deposited thin coatings exhibited an appropriate nanostructured surface, suitable for bone-related applications. The laser processing of PANI-LIG materials had a meaningful impact on the composites' wettability, since the contact angle values corresponding to the composite laser processed materials decreased in comparison with pristine conductive polymer coatings, indicating more hydrophilic surfaces. The corrosion resistant structures exhibited significant antimicrobial activity against Escherichia coli, Staphylococcus aureus, and Candida albicans strains. In vitro cytotoxicity studies demonstrated that the PANI-LIG-modified titanium substrates can allow growth of bone-like cells. These results encourage further assessment of this type of biomaterial for their application in controlled drug release at implantation sites by external activation. [ABSTRACT FROM AUTHOR]