Search

Background: Initial promise of a stand-alone interbody fusion cage to treat chronic back pain and restore disc height has not been realized. In some instances, a posterior spinal fixation has been used to enhance stability and increase fusion rate. In this manuscript, a new stand-alone cage is compared with conventional fixation methods based on the finite element analysis, with a focus on investigating cage-bone interface mechanics and stress distribution on the adjacent tissues.Methods: Three trapezoid 8 degrees interbody fusion cage models (dual paralleled cages, a single large cage, or a two-part cage consisting of a trapezoid box and threaded cylinder) were created with or without pedicle screws fixation to investigate the relative importance of the screws on the spinal segmental response. The contact stress on the facet joint, slip displacement of the cage on the endplate, and rotational angle of the upper vertebra were measured under different loading conditions.Results: Simulation results demonstrated less facet stress and slip displacement with the maximal contact on the cage-bone interface. A stand-alone two-part cage had good slip behavior under compression, flexion, extension, lateral bending and torsion, as compared with the other two interbody cages, even with the additional posterior fixation. However, the two-part cage had the lowest rotational angles under flexion and torsion, but had no differences under extension and lateral bending.Conclusion: The biomechanical benefit of a stand-alone two-part fusion cage can be justified. This device provided the stability required for interbody fusion, which supports clinical trials of the cage as an alternative to circumferential fixations. [ABSTRACT FROM AUTHOR]

Background: The association of lumbar spine instability between laminectomy and laminotomy has been clinically studied, but the corresponding in vitro biomechanical studies have not been reported. We investigated the hypothesis that the integrity of the posterior complex (spinous process-interspinous ligament-spinous process) plays an important role on the postoperative spinal stability in decompressive surgery.Methods: Eight porcine lumbar spine specimens were studied. Each specimen was tested intact and after two decompression procedures. All posterior components were preserved in Group A (Intact). In Group B (Bilateral laminotomy), the inferior margin of L4 lamina and superior margin of L5 lamina were removed, but the L4-L5 supraspinous ligament was preserved. Fenestrations were made on both sides. In Group C (Laminectomy) the lamina and spinous processes of lower L4 and upper L5 were removed. Ligamentum flavum and supraspinous ligament of L4-L5 were removed. A hydraulic testing machine was used to generate an increasing moment up to 8400 N-mm in flexion and extension. Intervertebral displacement at decompressive level L4-L5 was measured by extensometerResults: The results indicated that, under extension motion, intervertebral displacement between the specimen in intact form and at two different decompression levels did not significantly differ (P > 0.05). However, under flexion motion, intervertebral displacement of the laminectomy specimens at decompression level L4-L5 was statistically greater than in intact or bilateral laminotomy specimens (P = 0.0000963 and P = 0.000418, respectively). No difference was found between intact and bilateral laminotomy groups. (P > 0.05).Conclusion: We concluded that a lumbar spine with posterior complex integrity is less likely to develop segment instability than a lumbar spine with a destroyed anchoring point for supraspinous ligament. [ABSTRACT FROM AUTHOR]

Background Context: Patients with osteoporosis experience a higher risk of pedicle screw loosening and failure, making PMMA bone cement augmentation a common recommendation to increase stability. However, there is ongoing debate about the ideal cement volume, filling pattern, and measurable increase in stability that cement provides., Purpose: This aim of this study is to clarify the impact of cement volume and filling pattern on the stability of pedicle screws in synthetic bone blocks of varying density., Study Design: We examined the effects of different volumes of PMMA cement on screw stability by using synthetic bone blocks with densities of 7.5 pcf, 15 pcf, and 30 pcf to simulate human vertebral cancellous bone with osteoporosis, osteopenia, and normal bone density. Two filling patterns were compared: a tip cement cloud and a surrounding cement cloud., Methods: We tested solid screws, cannulated screws without side holes, and cannulated screws with 4 side holes. Cement volumes of 2 cc, 3 cc, and 4 cc were injected, and the pullout strength was measured using an Instron testing machine. The samples were categorized into the control (no cement) group, S group (solid screws with prefilling), C1 group (cannulated screws without side holes), and C5 group (cannulated screws with 4 side holes). Among these, the C1 group exhibited a cement cloud at the tip, while the S and C5 groups showed a surrounding cement cloud., Results: Adding an extra 1 cc of cement (from 2 cc to 3 cc, or 3 cc to 4 cc) significantly increased the pullout strength by 10% in 7.5 pcf bone, 47% in 15 pcf bone, and 34% in 30 pcf bone and doubling the cement volume resulted in even greater increases. Regardless of the injected volume, cement augmentation substantially increased the pullout strength in osteoporotic bone compared with noncemented screws in osteopenic bone. For a given cement volume, the anchorage power was greater for the surrounding cement cloud pattern than for the tip cement cloud pattern., Conclusion: Although the addition of more cement increases the pullout strength, excessive augmentation in osteoporotic bone is unnecessary. The filling pattern is crucial; a larger contact area in the surrounding cement cloud enhances screw stability more effectively than the tip cement cloud does., Clinical Significance: While adding more cement increases pullout strength, excessive augmentation in osteoporotic bone is unnecessary. The filling pattern rather than the screw design is a crucial determinant of screw stability., Competing Interests: Declarations of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2025 The Author(s). Published by Elsevier Inc. All rights reserved.)

