Search

The mechanical competence and suturing ability of collagen-based membranes are paramount in Guided Bone Regeneration (GBR) therapy, to ensure damage-free implantation, fixation and space maintenance in vivo. However, contact with the biological medium can induce swelling of collagen molecules, yielding risks of membrane sinking into the bone defect, early loss of barrier function, and irreversibly compromised clinical outcomes. To address these challenges, this study investigates the effect of the crosslinked network architecture on both mechanical and suture-holding properties of a new atelocollagen (AC) membrane. UV-cured networks were obtained via either single functionalisation of AC with 4-vinylbenzyl chloride (4VBC) or sequential functionalisation of AC with both 4VBC and methacrylic anhydride (MA). The wet-state compression modulus (Ec), Atomic Force Microscopy elastic modulus (EAFM) and swelling ratio (SR) were significantly affected by the UV-cured network architecture, leading up to a three-fold reduction in SR, and about two-fold increase in both Ec and EAFM, in the sequentially functionalised, compared to the single-functionalised, samples. Electron microscopy, dimensional analysis and compression testing revealed the direct impact of the ethanol series dehydration process on membrane microstructure, yielding densification of the freshly synthesised porous samples and a pore-free microstructure with increased Ec. Noteworthy, the single-functionalised, but not the sequentially functionalised, samples displayed higher suture retention strength in both the dry state and following 1 hour in Phosphate Buffered Saline (PBS), compared to Bio-Gide(r). These structure-property relationships confirm the key role played by the molecular architecture of covalently crosslinked collagen, aimed towards long-lasting resorbable membranes for predictable GBR., Comment: 40 pages, 9 figures, 1 Table. Accepted in Biomaterials Materials

Implantable hydrogels should ideally possess mechanical properties matched to the surrounding tissues to enable adequate mechanical function while regeneration occurs. This can be challenging, especially when degradable systems with high water content and hydrolysable chemical bonds are required in anatomical sites under constant mechanical stimulation, e.g. a foot ulcer cavity. In these circumstances, the design of hydrogel composites is a promising strategy to provide controlled structural features and macroscopic properties over time. To explore this strategy, the synthesis of a new photocurable elastomeric polymer, poly(glycerol-co-sebacic acid-co-lactic acid-co-polyethylene glycol) acrylate (PGSLPA), is investigated, along with its processing into UV-cured hydrogels, electrospun nonwovens and fibre-reinforced variants, without the need for a high temperature curing step or use of hazardous solvents. The mechanical properties of bioresorbable PGSLPA hydrogels were studied with and without electrospun nonwoven reinforcement and with varied layered configurations, aiming to determine the effects of microstructure on bulk compressive strength and elasticity. The nonwoven reinforced PGSLPA hydrogels exhibited a 60 % increase in compressive strength and an 80 % increase in elastic moduli compared to fibre-free PGSLPA samples. Mechanical properties of the fibre-reinforced hydrogels could also be modulated by altering the layering arrangement of the nonwoven and hydrogel phase. The nanofibre reinforced PGSLPA hydrogels also exhibited good elastic recovery, as evidenced by hysteresis in compression fatigue stress-strain evaluations showing a return to original dimensions., Comment: 26 pages, 12 figures, 3 tables. Accepted in Polymers

UV-cured collagen-based hydrogels hold promise in skeletal muscle regeneration due to their soft elastic properties and porous architecture. However, the complex triple helix conformation of collagen and environmental conditions, i.e. molecular oxygen, pose risks to reaction controllability, wet-state integrity and reproducibility. To address this challenge, a photo-click hydrogel platform is presented through an oxygen-insensitive thiol-ene reaction between 2-iminothiolane (2IT)-functionalized type I collagen and multi-arm, non-homopolymerizable norbornene-terminated polyethylene glycol (PEG). UV-induced network formation is demonstrated by oscillatory time sweeps on the reacting thiol-ene mixture, so that significantly increased storage moduli are measured and adjusted depending on the photo-initiator concentration. Variations in PEG functionality (4-arm and 8-arm) and PEG content generate hydrogels with skeletal muscle native stiffness (Ec= 1.3-11.5 kPa), diffusion-controlled swelling behavior and erosion-driven degradability. In vitro, no cytotoxic effect is detected on C2C12 murine myoblasts, while myogenic differentiation is successfully accomplished on hydrogel-seeded cells in low serum culture medium. In vivo, 7-day subcutaneous implantation of selected thiol-ene hydrogel in rats reveal higher cell infiltration, blood vessel formation, and denser tissue interface compared to a clinical gold standard collagen matrix (Mucograft, Geistlich). These results therefore support the applicability and further development of this hydrogel platform for skeletal muscle regeneration., Comment: 10 figures, 1 table; accepted in Macromolecular Materials and Engineering

Continuous wound monitoring is one strategy to minimise infection severity and inform prompt variations in therapeutic care following infection diagnosis. However, integration of this functionality in therapeutic wound dressings is still challenging. We hypothesised that a theranostic dressing could be realised by integrating a collagen-based wound contact layer with previously demonstrated wound healing capability, and a halochromic dye, i.e. bromothymol blue (BTB), undergoing colour change following infection-associated pH changes (pH: 5-6 --> >7). Two different BTB integration strategies, i.e. electrospinning and drop-casting, were pursued to introduce long-lasting visual infection detection capability through retention of BTB within the dressing. Both systems had an average BTB loading efficiency of 99 wt.% and displayed a colour change within one minute of contact with simulated wound fluid. Drop-cast samples retained up to 85 wt.% of BTB after 96 hours in a near-infected wound environment, in contrast to the fibre-bearing prototypes, which released over 80 wt.% of BTB over the same time period. An increase in collagen denaturation temperature (DSC) and red shifts (ATR-FTIR) suggests the formation of secondary interactions between the collagen-based hydrogel and the BTB, which are attributed to count for the long-lasting dye confinement and durable dressing colour change. Given the high L929 fibroblast viability in drop-cast sample extracts (92%, 7 days), the presented multiscale design is simple, cell- and regulatory-friendly, and compliant with industrial scale-up. This design, therefore, offers a new platform for the development of theranostic dressings enabling accelerated wound healing and prompt infection diagnosis., Comment: 21 pages, 9 figures, 1 table; accepted in International Journal of Biological Macromolecules

