Search

Electromagnetic (EM) wave detection over a large spectrum has recently attracted significant amount of attention. Traditional electronic EM wave sensors use large metallic probes which distort the field to be measured and also have strict limitations on the detectable RF bandwidth. To address these problems, integrated photonic EM wave sensors have been developed to provide high sensitivity and broad bandwidth. Previously we demonstrated a compact, broadband, and sensitive integrated photonic EM wave sensor, consisting of an organic electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW) modulator integrated with a gold bowtie antenna, to detect the X band of the electromagnetic spectrum. However, due to the relative large RC constant of the silicon PCW, such EM wave sensors can only work up to tens of GHz. In this work, we present a detailed design and discussion of a new generation of EM wave sensors based on EO polymer refilled plasmonic slot waveguides in conjunction with bowtie antennas to cover a wider electromagnetic spectrum from 1 GHz up to 10THz, including the range of microwave, millimeter wave and even terahertz waves. This antenna-coupled plasmonic-organic hybrid (POH) structure is designed to provide an ultra-small RC constant, a large overlap between plasmonic mode and RF field, and strong electric field enhancement, as well as negligible field perturbation. A taper is designed to bridge silicon strip waveguide to plasmonic slot waveguide. Simulation results show that our device can have an EM wave sensing ability up to 10 THz. To the best of our knowledge, this is the first POH device for photonic terahertz wave detection., Comment: 8 pages, 6 figures, SPIE Photonics West 2016, Paper No. 975614-975614-975618. arXiv admin note: text overlap with arXiv:1503.01904

The bowtie antenna is a topic of growing interest in recent years. In this paper, we design, fabricate, and characterize a modified gold bowtie antenna integrated on a transparent silica substrate. The bowtie antenna is designed with broad RF bandwidth to cover the X-band in the electromagnetic spectrum. We numerically investigate the antenna characteristics, specifically its resonant frequency and enhancement factor. Our designed bowtie antenna provides a strong broadband electric field enhancement in its feed gap. Taking advantage of the low-k silica substrate, high enhancement factor can be achieved without the unwanted reflection and scattering from the backside silicon handle which is the issue of using an SOI substrate. We simulate the dependence of resonance frequency on bowtie geometry, and verify the simulation results through experimental investigation, by fabricating different sets of bowtie antennas on silica substrates and then measuring their resonance frequencies. In addition, the far-field radiation pattern of the bowtie antenna is measured, and it shows dipole-like characteristics with large beam width. Such a broadband antenna will be useful for a myriad of applications, ranging from photonic electromagnetic wave sensing to wireless communications., Comment: arXiv admin note: substantial text overlap with arXiv:1503.01907

In this paper, we design a dielectric-to-plasmonic slot waveguide mode converter based on the hybrid silicon-gold taper. The effects of mode matching, the effective index matching, and the metallic absorption loss on the conversion efficiency are studied. Consequently, a metallic taper-funnel coupler with an overall length of 1.7um is designed to achieve a very high conversion efficiency of 93.3% at 1550 nm. The configuration limitations for not allowing this mode converter to achieve a 100% conversion efficiency are also investigated. Such a high-efficiency converter can provide practical routes to realize ultracompact integrated circuits., Comment: 6 pages, 7 figures

The bowtie antenna is a topic of growing interest in recent years. In this paper, we design, fabricate, and characterize a modified gold bowtie antenna integrated on a transparent glass substrate. We numerically investigate the antenna characteristics, specifically its resonant frequency and enhancement factor. We simulate the dependence of resonance frequency on bowtie geometry, and verify the simulation results through experimental investigation, by fabricating different sets of bowtie antennas on glass substrates utilizing CMOS compatible processes and measuring their resonance frequencies. Our designed bowtie antenna provides a strong broadband electric field enhancement in its feed gap. The far-field radiation pattern of the bowtie antenna is measured, and it shows dipole-like characteristics with large beam width. Such a broadband antenna will be useful for a myriad of applications, ranging from wireless communications to electromagnetic wave detection., Comment: 8 pages, 7 figures, SPIE Photonics West Conference