Objective: To develop and validate a predictive model for assessing the risk of early postoperative high intraocular pressure (HIOP) following posterior chamber intraocular lens implantation. Methods: The clinical data of patients who underwent posterior chamber intraocular lens implantation at the Second Affiliated Hospital of Zhejiang University School of Medicine between May 2023 and April 2024 were retrospectively reviewed. Patients were divided into a modeling group and a validation group with a 7∶3 ratio using computerized random allocation. The modeling group was further categorized into normal intraocular pressure and HIOP groups based on the occurrence of early postoperative HIOP. Multivariate logistic regression analysis was employed to establish a risk prediction model. Receiver operating characteristic (ROC) curve analysis was conducted using R software to assess the predictive ability and accuracy of the model, along with calibration and decision curve analysis (DCA) curve plotting. Results: A total of 239 patients (478 eyes) were enrolled. The modeling group consisted of 168 patients (82 males and 86 females) (336 eyes), with an average age of (25.5±5.1) years. The validation group consisted of 71 patients (36 males and 35 females) (142 eyes), with an average age of (24.7±5.7) years. The early postoperative HIOP incidence rate after posterior chamber intraocular lens implantation was 32.4% (109/336), while it was 26.8% (38/142) in the validation group. The multivariate logistic regression analysis indicated that preoperative refractive diopter ( OR =0.873, 95% CI : 0.782-0.976, P =0.017), corneal endothelial cell count ( OR =0.996, 95% CI : 0.995-0.997, P <0.001), corneal thickness ( OR =1.015, 95% CI : 1.006-1.024, P =0.001), and preoperative intraocular pressure ( OR =1.470, 95% CI : 1.283-1.686, P <0.001) were associated factors for early HIOP. The Hosmer-Lemeshow test showed that the χ 2 value was 8.444 ( P =0.391), and the area under the ROC curve (AUC) was 0.888 (95% CI : 0.852-0.925). The Youden index reached its maximum value of 0.646, with a sensitivity of 0.862 and specificity of 0.784. AUC of validation group was 0.921 (95% CI : 0.870-0.972), with a maximum Youden index of 0.765, sensitivity of 0.842 and specificity of 0.923. Conclusions: The risk prediction model constructed based on preoperative refractive diopter, corneal endothelial cell count, corneal thickness, and preoperative intraocular pressure demonstrates good predictive performance for early postoperative HIOP following posterior chamber intraocular lens implantation.

Objective: Combining oblique lumbar interbody fusion (OLIF) with posterior pedicle screw fixation (PPSF) has been proposed to reduce cage subsidence, especially in osteoporotic spines. Recently, anterolateral screw-rod fixation has gained interest as it allows direct pathology observation and avoids a posterior approach. However, controversies exist between anterolateral screw fixation systems and traditional PPSF due to variations in osteoporotic vertebral mineral density, screw fixation positions, and fixation methods (bicortical vs. unicortical). This study aimed to investigate the biomechanical impact of fixation position and method in osteoporotic spine., Methods: Seventy-two fresh‑frozen porcine vertebrae (L1-6) were decalcified using 0.5 M EDTA and divided into two groups based on fixation method: bicortical or unicortical. Six groups for each method were created according to the screw position in the lateral vertebral body, with six specimens in each group: anterior, central, and posterior in the middle body and para-endplate regions. Correlations among screw position, fixation method and axial pullout strength were analyzed., Results: A 4-week decalcification process, bone mineral density in the porcine vertebrae decreased to approximately 48% (p < 0.05) of the original value, categorizing them as osteoporotic. Bicortical fixation showed significantly greater pullout forces than unicortical fixation, with differences ranging from 82 to 273%. Notably, central or posterior screws outperformed anterior screws in pullout strength., Conclusion: Bicortical fixation exhibited significantly greater pullout forces than unicortical fixation. We suggest positioning screws in the central or posterior region of the middle body with bicortical fixation in osteoporotic vertebrae., Competing Interests: Declarations. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

Background: Pediatric supracondylar humeral fractures present considerable surgical challenges due to the difficulty of achieving proper fracture alignment and stable fixation while avoiding injury to the ulnar nerve. This study assesses the biomechanical performance of a novel Kirschner wire (K-wire) fixation device (KFD), designed to enhance stability and reduce complications linked to traditional K-wire configurations., Methods: Using finite element analysis (FEA), we evaluated four fixation strategies for treatment of pediatric supracondylar humeral simple transverse fractures: crossed pin fixation, crossed pin fixation with KFD, two lateral pin fixation, and two lateral pin fixation with KFD, under various mechanical loads. The analysis focused on the stress and strain experienced by the K-wires at the fracture site during torsional and bending forces., Results: FEA revealed that the KFD significantly reduced the stress and strain on the K-wires in all configurations. In both crossed pin and two lateral pin fixation methods, the addition of the KFD showed lower stress and strain levels compared to setups without the KFD., Conclusion: This study demonstrates the potential of the KFD to enhance fracture stability and reduce mechanical stress at the fracture site, suggesting a promising improvement in the treatment of pediatric supracondylar humeral fractures. This innovation may contribute to safer and more reliable outcomes in pediatric orthopedic surgery., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2024 Lu, Tai, Lee, Wang, Mao, Yang, Chang and Kao.)

Background Context: Long-segment pedicle screw instrumentation is widely used to treat complex spinal disorders. Rods are routinely precontoured to maximize assistance on the correcting side of the deformity, but there often exists a residual gap discrepancy between the precontoured rods and screw tulips. No previous research has investigated the diminished pullout strength of the most proximal or distal pedicle screw resulting from a mismatched rod in long-segment pedicle screw instrumentation., Purpose: The present study aimed to investigate the decreased pullout force of pedicle screws affected by the gap discrepancy when forcefully engaging a mismatched rod into a tulip in a normal-density porcine spine., Study Design: The pedicle screw fixation strength under axial pullout force was compared among three different gap discrepancies between rods and tulips using long porcine spine segments., Methods: Twelve porcine lumbar vertebrae (L3-L6) were implanted with pedicle screws and rods. Screws on one side had no gap between the tulip and rod (0-mm group), while the most proximal screw on the other side had an intentional gap of 3 mm (3-mm group) or 6 mm (6-mm group). Three hours after forcefully engaging the rod into the tulips at room temperature, the set screws in all specimens were loosened, and each specimen was dissected into individual vertebrae for subsequent pullout testing., Results: The control group exhibited significantly greater pullout strength (1987.68 ± 126.80 N) than the groups from different rod-tulip configurations (p<.05), with significantly greater strength in the 3-mm group (945.62 ± 97.43 N) than the 6-mm group (655.30 ± 194.49 N) (p<.05). Only 47.6% and 33.0% of the pullout strength was retained in the 3-mm and 6-mm groups, respectively, compared to the control group., Conclusions: Gap discrepancies between rods and tulips can significantly reduce pedicle screw pullout strength, with a correlation between decreased strength and increased gaps. Surgeons should avoid forcefully engaging mismatched rods and consider well-fitted contoured rods in spinal surgery to minimize the risk of screw loosening., Clinical Significance: The gap discrepancy between rod and tulip significantly affected pullout strength, with greater gaps leading to reduced strength. Forcefully engaging mismatched rods into tulips in degenerative spinal surgery should be avoided to minimize the risk of early screw pullout., (Copyright © 2024 The Author(s). Published by Elsevier Inc. All rights reserved.)

