Search

Agricultural workers frequently experience potentially hazardous exposure to non-ionizing radiation from both solar and artificial sources, and measurement of this exposure can be expensive and impractical for large populations. This project develops and evaluates a vegetative radiative transfer model (VRTM) to predict irradiance in a grow room of an indoor cannabis farm. The model uses morphological characteristics of the crop, manufacturer provided lamp emissions data, and dimensional measurements of the grow room and cannabis hedgerows to predict irradiance. A linear regression comparing model predictions with the measurements taken by a visible light spectroradiometer had slopes within 23% of unity and R2 values above 0.88 for visible (400-700 nm), blue (400-500 nm), green (500-600 nm), and red (600-700 nm) wavelength bands. The excellent agreement between the model and the measured irradiance in the cannabis farm grow room supports the potential of using VRTMs to predict irradiance and worker exposure in agricultural settings. Because there is no mechanistic difference between visible and other non-ionizing wavelengths of radiation in regards to mechanisms of radiative transfer, the model developed herein for visible wavelengths of radiation should be generalizable to other radiation bands including infrared and ultraviolet radiation., (© The Author(s) 2023. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.)

Available wearable dosimeters suffer from spectral mismatch during the measurement of broadband UV and visible radiation in environments that receive radiation from multiple sources emitting differing spectra. We observed this type of multi-spectra environment in all five Washington State cannabis farms visited during a field study investigating worker exposure to ultraviolet radiation in 2018. Spectroradiometers do not suffer from spectral mismatch in these environments, however, an extensive literature review conducted at the time of writing did not identify any spectroradiometers that were directly deployable as wearable dosimetry devices. To close this research gap, we developed a microcontroller system and platform that allows for researchers to mount and deploy the Ocean Insight Flame-S Spectroradiometer as a wearable device for measurement of UV and visible wavelengths (300 to 700 nm). The platform validation consisted of comparing measurements taken under platform control with measurements taken with the spectrometer controlled by a personal computer running the software provided by the spectroradiometer manufacturer. Three Mann-Whitney U-Tests (two-tailed, 95% CI), one for each intensity condition, compared the central tendency between the total spectral power (TSP), the integral of a spectrum measurement, measured under both control schemas. An additional analysis of per pixel agreement and overall platform stability was performed. The three Mann-Whitney tests returned no significant difference between the set of TSPs for each filter condition. These results suggest that the spectroradiometer takes measurements of equivalent accuracy under both control schemas, and can be deployed as a wearable device for the measurement of wavelength resolved UV and visible radiation.

Background: Pesticides play an important role in protecting the food supply and the public's health from pests and diseases. By their nature, pesticides can be toxic to unintended target organisms. Changing winds contribute to pesticide drift- the off-target movement of pesticides-and can result in occupational and bystander illness., Methods: We systematically linked historical weather data to documented pesticide drift illnesses. We used Washington State Department of Health data to identify 252 drift events that included 690 confirmed cases of illness from 2000 to 2015. To characterize wind speed and direction at the time of the events, we paired these data with meteorological data from a network of 171 state weather stations. We report descriptive statistics and the spatio-temporal extent of drift events and compare applicator-reported weather conditions to those from nearby meteorological stations., Results: Most drift events occurred in tree fruit (151/252 = 60%). Ground spraying and aerial applications accounted for 68% and 23% of events, respectively; 69% of confirmed cases were workers, and 31% were bystanders. Confirmed cases were highest in 2014 (129) from 22 events. Complete applicator spray records were available for 57 drift events (23%). Average applicator-reported wind speeds were about 0.9 m •sec - 1 (2 mi •hr - 1 ) lower than corresponding speeds from the nearest weather station values., Conclusions: Drift events result from a complex array of factors in the agricultural setting. We used known spatio-temporal aspects of drift and historical weather data to characterize these events, but additional research is needed to put our findings into practice. Particularly critical for this analysis is more accurate and complete information about location, time, wind speed, and wind direction. Our findings can be incorporated into new training materials to improve the practice of pesticide application and for better documentation of spray drift events. A precision agriculture approach offers technological solutions that simplify the task of tracking pesticide spraying and weather conditions. Public health investigators will benefit from improved meteorological data and accurate application records. Growers, applicators, and surrounding communities will also benefit from the explanatory and predictive potential of wind ramping studies.

