Search

Pantograph arcing in ac traction system generates transients, and causes asymmetries and distortion in supply voltage and current waveforms. These asymmetric voltage and current lead to a net dc component and harmonics that propagate within the traction power and signalling system and cause electromagnetic interference. This problem is enhanced during winter because of the layer of ice/snow on the overhead contact wire. The sliding contact becomes poor and a visible arc moves along with the pantograph. In this paper, it is shown how different parameters like traction current, line speed, power factor, and supply voltage influence the arcing, its characteristics, and the dc components. It is shown that the dc current component increases with increasing train speed and traction current, and reduces at a lower power factor. It is also discussed how the presence of an ice layer influences the arcing and the dc components. It is found that running the trains below the normal operating power factors is an effective choice to mitigate this problem. The findings presented in this paper could be beneficial to estimate the probable limit of the dc component at the planning stage so that proper precautions can be taken at the design stage itself.

Pantograph arcing is a common phenomenon in electrified railway systems. This is also a source of broadband-conducted and radiated electromagnetic interference (EMI) for vehicle as well as traction power and signaling systems. In this paper and the companion paper, experimental analyses of pantograph arcing phenomena are presented for dc and ac feeding systems, respectively. Influences of different parameters on dc traction system, such as supply-voltage polarity, relative motion between pantograph and overhead contact wire, namely, forward motion along the track (longitudinal), and lateral sliding motion of the pantograph (zigzag) are presented here. From the voltage and current waveforms of the test runs, it is shown that pantograph arcing is a polarity-dependent phenomenon. For the positive-fed overhead traction system, where pantograph is cathode, the supply interruptions due to zigzag motion are comparatively less compared to negatively fed traction systems. As a result, the transients, due to pantograph arcing, are more frequent in negatively fed traction systems. It is found that the arc root movement along the electrode surfaces (pantograph-contact wire) is governed by the relative motion and polarity of the electrodes. The analyses presented in this paper also form a foundation to understand the pantograph arcing process and the corresponding influential parameters with the ac supply presented in the companion paper. The findings presented in this paper could be beneficial for coming up with appropriate mitigation techniques from the EMI due to pantograph arcing in dc-fed traction systems.

This paper presents an optimization model for simulations of railway power supply systems. It includes detailed power systems modeling, train movements in discretized time considering running resistance and other mechanical constraints, and the voltage-drop-induced reduction of possible train tractive forces. The model has a fixed number of stationary power system nodes, which alleviates optimized operation overtime. The proposed model uses SOS2 (Special Ordered Sets of type 2) variables to distribute the train loads to the two most adjacent power system nodes available. The impacts of the number of power system nodes along the contact line and the discretized time step length on model accuracy and computation times are investigated. The program is implemented in GAMS. Experiences from various solver choices are also discussed. The train traveling times are minimized in the example. Other studies could e.g. consider energy consumption minimization. The numerical example is representative for a Swedish decentralized, rotary-converter fed railway power supply system. The proposed concept is however generalizable and could be applied for all kinds of moving load power system studies. QC 20130610. Updated from submitted to published.

Railways are the most energy-efficient land-based mode of transport, and electrification is the most energy-efficient way to power the trains. There are many existing solutions to supply the trains with electricity. Regardless of which particular technology is chosen, it is beneficial to interconnect the public power grids to grids supplying power to the railways. This paper shows that the most efficient, flexible, and gentle-for-the-public-grid way of doing that is through power electronic-based power converters. Converters offer great benefits regardless of whether the overhead contact lines are of DC-type or AC type, and regardless of the AC grid frequency. This paper presents neither new theory nor new experimental results. Based on already available information, this paper presents logical arguments leading to this conclusion from collected facts. Over time what used to be advanced and high-cost equipment earlier can nowadays be purchased at reasonable cost. It is obvious that for most electrically-fed railways, the use of modern power converters is attractive. Where the individual trains are high consumers of energy, the railway gradients are substantial, and the public grids feeding the railway are weak, the use of converters would be technically desirable, if not necessary for electrification.It is expected that more high-speed railways will be built, and more existing railways will be electrified in the foreseeable future. This paper could provide some insights to infrastructure owners and decision makers in railway administrations about value additions that converter-fed electric railways would provide. QC 20120926

One of the most common and yet unavoidable problems in electrified railways are because of pantograph arcing. The intensity of arcing increases during winter because of the ice layer on the overhead contact wire. In AC traction system, pantograph arcing distorts the sinusoidal waveforms of the supply voltage and current. It also generates transients at the current zero crossings (CZC). All these result in a net DC component, harmonics and radiated emission. In this paper we will present an experimental investigation to understand pantograph arcing and influence of power factor on conducted and radiated emission. We found that pantograph arcing generates both conducted and radiated emission in a wide band, starting from DC. Both the DC component and higher order conducted and radiated emission increases with line speed. Running the train at lower power factor can reduce the DC component and emerging as the most preferred solution against problems due to ice in cold weather.

The most common and yet unavoidable EMC problems with electrified railways are due to pantograph arcing. This distorts the waveform of the supply voltage and current, can generates transients during the zero crossings of the current and can cause interference with the traction power and signalling system. Pantograph arcing is a complex phenomenon and depends on speed of the train, current, presence of inductance etc. In a sliding contact like pantograph and contact wire, the arc root moves across both electrodes because of the relative motion between them. In this paper, we will present an experimental analyses of the arc root movement and influence of different parameters on it using a laboratory setup.