Videos are an accessible form of media for analyzing sports postures and providing feedback to athletes. Existing sport-specific systems embed bespoke human pose attributes and thus can be hard to scale for new attributes, especially for users without programming experiences. Some systems retain scalability by directly showing the differences between two poses, but they might not clearly visualize the key differences that viewers would like to pursue. Besides, video-based coaching systems often present feedback on the correctness of poses by augmenting videos with visual markers or reference poses. However, previewing and augmenting videos limit the analysis and visualization of human poses due to the fixed viewpoints in videos, which confine the observation of captured human movements and cause ambiguity in the augmented feedback. To address these issues, we study customizable human pose data analysis and visualization in the context of running pose attributes, such as joint angles and step distances. Based on existing literature and a formative study, we have designed and implemented a system, PoseCoach, to provide feedback on running poses for amateurs by comparing the running poses between a novice and an expert. PoseCoach adopts a customizable data analysis model to allow users' controllability in defining pose attributes of their interests through our interface. To avoid the influence of viewpoint differences and provide intuitive feedback, PoseCoach visualizes the pose differences as part-based 3D animations on a human model to imitate the demonstration of a human coach. We conduct a user study to verify our design components and conduct expert interviews to evaluate the usefulness of the system.

Despite advancements in pedicle screw design and surgical techniques, the standard steps for inserting pedicle screws still need to follow a set of fixed procedures. The first step, known as establishing a pilot hole, also referred to as a pre-drilled hole, is crucial for ensuring screw insertion accuracy. In different surgical approaches, such as minimally invasive or traditional surgery, the method of creating pilot holes varies, resulting in different pilot hole profiles, including variations in size and shape. The aim of this study is to evaluate the biomechanical properties of different pilot hole profiles corresponding to various surgical approaches. Commercially available synthetic L4 vertebrae with a density of 0.16 g/cc were utilized as substitutes for human bone. Four different pilot hole profiles were created using a 3.0 mm cylindrical bone biopsy needle, 3.6 mm cylindrical drill, 3.2-5.0 mm conical drill, and 3.2-5.0 mm conical curette for simulating various minimally invasive and traditional spinal surgeries. Two frequently employed screw shapes, namely, cylindrical and conical, were selected. Following specimen preparation, screw pullout tests were performed using a material test machine, and statistical analysis was applied to compare the mean maximal pullout strength of each configuration. Conical and cylindrical screws in these four pilot hole configurations showed similar trends, with the mean maximal pullout strength ranking from high to low as follows: 3.0 mm cylindrical biopsy needle, 3.6 mm cylindrical drill bit, 3.2-5.0 mm conical curette, and 3.2-5.0 mm conical drill bit. Conical screws generally exhibited a greater mean maximal pullout strength than cylindrical screws in three of the four different pilot hole configurations. In the groups with conical pilot holes, created with a 3.2-5.0 mm drill bit and 3.2-5.0 mm curette, both conical screws exhibited a greater mean maximal pullout strength than did cylindrical screws. The strength of this study lies in its comprehensive comparison of the impact of various pilot hole profiles commonly used in clinical procedures on screw fixation stability, a topic rarely reported in the literature. Our results demonstrated that pilot holes created for minimally invasive surgery using image-guided techniques exhibit superior pullout strength compared to those utilized in traditional surgery. Therefore, we recommend prioritizing minimally invasive surgery when screw implantation is anticipated to be difficult or there is a specific need for stronger screw fixation. When opting for traditional surgery, image-guided methods may help establish smaller pilot holes and increase screw fixation strength., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2024 Li, Lai, Hsieh, Chen, Lee, Tsai and Tai.)

Ball-and-socket designs of cervical total disc replacement (TDR) have been popular in recent years despite the disadvantages of polyethylene wear, heterotrophic ossification, increased facet contact force, and implant subsidence. In this study, a non-articulating, additively manufactured hybrid TDR with an ultra-high molecular weight polyethylene core and polycarbonate urethane (PCU) fiber jacket, was designed to mimic the motion of normal discs. A finite element (FE) study was conducted to optimize the lattice structure and assess the biomechanical performance of this new generation TDR with an intact disc and a commercial ball-and-socket Baguera ® C TDR (Spineart SA, Geneva, Switzerland) on an intact C5-6 cervical spinal model. The lattice structure of the PCU fiber was constructed using the Tesseract or the Cross structures from the IntraLattice model in the Rhino software (McNeel North America, Seattle, WA) to create the hybrid I and hybrid II groups, respectively. The circumferential area of the PCU fiber was divided into three regions (anterior, lateral and posterior), and the cellular structures were adjusted. Optimal cellular distributions and structures were A2L5P2 in the hybrid I and A2L7P3 in the hybrid II groups. All but one of the maximum von Mises stresses were within the yield strength of the PCU material. The range of motions, facet joint stress, C6 vertebral superior endplate stress and path of instantaneous center of rotation of the hybrid I and II groups were closer to those of the intact group than those of the Baguera ® C group under 100 N follower load and pure moment of 1.5 Nm in four different planar motions. Restoration of normal cervical spinal kinematics and prevention of implant subsidence could be observed from the FE analysis results. Superior stress distribution in the PCU fiber and core in the hybrid II group revealed that the Cross lattice structure of a PCU fiber jacket could be a choice for a next-generation TDR. This promising outcome suggests the feasibility of implanting an additively manufactured multi-material artificial disc that allows for better physiological motion than the current ball-and-socket design., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Hsieh, Tai, Li, Lee, Lin, Tsai, Lai and Chen.)

