Search

Modularization of heavy industrial plants is a standard mode of operation utilized to reduce costs, site congestion, and schedule. The standard module is 6 m wide, 24 to 36 m long, and up to 7.5 m high (20 ft wide, 80 to 120 ft long and 24 ft high) with weights ranging from 50 to 160 tonnes. On-site traditional rigging arrangements are costly to adjust for dimension and center of gravity and have inherent safety risks in handling the rigging. Additionally, the modules are often over-designed because of uncertainties in the load redistribution due to lifting. The aim of this work is to design a new system, improving upon the limitations of the traditional system. To achieve this goal, a thorough understanding of the traditional system is required. In this paper, finite element analysis was used to analyze the load redistribution due to lifting of three module types with different sizes under various extreme loading scenarios. The results show that load redistribution depends primarily on the triangular assembly of the traditional rigging independent of the module type, size and loading. Secondly, an adjustable and functionally very flexible engineered module lift frame was designed to handle the variety of loading and dimensional conditions and reduce module stresses exerted due to lifting. It is comprised of two main running beams, adjustable interconnecting cross braces, sliders for longitudinal flexibility in connection points, and supporting slings to a common upper point. Finite element analysis was used to confirm the module lift frame loading resistance and to determine its limits under a variety of extreme loading scenarios. There are significant improvements in the module load redistribution forces as compared to traditional rigging. Key words: finite element analysis, rigging, module, construction engineering, structural engineering. La modularisation des usines industrielles lourdes represente un mode de fonctionnement normalise utilise pour reduire les couts, la congestion des sites et l'echeancier. Le module normal mesure 6 m de large, de 24 a 36 m de long, et jusqu'a 7,5 m de haut (20 pi de large, de 80 a 120 pi de long et 24 pi de haut) et son poids varie de 50 a 160 tonnes. Les dispositions des greements traditionnels sur le site sont couteuses a ajuster aux dimensions et au centre de gravite et elles presentent des risques de securite inherents lors de la manutention des greements. De plus, les modules sont souvent surdimensionnes en raison des incertitudes dans la redistribution des charges dues au levage. L'objectif de ce travail est de concevoir un nouveau systeme en ameliorant les restrictions du systeme traditionnel. Pour atteindre cet objectif, il faut tres bien connaitre le systeme traditionnel. Dans cet article, une analyse par elements finis a ete utilisee pour analyser la redistribution des charges en raison du levage de trois types de modules de dimensions differentes selon divers scenarios de chargement extremes. Les resultats montrent que la redistribution des charges depend principalement de l'assemblage triangulaire du greement traditionnel, peu importe le type de module, sa dimension et la charge. Deuxiemement, un cadre de levage des modules, ajustable et tres flexible, a ete concu pour accepter les charges et les dimensions variees et reduire les contraintes sur les modules induites durant le levage. Ce cadre comporte deux poutres longitudinales, des traverses de raccord ajustables, des glisseurs pour permettre une flexibilite longitudinale aux points de raccord, ainsi que des elingues de soutien reliees a un point commun vers le haut. L'analyse par elements finis a permis de confirmer la resistance a la charge du cadre de levage de modules et de determiner ses limites sous divers scenarios de chargement extremes. Il y a eu des ameliorations importantes dans les forces de redistribution des charges de modules lorsqu'on les compare a la redistribution des greements traditionnels. [Traduit par la Redaction] Mots-cles: analyse par elements finis, greement, module, genie construction, genie des structures., 1. Introduction Modular construction is an efficient and cost-effective method to construct large industrial plants. The individual modules are constructed off-site in a controlled environment, transported to the site and [...]

Evaluating the bone-implant interface (BII) properties of osseointegrated transfemoral (TFA) implants is important for early failure detection and prescribing loads during rehabilitation. The objective of this work is to derive and validate a 1D finite element (FE) model of the Osseointegrated Prosthetic Limb (OPL) TFA system that can: (1) model its dynamic behaviour and (2) extract the BII properties. The model was validated by: (1) comparing the 1D FE formulation to the analytical and 3D FE solutions for a simplified cylinder, (2) comparing the vibration modes of the actual TFA geometry using 1D and 3D FE models, and (3) evaluating the BII properties for three extreme conditions (LOW, INTERMEDIATE, and HIGH) generated using 3D FE and experimental (where the implant was embedded, using different adhesives, in synthetic femurs) signals for additional validation. The modes predicted by the 1D FE model converged to the analytical and the 3D FE solutions for the cylinder. The 1D model also matched the 3D FE solution with a maximum frequency difference of 2.02% for the TFA geometry. Finally, the 1D model extracted the BII stiffness and the system's damping properties for the three conditions generated using the 3D FE simulations and the experimental INTERMEDIATE and HIGH signals. The agreement between the 1D FE and the 3D FE solutions for the TFA geometry indicates that the 1D model captures the system's dynamic behaviour. Distinguishing between the different BII conditions demonstrates the 1D model's potential use for the non-invasive clinical evaluation of the TFA BII properties., (© 2024. The Author(s) under exclusive licence to Biomedical Engineering Society.)