Silicon-organic hybrid integrated devices have emerging applications ranging from high-speed optical interconnects to photonic electromagnetic-field sensors. Silicon slot photonic crystal waveguides (PCWs) filled with electro-optic (EO) polymers combine the slow-light effect in PCWs with the high polarizability of EO polymers, which promises the realization of high-performance optical modulators. In this paper, a broadband, power-efficient, low-dispersion, and compact optical modulator based on an EO polymer filled silicon slot PCW is presented. A small voltage-length product of V{\pi}*L=0.282Vmm is achieved, corresponding to an unprecedented record-high effective in-device EO coefficient (r33) of 1230pm/V. Assisted by a backside gate voltage, the modulation response up to 50GHz is observed, with a 3-dB bandwidth of 15GHz, and the estimated energy consumption is 94.4fJ/bit at 10Gbit/s. Furthermore, lattice-shifted PCWs are utilized to enhance the optical bandwidth by a factor of ~10X over other modulators based on non-band-engineered PCWs and ring-resonators., Comment: 12 pages, 4 figures, SPIE Photonics West Conference 2015

We design, fabricate and experimentally demonstrate a highly efficient adiabatic mode converter for coupling light into a silicon slot waveguide with a slot width as large as 320nm. This strip-to-slot mode converter is optimized to provide a measured insertion loss as low as 0.08dB. Our mode converter provides 0.1dB lower loss compared to a conventional V-shape mode converter. This mode converter is used to couple light into and out of a 320nm slot photonic crystal waveguide, and it is experimentally shown to improve the coupling efficiency up to 3.5dB compared to the V-shape mode converter, over the slow-light wavelength region., Comment: 13 pages, 7 figures, SPIE Photonics West Conference 2014

In this work, we design, fabricate and characterize a compact, broadband and highly sensitive integrated photonic electromagnetic field sensor based on a silicon-organic hybrid modulator driven by a bowtie antenna. The large electro-optic (EO) coefficient of organic polymer, the slow-light effects in the silicon slot photonic crystal waveguide (PCW), and the broadband field enhancement provided by the bowtie antenna, are all combined to enhance the interaction of microwaves and optical waves, enabling a high EO modulation efficiency and thus a high sensitivity. The modulator is experimentally demonstrated with a record-high effective in-device EO modulation efficiency of r33=1230pm/V. Modulation response up to 40GHz is measured, with a 3-dB bandwidth of 11GHz. The slot PCW has an interaction length of 300um, and the bowtie antenna has an area smaller than 1cm2. The bowtie antenna in the device is experimentally demonstrated to have a broadband characteristics with a central resonance frequency of 10GHz, as well as a large beam width which enables the detection of electromagnetic waves from a large range of incident angles. The sensor is experimentally demonstrated with a minimum detectable electromagnetic power density of 8.4mW/m2 at 8.4GHz, corresponding to a minimum detectable electric field of 2.5V/m and an ultra-high sensitivity of 0.000027V/m Hz^-1/2 ever demonstrated. To the best of our knowledge, this is the first silicon-organic hybrid device and also the first PCW device used for the photonic detection of electromagnetic waves. Finally, we propose some future work, including a Teraherz wave sensor based on antenna-coupled electro-optic polymer filled plasmonic slot waveguide, as well as a fully packaged and tailgated device., Comment: 20 pages, 16 figures

We design, fabricate and experimentally demonstrate a highly efficient adiabatic mode converter for coupling light into a silicon slot waveguide with a slot width as large as 320nm. This strip-to-slot mode converter is optimized to provide a measured insertion loss as low as 0.08dB. Our mode converter provides 0.1dB lower loss compared to a conventional V-shape mode converter. This mode converter is used to couple light into and out of a 320nm slot photonic crystal waveguide, and it is experimentally shown to improve the coupling efficiency up to 3.5dB compared to the V-shape mode converter, over the slow-light wavelength region., Comment: 13 pages, 7 figures