Intraoperative pedicle screw depth adjustment after initial insertion, including both forward and backward adjustments, is sometimes necessary to facilitate rod application and ensure that the screw is in the correct position, which is determined by intraoperative fluoroscopy. Adjusting the screw with forward turns has no negative influence on the screw fixation stability; however, screw turnback may weaken the fixation stability. The aim of this study is to evaluate the biomechanical properties of screw turnback and demonstrate the reduction in the fixation stability after the screw is turned 360° from its full insertion position. Commercially available synthetic closed-cell polyurethane foams with three different densities simulating various degrees of bone density were utilized as substitutes for human bone. Two different screw shapes (cylindrical and conical) together with two different pilot hole profiles (cylindrical and conical) were tested. Following specimen preparation, screw pullout tests were conducted using a material test machine. The mean maximal pullout strength between full insertion and 360-degree turnback from full insertion in each setting was statistically analyzed. The mean maximal pullout strength after 360-degree turnback from full insertion was generally lower than that at full insertion. The reduced mean maximal pullout strength after turnback increased with decreasing bone density. Conical screws had significantly lower pullout strength after 360-degree turnback than cylindrical screws. The mean maximal pullout strength was reduced by up to approximately 27% after 360-degree turnback when using a conical screw in a low bone density specimen. Additionally, specimens treated with a conical pilot hole presented a less reduction in pullout strength after screw turnback as compared to those with a cylindrical pilot hole. The strength of our study was that we systematically investigated the effects of various bone densities and screw shapes on screw stability after turnback, which has rarely been reported in the literature. Our study suggests that pedicle screw turnback after full insertion should be reduced in spinal surgeries, particularly procedures that use conical screws in osteoporotic bone. Pedicle screw secured with a conical pilot hole might be beneficial for screw adjustment., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Li, Hsieh, Chen, Lee, Tsai, Lai and Tai.)

Background Context: Pedicle screw-rod assembly procedures following pedicle screw insertion include contouring and placing rods into screw tulips, introducing set screws into the tulip along the screw thread, applying a counter-torque holder and tightening all the set screws clockwise. Even if an appropriate pedicle screw is implanted, screw dislodgement after tightening of the tulip and set screw is not uncommon. Pedicle wall violation resulting from excessive rotational force due to inadequate use of a counter-torque holder might be the reason. However, the strain change in the pedicle during tulip-set screw tightening and the role of counter-torque have never been investigated., Purpose: This study determined differences in the strain change in the outer and inner pedicle walls during tulip-set screw tightening; additionally, the influence of counter-torque on pedicle wall violation was elucidated., Study Design: A controlled biomechanical study; the strain values of outer and inner pedicle walls in cadaveric porcine L4-L5 vertebrae during tulip-set screw tightening with or without a counter-torque holder were measured., Methods: Twelve L4-L5 fresh-frozen porcine lumbar vertebrae were implanted with screw-rod constructs; the set screw was randomly locked into the tulip in the right L5, right L4, left L5 and left L4 testing groups. The maximal values from eight strain gauges (P-R-O: outer cortex of right pedicle in proximal vertebra; P-R-I: inner cortex of right pedicle in proximal vertebra; D-R-O: outer cortex of right pedicle in distal vertebra; D-R-I: inner cortex of right pedicle in distal vertebra; P-L-O: outer cortex of left pedicle in proximal vertebra; P-L-I: inner cortex of left pedicle in proximal vertebra; D-L-O: outer cortex of left pedicle in distal vertebra; D-L-I: outer cortex of left pedicle in proximal vertebra) for each specimen during tightening to 12 Nm were measured., Results: The maximal strain values of the ipsilateral strain gauges in all testing groups were almost significantly higher when a counter-torque holder was not used than when one was used. The strain values in the adjacent pedicle of specimens without a counter-torque holder were significantly increased: P-R-O and P-R-I in the right L5 group; D-R-I in the right L4 group; P-L-I and P-L-O in the left L5 group; D-L-O and D-L-I in the left L4 group., Conclusions: The constraint effect of counter-torque during tulip-set screw tightening is necessary. Clockwise rotational force with a fragile lateral pedicle wall suggests that caution is required when using a counter-torque holder to tighten the right L5 and left L4 constructs., Clinical Significance: A counter-torque holder is important during tulip-set screw tightening; improper use may lead to adjacent pedicle wall violation, sequentially resulting in pedicle screw loosening., Competing Interests: Declarations of Competing Interest None., (Copyright © 2022 The Authors. Published by Elsevier Inc. All rights reserved.)

Although an anterior approach with anterior lateral screw fixation has been developed for stabilizing the thoracolumbar spine clinically, screw loosening still occurs. In this novel in vitro study, we attempted to elucidate the optimal screw position in the lateral lumbar vertebra and the effect of bicortical fixation. A total of 72 fresh-frozen lumbar vertebrae from L1-6 were harvested from 12 mature pigs and randomly assigned to two modalities: bicortical fixation (n = 36) and unicortical fixation (n = 36). Six groups of screw positions in the lateral vertebral body in each modality were designated as central-anterior, central-middle, central-posterior, lower-anterior, lower-middle, and lower- posterior; 6 specimens were used in each group. The correlations between screw fixation modalities, screw positions and axial pullout strength were analyzed. An appropriate screw trajectory and insertional depth were confirmed using axial and sagittal X-ray imaging prior to pullout testing. In both bicortical and unicortical fixation modalities, the screw pullout force was significantly higher in the posterior or middle position than in the anterior position (p < 0.05), and there was no significant differences between the central and lower positions. The maximal pullout forces from the same screw positions in unicortical fixation modalities were all significantly lower, decreases that ranged from 32.7 to 74%, than those in bicortical fixation modalities. Our study using porcine vertebrae showed that screws in the middle or posterior position of the lateral vertebral body had a higher pullout performance than those in the anterior position. Posteriorly positioned lateral vertebral screws with unicortical fixation provided better stability than anteriorly positioned screws with bicortical fixation., (© 2023. The Author(s).)

