Search

A series of ethylene-octene copolymer (EOC) composites have been prepared by melt-mixing with different weight ratios of expandable graphite filler (0-50% by weight). Electrical conductivity [both alternating current (AC) and direct current (DC)] and thermal conductivity studies were carried out. Effect of filler loading and frequency on electrical conductivity was studied. DC conductivity has increased from 1.51 x [10.sup.-13] S [cm.sup.-1] to 1.17 X [10.sup.-1] 1 S [cm.sup.-1] . Percolation threshold by DC and also AC methods was observed at about 16 vol% of the filler. Real part of permittivity was found to be decreasing with increase in frequency while conductivity was increasing. Thermal conductivity was also found to be increasing gradually from 0.196 to 0.676 [Wm.sup.1] [K.sup.1] which is about 245% increase. Graphite not only increases the electrical and thermal conductivities but at and above 40 wt%, also acts as a halogen-free, environmental friendly flame retardant. Shore-A hardness of EOC/graphite composites shows that even with high graphite loading, the hardness is increased from about 50-68 only so that the rubbery nature of the composite is not affected very much. POLYM. ENG. SCI., 52:1241-1249, 2012. © 2012 Society of Plastics Engineers, INTRODUCTION Polymer composites with conducting fillers serve as electrical or thermal conductors and have wide range of applications in the electric and electronic fields. These composites have an advantage of [...]

The gadolinium (Gd3+) substituted zinc ferrite nanoparticles (ZnFe2−xGdxO4) for Gd3+ (x = 0.00, 0.05, 0.10, 0.20) have been synthesized by honey mediated sol-gel auto-combustion method. The X-ray diffraction study revealed the formation of spinel ferrite crystal structure. The Raman spectroscopy and Fourier transform infrared spectroscopy study well support the XRD results analysis. The field emission scanning electron microscopy micrograph revealed spherical morphology and grain size around 10-30 nm for ZnFe2−xGdxO4 (x = 0.10) nanoparticles. The presence of Zn2+ and Fe3+ oxidation state in synthesized nanoparticles was confirmed by X-ray photoelectron spectroscopy. Magnetic properties of the Gd3+ substituted zinc ferrite nanoparticles were investigated by vibrating sample magnetometer at room temperature. The conversion of magnetic hysteresis curves from ferromagnetic to a paramagnetic with the substitution of Gd3+ in zinc ferrite nanoparticles was observed. Frequency dependent dielectric constant and ac conductivity measurements revealed that Gd3+ substitution improved the value of dielectric constant and ac conductivity of the Gd3+ substituted zinc ferrite nanoparticles. Further, the existence of two semicircles in Cole-Cole plot demonstrated the role of both grains and grain boundaries to conduction process in synthesized Gd3+ ion substituted zinc ferrite nanoparticles. Furthermore, the grain relaxation time (τg), grain boundary relaxation time (τgb), grain resistance (Rg), grain capacitance (Cg), grain boundary resistance (Rgb) and grain boundary capacitance (Cgb) for synthesized ZnFe2−xGdxO4 (x = 0.00, 0.05, 0.10, 0.20) nanoparticles have been calculated using modulus spectroscopy analysis. [ABSTRACT FROM AUTHOR]

Microscopical, differential scanning colorimetry (DSC), and X-ray structural investigations of solution crystallized carbon nanotube (CNT) composites with linear polyethylene (LPE), isotactic polypropylene (iPP), polybutene-1 (PB-1), and nylon 6 (PA6) disclosed varying degrees of surface interaction and nucleation effect of CNT in these polymers and formation of oriented shish-kebab overgrowths on the CNT ropes in LPE and PA6. The character of the attraction and orientation forces at the CNT-polymer interface is discussed. [ABSTRACT FROM AUTHOR]

The development of flexible, lightweight, and thin high-performance electromagnetic interference shielding materials is urgently needed for the protection of humans, the environment, and electronic devices against electromagnetic radiation. To achieve this, the spinel ferrite nanoparticles CoFe 2 O 4 (CZ1), Co 0.67 Zn 0.33 Fe 2 O 4 (CZ2), and Co 0.33 Zn 0.67 Fe 2 O 4 (CZ3) were prepared by the sonochemical synthesis method. Further, these prepared spinel ferrite nanoparticles and reduced graphene oxide (rGO) were embedded in a thermoplastic polyurethane (TPU) matrix. The maximum electromagnetic interference (EMI) total shielding effectiveness (SE T ) values in the frequency range 8.2-12.4 GHz of these nanocomposites with a thickness of only 0.8 mm were 48.3, 61.8, and 67.8 dB for CZ1-rGO-TPU, CZ2-rGO-TPU, and CZ3-rGO-TPU, respectively. The high-performance electromagnetic interference shielding characteristics of the CZ3-rGO-TPU nanocomposite stem from dipole and interfacial polarization, conduction loss, multiple scattering, eddy current effect, natural resonance, high attenuation constant, and impedance matching. The optimized CZ3-rGO-TPU nanocomposite can be a potential candidate as a lightweight, flexible, thin, and high-performance electromagnetic interference shielding material., Competing Interests: The authors declare no competing financial interest., (© 2021 The Authors. Published by American Chemical Society.)

In this work, nickel ferrite (NiFe 2 O 4 ) nanoparticles were synthesized by dextrin from corn-mediated sol-gel combustion method and were annealed at 600, 800, and 1000 °C. The structural and physical characteristics of prepared nanoparticles were studied in detail. The average crystallite size was 20.6, 34.5, and 68.6 nm for NiFe 2 O 4 nanoparticles annealed at 600 °C (NFD@600), 800 °C (NFD@800), and 1000 °C (NFD@1000), respectively. The electromagnetic interference shielding performance of prepared nanocomposites of NiFe 2 O 4 nanoparticles (NFD@600 or NFD@800 or NFD@1000) in polypropylene (PP) matrix engineered with reduced graphene oxide (rGO) have been investigated; the results indicated that the prepared nanocomposites consisted of smaller-sized nickel ferrite nanoparticles exhibited excellent electromagnetic interference (EMI) shielding characteristics. The total EMI shielding effectiveness (SE T ) for the prepared nanocomposites have been noticed to be 45.56, 36.43, and 35.71 dB for NFD@600-rGO-PP, NFD@800-rGO-PP, and NFD@1000-rGO-PP nanocomposites, respectively, at the thickness of 2 mm in microwave X-band range (8.2-12.4 GHz). The evaluated values of specific EMI shielding effectiveness (SSE) were 38.81, 32.79, and 31.73 dB·cm 3 /g, and the absolute EMI shielding effectiveness (SSE/t) values were 388.1, 327.9, and 317.3 dB·cm 2 /g for NFD@600-rGO-PP, NFD@800-rGO-PP, and NFD@1000-rGO-PP, respectively. The prepared lightweight and flexible sheets can be considered useful nanocomposites against electromagnetic radiation pollution., Competing Interests: The authors declare no competing financial interest., (Copyright © 2019 American Chemical Society.)