Search

The self-passivating yttrium-containing WCr alloy has been developed and researched as a potential plasma-facing armour material for fusion power plants. This study explores the use of yttria (Y2O3) powders instead of yttrium elemental powders in the mechanical alloying process to assess their applicability for this material. Fabricated through field-assisted sintering, WCr-Y2O3 ingots show Y2O3 and Cr-containing oxides (Cr-O and Y-Cr-O) dispersed at grain boundaries (GBs), while WCrY ingots contain Y-O particles at grain boundaries, both resulting from unavoidable oxidation during fabrication. WCr-Y2O3 demonstrates higher flexural strength than WCrY across all temperature ranges, ranging from 850 to 1050 MPa, but lower fracture toughness, between 3 and 4 MPa·√m. Enhanced oxidation resistance is observed in WCr-Y2O3, with lower mass gain as compared to WCrY during the 20-hour oxidation test. This study confirms the effectiveness of both yttria and yttrium in the reactive element effect (REE) for the passivation of WCr alloy, suggesting the potential of Y2O3-doped WCr for first wall applications in a fusion power plant. [ABSTRACT FROM AUTHOR]

Developing new materials to be applied in extreme environments is an opportunity and a challenge for the future. High entropy alloys are new materials that seem promising approaches to work in nuclear fusion reactors. In this work, FeTaTiVW high entropy alloys were developed and characterized with Molecular Dynamic and Hybrid Molecular Dynamic Monte Carlo simulations. The simulation results show that phase separation originates a lower potential energy per atom and a high level of segregation compared to those of a uniform solid solution. Moreover, the experimental diffractogram of the milled powder shows the formation of a body-centred cubic-type structure and the presence of TiO2. In addition, the microstructure of the consolidated material evidenced three phases: W-rich, Ti-rich, and a phase with all the elements. This phase separation observed in the microstructure agrees with the Hybrid Molecular Dynamic Monte Carlo simulation. Moreover, the consolidated material's thermal conductivity and specific heat are almost constant from 25 °C to 1000 °C, and linear expansion increases with increasing temperature. On the other hand, specific heat and thermal expansion values are in between CuCrZr and W values (materials chosen for the reactor walls). The FeTaTiVW high entropy alloy evidences a ductile behaviour at 1000 °C. Therefore, the promising thermal properties of this system can be attributed to the multiple phases and systems with different compositions of the same elements, which is exciting for future developments. [ABSTRACT FROM AUTHOR]

To enable the development of artificial intelligence of things, the improvement of the strain sensing mechanisms and optimization of the interconnections are needed. Direct laser writing to obtain laser-induced graphene (LIG) is being studied as a promising technique for producing wearable, lightweight, highly sensitive, and reliable strain sensors. These devices show a higher degree of flexibility and stretchability when transferred to an elastomeric substrate. In this article, we manufactured polydimethylsiloxane (PDMS)-encapsulated LIG piezoresistive strain sensors with a quasi-linear behavior and a gauge factor of 111. The produced LIG was morphologically characterized via Raman spectroscopy and scanning electron microscopy before and after the electromechanical characterization and before and after the LIG transfer to PDMS. The results from these analyses revealed that the integrity of the material after the test was not affected and that the LIG volume in contact with the substrate increased after transfer and encapsulation in PDMS, leading to the improvement of the sensor performance. The sensors' capability for measuring bend angles accurately was demonstrated experimentally, making them useable in a wide range of applications for human body movement monitoring as well as for structural health monitoring. Regarding body monitoring, a PDMS-encapsulated LIG sensor for knee bending angle detection was proposed. This device showed unaffected performance of 1500 cycles under 8% uniaxial deformation and with response times in the range of 1-2 s., Competing Interests: The authors declare no competing financial interest., (© 2024 The Authors. Published by American Chemical Society.)