The age-based morphometric changes of cranial sutures are not well established, particularly in a quantitative manner. Most prior work utilized planar reslicing approaches to analyze sutures and the quantitative measurements of suture morphometry were limited to a short segment not following the true skull shape. The present study aimed to investigate the age-based morphometric changes of the coronal suture during normal growth of young rats using a novel curved-reslicing approach. Longitudinal in vivo micro-computed tomography (μCT) scans were completed at five time points (7, 9, 11, 16 and 21 weeks of age) during normal growth for 12 Sprague-Dawley rats (six female, six male). Curved-reslicing was performed on μCT slices to generate 11 equidistant cross-sectional images that covered the middle 90 % of skull thickness and the entire length of the coronal suture. The suture linear interdigitation index (LII) and width were measured using a marching algorithm. The average coronal suture LII increased by 15.3 % while the width decreased by 53.5 % at 21 weeks compared to 7 weeks of age, and repeated measures one-way analysis of variance with post-hoc multiple comparisons with Bonferroni adjustment revealed that these differences are statistically significant (p < 0.01). Linear mixed-effect models (LMM) were created for the prediction of rat coronal suture LII and width based on age, relative location through the skull thickness and initial morphometric measurements at the inner surface of the skull. When random effects are considered, the LMM was able to explain up to 97 % and 78 % of variations of suture LII and width, respectively. The presented study has established a novel curved-reslicing method to obtain quantitative 3D information surrounding cranial sutures and demonstrated strong predictive capabilities for suture morphometric changes with age. Future studies considering craniofacial sutures abnormalities will benefit from the presented work through novel methods of studying 3D quantitative morphometry., Competing Interests: Declaration of competing interest The authors declare that they have no known conflicting interests or personal relationships that could have affected the work presented in this article., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

Radiation therapy (RT) is an important adjuvant and primary treatment modality for head and neck cancers. A severe side effect of RT is fibrosis or scarring of muscle tissues of the oral cavity including the tongue. Previous studies have demonstrated that increased radiation doses to the oral cavity structures have led to decrements in function, hypothesized to result from changes in muscle tissue properties that affect the tongue's function. To understand the complex relationship between tongue muscle fibrosis and tongue function, the current study used a virtual biomechanical model of the tongue. Fibrosis parameters including density (high, low), area (large, small) and location (946 node centres) were systematically varied in the model to test its impact on a target tongue tip motion (protrusion). The impact of fibrosis lesion parameters on three directional components of the tip (anterior-inferior, lateral-medial, and superior-inferior) were analyzed using multi linear regression models. Increases in density and area of fibrosis significantly predicted tongue protrusion movements compared to baseline. In the anterior-posterior direction, reductions in the tongue protrusion were observed. In the inferior-superior direction, the tongue height remained above baseline for the majority of cases. In the lateral-medial direction, ipsilateral deviations were observed. The location of fibrosis modulated these three main effects by either amplifying the observed effect or minimizing it. The findings support the hypothesis that changes in muscle tissue properties because of fibrosis impact tongue function. Increases in density and area of fibrosis impact key muscles in the target motion. The range of modulating effects of the lesion location (i.e., either amplifying or minimizing certain impact patterns) highlights the intricacy of tongue anatomy/soft tissue biomechanics and may suggest that lesions in any location will compromise the tongue's movement., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Background and Objective: Tooth extraction is a common clinical procedure with biomechanical factors that can directly influence patient outcomes. Recent development in atraumatic extraction techniques have endeavoured to improve treatment outcomes, but the characterization of extraction biomechanics is sparse. An axisymmetric inverse finite element (FE) approach is presented to represent the biomechanics of vertical atraumatic tooth extraction in an ex-vivo swine model., Methods: Geometry and boundary conditions from the model are determined to match the extraction of swine incisors in a self-aligning ex vivo extraction experiment. Material parameters for the periodontal ligament (PDL) model are determined by solving an inverse FE problem using clusters of data obtained from 10 highly-controlled mechanical experiments. A seven-parameter visco-hyperelastic damage model, based on an Arruda-Boyce framework, is used for curve fitting. Three loading schemes were fit to obtain a common set of material parameters., Results: The inverse FE results demonstrate good predictions for overall force-time curve shape, peak force, and time to peak force. The fit model parameters are sufficiently consistent across all three cases that a coefficient-averaged model was taken that compares well to all three cases. Notably, the initial modulus ,u, converged across trials to an average value of 0.472 MPa with an average viscoelastic constant g of 0.561., Conclusions: The presented model is found to have consistent parameters across loading cases. The capability of this model to represent the fundamental mechanical characteristics of the dental complex during vertical extraction loading is a significant advancement in the modelling of extraction procedures. Future work will focus on verifying the model as a predictive design tool for assessing new loading schemes in addition to investigating its applications to subject-specific problems., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The Advanced System for Implant Stability Testing (ASIST) is a device currently being developed to noninvasively measure implant stability by estimating the mechanical stiffness of the bone-implant interface, which is reported as the ASIST Stability Coefficient (ASC). This study's purpose was to determine whether changes in density, bonding, and drilling technique affect the measured vibration of a dental implant, and whether they can be quantified as a change in the estimated BII stiffness. Stability was also measured using RFA, insertion torque (IT) and the pullout test. Bone-level tapered implants (4.1 mm diameter, 10 mm length) were inserted in polyurethane foam as an artificial bone substitute. Samples were prepared using different bone densities (20, 30, 40 PCF), drilling sequences, and superglue to simulate a bonded implant. Measurements were compared across groups at a significance level of 0.05. The ASC was able to indicate changes in each factor as a change in the interfacial stiffness. IT and pullout force values also showed comparable increases. Furthermore, the relative difference in ISQ values between experimental groups was considerably smaller than the ASC. While future work should be done using biological bone and in-vivo systems, the results of this in-vitro study suggest that modelling of the implant system with a vibration-based approach may provide a noninvasive method of assessing the mechanical stability of the implant., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

An improved understanding of contact mechanics in the ankle joint is paramount for implant design and ankle disorder treatment. However, existing models generally simplify the ankle joint as a revolute joint that cannot predict contact characteristics. The current study aimed to develop a novel musculoskeletal ankle joint model that can predict contact in the ankle joint, together with muscle and joint reaction forces. We modelled the ankle joint as a multi-axial joint and simulated contact mechanics between the tibia, fibula and talus bones in OpenSim. The developed model was validated with results from experimental studies through passive stiffness and contact. Through this, we found a similar ankle moment-rotation relationship and contact pattern between our study and experimental studies. Next, the musculoskeletal ankle joint model was incorporated into a lower body model to simulate gait. The ankle joint contact characteristics, kinematics, and muscle forces were predicted and compared to the literature. Our results revealed a comparable peak contact force and the same muscle activation patterns in four major muscles. Good agreement was also found in ankle dorsi/plantar-flexion and inversion/eversion. Thus, the developed model was able to accurately model the ankle joint and can be used to predict contact characteristics in gait., (© 2024. International Federation for Medical and Biological Engineering.)