The tissue source of type I collagen is critical to ensure scalability and regulation-friendly clinical translation of new medical device prototypes. However, the selection of a commercial source of collagen that fulfils both aforementioned requirements and is compliant with new manufacturing routes is challenging. This study investigates the effect that type I collagen extracted from three different mammalian tissues has on the molecular and macroscopic characteristics of a new UV-cured collagen hydrogel. Pepsin-solubilised bovine atelocollagen (BA) and pepsin-solubilised porcine atelocollagen (PA) were selected as commercially available raw materials associated with varying safety risks and compared with in-house acid-extracted type I collagen from rat tails (CRT). All raw materials displayed the typical dichroic and electrophoretic characteristics of type I collagen, while significantly decreased lysine content was measured on samples of PA. Following covalent functionalisation with 4-vinylbenzyl chloride (4VBC), BA and CRT products generated comparable UV-cured hydrogels with significantly increased averaged gel content (G > 97 wt.%), while the porcine variants revealed the highest swelling ratio (SR = 2224 +/- 242 wt.%) and an order of magnitude reduction in compression modulus (Ec = 6 +/- 2 kPa). Collectively, these results support the use of bovine tissues as a chemically viable source of type I collagen for the realisation of UV-cured hydrogels with competitive mechanical properties and covalent network architectures., Comment: Accepted in Prosthesis, 21 pages, 7 pages, 2 tables

The fast degradation of collagen-based membranes in the biological environment remains a critical challenge, resulting in underperforming Guided Bone Regeneration (GBR) therapy leading to compromised clinical results. Photoactive atelocollagen (AC) systems functionalised with ethylenically unsaturated monomers, such as 4-vinylbenzyl chloride (4VBC), have been shown to generate mechanically competent materials for wound healing, inflammation control and drug delivery, whereby control of the molecular architecture of the AC network is key. Building on this platform, the sequential functionalisation with 4VBC and methacrylic anhydride (MA) was hypothesised to generate UV-cured AC hydrogels with reduced swelling ratio, increased proteolytic stability and barrier functionality for GBR therapy. The sequentially functionalised atelocollagen precursor (SAP) was characterised via TNBS and ninhydrin colourimetric assays, circular dichroism and UV-curing rheometry, which confirmed nearly complete consumption of collagen primary amino groups, preserved triple helices and fast (within 180 s) gelation kinetics, respectively. Hydrogel swelling ratio and compression modulus were adjusted depending on the aqueous environment used for UV-curing, whilst the sequential functionalisation of AC successfully generated hydrogels with superior proteolytic stability in vitro compared to both 4VBC functionalised control and the commercial dental membrane Bio-Gide. These in vitro results were confirmed in vivo via both subcutaneous implantation and a proof-of-concept study in a GBR calvarial model, indicating integrity of the hydrogel and barrier defect, as well as tissue formation following 1-month implantation in rats., Comment: 11 figures, 2 tables, accepted on Acta Biomaterialia

Regulating the activity of matrix metalloproteinases (MMPs) is a potential strategy for osteoarthritis (OA) therapy, although delivering this effect in a spatially and temporally localised fashion remains a challenge. Here, we report an injectable and self-healing hydrogel enabling factor-free MMP regulation and biomechanical competence in situ. The hydrogel is realised within one minute upon room temperature coordination between hyaluronic acid (HA) and a cell-friendly iron-glutathione complex in aqueous environment. The resultant gel displayed up to 300% in shear strain and tolerance towards ATDC 5 chondrocytes, in line with the elasticity and biocompatibility requirements for connective tissue application. Significantly enhanced inhibition of MMP-13 activity was achieved after 12 hours in vitro, compared with a commercial HA injection (OSTENIL PLUS). Noteworthy, 24-hour incubation of a clinical synovial fluid sample collected from a late-stage OA patient with the reported hydrogel was still shown to downregulate synovial fluid MMP activity (100.0 +/- 17.6 % --> 81.0 +/- 7.5 %), with at least comparable extent to the case of the OSTENIL PLUS-treated SF group (100.0 +/- 17.6 % --> 92.3 +/- 27.3 %). These results therefore open up new possibilities in the use of HA as both mechanically-competent hydrogel as well as a mediator of MMP regulation for OA therapy.

The creation of hyaluronic acid (HA)-based materials as biomineralisation scaffolds for cost-effective hard tissue regenerative therapies remains a key biomedical challenge. A non-toxic and simple acellular method to generate specific hydrogen phosphate interactions within the polymer network of cystamine-crosslinked HA hydrogels is reported. Reinforced dual crosslinked hydrogel networks were accomplished after 4-week incubation in disodium phosphate-supplemented solutions that notably enabled the mineralisation of hydroxyapatite (HAp) crystals across the entire hydrogel structure. Hydrogen phosphate-cystamine crosslinked HA hydrogen bond interactions were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and density functional theory (DFT) calculations. Hydrogen phosphate-mediated physical crosslinks proved to serve as a first nucleation step for acellular hydrogel mineralisation in simulated body fluid allowing HAp crystals to be detected by X-ray powder diffraction (2{\theta} = 27{\deg}, 33{\deg} and 35{\deg}) and visualised with density gradient across the entire hydrogel network. On a cellular level, the presence of aggregated structures proved key to inducing ATDC 5 cell migration whilst no toxic response was observed after 3-week culture. This mild and facile ion-mediated stabilisation of HA-based hydrogels has significant potential for accelerated hard tissue repair in vivo and provides a new perspective in the design of dual crosslinked mechanically competent hydrogels.

The current management of critical size bone defects (CSBDs) remains challenging and requires multiple surgeries. To reduce the number of surgeries, wrapping a biodegradable fibrous membrane around the defect to contain the graft and carry biological stimulants for repair is highly desirable. Poly(epsilon-caprolactone) (PCL) can be utilised to realise nonwoven fibrous barrier-like structures through free surface electrospinning (FSE). Human periosteum and induced membrane (IM) samples informed the development of an FSE membrane to support platelet lysate (PL) absorption, multipotential stromal cells (MSC) growth, and the prevention of cell migration. Although thinner than IM, periosteum presented a more mature vascular system with a significantly larger blood vessel diameter. The electrospun membrane (PCL3%-E) exhibited randomly configured nanoscale fibres that were successfully customised to introduce pores of increased diameter, without compromising tensile properties. Additional to the PL absorption and release capabilities needed for MSC attraction and growth, PCL3%-E also provided a favourable surface for the proliferation and alignment of periosteum- and bone marrow derived-MSCs, whilst possessing a barrier function to cell migration. These results demonstrate the development of a promising biodegradable barrier membrane enabling PL release and MSC colonisation, two key functionalities needed for the in situ formation of a transitional periosteum-like structure, enabling movement towards single-surgery CSBD reconstruction.

Photodynamically active fibres (PAFs) are a novel class of stimulus-sensitive systems capable of triggering antibiotic-free antibacterial effect on-demand when exposed to light. Despite their relevance in infection control, however, the broad clinical applicability of PAFs has not yet been fully realised due to the limited control in fibrous microstructure, cell tolerance and antibacterial activity in the physiologic environment. We addressed this challenge by creating semicrystalline electrospun fibres with varying content of poly[(L-lactide)-co-(glycolide)] (PLGA), poly(epsilon-caprolactone) (PCL) and methylene blue (MB), whereby the effect of polymer morphology, fibre composition and photosensitiser (PS) uptake on wet state fibre behaviour and functions was studied. The presence of crystalline domains and PS-polymer secondary interactions proved key to accomplishing long-lasting fibrous microstructure, controlled mass loss and controlled MB release profiles (37 degC, pH 7.4, 8 weeks). PAFs with equivalent PLGA:PCL weight ratio successfully promoted attachment and proliferation of L929 cells over a 7-day culture with and without light activation, while triggering up to 2.5 and 4 log reduction in E. coli and S. mutans viability, respectively. These results support the therapeutic applicability of PAFs for frequently encountered bacterial infections, opening up new opportunities in photodynamic fibrous systems with integrated wound healing and infection control capabilities.