Study Design: Biomechanical study., Objective: Cross-links are a type of common clinical spinal instrumentation. However, the effects of the position and number of cross-links have never been investigated in long-segment spinal fixation, and the variables have not been optimized. We conducted an in vitro biomechanical study by using a porcine long-segment spinal model with 5 different crosslink configurations to determine the optimal construct for clinical practice., Methods: Five modalities with paired segmental screws from T15-L5 were tested in 20 porcine spines. The spines without cross-links composed the control group, Group A; those with a single cross-link from L2-3 composed Group B; those with 2 cross-links from L1-2 and L3-4 composed Group C; those with 2 cross-links from T15-L1 and L4-5 composed Group D; and those with 3 cross-links from T15-L1, L2-3 and L4-5 composed Group E. Spinal stiffnesses in flexion, extension, lateral bending, and axial rotation were compared among 5 different cross-link configurations in 5-level porcine spinal units., Results: Flexional, extensional and lateral bending stiffnesses did not significantly change with an increasing number of cross-links or positions in the construct. Axial stiffness was significantly increased with 2 cross-links compared to one ( P < 0.05) and with placement more distant from the center of the long spinal fixation construct ( P < 0.05)., Conclusions: Two cross-links individually placed proximal and distal from the center of a construct is an optimal and efficient configuration to achieve biomechanical stability in non-rigid lumbar spines undergoing long-level fixation.

Three key factors are responsible for the biomechanical performance of pedicle screw fixation: screw mechanical characteristics, bone quality and insertion techniques. To the best of the authors' knowledge, no study has directly compared the biomechanical performance among three trajectories, i.e., the traditional trajectory (TT), modified trajectory (MT) and cortical bone trajectory (CBT), in a porcine model. This study compared the pullout strength and insertion torque of three trajectory methods in single vertebrae, the pullout strength and fixation stiffness including flexion, extension, and lateral bending in a one-level instrumented functional spinal unit (FSU) that mimics the in vivo configuration were clarified. A total of 18 single vertebrae and 18 FSUs were randomly assigned into three screw insertion methods ( n = 6 in each trajectory group). In the TT group, the screw converged from its entry point, passed completely inside the pedicle, was parallel to the superior endplate, was located in the superior third of the vertebral body and reached to at least the anterior third of the vertebral body. In the MT group, the convergent angle was similar to that of the TT method but directed caudally to the anterior inferior margin of the vertebral body. The results of insertion torque and pullout strength in single vertebrae were analyzed; in addition, the stiffness and pullout strength in the one-level FSU were also investigated. This study demonstrated that, in single vertebrae, the insertion torque was significantly higher in CBT groups than in TT and MT groups ( p < 0.05). The maximal pullout strength was significantly higher in MT groups than in TT and CBT groups ( p < 0.05). There was no significant difference in stiffness in the three motions among all groups. The maximal pullout strength in FSUs of MT and CBT groups were significantly higher than the TT groups ( p < 0.05). We concluded that either MT or CBT provides better biomechanical performance than TT in single vertebrae or FSUs. The lack of significance of stiffness in FSUs among three methods suggested that MT or CBT could be a reasonable alternative to TT if the traditional trajectory was not feasible., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Tai, Chen, Liu, Li, Tsai, Lai and Hsieh.)

Pedicle screw fixation is one of the most common procedures used in spinal fusion surgery. The screw loosening is a major concern, which may be caused by broken pedicles. In vitro pullout tests or insertion torque are the main approaches for assessing the stability of the screw; however, direct evidence was lacking for clinical human spines. Here, we aim to provide a model that can predict the pullout strengths of pedicle screws in various pedicle conditions from X-ray images. A weighted embedded bone volume (EBV) model is proposed for pullout strengths prediction by considering the bone heterogeneity and confinement of the screw. We showed that the pullout strength is proportional to the EBV for homogeneous bone and the weighted EBV for layered composite bone. The proposed weighted EBV model is validated with in vitro Sawbones® pullout experiments. The results show that the model has better accuracy than the simple EBV model, with a coefficient of determination of 0.94. The proposed weighted EBV model can help assess the stability of a pedicle screw in a broken pedicle by simply examining 2D X-ray images., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

In recent years, sparse voxel-based methods have become the state-of-the-arts for 3D semantic segmentation of indoor scenes, thanks to the powerful 3D CNNs. Nevertheless, being oblivious to the underlying geometry, voxel-based methods suffer from ambiguous features on spatially close objects and struggle with handling complex and irregular geometries due to the lack of geodesic information. In view of this, we present Voxel-Mesh Network (VMNet), a novel 3D deep architecture that operates on the voxel and mesh representations leveraging both the Euclidean and geodesic information. Intuitively, the Euclidean information extracted from voxels can offer contextual cues representing interactions between nearby objects, while the geodesic information extracted from meshes can help separate objects that are spatially close but have disconnected surfaces. To incorporate such information from the two domains, we design an intra-domain attentive module for effective feature aggregation and an inter-domain attentive module for adaptive feature fusion. Experimental results validate the effectiveness of VMNet: specifically, on the challenging ScanNet dataset for large-scale segmentation of indoor scenes, it outperforms the state-of-the-art SparseConvNet and MinkowskiNet (74.6% vs 72.5% and 73.6% in mIoU) with a simpler network structure (17M vs 30M and 38M parameters).

Polymethylmethacrylate (PMMA) has been applied clinically and biomechanically repair loose pedicle screws. Controversies have arisen over data due to uncontrolled cement properties, various locations and sizes of fenestrated holes in repair screws, irregular holes and different bone densities of specimens. In this study, the pullout strength was compared for two techniques, the modified technique to use PMMA to augment a threaded hole and the traditional technique with retrograde injection of a PMMA filling, for standard loose screws in porcine vertebrae. Both techniques provided statistically significant results for sufficiently randomized specimens and experimental procedures. The difference in the pullout strength between conical and cylindrical screws for the aforementioned cement augmentation techniques was also investigated. Twenty-four single-level fresh-frozen lumbar vertebrae from L1 to L6 were harvested from four mature pigs. A total of 0.8 ml of PMMA was retrograde injected into screw holes with a 5.5 mm diameter, followed by insertion of a 5.0 mm diameter repair screw in the traditional group (n = 12). A stiff threaded PMMA hole was created with a 4.5 mm tapping screw before insertion of repair screws in the modified group (n = 12). Two screw geometries were randomly assigned as cylindrical (n = 6) and conical (n = 6) in each group. The correlations between filling techniques, screw geometries and axial pullout strength were analyzed. An appropriate screw trajectory and insertion depth were confirmed using X-ray imaging prior to pullout testing in both groups. For a given screw geometry (cylindrical or conical), the pullout force of the modified group was significantly higher than that of the traditional group. There was no significant difference in the pullout force between the screw geometries for a given filling technique. The cement augmentation technique is far more influential than the screw outer geometry. The modified PMMA technique created a greater anchor force than the traditional method and could be an alternative for revision of pedicle screw loosening., (© 2022. The Author(s).)