Background: Adolescent idiopathic scoliosis (AIS) is a three-dimensional structural asymmetry of the spine and trunk affecting 2-4% of adolescents. Standard treatment is observation, bracing, and surgery for small, moderate, and large curves, respectively. Schroth exercises aim to correct posture and reduce curve progression., Purpose: This study aimed to determine the effect of Schroth exercises added to the standard care compared to standard care alone on torso asymmetry in AIS., Methods: In a randomized controlled trial (NCT01610908), 124 participants with AIS (age: 10-18, Cobb: 10°-45°, Risser: ≤3) were randomly assigned to the control (Standard care only) or Schroth (Standard care + Schroth treatment) group. Schroth treatment consisted of 1-hour weekly supervised sessions and 30-45 minutes of daily home exercises for six months. The control group received Schroth exercises in the last six months of the 1-year monitoring period. Markerless 3D surface topography assessed torso asymmetry measured by maximum deviation (MaxDev) and root mean square (RMS). Intention to treat linear mixed effects model analysis was compared to the per protocol analysis., Results: In the intention to treat analysis, the Schroth group (n = 63) had significantly larger decreased RMS (-1.2 mm, 95%CI [-1.5,-0.9]mm, p = 0.012) and MaxDev (-1.9mm, 95%CI [-2.4,-1.5]mm, p = 0.025) measurements compared to controls (n = 57) after six months of intervention. In the per protocol analysis (Schroth n = 39, control n = 36), the Schroth group also had a significantly larger decrease compared to the control in both the RMS (-1.0mm, 95%CI [-1.9, -0.2]mm, p = 0.013) and MaxDev measurements (-2.0mm, 95%CI [-3.3,-0.5]mm, p = 0.037). For the control group, both the intention to treat and per protocol analysis showed no difference in RMS and MaxDev in the last six months of Schroth intervention (p>0.5)., Conclusion: Schroth Exercise treatment added to standard care (observation or bracing) reduced asymmetry measurements in AIS. As expected, a greater effect was observed for participants who followed the prescribed exercise treatment per protocol., Competing Interests: The authors of this manuscript have the following competing interests: Dr. Parent is a Schroth certified therapist. Dr. Schreiber became an International Schroth Scoliosis Therapy (ISST) instructor and opened the Curvy Spine clinic after the data for this project had been collected. This does not alter our adherence to PLOS ONE policies on sharing data and materials., (Copyright: © 2024 Mohamed et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

Purpose: Comprehensive understanding of force plate parameters distinguishing individuals postprimary anterior cruciate ligament reconstruction (ACLR) from healthy controls during countermovement jumps (CMJ) and/or drop jumps (DJ) is lacking. This review addresses this gap by identifying discriminative force plate parameters and examining changes over time in individuals post-ACLR during CMJ and/or DJ., Methods: We conducted a systematic review and meta analyses following the Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) guidelines. Nine databases were searched from inception to March 2022. We included cross-sectional papers comparing post-ACLR with healthy controls or longitudinal studies of individuals at least 6 months postprimary ACLR while performing CMJ and/or DJ on force plates. The methodological quality was appraised using the Modified Downs and Black Checklist., Results: Thirty-three studies including 1185 (50.38%) participants post-ACLR, and 1167 (49.62%) healthy controls, were included. Data were categorised into single-leg CMJ, double-leg CMJ, single-leg DJ, and double-leg DJ. Jump height was reduced in both single (mean difference [MD] = -3.13; p  < 0.01; 95% confidence interval [CI]: [-4.12, -2.15]) and double-leg (MD = -4.24; p  < 0.01; 95% CI: [-5.14, -3.34]) CMJs amongst individuals with ACLR. Similarly, concentric impulse and eccentric/concentric impulse asymmetry could distinguish between ACLR (MD = 3.42; p  < 0.01; 95% CI: [2.19, 4.64]) and non-ACLR (MD = 5.82; p  < 0.01; 95% CI: [4.80, 6.80]) individuals. In double-leg DJs, peak vertical ground reaction forces were lower in the involved side (MD = -0.10; p  = 0.03; 95% CI: [-0.18, -0.01]) but higher in the uninvolved side (MD = 0.15; p  < 0.01; 95% CI: [0.10, 0.20]) when compared to controls and demonstrated significant changes between 6 months and 3 years post-ACLR., Conclusion: This study identified discriminative kinetic parameters when comparing individuals with and without ACLR and also monitored neuromuscular function post-ACLR. Due to heterogeneity, a combination of parameters may be required to better identify functional deficits post-ACLR., Level of Evidence: Level III., Competing Interests: The authors declare no conflict of interest., (© 2024 The Author(s). Journal of Experimental Orthopaedics published by John Wiley & Sons Ltd on behalf of European Society of Sports Traumatology, Knee Surgery and Arthroscopy.)

Purpose: Despite the significance and complexity of tongue reconstruction surgery, a digital tool for flap design is currently lacking. This study investigates the effectiveness of employing inverse finite element method (IFEM) for meticulously designing the geometric characteristics of harvested tissue (free flap) for tongue reconstruction., Methods: In the case of an artificially simulated hemiglossectomy, IFEM algorithm was applied for algorithmic flap design. The method's effectiveness was evaluated by assessing flap deformation in a simplified virtual reconstruction, focusing on parameters such as stress, strain, and thickness., Results: The IFEM algorithm successfully generated an optimal flap design for the intended surgical removal. Analysis of the flap's overall surface area, deformation characteristics, and safety margins demonstrated the feasibility of the deformation. Notably, the stress and thickness assessments suggested that the flap's tension post-surgery would not adversely affect the mobility of the reconstructed tongue, suggesting a positive outcome for functional recovery., Conclusion: The IFEM demonstrates significant potential as a tool for precise free flap design in tongue reconstruction surgeries. Its application could lead to improved surgical accuracy and better quality of life for patients undergoing such procedures., (© 2024. CARS.)