The Mobile ObserVations of Ultrafine Particles study was a two-year project to analyze potential air quality impacts of ultrafine particles (UFPs) from aircraft traffic for communities near an international airport. The study assessed UFP concentrations within 10 miles of the airport in the directions of aircraft flight. Over the course of four seasons, this study conducted a mobile sampling scheme to collect time-resolved measures of UFP, CO 2 , and black carbon (BC) concentrations, as well as UFP size distributions. Primary findings were that UFPs were associated with both roadway traffic and aircraft sources, with the highest UFP counts found on the major roadway (I-5). Total concentrations of UFPs alone (10-1000 nm) did not distinguish roadway and aircraft features. However, key differences existed in the particle size distribution and the black carbon concentration for roadway and aircraft features. These differences can help distinguish between the spatial impact of roadway traffic and aircraft UFP emissions using a combination of mobile monitoring and standard statistical methods.

Uranium is naturally found in the environment as a radioactive metal element with high concentrations in the Southwestern US. In this region is the Navajo Nation, which spans approximately 69,930 square kilometers. A decay product of uranium is radon gas, a lung carcinogen that has no color, odor, or taste. Radon gas may pass from soil into homes; and, indoor accumulation has been associated with geographical location, seasonality, home construction materials, and home ventilation. A home and indoor radon survey was conducted from November 2014 through May 2015, with volunteers who reported residence on the Navajo Nation. Home geolocation, structural characteristics, temperature (°C) during radon testing, and elevation (meters) were recorded. Short-term indoor radon kits were used to measure indoor radon levels. 51 homes were measured for indoor radon levels, with an arithmetic mean concentration of 60.5 Becquerels per cubic meter (Bq/m 3 ) (SD = 42.7). The mean indoor radon concentrations (Bq/m 3 ) by house type were: mobile, 29.0 (SD = 22.9); wood, 58.6 (SD = 36.0); hogan, 74.0 (SD = 0.0); homes constructed of cement and wood, 82.6 (SD = 3.5); and homes constructed of concrete and cement, 105.7 (SD = 55.8). A key observation is that house construction type appears to be associated with the mean home indoor radon concentration. This observation has been published in that the basic structural make-up of the home may affect home ventilation and therefore indoor radon concentration levels.

The benchmark dose has been frequently recommended for the creation of points of departure for regulatory dose limits, but many regulations, including pesticide risk assessment and registration in the United States, continues to rely on NOAEL methods as the OECD toxicological standard methods recommend. This study used data from studies in support of pesticide registration for eight different compounds to build dose-response models and calculate benchmark doses and confidence limits. The results were compared to the NOAEL of the same study. A probabilistic estimate of dose was compared with all points of departure to demonstrate differences in the protective ability of each different selected limit. While neither the BMD/BMDL nor the NOAEL was consistently more protective, the advantage of using the BMD in quantifying the uncertainty of the point of departure is highlighted, and the feasibility of using current OECD-guideline studies for derivation of a BMD is demonstrated in these cases., (Copyright © 2019 Elsevier Inc. All rights reserved.)

