Search

The development of easy and direct real-time monitoring of welded joint quality instead of surface damage analysis is crucial to improve the quality of industrial products. This work presents the results of high-density polyethylene (HDPE)-based composites with various carbon black (CB) content (from 20 to 30 vol.%) for use as a heating element and strain sensor in electrofusion-welded polymer joints. The pyroresistive heating process was used to determine the effect of generated Joule heat during welding on the structure and sensor properties of polymer–carbon composites. It is shown that the generation of Joule heat depends on the nanocarbon content and affects the crystallinity of the polymer matrix. The partial disruption of the conductive path of carbon black particles was observed and, as a result, a decrease in electrical conductivity for composites with lower CB content after welding was found. For the highest CB amount, conductivity increased, which is caused by smaller particle-to-particle distance for filler paths. Therefore, the best balance between pyroresistive and sensor properties was found. [ABSTRACT FROM AUTHOR]

This work describes impact of concentration of BiFeO3 submicrometric particles on piezoelectric performance and structural characteristics of 0–3 polymer composites with a polystyrene matrix. Bismuth ferrite particles are fabricated using reverse co‐precipitation method, followed by ultrasonic dispersion in a solvent to break up agglomerates formed during sintering, resulting in particles with a size of ≈200 nm. It is found that concentrations higher than 10 wt% BiFeO3 lead to a disturbance in natural organization of polystyrene. The hindered organization of side‐groups by submicrometric filler, occurring during solvent evaporation, strongly affects the mechanical properties of the finalcomposite, significantly increasing Young's modulus and tensile strength, but decreasing elongation. Such behavior is detected and described for the firsttime in literature. Piezoelectric examinations show that the thermal depolarization of nanogenerators has a different impact depending on the amountof piezoelectric phase. The study reveals that a voltage of over 4.8 V is generated when dynamic air pressure is applied at 11.54 bar for the composite containing only 2.5 wt% BiFeO3. For composites with 10% weight fraction or lower, decrease in generated voltage after thermal depolarization is about 24%, while for higher weight fractions (15 and 20 wt%) the decrease is around 35%. [ABSTRACT FROM AUTHOR]

To create materials that interact effectively with electromagnetic (EM) radiation, new nanosized substituted ferrites (NiZn)1−xMnxFe2O4 (x = 0, 0.5, and 1) anchored on the surface of multi-walled carbon nanotubes (CNTs) have been synthesized. The concentration of CNTs in the (NiZn)1−xMnxFe2O4/CNT system was from 0.05 to 0.07 vol. fractions. The dielectric and magnetic characteristics of both pristine (NiZn)1−xMnxFe2O4 ferrites and (NiZn)1−xMnxFe2O4/CNT composite systems were studied. The introduction of (NiZn)1−xMnxFe2O4/CNT composites into the amorphous epoxy matrix allows to tailor absorbing properties at the high-frequency by effectively shifting the maximum peak values of the absorption and reflection coefficient to a region of lower frequencies (20–30 GHz). The microwave adsorption properties of (NiZn)1−xMnxFe2O4/0.07CNT–ER (x = 0.5) systems showed that the maximum absorption bandwidth with reflection loss below −10 dB is about 11 GHz. [ABSTRACT FROM AUTHOR]

Growing demand for electric energy in newly developed electronic systems causes increasing interest in research on piezoelectric nanogenerators (PENGs). Design and fabrication of such devices is challenging, considering cost of materials used in their construction. This is the main reason why intensive research has begun on 0‐3 composites with piezoelectric properties. One of the most promising constituent materials for composites fabrication are polymers, due to their low cost and easy processing. Herein, we present fabricated wearable PENG with good impact and vibration energy conversion properties. Correlation between matrix stiffness and piezoelectric properties of 0‐3 type composite is proposed. It was found that composite with 10 wt.% of BiFeO3 particles exhibits power output density for vibrations, finger tapping, and air stream pressure P = 11.12 nW cm−3, P = 4.83 μW cm−3, and P = 769.2 μW cm−3, respectively. Decrease in stiffness of epoxy matrix results at least in two‐times lower power output density for this same PENG. The obtained results demonstrate that the fabricated BFO/epoxy composites show the wide applicability and potential to be integrated with other functional devices, for example, as a part of wearable devices in smart shoes. [ABSTRACT FROM AUTHOR]

The nonviable allogeneic human skin grafts might be considered as the most suitable skin substitutes in the treatment of extensive and deep burns. However, in accordance to biological security such grafts require the final sterilization prior to clinical application. The aim of the study was to verify the influence of electron beam irradiation of three selected doses: 18, 25, and 35 kGy on the extracellular matrix of human skin. Prior to sterilization, the microbiological tests were conducted and revealed contamination in all examined cases. Individual groups were subjected to single electron beam radiation sterilization at proposed doses and then subjected to microbiological tests again. The results of microbiological testing performed for all irradiation doses used were negative. Only in the control group was a growth of microorganisms observed. The FTIR spectrometry tests were conducted followed by the histological evaluation and mechanical tests. In addition, cost analysis of radiation sterilization of individual doses was performed. The results of spectroscopic analysis, mechanical tests, and histological staining showed no significant changes in composition and characteristics of tested tissues after their irradiation, in comparison to control samples. The cost analysis has shown that irradiation with 18 kGy is the most cost‐effective and 35 kGy is the least favorable. However, according to biological risk reduction, the recommended sterilization dose is 35 kGy, despite the higher price compared to the other doses tested. [ABSTRACT FROM AUTHOR]

The use of graphene materials, i.e. graphene oxide, reduced graphene oxide, graphene nanoplatelets and their functionalized forms as fillers of epoxy composites, is reviewed. The purpose of the time- and reagent consuming functionalization methods of graphene materials is justified by the noticeable improvement of dispersity and adhesion of the graphene sheets to the epoxy matrix, which affects the final properties of graphene-epoxy composites. The state-of-the-art of multifunctional graphene-epoxy composites developed over the last years is critically reviewed. The influence of the graphene filler structure and dispersion preparing procedure on the morphology of epoxy-graphene composites and, consequently, their electrical and thermal conductivities, mechanical strength and flame retardant characteristics is considered. An evolution from epoxy-graphite microcomposites to epoxy-graphene nanocomposites is presented, showing the benefits of graphene materials for composites. Some recent works on the epoxy composites reinforced with hybrid graphene fillers and combinations of graphene materials with other fillers are described. [ABSTRACT FROM AUTHOR]