A non-invasive method of quantitatively assessing dental implant stability is important to monitor its long-term health. The Advanced System for Implant Stability Testing (ASIST) is a noninvasive technique that couples the impact technique with a linear vibration model of the implant system, such that the measured signal can be used to determine a matching analytical response. The purpose of this study was to evaluate the ASIST technique by comparing stability estimates obtained from artificial implant installations with various abutments. Two Straumann dental implants were installed in four densities of uniform polyurethane foam, and the stability of each installation was measured using different healing abutments and artificial dental crowns. With the ASIST, values for the estimated interfacial stiffness increased with foam density and did not significantly change with abutment type for a specific sample. This provides evidence that the analytical model is representative of the physical system. Current methods, such as resonance frequency analysis, interpret the interface stiffness based on a single frequency measurement. With the ASIST, the measured signal provides information about the first and second modes of vibration of the implant system, both of which are influenced by the properties of the corresponding abutment. The consideration of both modes allows the technique to reliably measure the interfacial stiffness independently of the system components. As a result, the ASIST technique may provide an improved non-invasive method of measuring the stability of dental implants., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

The common practice of freezing meniscal allograft tissue is limited due to the formation of damaging ice crystals. Vitrification, which eliminates the formation of damaging ice crystals, may allow the mechanical properties of meniscal allograft tissue to be maintained during storage and long-term preservation. The primary objective of this study was to investigate the differences between fresh, frozen, and vitrified porcine lateral menisci examining compressive mechanical properties in the axial direction. Unconfined compressive stress-relaxation testing was conducted to quantify the mechanical properties of fresh, frozen and vitrified porcine lateral menisci. The compressive mechanical properties investigated were peak and equilibrium stress, secant, instantaneous and equilibrium modulus, percent stress-relaxation, and relaxation time constants from three-term Prony series. Frozen menisci exhibited inferior compressive mechanical properties in comparison with fresh menisci (significant differences in peak and equilibrium stress, and secant, instantaneous and equilibrium modulus) and vitrified menisci (significant differences in peak stress, and secant and instantaneous modulus). Interestingly, fresh and vitrified menisci exhibited comparable compressive mechanical properties (stress, modulus and relaxation parameters). These findings are significant because (1) vitrification was successful in maintaining mechanical properties at values similar to fresh menisci, (2) compressive mechanical properties of fresh menisci were characterized providing a baseline for future research, and (3) freezing affected mechanical properties confirming that freezing should be used with caution in future investigations of meniscal mechanical properties. Vitrification was superior to freezing for preserving compressive mechanical properties of menisci which is an important advance for vitrification as a preservation option for meniscal allograft transplantation., (© 2022. The Author(s), under exclusive licence to Springer Nature B.V.)

Background: Tooth extraction is a common surgical procedure where the invasiveness of the surgery can affect the nature of the dentoalveolar remodelling which follows. However, there is very little biomechanical data relating the loading applied during tooth extraction to the outcomes of the procedure. The purpose of this pilot study is to present a novel ex vivo experimental method for measuring tooth extraction mechanics and to explore preliminary metrics for predicting extraction success., Methods: A custom experimental apparatus was developed in-house to extract central incisors from ex vivo swine mandible samples. Twenty-five (n = 25) incisors were extracted at different rates in displacement- and force-control, along with an intermittent ramp-hold scheme for a total of five schemes. Peak forces and extraction success were recorded for each test. Video analysis assisted in determining the instantaneous stiffnesses of the dental complex during continuous extractions, which were compared using the K-means clustering algorithm., Findings: Tooth extraction forces ranged from 102 N to 309 N, with higher-rate tests tending towards higher peak forces (141 N - 308 N) than the lower-rate tests (102 N-204 N) for displacement- and force-controlled schemes. The K-means algorithm clearly identified load rates among tests, indicating that higher-rate loading increased system stiffness relative to the lower-rate tests., Interpretation: The developed experimental method demonstrated a desirable degree of control. The preliminary results suggest the influence of load rate on the mechanical response of the dental complex and extraction outcome. Future work will further investigate the biomechanics of tooth extraction and relate them to tissue damage to improve future tooth extraction procedures., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Artificial implant materials may articulate against native articular cartilage in certain clinical scenarios and the selection of an implant material that results in the least wear on articular cartilage is preferred to maintain normal joint architecture and function. This project compared the wear on porcine femoral condyles induced by articulation against porcine patellae, titanium alloy (Ti6Al4V), ultra high molecular weight polyethylene (UHMWPE), and carbon fibre reinforced polyether-ether-ketone (CFR-PEEK) through an ex vivo experimental setup. A sinusoidal compressive load of 30-160 N, representing an approximate joint pressure of 0.19-1 MPa at a frequency of 3 Hz coupled with a rotational displacement of +/- 10⁰ at 3 Hz was used to simulate physiological joint motion. Wear was characterized via gross examination and histologically using the OARSI scoring system after 43,200 cycles. CFR-PEEK resulted in the most significant wear on articular cartilage compared to titanium alloy and UHMWPE whereas titanium alloy and UHMWPE resulted in similar levels of wear. All materials caused more wear compared to cartilage-on-cartilage testing. The wear mechanism was characterized by progressive loss of proteoglycan content in cartilage in histology samples., Competing Interests: Declaration of Competing Interest None., (Copyright © 2023. Published by Elsevier Ltd.)