Pesticide spray drift represents an important exposure pathway that may cause illness among orchard workers. To strike a balance between improving spray coverage and reducing drift, new sprayer technologies are being marketed for use in modern tree canopies to replace conventional axial fan airblast (AFA) sprayers that have been used widely since the 1950s. We designed a series of spray trials that used mixed-effects modeling to compare tracer-based drift volume levels for old and new sprayer technologies in an orchard work environment. Building on a smaller study of 6 trials (168 tree rows) that collected polyester line drift samples (n = 270 measurements) suspended on 15 vertical masts downwind of an AFA sprayer application, this study included 9 additional comparison trials (252 tree rows; n = 405 measurements) for 2 airblast tower sprayers: the directed air tower (DAT) and the multi-headed fan tower (MFT). Field-based measurements at mid (26 m) and far (52 m) distances showed that the DAT and MFT sprayers had 4-15 and 35-37% less drift than the AFA. After controlling for downwind distance, sampling height, and wind speed, model results indicated that the MFT [-35%; 95% confidence interval (CI): -22 and -49%; P < 0.001] significantly reduced drift levels compared to the AFA, but the DAT did not (-7%; 95% CI: -19 and 6%; P = 0.29). Tower sprayers appear to be a promising means by which to decrease drift levels through shorter nozzle-to-tree canopy distances and more horizontally directed aerosols that escape the tree canopy to a lesser extent. Substitution of these new technologies for AFA sprayers is likely to reduce the frequency and magnitude of pesticide drift exposures and associated illnesses. These findings, especially for the MFT, may fit United States Environmental Protection Agency's Drift Reduction Technology (DRT) one-star rating of 25-50% reduction. An 'AFA buyback' incentive program could be developed to stimulate wider adoption of new drift-reducing spray technologies. However, improved sprayer technologies alone do not eliminate drift. Applicator training, including proper sprayer calibration and maintenance, and application exclusion zones (AEZs) can also contribute to minimizing the risks of drift exposure. With regard to testing DRTs and establishing AEZs, our study findings demonstrate the need to define the impact of airblast sprayer type, orchard architecture, sampling height, and wind speed., (© The Author(s) 2019. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.)

In Washington State, half of all pesticide-related illnesses in agriculture result from drift, the off-target movement of pesticides. Of these, a significant proportion involve workers on another farm and orchard airblast applications. We compared the spray drift exposure reduction potential of two modern tower sprayers - directed air tower (DAT) and multi-headed fan tower (MFT), in relation to a traditional axial fan airblast (AFA) sprayer. We employed real-time particle monitors (Dylos DC1100) during a randomized control trial of orchard spray applications. Sections of a field were randomly sprayed by three alternating spray technologies - AFA, DAT and MFT - while monitors sampled particulate matter above and below the canopy at various downwind locations in a neighboring field. Geometric mean particle mass concentrations (PMC) outside the intended spray area were elevated during all applications at all of our sampling distances (16-74 m, 51-244 ft). After adjusting for wind speed and sampling height, the 75th percentile (95% confidence interval) PMC level was significantly greater during spray events than background levels by 105 (93, 120) μg/m 3 , 49 (45, 54) μg/m 3 and 26 (22, 31) μg/m 3 during AFA, DAT and MFT applications, respectively. Adjusted PMC levels were significantly different between all three sprayers. In this study, tower sprayers significantly reduced spray drift exposures in a neighboring orchard field when compared to the AFA sprayer, with the MFT sprayer producing the least drift; however these tower sprayers did do not fully eliminate drift., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

In Washington State, a majority of reported pesticide-related illnesses and application-related complaints involve drift. We employed real-time particle monitors (Dylos) during a series of experimental spray events investigating drift. Sections of an orchard block were randomly sprayed by an axial fan airblast sprayer, while monitors sampled particulate matter above and below the canopy at various downwind locations. We found elevated particle mass concentrations (PMC) at all distances (16-74 m). The 75th percentile PMC while spraying was significantly greater than the control periods by 107 (95% CI 94-121) μg/m 3 , after adjusting for sampler height and wind speed. The 75th percentile PMC below the canopy was significantly greater than above the canopy by 9.4 (95% CI 5.2-12) μg/m 3 , after adjusting for spraying and wind speed. In a restricted analysis of the spray events, the 75th percentile PMC significantly decreased by 2.6 (95% CI -3.2 to -1.7) μg/m 3 for every additional meter away from the edge of the spray quadrant, after adjusting for canopy height and wind speed. Our results were consistent with a larger study that performed passive sampling during the same spray events, suggesting that real-time monitoring can be used as a screening tool for pesticide drift. Compared with traditional methods of drift sampling, real-time monitoring is overall an easily employed, affordable sampling technique, and it can provide minute-by-minute measurements that can be coupled with meteorological measurements to better understand how changes in wind speed and direction affect drift.