The accelerating increase in information traffic demands the expansion of optical access network systems that require cost reduction of optical and photonic components. Low cost, ease of fabrication, and integration capabilities of low optical-loss polymers make them attractive for photonic applications. In addition to passive wave-guiding components, electro-optic (EO) polymers consisting of a polymeric matrix doped with organic nonlinear chromophores have enabled wide-RF-bandwidth and low-power optical modulators. Beside board level passive and active optical components, compact on-chip modulators (a few 100 micronmeters to a few millimeters) have been made possible by hybrid integration of EO polymers onto the silicon platform. This paper summarizes some of the recent progress in polymer based optical modulators and interconnects. A highly linear, broadband directional coupler modulator for use in analog optical links and compact, and low-power silicon/polymer hybrid slot photonic crystal waveguide modulators for on chip applications are presented. Recently, cost-effective roll-to-roll fabrication of electronic and photonic systems on flexible substrates has been gaining interest. A low-cost imprinted/ink-jet-printed Mach-Zehnder modulator and board-to-board optical interconnects using microlens integrated 45-degree mirror couplers compatible with the roll-to-roll fabrication platforms are also presented., Comment: 15 pages, 17 figures. arXiv admin note: text overlap with arXiv:1403.0134

The present work demonstrates an electro-optic polymer based Mach-Zehnder (MZ) modulator fabricated utilizing advanced ultraviolet (UV) imprinting and aligned ink-jet printing technologies for patterning and layer deposition. The bottom electrode layer is designed and directly ink-jet printed on the substrate to form the patterned layer. The waveguide structure is formed into a bottom cladding polymer using a transparent flexible mold based UV imprinting method. All other layers can be ink-jet printed. The top electrode is aligned and printed over the Mach-Zehnder arm. The modulator demonstrates a V-pi of 8V at 3kHz. This technology shows great potential in minimizing the fabrication complexity and roll-to-roll compatibility for manufacturing low cost, light-weight, and conformal modulators at high throughput., Comment: 3 pages, 4 figures

A method for fabricating an M.times.N, P-bit phased-array antenna on a flexible substrate is disclosed. The method comprising ink jet printing and hardening alignment marks, antenna elements, transmission lines, switches, an RF coupler, and multilayer interconnections onto the flexible substrate. The substrate of the M.times.N, P-bit phased-array antenna may comprise an integrated control circuit of printed electronic components such as, photovoltaic cells, batteries, resistors, capacitors, etc. Other embodiments are described and claimed.

NASAs future exploration missions focus on the manned exploration of the Moon, Mars, and beyond, which will rely heavily on the development of a reliable communications infrastructure from planetary surface-to-surface, surface-to-orbit, and back to Earth. Flexible antennas are highly desired in many scenarios. Active phased array antennas (active PAAs) with distributed control and processing electronics at the surface of an antenna aperture offer numerous advantages for radar communications. Large-area active PAAs on flexible substrates are of particular interest in NASA s space radars due to their efficient inflatable package that can be rolled up during transportation and deployed in space. Such an inflatable package significantly reduces stowage volume and mass. Because of these performance and packaging advantages, large-area inflatable active PAAs are highly desired in NASA s surface-to-orbit and surface-to-relay communications. To address the issues of flexible electronics, a room-temperature printing process of active phased-array antennas on a flexible Kapton substrate was developed. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proved feasible for the PAA system. This innovation is a new type of fully inkjet-printable, two-dimensional, high-frequency PAA on a flexible substrate at room temperature. The designed electronic circuit components, such as the FET switches in the phase shifter, metal interconnection lines, microstrip transmission lines, etc., are all printed using a special inkjet printer. Using the developed technology, entire 1x4, 2x2, and 4x4 PAA systems were developed, packaged, and demonstrated at 5.3 GHz. Several key solutions are addressed in this work to solve the fabrication issues. The source/drain contact is developed using droplets of silver ink printed on the source/drain areas prior to applying CNT thin-film. The wet silver ink droplets allow the silver to wet the CNT thin-film area and enable good contact with the source and drain contact after annealing. A passivation layer to protect the device channel is developed by bonding a thin Kapton film on top of the device channel. This film is also used as the media for transferring the aligned CNT thin-film on the device substrate. A simple and cost-effective technique to form multilayer metal interconnections on flexible substrate is developed and demonstrated. Contact vias are formed on the second substrate prior to bonding on the first substrate. Inkjet printing is used to fill the silver ink into the via structure. The printed silver ink penetrates through the vias to contact with the contact pads on the bottom layer. It is then annealed to form a good connection. One-dimensional and two-dimensional PAAs were fabricated and characterized. In these circuits, multilayer metal interconnects were used to make a complete PAA system.