Osteochondral allograft transplantations are typically used to treat focal articular cartilage injuries where the damaged cartilage is replaced with fresh cadaveric donor grafts. Despite the notable success rate of this procedure, it is limited by fresh donor tissue availability which can only be stored for approximately 28 days after harvest. Vitrification, a form of cryopreservation, can extend the storage time of cartilage. Although it has shown to preserve chondrocyte viability, its effect on the mechanical properties of the tissue has not been thoroughly investigated. Therefore, in this study, the mechanical properties of fresh, frozen, and vitrified articular cartilage were evaluated through unconfined compression testing. Results showed that the peak modulus, equilibrium modulus, and relaxation time constants of the vitrified and control samples (tested one day after harvest) were similar and higher than the fresh (tested 21 days after harvest) and frozen samples. This demonstrated that vitrification does not adversely affect the mechanical properties of cartilage and can be used as an alternative to fresh allografts which are limited by storage time. The fresh samples also had inferior mechanical properties compared to the control samples suggesting that vitrified allografts could potentially improve clinical outcomes in addition to increasing donor tissue availability., (© 2023. The Author(s) under exclusive licence to Biomedical Engineering Society.)

Posterolateral corner knee injuries are clinically significant, and often require surgical reconstruction. The optimal knee brace following posterolateral corner reconstructions has not yet been determined via clinical nor biomechanical study. We sought to evaluate the stiffness of six types of knee braces to determine the ideal brace type for reducing varus forces, which may have clinical utility for posterolateral corner knee reconstruction rehabilitation. Six different groups of knee braces underwent mechanical testing: cruciate braces, cruciate braces with a valgus bend, medial unloaders, articulating sleeves, hinged braces, and tri-panel immobilizers. Each brace was fitted to the same fiberglass leg model and was secured to the testing apparatus. Force was applied under four-point bending to generate a varus moment about the artificial knee. The stiffness in Newtons per millimeter (N/mm) of each brace was calculated from the slope of the force-displacement curve. The cruciate brace with a valgus bend had the highest average stiffness at 192.61 N/mm (SD 28.53). The articulating sleeve was the least stiff with an average stiffness of 49.86 N/mm (SD 8.99). Stiffness of the cruciate brace was not statistically different compared to cruciate valgus ( p  = 0.083) or medial unloader ( p  = 0.098). In this experimental design, a cruciate brace with a valgus bend was shown to have the highest overall stiffness, while an articulating sleeve had the lowest stiffness. Future work will investigate whether this translates into clinical performance.

Background  Graft preparation techniques for the Adams-Berger distal radioulnar joint (DRUJ) reconstruction vary among surgeons with insufficient evidence to support any specific technique. Questions/Purposes  We compared survival with cyclic loading, absolute elongation, elongation rate, and modes of failure of four graft preparation techniques. Methods  Fifteen porcine extensor tendons were divided into three equal groups: tendon only; tendon augmented along its full length with nonlocking 2-0 FiberLoop suture spaced at 6 mm intervals; and tendon with suture at 12 mm intervals. Suture only was also tested. Samples were woven through custom radius- and ulna-simulating jigs mounted on a mechanical testing machine. Samples underwent a staircase cyclic loading protocol and were then inspected visually for the mode of failure. Survival with cyclic loading, absolute elongation, and elongation rate was compared. Results  Average survival with cyclic loading of suture-augmented tendon was significantly higher than tendon only. All tendon groups had significantly higher survival compared with suture only. Absolute elongation was subject to variability due to initial nonlinear elongation behavior of samples. The elongation rate was significantly lower with suture compared with all tendon groups. Modes of failure included rupture of the tendon and/or suture at the simulated graft-bone interface and elongation of the entire construct without rupture. Conclusions  In this biomechanical study, augmentation of porcine tendons with suture spaced at either 6 or 12 mm for DRUJ reconstruction significantly increased survival to a staircase cyclic loading protocol Clinical Relevance  For the Adams-Berger reconstruction, tendon grafts augmented along their entire length by nonabsorbable braided suture are biomechanically superior to tendon alone., Competing Interests: Conflict of Interest The FiberLoop sutures used for this study were donated by Arthrex Inc., (Thieme. All rights reserved.)

Cartilage tissue engineering aims to generate functional replacements to treat cartilage defects from damage and osteoarthritis. Human bone marrow-derived mesenchymal stem cells (hBM-MSC) are a promising cell source for making cartilage, but current differentiation protocols require the supplementation of growth factors like TGF-β1 or -β3. This can lead to undesirable hypertrophic differentiation of hBM-MSC that progress to bone. We have found previously that exposing engineered human meniscus tissues to physiologically relevant conditions of the knee (mechanical loading and hypoxia; hence, mechano-hypoxia conditioning) increased the gene expression of hyaline cartilage markers, SOX9 and COL2A1 , inhibited hypertrophic marker COL10A1 , and promoted bulk mechanical property development. Adding further to this protocol, we hypothesize that combined mechano-hypoxia conditioning with TGF-β3 growth factor withdrawal will promote stable, non-hypertrophic chondrogenesis of hBM-MSC embedded in an HA-hydrogel. We found that the combined treatment upregulated many cartilage matrix- and development-related markers while suppressing many hypertrophic- and bone development-related markers. Tissue level assessments with biochemical assays, immunofluorescence, and histochemical staining confirmed the gene expression data. Further, mechanical property development in the dynamic compression treatment shows promise toward generating functional engineered cartilage through more optimized and longer culture conditions. In summary, this study introduced a novel protocol to differentiate hBM-MSC into stable, cartilage-forming cells., Competing Interests: The author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article., (© The Author(s) 2023.)