Pesticide spray drift represents an important cause of crop damage and farmworker illness, especially among orchard workers. We drew upon exposure characteristics from known human illness cases to design a series of six spray trials that measured drift from a conventional axial fan airblast sprayer operating in a modern orchard work environment. Polyester line drift samples (n = 270; 45 per trial) were suspended on 15 vertical masts downwind of foliar applications of zinc, molybdenum, and copper micronutrient tracers. Samples were analyzed using inductively coupled plasma mass spectrometry and resulting masses were normalized by sprayer tank mix concentration to create tracer-based drift volume levels. Mixed-effects modeling described these levels in the context of spatial variability and buffers designed to protect workers from drift exposure. Field-based measurements showed evidence of drift up to 52 m downwind, which is approximately 1.7 times greater than the 30 m (100 ft) 'Application Exclusion Zone' defined for airblast sprayers by the United States Environmental Protection Agency Worker Protection Standard. When stratified by near (5 m), mid (26 m), and far (52 m) distances, geometric means and standard deviations for drift levels were 257 (1.8), 52 (2.0), and 20 (2.3) µl, respectively. Fixed effect model coefficients showed that higher wind speed [0.53; 95% confidence interval (CI): 0.35, 0.70] and sampling height (0.16; 95% CI: 0.11, 0.20) were positively associated with drift; increasing downwind distance (-0.05; 95% CI: -0.06, -0.04) was negatively associated with drift. Random effects showed large within-location variability, but relatively few systematic changes for individual locations across spray trials after accounting for wind speed, height, and distance. Our study findings demonstrate that buffers may offer drift exposure protection to orchard workers from airblast spraying. Variables such as orchard architecture, sampling height, and wind speed should be included in the evaluation and mitigation of risks from drift exposure. Data from our study may prove useful for estimating potential exposure and validating orchard-based bystander exposure models.

Implementation of probabilistic analyses in exposure assessment can provide valuable insight into the risks of those at the extremes of population distributions, including more vulnerable or sensitive subgroups. Incorporation of these analyses into current regulatory methods for occupational pesticide exposure is enabled by the exposure data sets and associated data currently used in the risk assessment approach of the Environmental Protection Agency (EPA). Monte Carlo simulations were performed on exposure measurements from the Agricultural Handler Exposure Database and the Pesticide Handler Exposure Database along with data from the Exposure Factors Handbook and other sources to calculate exposure rates for three different neurotoxic compounds (azinphos methyl, acetamiprid, emamectin benzoate) across four pesticide-handling scenarios. Probabilistic estimates of doses were compared with the no observable effect levels used in the EPA occupational risk assessments. Some percentage of workers were predicted to exceed the level of concern for all three compounds: 54% for azinphos methyl, 5% for acetamiprid, and 20% for emamectin benzoate. This finding has implications for pesticide risk assessment and offers an alternative procedure that may be more protective of those at the extremes of exposure than the current approach., (© 2017 Society for Risk Analysis.)

Mobile monitoring and fixed-site monitoring using passive sampling devices (PSD) are popular air pollutant measurement techniques with complementary strengths and weaknesses. This study investigates the utility of combining data from concurrent 2-week mobile monitoring and fixed-site PSD campaigns in Los Angeles in the summer and early spring to identify sources of traffic-related air pollutants (TRAP) and their spatial distributions. There were strong to moderate correlations between mobile and fixed-site PSD measurements of both NO 2 and NO x in the summer and spring (Pearson's r between 0.43 and 0.79), suggesting that the two data sets can be reliably combined for source apportionment. PCA identified the major TRAP sources as light-duty vehicle emissions, diesel exhaust, crankcase vent emissions, and an independent source of combustion-derived ultrafine particle emissions. The component scores of those four sources at each site were significantly correlated across the two seasons (Pearson's r between 0.58 and 0.79). Spatial maps of absolute principal component scores showed all sources to be most prominent near major roadways and the central business district and the ultrafine particle source being, in addition, more prominent near the airport. Mobile monitoring combined with fixed-site PSD sampling can provide high spatial resolution estimates of TRAP and can reveal underlying sources of exposure variability.