Cell-free translational strategies are needed to accelerate the repair of mineralised tissues, particularly large bone defects, using minimally invasive approaches. Regenerative bone scaffolds should ideally mimic aspects of the tissue's ECM over multiple length scales and enable surgical handling and fixation during implantation in vivo. Leveraging the knowledge gained with bioactive self-assembling peptides (SAPs) and SAP-enriched electrospun fibres, we presented a cell free approach for promoting mineralisation via apatite deposition and crystal growth, in vitro, of SAP-enriched nonwoven scaffolds. The nonwoven scaffold was made by electrospinning poly(epsilon-caprolactone) (PCL) in the presence of either peptide P11-4 (Ac-QQRFEWEFEQQ-Am) or P11-8 (Ac-QQRFOWOFEQQ-Am), in light of the polymer's fibre forming capability and its hydrolytic degradability as well as the well-known apatite nucleating capability of SAPs. The 11-residue family of peptides (P11-X) has the ability to self-assemble into beta-sheet ordered structures at the nano-scale and to generate hydrogels at the macroscopic scale, some of which are capable of promoting biomineralisation due to their apatite-nucleating capability. Both variants of SAP-enriched nonwoven used in this study were proven to be biocompatible with murine fibroblasts and supported nucleation and growth of apatite minerals in simulated body fluid (SBF) in vitro. The fibrous nonwoven provided a structurally robust scaffold, with the capability to control SAP release behaviour. Up to 75% of P11-4 and 45% of P11-8 were retained in the fibres after 7-day incubation in aqueous solution at pH 7.4. The encapsulation of SAP in a nonwoven system with apatite-forming as well as localised and long-term SAP delivery capabilities is appealing as a potential means of achieving cost-effective bone repair therapy for critical size defects.

The design of antibacterial-releasing coatings or wrapping materials with controlled drug release capability is a promising strategy to minimise risks of infection and medical device failure in vivo. Collagen fibres have been employed as medical device building block, although they still fail to display controlled release capability, competitive wet-state mechanical properties, and retained triple helix organisation. We investigated this challenge by pursuing a multiscale design approach integrating drug encapsulation, in-situ covalent crosslinking and fibre spinning. By selecting ciprofloxacin (Cip) as a typical antibacterial drug, wet spinning was selected as a triple helix-friendly route towards Cip-encapsulated collagen fibres; whilst in situ crosslinking of fibre-forming triple helices with 1,3 phenylenediacetic acid (Ph) was hypothesised to yield Ph-Cip {\pi}-{\pi} stacking aromatic interactions and enable controlled drug release. Higher tensile modulus and strength were measured in Ph crosslinked fibres compared to state-of-the-art carbodiimide crosslinked controls. Cip-encapsulated Ph-crosslinked fibres revealed decreased elongation at break and significantly-enhanced drug retention in vitro with respect to Cip-free variants and carbodiimide-crosslinked controls, respectively. This multiscale manufacturing strategy provides new insight aiming at wet spun collagen triple helices with nanoscale-regulated tensile properties and drug release capability.

Polymer-based hydrogels have been widely applied for chronic wound therapeutics, due to their well-acclaimed wound exudate management capability. At the same time, there is still an unmet clinical need for simple wound diagnostic tools to assist clinical decision-making at the point of care and deliver on the vision of patient-personalised wound management. To explore this challenge, we present a one-step synthetic strategy to realise a redox-responsive, hyaluronic acid (HA)-based hydrogel that is sensitive to wound environment-related variations in glutathione (GSH) concentration. By selecting aminoethyl disulfide (AED) as a GSH-sensitive crosslinker and considering GSH concentration variations in active and non-self-healing wounds, we investigated the impact of GSH-induced AED cleavage on hydrogel dimensions, aiming to build GSH-size relationships for potential point-of-care wound diagnosis. The hydrogel was also found to be non-cytotoxic and aided L929 fibroblast growth and proliferation over seven days in vitro. Such a material offers a very low-cost tool for the visual detection of a target analyte that varies dependent on the status of the cells and tissues (wound detection) and may be further exploited as an implant for fibroblast growth and tissue regeneration (wound repair).

Antimicrobial biomaterials are critical to aid in the regeneration of oral soft tissue and prevent or treat localised bacterial infections. With the rising trend in antibiotic resistance, there is a pressing clinical need for new antimicrobial chemistries and biomaterial design approaches enabling on-demand activation of antibiotic-free antimicrobial functionality following an infection that are environment-friendly, flexible and commercially-viable. This study explores the feasibility of integrating a bioresorbable electrospun polymer scaffold with localised antimicrobial photodynamic therapy (aPDT) capability. To enable aPDT, we encapsulated a photosensitiser (PS) in polyester fibres in the PS inert state, so that the antibacterial function would be activated on-demand via a visible light source. Fibrous scaffolds were successfully electrospun from FDA-approved polyesters, either poly(epsilon-caprolactone (PCL) or poly[(rac-lactide)-co-glycolide] (PLGA) with encapsulated PS (either methylene blue (MB) or erythrosin B (ER)). The electrospun fibres achieved an ~100 wt.% loading efficiency of PS, which significantly increased their tensile modulus and reduced their average fibre diameter and pore size with respect to PS-free controls. In vitro, PS release varied between a burst release profile to limited release within 100 hours depending on the selected scaffold formulation. Exposure of PS-encapsulated PCL fibres to visible light successfully led to at least a 1 log reduction in E. coli viability after 60 minutes of light exposure whereas PS-free electrospun controls did not inactive microbes. This study successfully demonstrates the significant potential of PS-encapsulated electrospun fibres as photodynamically active biomaterial for antibiotic-free infection control.

