Search

High angular resolution imaging by Atacama Large Millimeter/submillimeter Array (ALMA) has revealed the near universality and diversity of substructures in protoplanetary disks. However, disks around M-type pre-main-sequence stars are still poorly sampled, despite the prevalence of M dwarfs in the Galaxy. Here we present high-resolution (∼50 mas, 8 au) ALMA Band 6 observations of six disks around mid-M stars in Taurus. We detect dust continuum emission in all six disks, ^12 CO in five disks, and ^13 CO line in two disks. The size ratios between gas and dust disks range from 1.6 to 5.1. The ratio of about 5 for 2M0436 and 2M0450 indicates efficient dust radial drift. Four disks show rings and cavities, and two disks are smooth. The cavity sizes occupy a wide range: 60 au for 2M0412, and ∼10 au for 2M0434, 2M0436, and 2M0508. Detailed visibility modeling indicates that small cavities of 1.7 and 5.7 au may hide in the two smooth disks 2M0450 and CIDA 12. We perform radiative transfer fitting of the infrared spectral energy distributions to constrain the cavity sizes, finding that micron-sized dust grains may have smaller cavities than millimeter grains. Planet–disk interactions are the preferred explanation to produce the large 60 au cavity, while other physics could be responsible for the three ∼10 au cavities under current observations and theories. Currently, disks around mid- to late M stars in Taurus show a higher detection frequency of cavities than earlier-type stars, although a more complete sample is needed to evaluate any dependence of substructure on stellar mass.

While the most exciting explanation of the observed dust asymmetries in protoplanetary disks is the presence of protoplanets, other mechanisms can also form the dust features. This paper presents dual-wavelength Atacama Large Millimeter/submillimeter Array observations of a large asymmetric dusty ring around the M-type star CIDA 9A. We detect a dust asymmetry in both 1.3 and 3.1 mm data. To characterize the asymmetric structure, a parametric model is used to fit the observed visibilities. We report a tentative azimuthal shift of the dust emission peaks between the observations at the two wavelengths. This shift is consistent with a dust trap caused by a vortex, which may be formed by an embedded protoplanet or other hydrodynamical instabilities, such as a dead zone. Deep high-spatial-resolution observations of dust and molecular gas are needed to constrain the mechanisms that formed the observed millimeter cavity and dust asymmetry in the protoplanetary disk around CIDA 9A.

Planet formation imprints signatures on the physical structures of disks. In this paper, we present high-resolution (∼50 mas, 8 au) Atacama Large Millimeter/submillimeter Array observations of 1.3 mm dust continuum and CO line emission toward the disk around the M3.5 star 2MASS J04124068+2438157. The dust disk consists of only two narrow rings at radial distances of 0.″47 and 0.″78 (∼70 and 116 au), with Gaussian σ widths of 5.6 and 8.5 au, respectively. The width of the outer ring is smaller than the estimated pressure scale height by ∼25%, suggesting dust trapping in a radial pressure bump. The dust disk size, set by the location of the outermost ring, is significantly larger (by 3 σ ) than other disks with similar millimeter luminosity, which can be explained by an early formation of local pressure bump to stop radial drift of millimeter dust grains. After considering the disk’s physical structure and accretion properties, we prefer planet–disk interaction over dead zone or photoevaporation models to explain the observed dust disk morphology. We carry out high-contrast imaging at the $L^{\prime} $ band using Keck/NIRC2 to search for potential young planets, but do not identify any source above 5 σ . Within the dust gap between the two rings, we reach a contrast level of ∼7 mag, constraining the possible planet below ∼2–4 M _Jup . Analyses of the gap/ring properties suggest that an approximately Saturn-mass planet at ∼90 au is likely responsible for the formation of the outer ring, which can potentially be revealed with JWST.

Ti is widely used as a material for orthopedic implants. As rapid and effective osseointegration is a key factor for the successful application of implants, biologically inert Ti materials start to show inherent limitations, such as poor surface cell adhesion, bioactivity, and bone-growth-inducing capabilities. Surface modification can be an efficient and effective approach to addressing the biocompatibility, mechanical, and functionality issues of the various Ti implant materials. In this study, we have overviewed more than 140 papers to summarize the recent progress in the surface modification of Ti implants by physical and/or chemical modification approaches, aiming at optimizing their wear resistance, biocompatibility, and antimicrobial properties. As an advanced manufacturing technology for Ti and Ti alloys, additive manufacturing was particularly addressed in this review. We also provide an outlook for future research directions in this field as a contribution to the development of advanced Ti implants for biomedical applications.