Search

The Phase-Resolved-Partial-Discharge pattern (PRPD) is a conventional technique used for the evaluation of partial discharges (PD) phenomena in High-Voltage-Alternating-Current (HVAC) systems. This map is constructed by plotting the peak of each detected pulses as a function of the phase angle of the supply voltage. Therefore it is obvious that this technique cannot be used for the analysis of data from PD mesaurement under different supply voltage condition (DC). The aim of this paper is to evaluate the application of the Time-Frequency map (TF map) for the analysis of a dataset obtained from PD measurement under DC voltage. A density-based clustering algorithm was also used to gain more insight from the collected data. The results show that, with this approach, it's possible to perform a noise rejection and identify PD pulses.

To date, there are several methods for calculating the electric field distribution within a dielectric layer subjected to HVDC voltage. However, experimental techniques for evaluating the accuracy of models for calculating the electric field, such as space charge measurement, are often not precise enough to be used for this purpose. At the same time, the knowledge of Partial Discharge (PD) phenomenon occurring under HVDC stress is also not as developed as that of PD under HVAC voltage. The main goal of this research is to study the effectiveness of dielectric conductivity models to forecast the inception condition for PD under load and HVDC voltage stress. This study has been carried out by means of comparison between computer simulation and experimental results. The simulations have been carried out by means of a dielectric conductivity model implemented in the FEM software Comsol Multiphysics. The experimental setup consist of a model cable insulated with XLPE with an artificial defect created at the outer surface of the dielectric layer. Although the definition of the electric field inside a cavity is affected by several parameters which are also mutually dependent, the analysis performed demonstrates the predictability of the PD activity within certain voltage and temperature ranges.

In this paper, a new low-cost device is proposed for fault location in power distribution system. The device is part of a system that should include several units installed in couples at the two ends of medium voltage (MV) cable lines. Their low cost justifies a widespread installation of these devices, moreover other functionalities could be considered so as to enrich the potential of the system for MV cables monitoring and asset management. The system exploits a two-end traveling wave technique, low complexity, and low-cost solutions both for the analog front end as well as for the communication infrastructure. A LoRa network is indeed considered as wireless modulation technique perfectly suited when communication links with three characteristics are needed: low power, low bit rate, and long range. This paper shows the device that has been set up in Prysmian Electronics with some experimental phases showing the effectiveness of the proposed solution and the further developments expected.

In this paper, an original formulation of the control problem for optimal PV array reconfiguration, following a Total Cross Tied layout, is proposed. The formulation follows the well-known subset sum problem, which is a special case of the knapsack problem. The reconfiguration is a measure devoted to mitigate the mismatch effect and maximize the output power of small photovoltaic plants under non-homogeneous working conditions. Therefore, reconfiguration means changing the connections of the solar panels adaptively by a dynamic switching matrix. The control system implements an easy dynamic programming algorithm to change the switches layout. The use of the Munkres assignment method in a post-processing module makes the algorithm able to obtain the optimum configuration for which it is possible to balance and minimize the aging of the switches within the switching matrix.

In this paper it is presented a testing prototype of a reconfiguration system for photovoltaic (PV) plants. The system enables to increase the total energy output by reducing the electrical mismatch between the PV array modules. The architecture of the implemented switching matrix, performing the dynamic electrical interconnections of the PV panels, enables to reconfigure nine solar modules in a series-parallel (SP) configuration. The contribution is organized as follows. A brief state of the art is first presented, followed by a comparison between the SP and Total-Cross-Tied (TCT) connections. The prototype then is thoroughly described as well as the main design choices. Finally some tests and an extrapolation of its performance over a real size PV field are reported.

This work presents a preliminary study on the implementation of a new system for power output maximization of photovoltaic generators under non-homogeneous conditions. The study evaluates the performance of an efficient switching matrix and the relevant automatic reconfiguration control algorithms. The switching matrix is installed between the PV generator and the inverter, allowing a large number of possible module configurations. PV generator, switching matrix and the intelligent controller have been simulated in Simulink. The proposed reconfiguration system improved the energy extracted by the PV generator under non-uniform solar irradiation conditions. Short calculation times of the proposed control algorithms allow its use in real time applications even where a higher number of PV modules is required.

The main objective of this paper is the assessment of the exact phase angle displacement of each Partial Discharge, PD, pulse with respect to the voltage reference waveform. Such problem also referred to as ‘synchronization’ is relevant when the cable is not accessible and the PD measure is carried out in wireless mode. It is well known, that the angle phase shift, due to the propagation phenomenon on the transmission line, can be calculated knowing the line type and length and typical operating conditions of the transmission line. The setup comprises a customized electronic device, the “Phase check”, a server to collect remote measurements and a Look up table to provide corrections to the measured phase shift values. To evaluate the voltage phase shift introduced by a transmission line, different simulations have been carried out in PSCAD. Then, to prove the correctness of simulated results and verify the “Phase check” precision, experimental measurements have been carries out on three transmission lines in Sicily, Italy. The experimental measurements prove that the proposed setup is effective and quite useful to provide precise assessment of voltage phase shift for PD wireless diagnosis.

In this paper, several aspects of the fundamentals of wireless Partial Discharge (PD) measurements are first discussed. Then, the relevance of the problem of voltage synchronization in PD wireless diagnosis is outlined. When portable instruments are used for PD detection, the main issue is the voltage measurement at the site where the PD detection is carried out. When such analysis is carried out over shielded cables, the AC (50/60 Hz) voltage reference signal is not easily detectable, while one of the basic parameters for PD diagnosis, the displacement of the inception voltage of the PD as compared to the reference voltage, is not available. Even if highperformance sensors are readily available on the market, the authors are investigating the possibility to use remotely measured reference voltage at the closest accessible substation to create a reliable reference, thus reducing the time and associated costs required for performing field wireless measurements.

In order to reduce the mismatch effect caused by non-uniform shadows in PV arrays, reconfigurable interconnections approaches have been recently proposed in the literature. These systems usually require the knowledge of the solar radiation affecting every solar module. The aim of this work is to evaluate the effectiveness of three irradiance estimation approaches in order to define which can be well suited for reconfigurable PV arrays. It is presented a real-time solar irradiance estimation device (IrradEst), implementing the three different estimation methods. The proposed system is based on mathematical models of PV modules enabling to estimate irradiation values by sensing a combination of temperature, voltage and current of a PV module. Experimental results showed generally good agreement between the estimated irradiances and the measurements performed by a standard pyranometer taken as reference. Finally one of the three methods was selected as possible solution for a reconfigurable PV system.