Osteoporosis is a critical problem during aging. Ultrasound signals backscattered from bone contain information associated with microstructures. This study proposed using entropy imaging to collect the information in bone microstructures as a possible solution for ultrasound bone tissue characterization. Bone phantoms with different pounds per cubic foot (PCF) were used for ultrasound scanning by using single-element transducers of 1 (nonfocused) and 3.5 MHz (nonfocused and focused). Clinical measurements were also performed on lumbar vertebrae (L3 spinal segment) in participants with different ages (n = 34) and postmenopausal women with low or moderate-to-high risk of osteoporosis (n = 50; identified using the Osteoporosis Self-Assessment Tool for Taiwan). The signals backscattered from the bone phantoms and subjects were acquired for ultrasound entropy imaging by using sliding window processing. The independent t-test, one-way analysis of variance, Spearman correlation coefficient r s , and the receiver operating characteristic (ROC) curve were used for statistical analysis. The results indicated that ultrasound entropy imaging revealed changes in bone microstructures. Using the 3.5-MHz focused ultrasound, small-window entropy imaging (side length: one pulse length of the transducer) was found to have high performance and sensitivity in detecting variation among the PCFs (r s  = - 0.83; p < 0.05). Small-window entropy imaging also performed well in discriminating young and old participants (p < 0.05) and postmenopausal women with low versus moderate-to-high osteoporosis risk (the area under the ROC curve = 0.80; cut-off value = 2.65; accuracy = 86.00%; sensitivity = 71.43%; specificity = 88.37%). Ultrasound small-window entropy imaging has great potential in bone tissue characterization and osteoporosis assessment., (© 2022. The Author(s).)

Sketches in existing large-scale datasets like the recent QuickDraw collection are often stored in a vector format, with strokes consisting of sequentially sampled points. However, most existing sketch recognition methods rasterize vector sketches as binary images and then adopt image classification techniques. In this article, we propose a novel end-to-end single-branch network architecture RNN-Rasterization-CNN (Sketch-R2CNN for short) to fully leverage the vector format of sketches for recognition. Sketch-R2CNN takes a vector sketch as input and uses an RNN for extracting per-point features in the vector space. We then develop a neural line rasterization module to convert the vector sketch and the per-point features to multi-channel point feature maps, which are subsequently fed to a CNN for extracting convolutional features in the pixel space. Our neural line rasterization module is designed in a differentiable way for end-to-end learning. We perform experiments on existing large-scale sketch recognition datasets and show that the RNN-Rasterization design brings consistent improvement over CNN baselines and that Sketch-R2CNN substantially outperforms the state-of-the-art methods.

Background: Androgen deprivation therapy (ADT) suppresses the production of androgen, and ADT is broadly used for intermediate or higher risk disease including advanced and metastatic cancer. ADT is associated with numerous adverse effects derived from the pharmacological properties. Previous meta-analysis on fracture risk among ADT users possessed limited data without further subgroup analysis. Risk estimation of updated real-world evidence on ADT-related fracture remains unknown. Objectives: To assess the risk of fracture and fracture requiring hospitalization associated with ADT among prostate cancer population on different disease conditions, treatment regimen, dosage level, fracture sites. Methods: The Cochrane Library, PubMed, and Embase databases were systematically screened for eligible cohort studies published from inception to March 2020. Two authors independently reviewed all the included studies. The risks of any fracture and of fracture requiring hospitalization were assessed using a random-effects model, following by leave-one-out, stratified, and sensitivity analyses. The Grading of Recommendations Assessments, Development and Evaluations (GRADE) system was used to grade the certainty of evidence. Results: Sixteen eligible studies were included, and total population was 519,168 men. ADT use is associated with increasing fracture risk (OR, 1.39; 95% CI, 1.26-1.52) and fracture requiring hospitalization (OR, 1.55; 95% CI, 1.29-1.88). Stratified analysis revealed that high-dose ADT results in an elevated risk of fracture with little statistical heterogeneity, whereas sensitivity analysis restricted to adjust for additional factors indicated increased fracture risks for patients with unknown stage prostate cancer or with no restriction on age with minimal heterogeneity. The GRADE level of evidence was moderate for any fracture and low for fracture requiring hospitalization. Conclusion: Cumulative evidence supports the association of elevated fracture risk with ADT among patients with prostate cancer, including those with different disease conditions, treatment regimens, dose levels, and fracture sites. Further prospective trials with intact information on potential risk factors on fracture under ADT use are warranted to identify the risky population., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2021 Wu, Chen, Wang, Tsai, Wang, Tai, Luo, Wang and Chen.)

Electron work function (EWF) has demonstrated its great promise in materials analysis and design, particularly for single-phase materials, e.g., solute selection for optimal solid-solution strengthening. Such promise is attributed to the correlation of EWF with the atomic bonding and stability, which largely determines material properties. However, engineering materials generally consist of multiple phases. Whether or not the overall EWF of a complex multi-phase material can reflect its properties is unclear. Through investigation on the relationships among EWF, microstructure, mechanical and electrochemical properties of low-carbon steel samples with two-level microstructural inhomogeneity, we demonstrate that the overall EWF does carry the information on integrated electron behavior and overall properties of multiphase alloys. This study makes it achievable to develop "electronic metallurgy"-an electronic based novel alternative methodology for materials design.

