Search

Abstract: A real-time profile control system based on PCI-bus modules has been installed in the existing plasma control system (PCS) to control high performance plasmas. In profile control, pre-programmed profile reference data, which are two-dimensional, must be manipulated as the other mono-dimensional pre-programmed reference data such as plasma current in the discharge parameter set-up and in the post-discharge data archiving process, to re-use of the existing man–machine communication tools. An preprogram algorithm number was introduced to allow the change not only of control gains but also of control algorithm during a discharge, providing flexibility and extensibility to cope with future requirements coming from control studies that are now in progress. This system has been successfully applied to safety factor profile control by lower hybrid radio frequency heating system. [Copyright &y& Elsevier]

Abstract: A fast charge exchange recombination spectroscopy (CXRS) system has been developed for the real-time measurement and feedback control of ion temperature (T i) profile and toroidal rotation velocity (V t) in JT-60U. In order to control T i and V t in real-time, the charge exchange recombination spectroscopy with high time resolution, the real-time processor system, and the real-time control system have been developed. Utilizing this system, real-time control of the T i gradient between r/a ∼0.25–0.5 has been demonstrated with neutral beams at high beta plasmas (normalized beta β N ∼1.6–2.8). The strength of the internal transport barrier is controlled. Moreover, the real-time control of V t has been demonstrated from counter (anti-parallel to the plasma current, I p) to co (parallel to the I p) direction. Then the behavior of edge localized mode (ELM) is changed by controlling the V t. [Copyright &y& Elsevier]

The old discharge control system (DCS) with HIDIC-80E mini-computer has been replaced by a control system with a unix workstation and a VME-bus system. Functionally, the workstation performs message communication with VME controller on the network, data processing using plant data and data acquisition. The commands and receiving the status data in real time. The new DCS is flexible for system extension and able to quickly respond to various requirements of software modifications. The data acquisition speed has been improved by almost a factor of two over the old one. Troubles and countermeasures experienced in the replacement work are also presented. [Copyright &y& Elsevier]

In the present RF-driven (ECCD) steady-state plasma on QUEST ( B t = 0.25 T, R = 0.68 m, a = 0.40 m), plasma current seems to flow in the open magnetic surface outside of the closed magnetic surface in the low-field region according to plasma current fitting (PCF) method. We consider that the current in the open magnetic surface is due to orbit-driven current by high-energy particles in RF-driven plasma. So based on the analysis of current density profile based on the orbit-driven current, plasma equilibrium is to be calculated. We calculated high energy particles guiding center orbits as a contour plot of conserved variable in Hamiltonian formulation and considered particles initial position with different levels of energy and pitch angles that satisfy resonance condition. Then the profile of orbit-driven current is estimated by multiplying the particle density on the resonance surface and the velocity on the orbits. This analysis shows negative current near the magnetic axis and hollow current profile is expected even if pressure driven current is considered. Considering the hollow current profile shifted toward the low-field region, the equilibrium is fitted by J-EFIT coded by MATLAB. [ABSTRACT FROM AUTHOR]

In the present RF-driven (ECCD) steady-state plasma on QUEST, the plasma current seems to flow in the open magnetic surface outside of the closed magnetic surface in the low-field region according to the plasma current fitting (PCF) method. The current in the open magnetic surface is due to the orbit-driven current by high-energy particles in the RF-driven plasma. High-energy particles guiding center orbits are calculated as contour plots of conserved variables in the Hamiltonian formulation considering particles in the initial position with different energies and pitch angles satisfying the resonance condition. A negative current appears near the magnetic axis, and a hollow current profile is expected even if the pressure driven current is considered. The equilibrium is fitted within nested magnetic surfaces by J-EFIT coded by MATLAB using the hollow current profile shift toward the low-field region. Although the plasma boundary shape reflects the plasma current density profile, the equilibrium shape fitted by J-EFIT does not coincide with the orbit-driven current profile. However, introducing an extension of the current profile without assuming nested contours into the J-EFIT code appropriately fits the plasma shape with the hollow current profile to the measured magnetic data. [ABSTRACT FROM AUTHOR]

In the present RF-driven plasma with a lot of high-energy electrons, there may be anisotropic plasma pressure, which makes the usual equilibrium analysis difficult, but the Cauchy condition surface method can reconstruct the plasma shape precisely regardless of the anisotropy. In addition, the plasma current effect in the open magnetic surfaces outside of the closed magnetic surfaces is considered in the RF-driven divertor plasma. In the reconstruction process, singular value (SV) decomposition is used and optimal criterion function for generalized cross validation is estimated concerning truncation or reduction of the small-SV components. [ABSTRACT FROM PUBLISHER]

