Search

The Asia Pacific Metrology Program (APMP) and the Asia Pacific Laboratory Accreditation Cooperation (APLAC) joint Proficiency Testing (PT) programs for toxic elements such as cadmium (Cd) and lead (Pb) or nutritional elements such as iron (Fe) and zinc (Zn) in food were organized by the Korea Research Institute of Standards and Science (KRISS) with the aim of enhancing the quality of measurement and metrological traceability in various economies of the Asia Pacific region by evaluating the performance with rigorous evaluation. Three APMP-APLAC joint PT programs for elemental analyses were carried out by KRISS sequentially, where candidate certified reference materials (CRMs) were used as the PT materials and metrologically traceable certified reference values (RVs) were used as the PT assigned values for the evaluation of participants' results, which allows reliable evaluation of participant performance. This article describes the operation of the PTs and the overall performance of the participating laboratories. The effectiveness of these joint PT programs and trends in PT performance assessment are also discussed. These PT programs confirm the significant importance of using the metrologically traceable RVs instead of the consensus values from participants as the PT assigned value for reliable assessment. The lack of understanding of the concept of coverage factor, degree of freedom, standard uncertainty, and expanded uncertainty was revealed by some participants in these PT programs. Interpreting the zeta-scores or E

The Asia Pacific Metrology Program (APMP) and Asia Pacific Laboratory Accreditation Cooperation (APLAC) joint proficiency testing (PT) program was established to improve the ability of quantitative analysis and enhance the quality of the PT program through a better regional linkage between the national metrology institutes (NMIs) and the accreditation bodies (ABs) in the Asia-Pacific region. The first APMP-APLAC joint PT was carried out to quantify hazardous elements Cd and Pb in kimchi cabbage powder, where a candidate certified reference material (CRM) was used as the PT material. A total of 83 laboratories from 37 countries registered, of which 73 laboratories submitted their results. Certified reference values (RVs) provided by Korea Research Institute of Standards and Science (KRISS) were used to evaluate the z -scores ( z ) of participants' results. This program confirms significant importance of the use of metrologically traceable RVs as PT assigned values for rigorous evaluation and reliable assessment.

Accurate measurement of hazardous elements in cosmetics is considerably important in response to cosmetic safety issues. A sample preparation method using microwave-assisted acid digestion combined with double isotope dilution inductively coupled plasma/mass spectrometry (ID ICP-MS) was used for the certification of the hazardous elements, Cd, Hg and Pb, in cosmetic powder samples. The HF-free sample preparation method was validated and applied to analyse Cd and Pb in cosmetic powder. The Hg content in the sample was determined by employing a fast valve sample introduction system to resolve the severe memory effect in Hg analysis. Homogeneity and stability were also evaluated. The certified values of Cd, Hg and Pb were (24.8 ± 1.3) mg kg−1, (0.648 ± 0.065) mg kg−1 and (24.55 ± 0.31) mg kg−1, respectively. The relative combined standard uncertainty was 2.7% for Cd, 5.1% for Hg and 0.62% for Pb. The detailed procedure for certification and evaluation of the associated uncertainty is also presented. The proper use of the developed CRM for quality control and method validation in testing laboratories and the cosmetic industry is expected to significantly improve the reliability and quality of test results for hazardous elements in cosmetics, thereby contributing to cosmetic safety.

An element-based reductive approach provides an effective means of realizing International System of Units (SI) traceability for high-purity biological standards. Here, we develop an absolute protein quantification method using double isotope dilution (ID) inductively coupled plasma mass spectrometry (ICP-MS) combined with microwave-assisted acid digestion for the first time. We validated the method and applied it to certify the candidate protein certified reference material (CRM) of human growth hormone (hGH). The concentration of hGH was determined by analysing the total amount of sulfur in hGH. Next, the size-exclusion chromatography method was used with ICP-MS to characterize and quantify sulfur-containing impurities. By subtracting the contribution of sulfur-containing impurities from the total sulfur content in the hGH CRM, we obtained a SI-traceable certification value. The quantification result obtained with the present method based on sulfur analysis was in excellent agreement with the result determined via a well-established protein quantification method based on amino acid analysis using conventional acid hydrolysis combined with an ID liquid chromatography-tandem mass spectrometry. The element-based protein quantification method developed here can be generally used for SI-traceable absolute quantification of proteins, especially pure-protein standards.