Specifying precise relationships among graphic elements is often a time-consuming process with traditional alignment tools. Automatic beautification of roughly designed layouts can provide a more efficient solution but often lead to undesired results due to ambiguity problems. To facilitate ambiguity resolution in layout beautification, we present a novel user interface for visualizing and editing inferred relationships through an automatic global layout beautification process. First, our interface provides a preview of the beautified layout with inferred constraints without directly modifying an input layout. In this way, the user can easily keep refining beautification results by interactively repositioning and/or resizing elements in the input layout. Second, we present a gestural interface for editing automatically inferred constraints by directly interacting with the visualized constraints via simple gestures. Our technique is applicable to both 2D and 3D global layout beautification, supported by efficient system implementation that provides instant user feedback. Our user study validates that our tool is capable of creating, editing, and refining layouts of graphic elements, and is significantly faster than the standard snap-dragging or command-based alignment tools for both 2D and 3D layout tasks.

Screw loosening due to broken pedicles is a common complication resulting from the insertion of screws either with inadequate diameters or into an osteoporotic pedicle. In this novel in vitro study, we tried to clarify the contribution of the pedicle to screw fixation and subsequent salvage strategies using longer or larger-diameter screws in broken pedicles. Sixty L4 fresh-frozen lumbar vertebrae harvested from mature pigs were designed as the normal-density group (n = 30) and decalcified as the osteoporosis group (n = 30). Three modalities were randomly assigned as intact pedicle (n = 30), semi-pedicle (n = 15), and non-pedicle (n = 15) in each group. Three sizes of polyaxial screws (diameter × length of 6.0 mm × 45 mm, 6.0 mm × 50 mm, and 6.5 mm × 45 mm) over five trials were used in each modality. The associations between bone density, pedicle modality and screw pullout strength were analyzed. After decalcification for 4 weeks, the area bone mineral density decreased to approximately 56% (p < 0.05) of the normal-density group, which was assigned as the osteoporosis group. An appropriate screw trajectory and insertional depth were confirmed using X-ray imaging prior to pullout testing in both groups. The pullout forces of larger-diameter screws (6.5 mm × 45 mm) and longer screws (6.0 mm × 50 mm) were significantly higher (p < 0.05) in the semi- and non-pedicle modalities in the normal-density group, whereas only longer screws (6.0 mm × 50 mm) had a significantly higher (p < 0.05) pullout force in the non-pedicle modalities in the osteoporosis group. The pedicle plays an important role in both the normal bone density group and the osteoporosis group, as revealed by analyzing the pullout force percentage contributed by the pedicle. Use of a longer screw would be a way to salvage a broken pedicle of osteoporotic vertebra.

Rationale: Anxiety is a mediator for emotional reactivity and acute blood pressure elevations, which are associated with an increased risk of cardiovascular death. Alprazolam is a common medication for anxiolysis. We hypothesized that alprazolam usage can reduce the risk of major adverse cardiovascular events (MACEs) in patients with hypertension., Methods: A retrospective cohort study was performed using datasets from Taiwanese Health and Welfare Data. Patients with hypertension were divided into exposed (Alprazolam-exposed) and control groups (non-Alprazolam-exposed) with 1:1 propensity score matching. The study endpoint was the occurrence of MACE. Adjusted hazard ratio (aHR) of MACE risk was estimated using the multiple Cox proportional hazard model. Age-stratified analysis was performed to evaluate the interaction of age and alprazolam use with MACEs., Results: The study cohort consisted of 335 517 alprazolam-exposed patients and 1:1 PSM controls. The mean age was 63.62 ± 12.71 years in the Alprazolam-exposed population. Alprazolam exposure was significantly associated with reduced risk of MACEs (aHR = 0.965, 95% CI = 0.954-0.977), including ischemic stroke (aHR = 0.958, 95% CI = 0.940-0.976), hemorrhagic stroke (aHR = 0.856, 95% CI = 0.821-0.892), myocardial infarction (aHR = 0.933, 95% CI = 0.900-0.968), sudden cardiac death (aHR = 0.955, 95% CI = 0.916-0.996), and all-cause mortality (aHR = 0.921, 95% CI = 0.909-0.932). In the age-subgroup analysis, alprazolam showed the greatest risk reduction effect in hemorrhagic stroke for patients aged <65 years (aHR = 0.779, 95% CI = 0.727-0.835)., Conclusion: Alprazolam usage in patients with hypertension was associated with a slightly reduced risk of MACEs and all-cause mortality, and up to 22% reduced risk of hemorrhagic stroke was observed in alprazolam users aged <65 years., (© 2019 John Wiley & Sons, Ltd.)

Pedicle screw loosening resulting from insufficient bone-screw interfacial holding power is not uncommon. The screw shape and thread profile are considered important factors of the screw fixation strength. This work investigated the difference in pullout strength between conical and cylindrical screws with three different thread designs. The effects of the thread profiles on the screw fixation strength of cannulated screws with or without cement augmentation in osteoporotic bone were also evaluated. Commercially available artificial standard L4 vertebrae and low-density polyurethane foam blocks were used as substitutes for healthy vertebrae and osteoporotic bones, respectively. The screw pullout strengths of nine screw systems were investigated (six in each). These systems included the combination of three different screw shapes (solid/cylindrical, solid/conical and cannulated/cylindrical) with three different thread profiles (fine-thread, coarse-thread and dual-core/dual-thread). Solid screws were designed for the cementless screw fixation of vertebrae using the standard samples, whereas cannulated screws were designed for the cemented screw fixation of osteoporotic bone using low-density test blocks. Following specimen preparation, a screw pullout test was conducted using a material test machine, and the maximal screw pullout strength was compared among the groups. This study demonstrated that, in healthy vertebrae, both the conical and dual-core/dual-thread designs can improve pullout strength. A combination of the conical and dual-core/dual-thread designs may achieve optimal postoperative screw stability. However, in osteoporotic bone, the thread profile have little impact on the screw fixation strength when pedicle screws are fixed with cement augmentation. Cement augmentation is the most important factor contributing to screw pullout fixation strength as compared to screw designs., Competing Interests: The authors have declared that no competing interests exist.