Abstract: Stadnyk, M, Sepehri, M, Cook, M, Adeeb, S, and Westover, L. Quantifying asymmetry and performance of lower limb mechanical muscle function in varsity athletes-using non-countermovement jumps. J Strength Cond Res 37(1): 98-106, 2023-The ability to automatically quantify jump performance and lower limb muscle function in athletes would be beneficial for both training and rehabilitation purposes. Countermovement jumps (CMJs) and non-CMJs (NCMJs) are simple, quick, and require relatively inexpensive equipment to effectively and reliably monitor lower limb function. In a previous study, CMJ characteristics were assessed across different varsity sports. This study is a follow-up study to incorporate NCMJs into assessing jump characteristics of the same sports and investigate the additional information provided by the complementary jump type. The main objective of this study was to look at a means of quantifying the lower limb mechanical muscle function automatically to provide information for rehabilitation and performance purposes in athletes of specific sports. Male and female varsity athletes from 4 different sports completed 5 trials of an NCMJ on dual force plates. An analysis program was developed using Wolfram Mathematica to analyze force-time jump data. Various parameters of interest were generated, including peak force, force-time curve shape classification, jump phase lengths, phase-specific kinetic impulse, asymmetry index, takeoff velocity, jump height, phase-specific center of mass displacements, and reactive strength index modified. Results obtained indicate that similar jump characteristics to the CMJ study can be quantified, which can be used for performance enhancement or injury rehabilitation. Additional data found, such as the ability of an athlete to hold a steady squat during an NCMJ, could also be meaningful in aiding trainers to design programs tailored for athletes., (Copyright © 2022 National Strength and Conditioning Association.)

Osteoarthritis (OA) primarily affects mechanical load-bearing joints, with the knee being the most common. The prevalence, burden and severity of knee osteoarthritis (KOA) are disproportionately higher in females, but hormonal differences alone do not explain the disproportionate incidence of KOA in females. Mechanical unloading by spaceflight microgravity has been implicated in OA development in cartilaginous tissues. However, the mechanisms and sex-dependent differences in OA-like development are not well explored. In this study, engineered meniscus constructs were generated from healthy human meniscus fibrochondrocytes (MFC) seeded onto type I collagen scaffolds and cultured under normal gravity and simulated microgravity conditions. We report the whole-genome sequences of constructs from 4 female and 4 male donors, along with the evaluation of their phenotypic characteristics. The collected data could be used as valuable resources to further explore the mechanism of KOA development in response to mechanical unloading, and to investigate the molecular basis of the observed sex differences in KOA., (© 2022. The Author(s).)

Background: The use of particulated articular cartilage for repairing cartilage defects has been well established, but its use is currently limited by the availability and short shelf life of donor cartilage. Vitrification is an ice-free cryopreservation technology at ultralow temperatures for tissue banking. An optimized vitrification protocol has been developed for particulated articular cartilage; however, the equivalency of the long-term clinical efficacy of vitrified particulated articular cartilage compared with fresh articular cartilage has not yet been determined., Hypothesis: The repair effect of vitrified particulated cartilage from pigs would be equivalent to or better than that of fresh particulated cartilage stored at 4°C for 21 days., Study Design: Controlled laboratory study., Methods: A total of 19 pigs were randomly divided into 3 experimental groups: fresh particulated cartilage group (n = 8), vitrified particulated cartilage group (n = 8), and negative control group (no particulated cartilage in the defect; n = 3). An additional pig was used as the initial cartilage donor for the first set of surgical procedures. Pigs were euthanized after 6 months to obtain femoral condyles, and the contralateral condyle was used as the positive (no defect) control. Samples were evaluated for gross morphology using the Outerbridge and Osteoarthritis Research Society International (OARSI) scoring systems, histology (safranin O, collagen type I/II, DAPI), and chondrocyte viability using live-dead membrane integrity staining., Results: There were no infections after surgery, and all 19 pigs were followed for the duration of the study. The OARSI grades for the fresh and vitrified particulated cartilage groups were 2.44 ± 1.35 and 2.00 ± 0.80, respectively, while the negative control group was graded significantly higher at 4.83 ± 0.29. Analysis of histological and fluorescent staining demonstrated that the fresh and vitrified particulated cartilage groups had equivalent regeneration within cartilage defects, with similar cell viability and densities and expression of proteoglycans and collagen type I/II., Conclusion: The implantation of fresh or vitrified particulated cartilage resulted in the equivalent repair of focal cartilage defects when evaluated at 6 months after surgery., Clinical Relevance: The vitrification of particulated cartilage is a viable option for long-term storage for cartilage tissue banking and could greatly increase the availability of donor tissue for transplantation.

The dynamic behavior of osseointegrated implants can be used for the non-invasive evaluation of the condition of the bone-implant-interface (BII). The Advanced System for Implant Stability Testing (ASIST) is a vibration measurement system that relies on an impact technique and an analytical model to compute the interface stiffness and the ASIST stability coefficient ([Formula: see text]). The objective of this work is to develop a finite element (FE) model capable of capturing the dynamic behaviour of the bone-anchored hearing aid under the ASIST loading condition. The model was validated with previously collected in vitro and in vivo data which were compared to the model's acceleration responses and [Formula: see text] scores. Similar acceleration responses were obtained, and the maximum absolute differences in [Formula: see text] scores between the FE model and the in vitro and in vivo data were 1.15% and 5.48% respectively. The model was then used to show the existence of a relationship between the rod's acceleration response and the BII stress field. Finally, the model was used to interpret the factors that affect the stiffness parameters of the ASIST analytical model. The interface stiffness and the system's dynamic properties were more influenced ([Formula: see text]) by the BII material and friction coefficient compared to the implant geometry. In this work, a finite element model of the bone anchored hearing aid was used to simulate the dynamic behaviour of the bone-implant system under the ASIST's loading conditions. The model was first validated with previously collected experimental and clinical results. The validated model was then used to study the relationship between the impact rod's acceleration response and the response at the bone implant interface. Finally, the model was used to formulate a better understanding on the influencing factors on the interface stiffness., (© 2022. International Federation for Medical and Biological Engineering.)