This research analyzed the relationship between extreme heat and Emergency Medical Service (EMS) calls in King County, WA, USA between 2007 and 2012, including the effect of community-level characteristics. Extreme heat thresholds for the Basic Life Support (BLS) data and the Advanced Life Support (ALS) data were found using a piecewise generalized linear model with Akaike Information Criterion (AIC). The association between heat exposure and EMS call rates was investigated using a generalized estimating equations with Poisson mean model, while adjusting for community-level indicators of poverty, impervious surface, and elderly population (65+). In addition, we examined the effect modifications of these community-level factors. Extreme-heat thresholds of 31.1 °C and 33.5 °C humidex were determined for the BLS and ALS data, respectively. After adjusting for other variables in the model, increased BLS call volume was significantly associated with occurring on a heat day (relative rate (RR) = 1.080, p < 0.001), as well as in locations with higher percent poverty (RR = 1.066, p < 0.001). No significant effect modification was identified for the BLS data on a heat day. Controlling for other variables, higher ALS call volume was found to be significantly associated with a heat day (RR = 1.067, p < 0.001), as well as in locations with higher percent impervious surface (RR = 1.015, p = 0.039), higher percent of the population 65 years or older (RR = 1.057, p = 0.005), and higher percent poverty (RR = 1.041, p = 0.016). Furthermore, percent poverty and impervious surface were found to significantly modify the relative rate of ALS call volumes between a heat day and non-heat day. We conclude that EMS call volume increases significantly on a heat day compared to non-heat day for both call types. While this study shows that there is some effect modification between the community-level variables and call volume on a heat day, further research is necessary. Our findings also suggest that with adequate power, spatially refined analyses may not be necessary to accurately estimate the extreme-heat effect on health., Competing Interests: The authors declare no conflict of interest.

Objective: We evaluated the effects of ozone on respiratory-related hospital admissions in three counties in Washington State from 1990 to 2006. We further examined vulnerability to ozone by key demographic factors., Method: Using linked hospital admission and ambient monitoring data, we estimated the age-, sex-, and health insurance-stratified associations between ozone (0 to 3 days' lag) and respiratory-related hospital admissions in King, Spokane, and Clark County, Washington., Results: The adjusted relative risk (RR) for a 10 ppb increase in ozone at 3 days' lag was 1.04 (95% confidence interval [CI]: 1.02, 1.07) for Clark County, 1.03 (95% CI: 1.01, 1.05) for Spokane County, and 1.02 (95% CI: 1.01, 1.03) for King County. There was consistent evidence of effect modification by age., Conclusion: Ozone at levels below federal standards contributes to respiratory morbidity among high-risk groups in Washington.

Air pollution exposure prediction models can make use of many types of air monitoring data. Fixed location passive samples typically measure concentrations averaged over several days to weeks. Mobile monitoring data can generate near continuous concentration measurements. It is not known whether mobile monitoring data are suitable for generating well-performing exposure prediction models or how they compare with other types of monitoring data in generating exposure models. Measurements from fixed site passive samplers and mobile monitoring platform were made over a 2-week period in Baltimore in the summer and winter months in 2012. Performance of exposure prediction models for long-term nitrogen oxides (NO X ) and ozone (O 3 ) concentrations were compared using a state-of-the-art approach for model development based on land use regression (LUR) and geostatistical smoothing. Model performance was evaluated using leave-one-out cross-validation (LOOCV). Models performed well using the mobile peak traffic monitoring data for both NO X and O 3 , with LOOCV R 2 s of 0.70 and 0.71, respectively, in the summer, and 0.90 and 0.58, respectively, in the winter. Models using 2-week passive samples for NO X had LOOCV R 2 s of 0.60 and 0.65 in the summer and winter months, respectively. The passive badge sampling data were not adequate for developing models for O 3 . Mobile air monitoring data can be used to successfully build well-performing LUR exposure prediction models for NO X and O 3 and are a better source of data for these models than 2-week passive badge data.