We present a novel 3D model-guided interface for in-situ sketching on 3D planes. Our work is motivated by evolutionary design, where existing 3D objects form the basis for conceptual re-design or further design exploration. We contribute a novel workflow that exploits the geometry of an underlying 3D model to infer 3D planes on which 2D strokes drawn that are on and around the 3D model should be meaningfully projected. This provides users with the nearly modeless fluidity of a sketching interface, and is particularly useful for 3D sketching over planes that are not easily accessible or do not preexist. We also provide an additional set of tools, including sketching with explicit plane selection and model-aware canvas manipulation. Our system is evaluated with a user study, showing that our technique is easy to learn and effective for rapid sketching of product design variations around existing 3D models.

Organic-inorganic perovskite nanocrystals with excellent optoelectronic properties have been utilized in various applications, despite their stability issues. The perovskite materials are sensitive to environments such as polar solvents, moisture, and heat. Thus, they are not used for extrusion three-dimensional (3D) printing, as it is usually conducted in the ambient environment and requires heating to liquefy the printed materials. In this work, 11 thermoplastic polymers conventionally used for extrusion 3D printing were investigated to test their capability as protective encapsulation materials for perovskite nanocrystals. Three of them exhibited good protective properties, and one (polycaprolactone, PCL) of these three could be blended with perovskite nanocrystals to form perovskite nanocrystal-PCL composites, which were deformable and stretchable once heated. Because of the low melting point of PCL, the perovskite nanocrystals maintained their optical properties after 3D printing, and the printed objects were still having fluorescent behavior. Moreover, fluorescent micrometer-sized fibers based on the perovskite nanocrystal-PCL composites could also be simply prepared using cotton candy makers. Perovskite nanocrystal-PCL composite films with different emission wavelengths were incorporated with blue light-emitting diodes (LEDs) to realize white LEDs with Commission Internationale de l'Éclairage chromaticity coordinates of (0.33, 0.33).

Pedicles are often broken when screws are inserted into hard pedicles with small diameters or when the diameter of the screw itself is inadequate. However, there is a lack of biomechanical literature that addresses screw loosening as a result of broken pedicles or the resulting salvage of those screws. We performed a novel in vitro study to compare the pullout strength of screws between intact pedicles and two different types of broken pedicles; strategies to prevent screw loosening were also compared. Thirty L4 Sawbones were designed to represent intact pedicles, semi-pedicles, and nonpedicles and were prepared for screw insertion. Three sizes of polyaxial screws (diameter × length dimensions of 6.0 mm × 45 mm, 6.0 mm × 50 mm and 6.5 mm × 45 mm) were independently and randomly distributed into the intact-pedicle group (IP group, n = 30), the semi-pedicle group (SP group, n = 15), or the nonpedicle group (NP group, n = 15). The experiments were conducted across a minimum of five trials for each of the chosen screw sizes. We then analyzed the results of the imaging, pullout testing, and embedded bone volume. Any fractures or defects of the vertebrae caused by screw insertion were excluded from the study. The appropriate screw trajectory and insertional depth were confirmed using axial and sagittal X-ray imaging prior to screw pullout testing. A pullout strength of only 41% to 45% for the SP group and 29% to 39% for the NP group was retained following a broken pedicle. The use of longer or larger-diameter screws appears to be an effective salvaging procedure for the NP group (p < 0.05). The embedded bone volume percentage analysis indicated that, compared to the IP group, 68% to 76% of effective bone embedded into the screw threads in the SP group, and 58% to 65% in the NP group. There was no direct correlation between the pullout strength and the embedded bone volume; however, less effective embedded bone volume was associated with lower pullout strength. This study describes the evolution of the well-established screw pullout test being applied to the broken pedicle Sawbone testing model. The pedicle plays an important role in determining the pullout strength of a screw. However, a salvage procedure that utilizes a longer or larger-diameter screw might be a reliable clinical approach to address broken pedicles., Competing Interests: The authors have declared that no competing interests exist.

We present a simple and efficient method based on deep learning to automatically decompose sketched objects into semantically valid parts. We train a deep neural network to transfer existing segmentations and labelings from three-dimensional (3-D) models to freehand sketches without requiring numerous well-annotated sketches as training data. The network takes the binary image of a sketched object as input and produces a corresponding segmentation map with per-pixel labelings as output. A subsequent postprocess procedure with multilabel graph cuts further refines the segmentation and labeling result. We validate our proposed method on two sketch datasets. Experiments show that our method outperforms the state-of-the-art method in terms of segmentation and labeling accuracy and is significantly faster, enabling further integration in interactive drawing systems. We demonstrate the efficiency of our method in a sketch-based modeling application that automatically transforms input sketches into 3-D models by part assembly.

Previous studies examining the other-race effect in school-age children mostly focused on recognition memory performance. Here we investigated perceptual discriminability for Asian-like versus Caucasian-like morph faces in school-age Taiwanese children and adults. One-hundred-and-two 5- to 12-year-old children and twenty-three adults performed a sequential same/different face matching task, where they viewed an Asian- or a Caucasian-parent face followed by either the same parent face or a different morphed face (containing 15%, 30%, 45%, or 60% contribution from the other parent face) and judged if the two faces looked the same. We computed the d' as the sensitivity index for each age groups. We also analyzed the group mean rejection rates as a function of the morph level and fitted with a cumulative normal distribution function. Results showed that the adults and the oldest 11-12-year-old children exhibited a greater sensitivity (d') and a smaller discrimination threshold (μ) in the Asian-parent condition than those in the Caucasian-parent condition, indicating the presence of an own-race advantage. On the contrary, 5- to 10-year-old children showed an equal sensitivity and similar discrimination thresholds for both conditions, indicating an absence of the own-race advantage. Moreover, a gradual development in enhancing the discriminability for the Asian-parent condition was observed from age 5 to 12; however, the progression in the Caucasian-parent condition was less apparent. In sum, our findings suggest that expertise in face processing may take the entire childhood to develop, and supports the perceptual learning view of the other-race effect-the own-race advantage seen in adulthood likely reflects a result of prolonged learning specific to faces most commonly seen in one's visual environment such as own-race faces.