Vitrification inhibits crystallization of ice and may allow the mechanical properties of menisci to be preserved for transplantation without the damaging consequences of ice crystals formed during freezing. The primary objective of this study was to investigate the differences between fresh, frozen, and vitrified porcine lateral menisci examining tensile mechanical properties along the circumferential-peripheral, circumferential-central, longitudinal, and radial orientations. The secondary objective was to investigate the variations in the tensile mechanical properties of menisci comparing the circumferential-peripheral orientation to the three other orientations: circumferential-central, longitudinal, and radial. Quasi-static tensile testing was conducted to quantify the tensile mechanical properties of fresh, frozen and vitrified menisci. Ultimate tensile strength of frozen menisci were significantly decreased compared with fresh and vitrified menisci along three orientations: circumferential-peripheral, longitudinal, and radial. Along the circumferential-central orientation, tensile modulus of frozen menisci was significantly decreased compared with fresh menisci. The mechanical properties of vitrified menisci were comparable to fresh menisci along all four orientations. For all menisci (fresh, frozen and vitrified), ultimate tensile strength and failure strain along the circumferential-peripheral orientation were significantly increased compared with the three other orientations. Freezing was detrimental to the mechanical properties of menisci but vitrification likely avoided the negative effects of freezing thereby preserving mechanical properties that were comparable to fresh menisci. The findings of this study revealed that vitrification was superior to freezing for preserving mechanical properties of meniscal tissue; hence, vitrification is likely to be a competitive alternative to freezing for meniscal transplantation in the future., Competing Interests: Declaration of Competing Interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Dr. N. M. Jomha is a co-inventor on US and Canadian patents for articular cartilage preservation: Jomha, N. M., McGann, L. E., Elliott, J. A. W., Law, G., Forbes, F., Torgabeh, A. A., Maghdoori, B., Weiss, A., University of Alberta, 2014. “Cryopreservation of articular cartilage”. US Patent 8,758,988; Canada 2,788,202., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Articular cartilage (AC) injuries do not heal primarily and large lesions progress to degenerative osteoarthritis. Osteochondral allograft transplantation is an effective surgical treatment but is limited by the lack of donor tissue availability. Fresh allografts can be stored hypothermically up to 28-45 days after which the tissue is no longer viable for transplantation. Vitrification is a method of cryopreservation with the potential to extend the storage time of AC. A specific protocol has been demonstrated to preserve high chondrocyte viability; however, its effect on various mechanical properties of the extracellular matrix (ECM) remains unknown and is the focus of this initial study. Porcine AC was subject to a defined vitrification protocol, using fresh and frozen samples as positive and negative controls, respectively; n  = 20 for all three groups. Unconfined compression testing was used to assess mechanical properties of the tissue under rapid load, stress relaxation, and equilibrium conditions. The stress relaxation time constants (modeled with a 2-term Prony series) τ 1 and τ 2 were significantly lower for frozen ( p  = 0.014, p  < 0.001) and vitrified ( p  = 0.009, p  = 0.003) tissue compared to fresh, with no differences between frozen and vitrified samples ( p  = 0.848 and 0.105 for τ 1 and τ 2 , respectively). These values indicate that frozen and vitrified samples relaxed more rapidly than fresh, which may suggest altered matrix composition and permeability post-treatment. These results represent the initial study in our experimental path to evaluate differences in mechanical properties of vitrified tissues.

This scoping review is intended to synthesize the techniques proposed to model the tooth-periodontal ligament-bone complex (TPBC), while also evaluating the suggested periodontal ligament (PDL) material properties. It is concentrated on the recent advancements on the PDL and TPBC models, while identifying the advantages and limitations of the proposed approaches. Systematic searches were conducted up to December 2020 for articles that proposed PDL models to assess orthodontic tooth movement in Compendex, Web of Science, EMBASE, MEDLINE, PubMed, ScienceDirect, Google Scholar and Scopus databases. Although there have been many studies focused on the evaluation of PDL material properties through numerous modelling approaches, only a handful of approaches have been identified to investigate the interface properties of the PDL as a complete dynamical system (TPBC models). Past reviews on the analytical and experimental determination of the PDL properties already show a concerning range in reported output values-some nearly six orders of magnitude in difference-that strongly suggested the need for further investigation. Surprisingly, it has not yet been possible to determine a narrower range of values for the PDL material properties. Moreover, very few scientific approaches address the TPBC as an integrated complex system model. In consequence, current methods for capturing the PDL material behaviour in a clinical setting are limited and inconclusive. This synthesis encourages more systematic, pragmatic and phenomenological research in this area., (© 2021 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

The objective is developing an XFEM model that is capable of predicting different types of fracture in the pelvic bone under various loading conditions. Previously published mechanical and failure characteristics of cortical and cancellous tissues were implemented and assigned to an intact pelvic bone with specified cortical and cancellous tissues. Various loading conditions, including combined load directions, were applied to the acetabulum to model different types of fracture (e.g., anterior/posterior wall fracture and transverse fracture) in the pelvic bone. The predicated types of fracture and the maximum force at fracture were compared to those acquired from previously published experimental tests. Anterior/posterior wall fracture and transverse fracture were the most common types of fractures determined in the simulations. The XFEM simulations were able to predict similar fractures to those reported in the experimental tests. The maximum fracture force in the XFEM model was found to be 18.6 kN compared to 8.85 kN reported in the previous experimental tests. The results revealed that different types of fracture in the pelvic bones can be caused by the various loading conditions in unstable high-rate impact loads. Using proper mechanical and failure behaviors of cortical and cancellous tissues, XFEM modeling of pelvic bone is capable of predicting bone fracture. In future work, the XFEM models of cancellous and cortical tissues can be assigned to other bones in human body skeleton so that the failure mechanism in such bones can be investigated.

