Search

In memory semiconductors such as a static random access memory (SRAM), a common problem is soft errors under radiation environment. These soft errors cause bit flips, which are referred to as single event upsets (SEUs). Some radiation-hardened SRAM cells such as a Quatro SRAM, we-Quatro SRAM, and DICE SRAM cells have been reported for years. However, these designs have the disadvantage of taking up more area than a conventional 6T SRAM cell. Thus, we propose a radiation-hardened SRAM cell design that we named capacitor-static random access memory (C-SRAM) without area overhead. The C-SRAM is formed by simply adding a capacitor to the conventional 6T SRAM. It was designed to mitigate the radiation effect using the conservation law of electrical charge. Moreover, it has the same cell size as the conventional 6T SRAM cell. Its static noise margins (SNMs), which are indicators of operational stability, are equal to the conventional 6T SRAM values of 530 mV, 220 mV, and 860 mV in hold, read, and write modes, respectively. The results of the SEU simulation test showed that it had 4.761 times better flipping tolerance than the conventional 6T SRAM with a charge value of 247.494 fC. In addition, irradiation experiments also confirmed that the C-SRAM cell was more tolerant than the 6T SRAM cell. The conventional 6T SRAM and C-SRAM were fabricated using a standard 0.18 μm CMOS process.

This paper presents a radiation-hardened-by-design preamplifier that utilizes a self-compensation technique with a charge-sensitive amplifier (CSA) and replica for total ionizing dose (TID) effects. The CSA consists of an operational amplifier (OPAMP) with a 6-bit binary weighted current source (BWCS) and feedback network. The replica circuit is utilized to compensate for the TID effects of the CSA. Two comparators can detect the operating point of the replica OPAMP and generate appropriate signals to control the switches of the BWCS. The proposed preamplifier was fabricated using a general-purpose complementary metal-oxide-silicon field effect transistor 0.18 μm process and verified through a test up to 230 kGy (SiO2) at a rate of 10.46 kGy (SiO2)/h. The code of the BWCS control circuit varied with the total radiation dose. During the verification test, the initial value of the digital code was 39, and a final value of 30 was observed. Furthermore, the preamplifier output exhibited a maximum variation error of 2.39%, while the maximum rise-time error was 1.96%. A minimum signal-to-noise ratio of 49.64 dB was measured.

This paper proposes an effective method to improve the power efficiency of the flyback converter in the continuous conduction mode (CCM). The proposed converter uses a simple passive circuit to reduce the switching power losses. The current through the output diode can be shifted to a new branch where one diode, one inductor, and one auxiliary winding of the transformer are included. The output diode current can be reduced to zero for the zero-current switching of the output diode. The additional inductor is used to control the changing rate of the additional diode current to reduce the reverse-recovery current. Keeping the simplicity of the passive method, the proposed converter improves the power efficiency compared to the conventional converter. The circuit configuration and the operation principle are described. The design considerations are presented, including the simulation verification. The experimental results for a 45 W prototype are discussed to evaluate the performance of the proposed converter. The proposed converter has achieved a power efficiency of 93.5% for the rated load condition, improving the power efficiency. The applications of the proposed converter are also discussed for the future research directions.

We propose a novel double stripe structure for achieving a narrow far-field angle without significant output power loss in narrow-ridge high-power broad-area laser diodes. By introducing double SiO2 stripes on the top side of the laser diode, we effectively suppress high-order modes through mode weight engineering. Through self-consistent electro-thermal-optical simulations powered by LASTIP with the well-verified model from the reference, we comprehensively analyze and compare the characteristics of high-power broad-area laser diodes utilizing the loss tailoring technique that adopted the much simpler structure compared to prior study and our proposed structure. Our results demonstrate a significant reduction of approximately 36% in the far-field angle while maintaining slope efficiency. This approach shows promise for enhancing the performance of coupling efficiency between narrow-ridge high-power laser diodes and fibers.

We demonstrate an FPGA-based controller for Si MZI-based Spanke-Benes 4 × 4 optical switch fabric that can automatically calibrate each individual switching cell and select the desired routing configuration. In order to minimize the power consumption for optical switching operation, the optimal heater voltages for the cross and the bar state of each switching cell is determined during the calibration. The operation of our controller is successfully verified with a Si MZI-based Spanke-Benes 4 × 4 optical switch.