Photoinduced network formation is an attractive strategy for designing water-insoluble gelatin fibres as medical device building blocks and for enabling late-stage property customisation. However, mechanically-competent, long-lasting filaments are still hard to realise with current photoactive, e.g. methacrylated, gelatin systems due to inherent spinning instability and restricted coagulation capability. To explore this challenge, we present a multiscale approach combining the synthesis of 4-vinylbenzyl chloride (4VBC)-functionalised gelatin (Gel-4VBC) with a voltage-free spinning and UV-curing process so that biopolymer networks in the form of either individual fibres or nonwovens could be successfully manufactured. In comparison to state-of-the-art methacrylated gelatin, the mechanical properties of UV-cured Gel-4VBC fibres were readily modulated by adjustment of coagulation conditions, so that an ultimate tensile strength and strain at break of up to ~80 MPa and ~9 % were measured, respectively. The sequential functionalisation /spinning route proved to be highly scalable, so that one step spunlaid formation of fibroblast-friendly nonwoven fabrics was successfully demonstrated with wet spun Gel-4VBC fibres. The presented approach could be exploited to generate a library of gelatin building blocks tuneable from the molecular to the macroscopic level to deliver computer-controlled extrusion of fibres and nonwovens according to defined clinical applications., Comment: 31 oages, 10 Figures, 2 Supplemental Figures, 3 Tables. To appear in Journal of Materials Science

The spread of antimicrobial resistance calls for chronic wound management devices that can engage with the wound exudate and signal infection by prompt visual effects. Here, the manufacture of a two-layer fibrous device with independently-controlled exudate management capability and visual infection responsivity was investigated by sequential free surface electrospinning of poly(methyl methacrylate-co-methacrylic acid) (PMMA-co-MAA) and poly(acrylic acid) (PAA). By selecting wound pH as infection indicator, PMMA-co-MAA fibres were encapsulated with halochromic bromothymol blue (BTB) to trigger colour changes at infection-induced alkaline pH. Likewise, the exudate management capability was integrated via the synthesis of a thermally-crosslinked network in electrospun PAA layer. PMMA-co-MAA fibres revealed high BTB loading efficiency (> 80 wt.%) and demonstrated prompt colour change and selective dye release at infected-like media (pH > 7). The synthesis of the thermally-crosslinked PAA network successfully enabled high water uptake (up to nearly 2500 wt.%) and swelling index (up to nearly 300 a.%), in contrast to electrospun PAA controls. This dual device functionality was lost when the same building blocks were configured in a single-layer mesh of core-shell fibres, whereby significant BTB release (~ 70 wt.%) was measured even at acidic pH. This study therefore demonstrates how the fibrous configuration can be conveniently manipulated to trigger structure-induced functionalities critical to chronic wound management and monitoring., Comment: 2o pages, 9 figures, 2 tables

The covalent functionalisation of type I atelocollagen with either 4-vinylbenzyl or methacrylamide residues is presented as a simple synthetic strategy to achieve customisable, cell-friendly UV-cured hydrogel networks with widespread clinical applicability. Molecular parameters, i.e. the type of monomer, degree of atelocollagen functionalisation and UV curing solution, have been systematically varied and their effect on gelation kinetics, swelling behaviour, elastic properties and enzymatic degradability investigated. UV-cured hydrogel networks deriving from atelocollagen precursors functionalised with equivalent molar content of 4-vinylbenzyl and methacrylamide adducts proved to display remarkably-different swelling ratio, storage modulus and collagenase resistance, similarly to the case of UV-cured hydrogel networks obtained with the same type of methacrylamide adduct, but varied degree of functionalisation. UV-induced network formation of 4VBC functionalised atelocollagen molecules yielded hydrogels with increased stiffness and enzymatic stability, attributed to the molecular rigidity of resulting aromatised crosslinking segment, whilst no toxic response was observed with osteosarcoma G292 cells. Although to a lesser extent, the pH of the UV-curing solution also proved to affect macroscopic hydrogel properties, likely due to the altered organisation of atelocollagen molecules during network formation. By leveraging the knowledge gained with classic synthetic networks, this study highlights how the type of monomer can be conveniently exploited to realise customisable atelocollagen hydrogels with controlled structure-property relationships to meet the requirements of unmet clinical applications., Comment: 10 figures, 2 tables, 3 supplementary figures, Frontiers in Chemistry 2018

Electrospun nanofibrous membranes of natural polymers, such as gelatin, are fundamental in the design of regenerative devices. Crosslinking of electrospun fibres from gelatin is required to prevent dissolution in water, to retain the original nanofibre morphology after immersion in water, and to improve the thermal and mechanical properties, although this is still challenging to accomplish in a controlled fashion. In this study, we have investigated the scalable manufacture and structural stability in aqueous environment of a UV-cured nanofibrous membrane fabricated by free surface electrospinning (FSES) of aqueous solutions containing vinylbenzylated gelatin and poly(epsilon-caprolactone) dimethacrylate (PCL-DMA). Vinylbenzylated gelatin was obtained via chemical functionalisation with photopolymerisable 4-vinylbenzyl chloride (4VBC) groups, so that the gelatin and PCL phase in electrospun fibres were integrated in a covalent UV-cured co-network at the molecular scale, rather than being simply physically mixed. UV-cured nanofibrous membranes did not dissolve in water and showed enhanced thermal and mechanical properties, with respect to as-spun samples, indicating the effectiveness of the photo-crosslinking reaction. In addition, UV-cured gelatin/PCL membranes displayed increased structural stability in water with respect to PCL-free samples and were highly tolerated by G292 osteosarcoma cells. These results therefore support the use of PCL DMA as hydrophobic, biodegradable crosslinker and provide new insight on the scalable design of water insoluble, mechanical competent gelatin membranes for healthcare applications., Comment: 11 Figures, 1 Table, to appear in Materials Science and Engineering C

Chronic wounds fail to proceed through an orderly and timely self healing process, resulting in cutaneous damage with full thickness in depth and leading to a major healthcare and economic burden worldwide. In the UK alone, 200,000 patients suffer from a chronic wound, whilst the global advanced wound care market is expected to reach nearly $11 million in 2022. Despite extensive research efforts so far, clinically-approved chronic wound therapies are still time-consuming, economically unaffordable and present restricted customisation. In this chapter, the role of collagen in the extracellular matrix of biological tissues and wound healing will be discussed, together with its use as building block for the manufacture of advanced wound dressings. Commercially-available collagen dressings and respective clinical performance will be presented, followed by an overview on the latest research advances in the context of multifunctional collagen systems for advanced wound care., Comment: 37 pages, 6 figures, 1 table (to appear in "Advanced Textiles for Wound Care, 2nd ed")

Manuka honey (MH) is used as an antibacterial agent in bioactive wound dressings via direct impregnation onto a suitable substrate. MH provides unique antibacterial activity when compared with conventional honeys, owing partly to one of its constituents, methylglyoxal (MGO). Aiming to investigate an antibiotic-free antimicrobial strategy, we studied the antibacterial activity of both MH and MGO (at equivalent MGO concentrations) when applied as a physical coating to a nonwoven fabric wound dressing. When physically coated on to a cellulosic hydroentangled nonwoven fabric, it was found that concentrations of 0.0054 mg cm-2 of MGO in the form of MH and MGO was sufficient to achieve 100 CFU% bacteria reduction against gram-positive Staphylococcus aureus and gram-negative Klebsiella pneumoniae, based on BS EN ISO 20743:2007. A 3- to 20- fold increase in MGO concentration (0.0170 - 0.1 mg cm-2) was required to facilitate a good antibacterial effect (based on BS EN ISO 20645:2004) in terms of zone of inhibition and lack of growth under the sample. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) was also assessed for MGO in liquid form against three prevalent wound and healthcare-associated pathogens, i.e. Staphylococcus aureus, gram-negative Pseudomonas aeruginosa and gram-positive Enterococcus faecalis. Other than the case of MGO-containing fabrics, solutions with much higher MGO concentrations (128 mg L-1 - 1024 mg L-1) were required to provide either a bacteriostatic or bactericidal effect. The results presented in this study therefore demonstrate the relevance of MGO-based coating as an environment-friendly strategy for the design of functional dressings with antibiotic-free antimicrobial chemistries., Comment: 19 pages, 4 figures, 7 tables. Accepted in Materials