Purpose: Irradiation of fibular grafts for jaw reconstruction following mandibulectomy can be associated with increased graft failure and implant instability. The objective of this study is to investigate the effect of isolated irradiation on the biomechanical properties of ex-vivo porcine fibula grafts. It was hypothesized that the isolated irradiation (without biological response) will not significantly influence the biomechanical properties of the fibular grafts., Methods: Forty porcine fibular grafts (n = 20 irradiated and n = 20 nonirradiated) were obtained. The irradiated group was subjected to a single dose of 60 Gy of irradiation with cesium 137. Both groups underwent 3-point bending tests with cyclic loading for 1500 cycles (50 to 500 N at 2 Hz) followed by push to failure. Rate of damage (mm/s), stiffness (N/mm), modulus of elasticity (MPa), maximum load (N), maximum displacement (mm), and maximum stress (MPa) were compared between the 2 groups using independent t tests (P < .05)., Results: No significant differences were found between the irradiated and nonirradiated groups for any of the biomechanical parameters (all P values > 0.05)., Conclusions: The results of this study support our hypothesis that even high levels of isolated irradiation do not significantly affect the biomechanical properties of fibular bone grafts. This work allows us to exclude acute structural changes in the bone due to irradiation as a possible factor leading to bone/implant instability following jaw reconstruction with fibular grafts. Further studies need to be conducted to better understand the range of factors that may lead to implant instability, including the biological response after radiation therapy., (Copyright © 2021 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)

Customized talus implants have been regarded as a better treatment alternative to talus avascular necrosis than traditional surgical fusion because of its ability to maintain joint mobility while ameliorating pain. Despite the use of ankle hemiarthroplasty clinically, the cartilage contact characteristics of adjacent bones remain unclear. This study aims to use finite element modeling to evaluate the contact characteristics of three types of cobalt-chrome talus implants in three postures, in four subjects. This study also compared the contact area, contact pressure, and peak contact pressure of the implant models with a reference biological model. Among the various biological and implant models, our results showed that the biological models generally had the largest contact areas and smallest peak contact pressures, whereas the implant-type models had smaller contact areas and relatively larger peak contact pressure. Moreover, among the three implant types, customized-scale models showed a larger total contact area than that of the SSM-scale and universal-scale models, but their variation was relatively limited. The results from this study can have significance in future endeavors into ankle joint modeling, as well as being able to improve implant design to enhance recovery outcomes for patients who may benefit from talar replacement., (© 2022. International Federation for Medical and Biological Engineering.)

Background: Osteoarthritis (OA) primarily affects mechanical load-bearing joints. The knee joint is the most impacted by OA. Knee OA (KOA) occurs in almost all demographic groups, but the prevalence and severity are disproportionately higher in females. The molecular mechanism underlying the pathogenesis and progression of KOA is unknown. The molecular basis of biological sex matters of KOA is not fully understood. Mechanical stimulation plays a vital role in modulating OA-related responses of load-bearing tissues. Mechanical unloading by simulated microgravity (SMG) induced OA-like gene expression in engineered cartilage, while mechanical loading by cyclic hydrostatic pressure (CHP), on the other hand, exerted a pro-chondrogenic effect. This study aimed to evaluate the effects of mechanical loading and unloading via CHP and SMG, respectively, on the OA-related profile changes of engineered meniscus tissues and explore biological sex-related differences. Methods: Tissue-engineered menisci were made from female and male meniscus fibrochondrocytes (MFCs) under static conditions of normal gravity in chondrogenic media and subjected to SMG and CHP culture. Constructs were assayed via histology, immunofluorescence, GAG/DNA assays, RNA sequencing, and testing of mechanical properties. Results: The mRNA expression of ACAN and COL2A1 , was upregulated by CHP but downregulated by SMG. COL10A1 , a marker for chondrocyte hypertrophy, was downregulated by CHP compared to SMG. Furthermore, CHP increased GAG/DNA levels and wet weight in both female and male donors, but only significantly in females. From the transcriptomics, CHP and SMG significantly modulated genes related to the ossification, regulation of ossification, extracellular matrix, and angiogenesis Gene Ontology (GO) terms. A clear difference in fold-change magnitude and direction was seen between the two treatments for many of the genes. Furthermore, differences in fold-change magnitudes were seen between male and female donors within each treatment. SMG and CHP also significantly modulated genes in OA-related KEGG pathways, such as mineral absorption, Wnt signalling pathway, and HIF-1 signalling pathway. Conclusion: Engineered menisci responded to CHP and SMG in a sex-dependent manner. SMG may induce an OA-like profile, while CHP promotes chondrogenesis. The combination of SMG and CHP could serve as a model to study the early molecular events of KOA and potential drug-targetable pathways., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Ma, Li, Kunze, Mulet-Sierra, Westover and Adesida.)

Talus implants can be utilized in cases of talus avascular necrosis and has been regarded as a promising treatment method. However, existing implants are made of stiff materials that directly oppose natural cartilage. The risk of long-term cartilage wear and bone fracture from the interaction between the cartilage and stiff implant surfaces has been documented in post-hemiarthroplasty of the hip, knee and ankle joints. The aim is to explore the effects of adding a layer of compliant material (polycarbonate-urethane; PCU) over a stiff material (cobalt chromium) in talus implants. To do so, we obtained initial ankle geometry from four cadaveric subjects in neutral standing to create the finite element models. We simulated seven models for each subject: three different types of talus implants, each coated with and without PCU, and a biological model. In total, we constructed 28 finite element models. By comparing the contact characteristics of the implant models with their respective biological model counterparts, our results showed that PCU coated implants have comparable contact area and contact pressure to the biological models, whereas stiff material implants without the PCU coating all have relatively higher contact pressure and smaller contact areas. These results confirmed that adding a layer of compliant material coating reduces the contact pressure and increases the contact area which in turn reduces the risk of cartilage wear and bone fracture. The results also suggest that there can be clinical benefits of adding a layer of compliant material coating on existing stiff material implants, and can provide valuable information towards the design of more biofidelic implants in the future., (Copyright © 2021 Elsevier Ltd. All rights reserved.)