This paper proposes a step-up DC–DC converter for a power electronic circuit for standalone photovoltaic systems with battery energy storages. The proposed DC–DC converter effectively converts low DC battery voltage into high DC-link voltage. It operates with soft-switching characteristics, which can reduce switching power losses. The proposed converter operates without output voltage feedback, which simplifies its control design. The operation principle of the proposed converter was described, along with the overall system configuration. The experimental results were discussed for the 500-W prototype system using a 12-V lead-acid battery.

Electronic devices based on negative differential resistance hold promise for multi-valued logic applications. Here, the authors implement such functionalities using an atomically thin phosphorene/rhenium disulfide van der Waals heterostructure, and further demonstrate the implementation of a ternary inverter.

The conventional zeta inverter has been used for single-phase grid-connected applications. However, it has high switching losses to operate at high switching frequency in the continuous conduction mode (CCM). To address this drawback, this paper suggests a high-efficiency zeta inverter using active clamp and synchronous rectification techniques. The proposed inverter utilizes the active clamp circuit for reducing switching losses. The non-complementary switching scheme is adopted for not only clamping the switch voltage stresses, but also alleviating the circulating energy. In addition, the synchronous rectification is implemented for reducing the body diode conduction of power switches. By using the silicon carbide (SiC) metal oxide semiconductor field effect transistors (MOSFETs), the switching performance of the proposed inverter is improved. Its operation principle and control strategy are presented. A 220-W prototype has been designed and tested to evaluate the performance of the proposed inverter.

This paper introduces SNUMAX, the grand winner of the RoboSoft Grand Challenge. SNUMAX was built to complete all the tasks of the challenge. Completing these tasks required robotic compliant components that could adapt to variable situations and environments and generate enough stiffness to maintain performance. SNUMAX has three key components: transformable origami wheels, a polymer-based variable stiffness manipulator, and an adaptive caging gripper. This paper describes the design of these components and how they worked together to allow the robot to perform the contest’s navigation and manipulation tasks.

To identify oseltamivir resistance, we analyzed neuraminidase H275Y mutations in samples from 10 patients infected with pandemic (H1N1) 2009 virus in South Korea who had influenza that was refractory to antiviral treatment with this drug. A neuraminidase I117M mutation that might influence oseltamivir susceptibility was detected in sequential specimens from 1 patient.

Among vertebrate species, pigs are a major amplifying host of Japanese encephalitis virus (JEV) and measuring their seroconversion is a reliable indicator of virus activity. Traditionally, the hemagglutination inhibition test has been used for serological testing in pigs; however, it has several limitations and, thus, a more efficient and reliable replacement test is required. In this study, we developed a new immunochromatographic test for detecting antibodies to JEV in pig serum within 15 min. Specifically, the domain III region of the JEV envelope protein was successfully expressed in soluble form and used for developing the immunochromatographic test. The test was then applied to the surveillance of Japanese encephalitis (JE) in Korea. We found that our immunochromatographic test had good sensitivity (84.8%) and specificity (97.7%) when compared with an immunofluorescence assay used as a reference test. During the surveillance of JE in Korea in 2012, the new immunochromatographic test was used to test the sera of 1,926 slaughtered pigs from eight provinces, and 228 pigs (11.8%) were found to be JEV-positive. Based on these results, we also produced an activity map of JEV, which marked the locations of pig farms in Korea that tested positive for the virus. Thus, the immunochromatographic test reported here provides a convenient and effective tool for real-time monitoring of JEV activity in pigs.

This paper presents a novel approach to the correction of zygomatic malposition and secondary reconstruction orbital floor fractures, highlighting the use of hydrated acellular dermal matrix (ADM), specifically CGDerm One-Step, in a case where traditional solid implants failed to maintain structural integrity and volume. A 27-year-old woman with persistent facial deformities following a traumatic incident underwent a transformative procedure that utilized ADM for volume correction and structural support, addressing significant challenges such as enophthalmos and facial contour depression. This approach was necessitated by the descent of the entire orbital floor and a previously placed implant (Medpor), leading to unsatisfactory volume correction. By integrating ADM with titanium-reinforced fan plates (Synpor), the surgery successfully restored the patient's facial symmetry and addressed her functional concerns, including diplopia and limited eye movement. Postoperative evaluations demonstrated the long-term effectiveness of this method, with significant improvements in facial contour and eye symmetry. Our findings suggest that ADM, particularly in its hydrated form, offers a reliable alternative to traditional bone grafts and implants for correcting complex craniofacial deformities, providing both aesthetic and functional benefits. This case underscores the importance of adaptable, tissue-mimicking materials in facial reconstructive surgery, offering insights into their potential for broader application in post-traumatic facial corrections. [ABSTRACT FROM AUTHOR]