Search

Grafting polyethylene glycol (PEG) onto a polymer's surface is widely used to improve biocompatibility by reducing protein and cell adhesion. Although PEG is considered to be bioinert, its incorporation onto biomaterials has shown to improve cell viability depending on the amount and molecular weight (MW) used. This phenomenon was studied here by grafting PEG of three MW onto polyurethane (PU) substrata at three molar concentrations to assess their effect on PU surface properties and on the viability of osteoblasts and fibroblasts. PEG formed a covering on the substrata which increased the hydrophilicity and surface energy of PUs. Among the results, it was observed that osteoblast viability increased for all MW and grafting densities of PEG employed compared with unmodified PU. However, fibroblast viability only increased at certain combinations of MW and grafting densities of PEG, suggesting an optimal level of these parameters. PEG grafting also promoted a more spread cell morphology than that exhibited by unmodified PU; nevertheless, cells became apoptotic-like as PEG MW and grafting density were increased. These effects on cells could be due to PEG affecting culture medium pH, which became more alkaline at higher MW and concentrations of PEG. Results support the hypothesis that surface energy of PU substrates can be tuned by controlling the MW and grafting density of PEG, but these parameters should be optimized to promote cell viability without inducing apoptotic-like behavior.

The surface of Tecoflex SG-80A Polyurethane (PU) films was modified by grafting polyethylene glycol (PEG) chains at three different molar amounts (0.05, 0.10, and 0.15 mmol). The resulting substrata were characterized by FTIR-ATR, TGA, AFM, SEM and contact angle to assess the surface modifications occurred during the grafting reactions. Osteoblasts and fibroblasts were cultured with PU extracts for 24 h, and their cell viability and morphology were evaluated by CellTiterBlue assay, Crystal Violet staining and Live/Dead assay. FTIR and TGA results indicated that PEG chains were successfully grafted onto PU surfaces, specifically in the hard segment of PU forming allophanate groups as the PEG grafting density increased. SEM and AFM images suggest that PU substrata were partially covered by PEG, increasing the dispersive and basic components of the PU surface energy. It was found that extracts from PEG-grafted polyurethanes increased the osteoblast viability, although fibroblasts viability remained constant regardless PEG grafting density; in spite of this both cells presented a more spread morphology at the lower PEG grafting density. Our results showed that surface energy of PU substrata can be tuned by PEG grafting density; also, the PEG leached tends to increase the pH of culture medium which leads to a higher viability of osteoblasts; nevertheless, PEG grafting density should be optimized to promote a healthy cell morphology as alterations in its morphology were detected at higher concentrations. Graphical abstract., (© 2022. The Author(s).)

Bis-GMA/TTEGDMA-based resin composites were prepared with two different types of nanoclays: an organically modified laminar clay (Cloisite ® 30B, montmorillonite, MMT) and a microfibrous clay (palygorskite, PLG). Their physicochemical and mechanical properties were then determined. Both MMT and PLG nanoclays were added into monomer mixture (1:1 ratio) at different loading levels (0, 2, 4, 6, 8 and 10 wt.%), and the resulting composites were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and mechanical testing (bending and compressive properties). Thermal properties, depth of cure and water absorption were not greatly affected by the type of nanoclay, while the mechanical properties of dental resin composites depended on both the variety and concentration of nanoclay. In this regard, composites containing MMT displayed higher mechanical strength (both flexural and compression) than those resins prepared with PLG due to a poor nanoclay dispersion as revealed by SEM. Solubility of the composites was dependent not only on nanoclay-type but also the mineral concentration. Dental composites fulfilled the minimum depth cure and solubility criteria set by the ISO 4049 standard. In contrast, the minimum bending strength (50 MPa) established by the international standard was only satisfied by the dental resins containing MMT. Based on these results, composites containing either MMT or PLG (at low filler contents) are potentially suitable for use in dental restorative resins, although those prepared with MMT displayed better results., Competing Interests: The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.