Currently two factors hinder the use of collagen as building block of regenerative devices: the potential antigenicity, and limited mechanical strength in aqueous environment. Polymeric collagen is naturally found in the cross-linked state and is mechanically tougher than the monomeric, cross-link-free (acid-soluble) collagen ex vivo. The antigenicity of collagen, on the other hand, is mainly ascribed to inter-species variations in amino acid sequences, which are primarily located in the non-helical terminal telopeptides. Although these can be removed through enzymatic treatment to produce atelocollagen, the effect of telopeptide removal on triple helix organization, amino acidic composition and thermal properties is often disregarded. Here, we compare the structural, chemical and physical properties of polymeric and monomeric type I collagen with and without telopeptides, in an effort to elucidate the influence that either covalent crosslinks or telopeptides possess. Circular dichroism (CD) was used to examine the triple helical conformation and quantify the denaturation temperature (Td) of both monomeric collagen (36.5 {\deg}C) and monomeric atelocollagen (35.5 {\deg}C). CD measurements were combined with differential scanning calorimetry (DSC) in order to gain insight into the triple helix-to-coil thermal transition and shrinkage temperature (Ts) of polymeric atelo collagen (44.8 {\deg}C), polymeric collagen (62.7 {\deg}C), monomeric atelo collagen (51.4 {\deg}C) and monomeric collagen (66.5 {\deg}C). Structural and thermal analyses were combined with high pressure liquid chromatography (HPLC) to determine the content of specific collagen amino acidic residues used as markers for the presence of telopeptides and mature crosslinks., Comment: 15 pages, 3 figures, 2 tables, Materials Science and Engineering C 2017

Thiol-ene photo-click hydrogels were prepared via step-growth polymerisation using thiol-functionalised type-I collagen and 8-arm poly(ethylene glycol) norbornene terminated (PEG-NB), as a potential injectable regenerative device. Type-I collagen was thiol-functionalised by a ring opening reaction with 2-iminothiolane (2IT), whereby up to 80 Abs% functionalisation and 90 RPN% triple helical preservation were recorded via 2,4,6-Trinitrobenzenesulfonic acid (TNBS) colorimetric assay and circular dichroism (CD). Type, i.e. 2-Hydroxy-1-[4-(2-hydroxyethoxy)phenyl]-2-methyl-1-propanone (I2959) or lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP), and concentration of photoinitiator were varied to ensure minimal photoinitiator-induced cytotoxicity and to enable thiol-ene network formation of collagen-PEG mixtures. The viability of G292 cells following 24 h culture in photoinitiator-supplemented media was largely affected by the photoinitiator concentration, with I2959-supplemented media observed to induce higher toxic response compared to LAP-supplemented media. In line with the in vitro study, selected photoinitiator concentrations were used to prepare thiol-ene photo-click hydrogels. Gelation kinetics proved to be largely affected by the specific photoinitiator, with LAP-containing thiol-ene mixtures leading to significantly reduced complete gelation time with respect to I2959-containing mixtures. Other than the specific photoinitiator, the photoinitiator concentration was key to adjust hydrogel storage modulus (G'), whereby 15-fold G' increase was observed in samples prepared with 0.5% (w/v) compared to 0.1% (w/v) LAP. The photoinitiator-gelation-cytotoxicity relationships established in this study will be instrumental to the design of orthogonal collagen-based niches for regenerative medicine., Comment: 29 pages, 6 figures, 2 schemes, 3 tables. Accepted in "Polymers"

Chitosan (CT) is an antibacterial polysaccharide that has been investigated for drug carriers, haemostats and wound dressings. For these applications, customised CT devices can often be obtained with specific experimental conditions, which can irreversibly alter native biopolymer properties and functions and lead to unreliable material behaviour. In order to investigate the structure-function relationships in CT covalent networks, monosodium 5-sulfoisophthalate (PhS) was selected as heparin-mimicking, growth factor-binding crosslinking segment, whilst 1,4-phenylenediacetic acid (4Ph) and poly(ethylene glycol) bis(carboxymethyl) ether (PEG) were employed as sulfonic acid-free diacids of low and high crosslinker length respectively. Hydrogels based on short crosslinkers (PhS and 4Ph) displayed increased crosslink density, decreased swelling ratio as well as minimal hydrolytic and lysozymic degradation, whilst addition of lysozymes to PEG based networks resulted in 70 wt.-% mass loss. PhS-crosslinked CT hydrogels displayed the highest loss (40 +/- 6 CFU%) of antibacterial activity upon incubation with Porphyromonas gingivalis, whilst respective extracts were tolerated by L929 mouse fibroblasts., Comment: 3 Figures, 1 Table, 1 Supporting Scheme, Materials Letters 2016

Developing successful scaffolds requires clinicians to adopt a multidisciplinary approach in order to understand and stimulate the natural bone regeneration process. A variety of natural and synthetic biomaterials, including naturally extracted, chemically functionalised collagen and synthetic Poly(epsilon-caprolactone) (PCL), can be manufactured into fibres, enabling the formation of nonwoven scaffolds. Many different nonwoven architectures and structural features can then be introduced, depending on the manufacturing parameters. This chapter introduces methods for producing scaffolds with appropriate pore sizes by means of electrospinning, and it outlines the opportunities that exist for other nonwoven manufacturing technologies in the development of biomimetic products., Comment: 4 figures, 1 table, Biomedical Textiles for Orthopaedic and Surgical Applications (book) 2016