The competitive adsorption of fibrinogen (FB) and DPPC at the air/aqueous interface, in phosphate buffer saline at 25 degrees C, was studied with tensiometry, infrared reflection absorption spectroscopy (IRRAS), and ellipsometry. For FB/DPPC mixtures with 750 ppm (0.075 wt%) FB and 1000 ppm (0.10 wt%) DPPC, the tension behavior was found to be similar to that of FB when alone, even with DPPC and FB being at the interface. Thus, FB interferes with adsorption of DPPC and inhibits its surface tension lowering ability. When FB protein is introduced in the solution after a DPPC monolayer has formed, the adsorption of FB is inhibited by the DPPC monolayer. When a DPPC monolayer is spread onto a solution with a preadsorbed FB layer, the DPPC monolayer excludes FB from the surface and controls the tension behavior with little inhibition by FB. When a DPPC dispersion is introduced with the Trurnit method, or sprayed dropwise, onto an aqueous FB/DPPC surfaces, the DPPC layer formed on the surface prevents the adsorption of FB and dominates the surface tension behavior. These results have implications in controlling the inhibition of lung surfactant tension behavior by serum proteins, when they leak at the alveolar lining layer, and in developing surfactant replacement therapies for alveolar respiratory diseases.

In this work, we have prepared bioartificial polymer blends using hyaluronate (HA) as a biological component and poly(vinyl alcohol)–borax association (PVAs) as a synthetic component, and investigated the rheological properties as well as morphology of the blends. When plotted against the blend composition, the rheological properties showed both positive and negative deviation from the linear additive mixing rule depending on thermal history. The blend showed enhanced viscosity at the composition of 20 wt% of HA and 80 wt% of PVAs, when PVA was dissolved at high temperature. The viscosity enhancement was caused by the network formation of HA aggregates in the micrometer scale. In addition, the network structure of HA aggregates was found to be fractal with the fractal dimension of 1.7. As PVA system also forms a network structure in the nanometer scale between hydroxyl groups of PVA and borate anions, the blend system is unique in that it has network structures in both micrometer and nanometer scales in one material. On the contrary, HA formed aggregates but not any network structure in the blend of the same composition but of the negative deviation. In conclusion, we showed that HA/PVAs blend system may have diverse morphology as well as very broad spectrum of rheological properties, and could suggest that the rheology and morphology of HA/PVAs blends can be designed not only by controlling composition but also by controlling thermal and deformation history of the components.

Rheological properties of some polymer solutions in both the linear and non-linear regions have been investigated. The solutions include poly(vinyl alcohol) solution (with and without sodium borate), hyaluronic acid solution, and xanthan gum solution; some of which form microstructures depending on their deformation history, and thus can be classed as complex fluids. Among the rheological properties, the large amplitude oscillatory shear (LAOS) behavior was found to be very sensitive to the interactions or the shear-induced formation of microstructures. Depending on the interactions between the microstructures, it was found that there exist at least four types of LAOS behavior: type I, strain thinning (G′, G″ decreasing); type II, strain hardening (G′, G″ increasing); type III, weak strain overshoot (G′ decreasing, G″ increasing followed by decreasing); type IV, strong strain overshoot (G′, G″ increasing followed by decreasing). It is suggested that the LAOS behavior can be effectively used as a tool for classifying the complex fluids.

The effect of the buffer composition and the preparation protocol on the dynamic surface tension (DST) and vesicle sizes of aqueous dipalmitoylphosphatidylcholine (DPPC) dispersions was studied. Four isotonic buffers were used in preparing DPPC dispersions at physiological conditions for possible biological applications: (1) a standard PBS solution; (2) the above PBS with 1mM CaCl(2); (3) PBS with one tenth the previous standard phosphate salt concentrations and 2.5 mM CaCl(2); and (4) 150 mM NaCl with 2.5 mM CaCl(2) and 10mM HEPES (4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid). Two protocols, with a new method and an old method (Bangham method), were used in preparing the DPPC dispersions. The DPPC dispersions prepared with the new method contained mostly vesicles and were quite stable at 25 or 37 degrees C. Dynamic light scattering (DLS) and spectroturbidimetry (ST) results showed that the DPPC vesicle sizes in buffer (4) were much smaller than those in the other buffers. When the DPPC dispersions were prepared with the new method, the diameter of the DPPC particles was smaller than those with the old method. The DPPC vesicles with the new method were more stable than those with the other method. The DPPC dispersions of 1000 ppm at 37 degrees C with the new method produced, at pulsating area conditions at 20 cycles per minute, low tension minima (gamma(min)), lower than 10 mN/m, in buffers (1), (2), and (4). With buffer (4) the DSTs were lower and were achieved faster than with the other buffers. A minimum concentration of 1000 or 250 ppm DPPC was needed to produce DSTs lower than 10 mN/m within 10 min or less, with buffer (2) or (4), respectively. IRRAS results suggest that DPPC in buffer (2) or (4) forms a close-packed monolayer at the interface. These results have implications for designing efficient protocols of lipid dispersion preparation and lung surfactant replacement formulations in treating respiratory disease.