Abstract: CCS (Cauchy Condition Surface) method is a numerical approach to reproduce plasma shape, which has good precision in conventional tokamaks. In order to apply it in plasma shape reproduction of ST (Spherical Tokamak), the calculation precision of the CCS method in a spherical tokamak CPD (Compact PWI experimental Device) (B t =0.25T, R =0.3m, a =0.2m) has been analyzed. The precision was confirmed also in ST and decided to be applied to a spherical tokamak QUEST (B t =0.25T, R =0.68m, a =0.40m).. In present stage from the magnetic measurement, it is known that the eddy current effect is large in QUEST experiment, and there are no special magnetic measurements for eddy current now, so some proper model should be selected to evaluate the eddy current effect. The eddy current density by not only CS (Center Solenoid) coil but also plasma current is calculated using EDDYCAL (JAEA). The eddy current magnitudes are taken as unknown variables and solved together with plasma shape reconstruction in ohmic discharge and ECCD (Electron Cyclotron Current Drive) discharge. [Copyright &y& Elsevier]

Abstract: Real-time processor, RTP is a basic subsystem in the JT-60 data processing system and plays an important role in JT-60 feedback control for plasma experiment. During the experiment, RTP acquires various diagnostic signals, processes them into a form of physical values, and transfers them as sensor signals to the particle supply and heating control supervisor for feedback control via reflective memory synchronization with 1ms clock signals. After the start of RTP operation in 1997, to meet the demand for advanced plasma experiment, RTP had been improved continuously such as by addition of diagnostic signals with faster digitizers, reducing time for data transfer utilizing reflective memory instead of CAMAC. However, it is becoming increasingly difficult to maintain, manage, and improve the outdated RTP with limited system CPU capability. Currently, a prototype RTP system is being developed for the next real-time processing system, which is composed of clustered system utilizing VxWorks computer. The processes on the existing RTP system will be decentralized to the VxWorks computer to solve the issues of the existing RTP system. The prototype RTP system will start to operate in August 2008. [Copyright &y& Elsevier]

Abstract: The design activity of JT-60SA (JT-60 Super Advanced) addresses the remodeling of JT-60 to a superconducting tokamak device under the JA-EU collaborative ITER–BA project. For the JT-60SA control system, the existing system should be reused as much as possible from the viewpoint of cost-effectiveness. Initial considerations of the configuration of the advanced supervisory control system (SVCS) including the following systems are: (1) an ultimate flexibility real-time control system, (2) a precision timing system able to diagnose a plasma event having a time range of ∼1μs, and (3) a safety shutdown control system. In this report, we present the design study of the JT-60SA SVCS with the focus on the above systems. [Copyright &y& Elsevier]

Abstract: Burn control simulation experiments were conducted in non-burning DD plasmas by using a burning plasma simulation scheme in JT-60U. In the burning plasma simulation scheme, two neutral beam (NB) groups were used, where one simulates α-particle heating and the other simulates external heating. The stored energy and the neutron yield rate were controlled at nearly constant values in both ELMy H-mode plasma and reversed shear (RS) plasma with an Internal Transport Barrier. In these plasmas, the NB power for the external heating simulation increased/decreased when the NB power for the α-particle heating simulation decreased/increased. Variation of the NB power for the external heating simulation was larger in the RS plasma than that in the ELMy H-mode plasma, indicating that larger control margin is necessary for the RS plasmas. In order to understand the detailed physical mechanism for the difference between ELMy H-mode and RS plasmas, we conducted numerical analysis using a 1.5-dimensional transport code. This calculation indicates the larger variation experimentally observed in the RS plasma could not be explained by the difference of the thermal diffusivity profiles or its temperature dependence. [Copyright &y& Elsevier]

Abstract: The large tokamak fusion device JT-60 is expected to explore more advanced tokamak discharge scenarios toward the ITER and a future power reactor. Since various experimental issues are to be adequately discussed, and possibly to be solved in JT-60, the plasma real-time control system has been drastically improved with remodelling in hardware as well as in software. To satisfy the requirements, a “multiple networks” structure is employed as a basic principle of the remodelling. Distributed processors for diagnostics, actuators, and supervisory controllers are linked through a reflective memory (RM) network for fast, real-time communication. Similarly, advanced and complex calculations to reproduce plasma shape and profiles are performed by several processors connected to the same RM network. In this report, we discuss the developments to improve the JT-60 plasma control and data processing systems. In addition, a future plasma control system leading to a standard design for a power reactor is outlined, which is based on the 20-year plasma operation experience. [Copyright &y& Elsevier]

The JT-60U control system, composed of a UNIX-based workstation and a VME-bus system, has been successfully performing advanced plasma control for the JT-60U plasma discharges. Various hardware modifications and advanced plasma control algorithms have been continuously integrated into the JT-60U control system since its upgrade in 1991. The ZENKEI, the supervisory control system, has been entirely converted from its original 16-bit minicomputers and CAMAC system to the combination of a workstation and VME-bus system linked through an Ethernet network. The plasma equilibrium control system utilizes a full VME-bus system composed of three DEC alpha CPU modules that are currently running at control cycle times of 250 μs. The parameters for plasma equilibrium control are calculated by a newly developed real-time plasma shape calculation and reconstruction system. These parameters are fed to the plasma equilibrium control system synchronized by 250-μs clock pulses. To progress toward the advanced plasma control concept, which includes adoption of a global plasma parameter control algorithm and suppression of MHD instabilities, improvements were extensively consolidated into the plasma control system (PCS). Currently, additional modifications of the JT-60U control system have extended the pulse duration of the discharge without a major change in JT-60 equipment. [Copyright &y& Elsevier]