Self-assembling peptides (SAPs) have shown to offer great promise in therapeutics and have the ability to undergo self-assembly and form ordered nanostructures. However SAP gels are often associated with inherent weak and transient mechanical properties and incorporation of them into polymeric matrices is a route to enhance their mechanical stability. The aim of this work was to incorporate P11-8 peptide (CH3COQQRFOWOFEQQNH2) within poly(epsilon-caprolactone) (PCL) fibrous webs via one-step electrospinning, aiming to establish the underlying relationships between spinning process, molecular peptide conformation, and material internal architecture. Electrospinning of PCL solutions (6% w/w) in hexafluoro-2-propanol (HFIP) containing up to 40 mg/ml P11-8 resulted in the formation of fibres in both nano- (10-100 nm) and submicron range (100-700 nm), in contrast to PCL only webs, which displayed a predominantly submicron fibre distribution. FTIR and CD spectroscopy on both PCL/peptide solutions and resulting electrospun webs revealed monomeric and beta-sheet secondary conformation, respectively, suggesting the occurrence of peptide self-assembly during electrospinning due to solvent evaporation. The peptide concentration (0 -> 40 mg/ml) was found to primarily affect the internal structure of the fabric at the nano-scale, whilst water as well as cell culture medium contact angles were dramatically decreased. Nearly no cytotoxic response (> 90% cell viability) was observed when L929 mouse fibroblasts were cultured in contact with electrospun peptide loaded samples. This novel nanofibrous architecture may be the basis for an interesting material platform for e.g. hard tissue repair, in light of the presence of the self assembled P11-8 in the PCL fibrous structure., Comment: Journal of Materials Chemistry B 2016

Biomimetic hydrogels based on natural polymers are a promising class of biomaterial, mimicking the natural extra-cellular matrix of biological tissues and providing cues for cell attachment, proliferation and differentiation. With a view to providing an upstream method to guide subsequent experimental design, the aim of this study was to introduce a mathematical model that described the rheological properties of a hydrogel system based on covalently crosslinked collagen triple helices. In light of their organization, such gels exhibit limited collagen bundling that cannot be described by existing fibril network models. The model presented here treats collagen triple helices as discrete semi-flexible polymers, permits full access to metrics for network microstructure, and should provide a comprehensive understanding of the parameter space associated with the development of such multi-functional materials. Triple helical hydrogel networks were experimentally obtained via reaction of type I collagen with both aromatic and aliphatic diacids. The complex modulus G* was found from rheological testing in linear shear and quantitatively compared to model predictions. In silico data from the computational model successfully described the experimental trends in hydrogel storage modulus with either (i) the concentration of collagen triple helices during crosslinking reaction or (ii) the type of crosslinking segment introduced in resulting hydrogel networks. This approach may pave the way to a step change in the rational design of biomimetic triple helical collagen systems with controlled multi-functionality., Comment: 9 figures, 1 scheme, 1 table, ACS Biomaterials Science and Engineering 2016

The design of exudate-managing wound dressings is an established route to accelerated healing, although such design remains a challenge from material and manufacturing standpoints. Aiming towards the clinical translation of knowledge gained in vitro with highly swollen rat tail collagen hydrogels, this study investigated the healing capability in a diabetic mouse wound model of telopeptide-free, protease-inhibiting collagen networks. 4 vinylbenzylation and UV irradiation of type I atelocollagen (AC) led to hydrogel networks with chemical and macroscopic properties comparable to previous collagen analogues, attributable to similar lysine content and dichroic properties. After 4 days in vitro, hydrogels induced nearly 50 RFU% reduction in matrix metalloproteinase (MMP)-9 activity, whilst showing less than 20 wt.-% weight loss. After 20 days in vivo, dry networks promoted 99% closure of 10x10 mm full thickness wounds and accelerated neodermal tissue formation compared to Mepilex. This collagen system can be equipped with multiple, customisable properties and functions key to personalised chronic wound care., Comment: 30 pages, 1 scheme, 6 Figures, 2 Supporting Figures

Self-assembling peptides (SAPs) have the ability to spontaneously assemble into ordered nanostructures enabling the manufacture of "designer" nanomaterials. The reversible molecular association of SAPs has been shown to offer great promise in therapeutics via for example, the design of biomimetic assemblies for hard tissue regeneration. This could be further exploited for novel nano/micro diagnostic tools. However, self-assembled peptide gels are often associated with inherent weak and transient mechanical properties. Their incorporation into polymeric matrices has been considered as a potential strategy to enhance their mechanical stability. This study focuses on the incorporation of an 11-residue peptide, P11-8 (peptide sequence: CH3CO-Gln-Gln-Arg-Phe-Orn-Trp-Orn-Phe-Glu-Gln-Gln-NH2) within a fibrous scaffold of poly ({\epsilon}-caprolactone) (PCL). In this study an electrospinning technique was used to fabricate a biomimetic porous scaffold out of a solution of P11-8 and PCL which resulted in a biphasic structure composed of submicron fibers (diameter of 100-700 nm) and nanofibers (diameter of 10-100 nm). The internal morphology of the fabric and its micro-structure can be easily controlled by changing the peptide concentration. The secondary conformation of P11-8 was investigated in the as-spun fibers by ATR-FTIR spectroscopy and it is shown that peptide self-assembly into \{b}eta-sheet tapes has taken place during fiber formation and the deposition of the fibrous web., Comment: 6 pages, 3 figures, accepted on MRS Advances

Covalent functionalisation of collagen has been shown to be a promising strategy to adjust the mechanical properties of highly swollen collagen hydrogels. At the same time, secondary interactions between for example, amino acidic terminations or introduced functional groups also play an important role and are often challenging to predict and control. To explore this challenge, 4-vinylbenzyl chloride (4VBC) and methacrylic anhydride (MA) were reacted with type I collagen, and the swelling and rheological properties of resulting photo activated hydrogel systems investigated. 4VBC-based hydrogels showed significantly increased swelling ratio, in light of the lower degree of collagen functionalisation, with respect to methacrylated collagen networks, whilst rheological storage moduli were found to be comparable between the two systems. To explore the role of benzyl groups in the mechanical properties of the 4VBC-based collagen system, model chemical force microscopy (CFM) was carried out in aqueous environment with an aromatised probe against an aromatised gold coated glass slide. A marked increase in adhesion force (F: 0.11 +/- 0.01 nN) was measured between aromatised samples, compared to the adhesion force observed between the non-modified probe and a glass substrate (F: 2.64 +/- 1.82 nN). These results suggest the formation of additional and reversible {\pi}-{\pi} stacking interactions in aromatic 4VBC-based networks and explain the remarkable rheological properties of this system in comparison to MA based hydrogels., Comment: 6 pages, 4 figures, accepted in MRS Advances on 3 December 2015

One of the limitations of electrospun collagen as bone-like fibrous structure is the potential collagen triple helix denaturation in the fibre state and the corresponding inadequate wet stability even after crosslinking. Here, we have demonstrated the feasibility of accomplishing wet-stable fibres by wet spinning and diacid-based crosslinking of collagen triple helices, whereby fibre ability to act as bone-mimicking mineralisation system has also been explored. Circular dichroism (CD) demonstrated nearly complete triple helix retention in resulting wet-spun fibres, and the corresponding chemically crosslinked fibres successfully preserved their fibrous morphology following 1-week incubation in phosphate buffer solution (PBS). The presented novel diacid-based crosslinking route imparted superior tensile modulus and strength to the resulting fibres indicating that covalent functionalization of distant collagen molecules is unlikely to be accomplished by current state-of-the-art carbodiimide-based crosslinking. To mimic the constituents of natural bone extra cellular matrix (ECM), the crosslinked fibres were coated with carbonated hydroxyapatite (CHA) through biomimetic precipitation, resulting in an attractive biomaterial for guided bone regeneration (GBR), e.g. in bony defects of the maxillofacial region., Comment: 35 pages, 14 figures, 1 table, 1 scheme (manuscript accepted in "Polymer")