The stability and state of aggregation of aqueous fibrinogen (FB) and dipalmitoylphosphatidylcholine (DPPC) vesicles in water or buffer at 25 degrees C were studied with dynamic light scattering (DLS), UV-vis spectroturbidimetry (ST), and cryo-transmission electron microscopy (cryo-TEM). In water, when 1000 ppm (0.10 wt %) DPPC dispersions were prepared with a protocol including extensive sonication, they contained mostly vesicles and were quite clear, transparent, and stable for at least 30 days. FB mixtures with water (0.075 wt %) were quite unstable and biphasic. They formed large aggregates which eventually precipitated. The addition of DPPC vesicles into these unstable FB dispersions reversed FB aggregation and precipitation and produced stable translucent microdispersions. The inferred lipid/protein aggregates were limited in size, with average diameters ranging from 200 to 300 nm. In buffer, DPPC dispersions were also clear and quite stable, with average dispersed particles diameter of ca. 90 nm. FB dissolved in aqueous buffer and formed transparent and stable solutions. Adding salt to an aggregated FB dispersion in water reversed the aggregation. FB aggregated and redissolved in the presence of the citrate and after the citrate was removed. There was no effect of citrate (present in FB initially) in the FB aggregation or redissolution. FB molecules in buffer form dimers or higher aggregates. Their average aggregation number is 2, determined with Rayleigh scattering analysis of turbidity data. The average hydrodynamic diameter of FB solutions from DLS was 30 nm. Mixing a stable FB solution in buffer and a stable DPPC dispersion in buffer produced highly unstable mixtures, in which large aggregates precipitated. These results have implications in understanding the interactions of lipids and proteins in many biological applications and food processing applications.

The effect of sonication and freezing-thawing on the aggregate size and dynamic surface tension of aqueous dipalmitoylphosphatidylcholine (DPPC) dispersions was studied by cryogenic-transmission electron microscopy (cryo-TEM), dynamic light scattering (DLS), UV-vis spectroturbidimetry, and surface tensiometry. When 1000 ppm (0.1 wt%) DPPC dispersions were prepared with a certain protocol, including extensive sonication, they contained mostly frozen vesicles and were quite clear, transparent, and stable for at least 30 days. The average dispersed vesicles diameter was 80 nm in water and 90 nm in standard phosphate saline buffer. After a freeze-thaw cycle, this dispersion became turbid, and precipitates of coagulated vesicles were observed with large particles of average size of 1.5x10(3) nm. The vesicle coagulation is due to the local salt concentration increase during the freezing of water. This dispersion has much higher equilibrium and dynamic surface tension than those before freezing. When this freeze-thawed dispersion was subjected to a resonication at 55 degrees C, smaller vesicles with sizes of ca. 70 nm were produced, and a lower surface tension behavior was restored as before freezing. Similar behavior was observed at 30 ppm DPPC. These results indicate that the freeze-thaw cycle causes substantial aggregation and precipitation of the vesicles. These results have implications for designing efficient protocols of lipid dispersion preparation and lung surfactant replacement formulations in treating respiratory disease and for effective administration.