Poly-dl-lactic acid (PDLLA) was blended with type I collagen to attempt to overcome the instantaneous gelation of electrospun collagen scaffolds in biological environments. Scaffolds based on blends of type I collagen and PDLLA were investigated for material stability in cell culture conditions (37 {\deg}C; 5% CO2) in which post-electrospinning glutaraldehyde crosslinking was also applied. The resulting wet-stable webs were cultured with bone marrow stromal cells (HBMSC) for five weeks. Scanning electron microscopy (SEM), confocal laser scanning microscopy (CLSM), Fourier transform infra-red spectroscopy (FTIR) and biochemical assays were used to characterise the scaffolds and the consequent cell-scaffold constructs. To investigate any electrospinning-induced denaturation of collagen, identical PDLLA/collagen and PDLLA/gelatine blends were electrospun and their potential to promote osteogenic differentiation investigated. PDLLA/collagen blends with w/w ratios of 40/60, 60/40 and 80/20 resulted in satisfactory wet stabilities in a humid environment, although chemical crosslinking was essential to ensure long term material cell culture. Scaffolds of PDLLA/collagen at a 60:40 weight ratio provided the greatest stability over a five-week culture period. The PDLLA/collagen scaffolds promoted greater cell proliferation and osteogenic differentiation compared to HMBSCs seeded on the corresponding PDLLA/gelatine scaffolds, suggesting that any electrospinning-induced collagen denaturation did not affect material biofunctionality within 5 weeks in vitro., Comment: 20 pages, 7 figures, 1 table

The formation of naturally-derived materials with wet stable fibrous architectures is paramount in order to mimic the features of tissues at the molecular and microscopic scale. Here, we investigated the formation of wet-spun fibres based on collagen-derived polypeptides with comparable chemical composition and varied molecular weight. Gelatin and hydrolysed fish collagen (HFC) were selected as widely-available linear amino-acidic chains of high and low molecular weight, respectively, and functionalised in the wet-spun fibre state in order to preserve the material geometry in physiological conditions. Wet-spun fibre diameter and morphology were dramatically affected depending on the polypeptide molecular weight, wet-spinning solvent (i.e. 2,2,2-Trifluoroethanol and dimethyl sulfoxide) and coagulating medium (i.e. acetone and ethanol), resulting in either bulky or porous internal geometry. Dry-state tensile moduli were significantly enhanced in gelatin and HFC samples following covalent crosslinking with activated 1,3 phenylenediacetic acid (Ph) (E: 726 +/- 43 - 844 +/- 85 MPa), compared to samples crosslinked via intramolecular carbodiimide-mediated condensation reaction (E: 588 +/- 38 MPa). Resulting fibres displayed a dry diameter in the range of 238 +/- 18 - 355 +/- 28 micron and proved to be mechanically-stable (E: 230 kPa) following equilibration with PBS, whilst a nearly-complete degradation was observed after 5-day incubation in physiological conditions., Comment: 26 pages, 7 figures, 3 tables- accepted in 'International Journal of Biological Macromolecules'

As problems of antibiotic resistance increase, a continuing need for effective bioactive wound dressings is anticipated for the treatment of infected chronic wounds. Naturally derived antibacterial agents, such as Manuka honey, consist of a mixture of compounds, more than one of which can influence antimicrobial potency. The non-peroxide bacteriostatic properties of Manuka honey have been previously linked to the presence of methylglyoxal (MGO). The incorporation of MGO as a functional antibacterial additive during fibre production was explored as a potential route for manufacturing wound dressing components. Synthetic MGO and polyvinyl alcohol (PVA) were fabricated into webs of sub-micron fibres by means of electrostatic spinning of an aqueous spinning solution. Composite fabrics were also produced by direct deposition of the PVA-MGO fibres onto a preformed spunbonded nonwoven substrate. Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) and Proton Nuclear Magnetic Resonance (1H-NMR) spectroscopies confirmed the presence of MGO within the resulting fibre structure. The antibacterial activity of the fibres was studied using strains of Staphylococcus aureus and Escherichia coli. Strong antibacterial activity, as well as diffusion of MGO from the fibres was observed at a concentration of 1.55mg/cm-1., Comment: 13 pages, 5 figurses, 2 tables in Journal of Biomaterials Applications 2015

Biological hydrogels have been increasingly sought after as e.g. wound dressings or scaffolds for regenerative medicine, due to their inherent biofunctionality in biological environments. Especially in moist wound healing, the ideal material should absorb large amounts of wound exudate whilst remaining mechanically competent in-situ. Despite their large hydration, however, current biological hydrogels still leave much to be desired in terms of mechanical properties in physiological conditions. To address this challenge, a multi-scale approach is presented for the synthetic design of cyto-compatible collagen hydrogels with tunable mechanical properties (from nano- up to the macro-scale), uniquely high swelling ratios and retained (>70%) triple-helical features. Type I collagen was covalently functionalized with three different monomers, i.e. 4 vinylbenzyl chloride, glycidyl methacrylate and methacrylic anhydride, respectively. Backbone rigidity, hydrogen-bonding capability and degree of functionalization (F: 16&plusmn12 &ndash 91&plusmn7 mol.-%) of introduced moieties governed the structure-property relationships in resulting collagen networks, so that the swelling ratio (SR: 707&plusmn51 &ndash 1996&plusmn182 wt.-%), bulk compressive modulus (Ec: 30&plusmn7 &ndash 168&plusmn40 kPa) and Atomic Force Microscopy elastic modulus (EAFM: 16&plusmn2 &ndash 387&plusmn66 kPa) were readily adjusted. In light of their remarkably high swelling and mechanical properties, these tunable collagen hydrogels may be further exploited for the design of advanced dressings for chronic wound care., Comment: Accepted in "Journal of the Royal Society Interface"

Advanced bioactive systems with defined macroscopic properties and spatio-temporal sequestration of extracellular biomacromolecules are highly desirable for next generation therapeutics. Here, chitosan hydrogels were prepared with neutral or negatively-charged crosslinkers in order to promote selective electrostatic complexation with charged drugs. Chitosan (CT) was functionalised with varied dicarboxylic acids, such as tartaric acid (TA), poly(ethylene glycol) bis(carboxymethyl) ether (PEG), 1.4-Phenylenediacetic acid (4Ph) and 5-Sulfoisophthalic acid monosodium salt (PhS), whereby PhS was hypothesised to act as a simple mimetic of heparin. ATR FT-IR showed the presence of C=O amide I, N-H amide II and C=O ester bands, providing evidence of covalent network formation. The crosslinker content was reversely quantified by 1H-NMR on partially-degraded network oligomers, so that 18 mol% PhS was exemplarily determined. Swellability, compressability, material morphology, and drug-loading capability were successfully adjusted based on the selected network architecture. Here, hydrogel incubation with model drugs of varied electrostatic charge, i.e. allura red (AR, --), methyl orange (MO, -) or methylene blue (MB, +), resulted in direct hydrogel-dye electrostatic complexation. Importantly, the cationic compound, MB, showed different incorporation behaviours, depending on the electrostatic character of the selected crosslinker. In light of this tuneable drug-loading capability, these CT hydrogels would be highly attractive as drug reservoirs towards e.g. the fabrication of tissue models in vitro., Comment: Manuscript accepted in Acta Biomaterialia

Chemical crosslinking of collagen is a general strategy to reproduce macroscale tissue properties in physiological environment. However, simultaneous control of protein conformation, material properties and biofunctionality is highly challenging with current synthetic strategies. Consequently, the potentially-diverse clinical applications of collagen-based biomaterials cannot be fully realised. In order to establish defined biomacromolecular systems for mineralised tissue applications, type I collagen was functionalised with 1,3-Phenylenediacetic acid (Ph) and investigated at the molecular, macroscopic and functional levels. Preserved triple helix conformation was observed in obtained covalent networks via ATR-FTIR and WAXS, while network crosslinking degree could be adjusted based on specific reaction conditions. Decreased swelling ratio and increased thermo-mechanical properties were observed compared to state of-the-art carbodiimide (EDC)-crosslinked collagen controls, likely related to the intermolecular covalent incorporation of the aromatic segment. Ph crosslinked hydrogels displayed nearly intact material integrity and only a slight mass decrease following 1-week incubation in either PBS or simulated body fluid (SBF), in contrast to EDC crosslinked collagen. Furthermore, FTIR, SEM and EDS revealed deposition of a calcium-phosphate phase on SBF-retrieved samples, whereby an increased calcium phosphate ratio was observed in hydrogels with higher Ph content. 72-hour material extracts were well tolerated by L929 mouse fibroblasts, whereby cell confluence and metabolic activity (MTS assay) were comparable to those of cells cultured in cell culture medium (positive control). In light of their controlled structure-function properties, these biocompatible collagen hydrogels represent attractive material systems for potential mineralised tissue applications., Comment: Accepted manuscript, Journal of Materials Chemistry B

The design of photo-active collagen systems is presented as a basis for establishing biomimetic materials with varied network architecture and programmable macroscopic properties. Following in-house isolation of type I collagen, reaction with vinyl-bearing compounds of varied backbone rigidity, i.e. 4-vinylbenzyl chloride (4VBC) and glycidyl methacrylate (GMA), was carried out. TNBS colorimetric assay, 1H-NMR and ATR-FTIR confirmed covalent and tunable functionalization of collagen lysines. Depending on the type and extent of functionalization, controlled stability and thermal denaturation of triple helices were observed via circular dichroism (CD), whereby the hydrogen-bonding capability of introduced moieties was shown to play a major role. Full gel formation was observed following photo-activation of functionalized collagen solutions. The presence of a covalent network only slightly affected collagen triple helix conformation (as observed by WAXS and ATR-FTIR), confirming the structural organization of functionalized collagen precursors. Photo-activated hydrogels demonstrated an increased denaturation temperature (DSC) with respect to native collagen, suggesting that the formation of the covalent network successfully stabilized collagen triple helices. Moreover, biocompatibility and mechanical competence of obtained hydrogels were successfully demonstrated under physiologically-relevant conditions. These results demonstrate that this novel synthetic approach enabled the formation of biocompatible collagen systems with defined network architecture and programmable macroscopic properties, which can only partially be obtained with current synthetic methods., Comment: Journal of Materials Chemistry B (2013)

In order to establish defined biomimetic systems, type I collagen was functionalised with 1,3-Phenylenediacetic acid (Ph) as aromatic, bifunctional segment. Following investigation on molecular organization and macroscopic properties, material functionalities, i.e. degradability and bioactivity, were addressed, aiming at elucidating the potential of this collagen system as mineralization template. Functionalised collagen hydrogels demonstrated a preserved triple helix conformation. Decreased swelling ratio and increased thermo-mechanical properties were observed in comparison to state-of-the-art carbodiimide (EDC)-crosslinked collagen controls. Ph-crosslinked samples displayed no optical damage and only a slight mass decrease (~ 4 wt.-%) following 1-week incubation in simulated body fluid (SBF), while nearly 50 wt.-% degradation was observed in EDC-crosslinked collagen. SEM/EDS revealed amorphous mineral deposition, whereby increased calcium phosphate ratio was suggested in hydrogels with increased Ph content. This investigation provides valuable insights for the synthesis of triple helical collagen materials with enhanced macroscopic properties and controlled degradation. In light of these features, this system will be applied for the design of tissue-like scaffolds for mineralized tissue formation., Comment: 2012 MRS Fall Meeting Proceedings

This thesis presents the development of entropy-elastic gelatin based networks in the form of films or scaffolds. The materials have good prospects for biomedical applications, especially in the context of bone regeneration. Entropy-elastic gelatin based hydrogel films with varying crosslinking densities were prepared with tailored mechanical properties. Gelatin was covalently crosslinked in water above its sol gel transition, which suppressed the gelatin chain helicity. Amorphous films were prepared with tailorable degrees of swelling and wet state Young's modulus. The knowledge gained with this bulk material was transferred to the integrated process of foaming and crosslinking to obtain porous gelatin-based scaffolds. A gelatin solution was foamed in the presence of saponin and the resulting foam was fixed by chemical crosslinking with a diisocyanate. The scaffolds were analyzed in the dry state by micro computed tomography (\mu CT, porosity: 65\pm 11-73\pm 14 vol.-%), and scanning electron microscopy (SEM, pore size: 117\pm 28-166 \pm 32 \mu m). After equilibration with water, the scaffolds were form-stable and displayed shape recovery after removal of mechanical loads. The composition dependent compression moduli (Ec: 10 50 kPa) were comparable to the bulk micromechanical Young's moduli, which were measured by atomic force microscopy (AFM). The hydrolytic degradation profile could be adjusted, and a controlled decrease of mechanical properties was observed. The scaffold cytotoxicity and immunologic responses were analyzed in vitro. Indirect eluate tests were carried out with L929 cells so that fully cytocompatible scaffolds were obtained. Furthermore, the material immune response was investigated in vitro. Minimal material endotoxin contamination was successfully achieved (<0.5 EU/mL) by using low-endotoxin gelatin and performing all synthetic steps in cleanroom., Comment: PhD thesis, University of Potsdam, Germany, December 2010