The adsorption behavior of dipalmitoylphosphatidylcholine (DPPC), which is the major component of lung surfactant, at the air/aqueous interface and the competitive adsorption with bovine serum albumin (BSA) were studied with tensiometry, infrared reflection absorption spectroscopy (IRRAS), and ellipsometry. Dynamic surface tensions lower than 1 mN/m were observed for DPPC dispersions, with mostly vesicles, prepared with new protocols, involving extensive sonication above 50 degrees C. The lipid adsorbs faster and more extensively for DPPC dispersions with vesicles than with liposomes. For DPPC dispersions by a certain preparation procedure at T>T(c), when lipid particles were observed on the surface, dynamic surface tensions as low as 1 mN/m were measured. Moreover, IRRAS intensities and ellipsometric deltaDelta values were found to be much higher than the values for other DPPC dispersions or spread DPPC monolayers, suggesting that a larger amount of liposomes or vesicles adsorb on the surface. For DPPC/BSA mixtures, the tension behavior is controlled primarily by BSA, which prevents the formation of a dense DPPC monolayer. When BSA is injected into the subphase with a spread DPPC monolayer or into a DPPC dispersion with preadsorbed layers, little or no BSA adsorbs and the DPPC layer remains on the surface. When a DPPC monolayer is spread on a BSA solution at 0.1 wt% at 25 degrees C, then DPPC lipid can displace the adsorbed BSA molecules. The lack of BSA adsorption, and the expulsion of BSA by DPPC monolayer is probably due to the strong hydrophilicity of the lipid polar headgroup. When a DPPC dispersion is introduced with Trurnit's method or when dispersion drops are sprayed onto the surface of a DPPC/BSA mixture, the surface tension becomes lower and is controlled by DPPC, which can prevent the adsorption of BSA. The results may be important in understanding inhibition of lung surfactants by serum proteins and in designing efficient protocols of surfactant preparation and administration.

Cosmetics are used in practically all walks of life as a means of improving skin and beautifying complexion. In recent years, more and more attention has been paid to the cosmetic safety. In response to the cosmetic safety issue, the accurate measurement of the heavy metals in cosmetics is, therefore, particularly important. NMIs from different countries should establish their chemical metrology traceability system in this area, which includes both measurement methods research and certain CRMs development. It should be noted that because the matrix of many cosmetics is complex and the contents of the heavy metals are relatively low, it still is a challenging task to measure the analytes with high accuracy and precision. CCQM-K106 followed up CCQM pilot study 'CCQM-P128: Pb, As measurements in cosmetic (cream)' coordinated by the National Institute of Metrology, China (NIM) in 2009. The cream was selected as the testing material, which is widely used as a daily skin care worldwide. This is the first CCQM key comparison regarding the measurement of toxic metal elements with the cosmetic matrix, which includes pure water, liquid paraffin, silicone oil, synthetic squalane, hyaluronic acid, glycerin, propylene glycol, allantoin, preservative and so on. The aim of the CCQM-K106 is to demonstrate the capability of participating NMIs and designated institutes in measuring the contents of poisonous elements, including lead, arsenic and mercury in a cosmetic sample (cream), and support CMC claims relating to inorganic elements in cosmetic materials and similar chemical industry products. The cream matrix sample was prepared under the guidance of professional technicians. The formula of the cream was carefully chosen to match with a real cosmetic. The homogeneity and stability level of Pb, As and Hg in the cream sample were fit for the objective of the comparison. Each participant received two numbered bottles containing about 5g samples in each bottle. The instruction relating to CCQM-K106 was sent to each participant by e-mail, which consisted of technical protocol, results report form and inorganic core capabilities tables. The results were reported as mass faction (mg/kg). Calculation of the uncertainty expressed as a combined standard uncertainty and an expanded uncertainty at 95% confidence. In order to allow a sufficient evaluation of the comparison, the report was required to include a detailed description of the applied method of measurement, information about sample digestion and preparation, information about the reference material used for calibration. The methods of measurement were free to be selected by the participants. For the sample treatment, most of the participants used microwave digestion method. For instrumental determination, a variety of techniques such as ICP-MS, AAS, INAA were adopted by the participants. Most participants choose ID-ICP-MS method to measure Pb and Hg, which showed the better performance in terms of consistency and reliability of the measurement results. The reference mass fraction values and associated uncertainties were calculated by different statistic ways. As the result, the median and uncertainty of median were proposed as the key comparison reference value (KCRV) and its associated key comparison reference uncertainty after removal of suspected extreme values. In general, the performances of the majority of the CCQM-K106 participants are excellent, illustrating their measurement capability for Pb, As and Hg in a complex greasy matrix. The results can be used further by any participant to support its CMC claim at least for a borate buffer. That claim will concern the pH method employed by the participant during this comparison and will cover the used temperature(s) or the full temperature range between 15?C and 37 ?C for the participant which measured pH values at the three temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).