Background: Recent studies have highlighted the increased potency of oxygen analogs of organophosphorus pesticides. These pesticides and oxygen analogs have previously been identified in the atmosphere following spray applications in the states of California and Washington., Objectives: We used two passive sampling methods to measure levels of the ollowing organophosphorus pesticides: chlorpyrifos, azinphos-methyl, and their oxygen analogs at 14 farmworker and 9 non-farmworker households in an agricultural region of central Washington State in 2011., Methods: The passive methods included polyurethane foam passive air samplers deployed outdoors and indoors and polypropylene deposition plates deployed indoors. We collected cumulative monthly samples during the pesticide application seasons and during the winter season as a control., Results: Monthly outdoor air concentrations ranged from 9.2 to 199 ng/m 3 for chlorpyrifos, 0.03 to 20 ng/m 3 for chlorpyrifos-oxon, < LOD (limit of detection) to 7.3 ng/m 3 for azinphos-methyl, and < LOD to 0.8 ng/m 3 for azinphos-methyl-oxon. Samples from proximal households (≤ 250 m) had significantly higher outdoor air concentrations of chlorpyrifos, chlorpyrifos-oxon, and azinphos-methyl than did samples from nonproximal households ( p ≤ 0.02). Overall, indoor air concentrations were lower than outdoors. For example, all outdoor air samples for chlorpyrifos and 97% of samples for azinphos-methyl were > LOD. Indoors, only 78% of air samples for chlorpyrifos and 35% of samples for azinphos-methyl were > LOD. Samples from farmworker households had higher indoor air concentrations of both pesticides than did samples from non-farmworker households. Mean indoor and outdoor air concentration ratios for chlorpyrifos and azinphos-methyl were 0.17 and 0.44, respectively., Conclusions: We identified higher levels in air and on surfaces at both proximal and farmworker households. Our findings further confirm the presence of pesticides and their oxygen analogs in air and highlight their potential for infiltration of indoor living environments. Citation: Gibbs JL, Yost MG, Negrete M, Fenske RA. 2017. Passive sampling for indoor and outdoor exposures to chlorpyrifos, azinphos-methyl, and oxygen analogs in a rural agricultural community. Environ Health Perspect 125:333-341; http://dx.doi.org/10.1289/EHP425.

Diesel exhaust presents a community exposure hazard, but methods to measure internal exposure are lacking. We report results from a community-based study using 1-nitropyrene (1-NP) and its urinary metabolites as markers of exposure to traffic-related diesel particulate matter (DPM). The study participants were Tijuana, Mexico residents who commuted on foot into San Diego, California for work or school using the International San Ysidro Port of Entry, placing them within feet of idling traffic (referred to as border commuters). The comparison group (non-border commuters) was comprised of residents of south San Diego who did not commute into Mexico. Air concentration of 1-NP in fine particulate matter (PM 2.5 ) was measured in personal samples from participants. Spot urine samples were analyzed for 1-NP urinary metabolites 8-hydroxy-1-nitropyrene (8-OHNP) and 8-hydroxy-N-acetyl-1-aminopyrene (8-OHNAAP). Compared with non-border commuters, border commuters had two- to threefold higher mean urinary concentrations for unadjusted and creatinine-adjusted 8-OHNP and 8-OHNAAP. Urinary 8-OHNAAP and the sum of 8-OHNP and 8-OHNAAP were both associated with personal exposure to 1-NP in the prior 24 h. These results suggest that 1-NP urinary metabolites reflect recent exposure to DPM-derived 1-NP in community settings and can be useful for exposure analysis.

Ultrafine particle number (UFPN) and size distributions, black carbon, and nitrogen dioxide concentrations were measured downwind of two of the busiest airports in the world, Los Angeles International Airport (LAX) and Hartsfield-Jackson International Airport (ATL - Atlanta, GA) using a mobile monitoring platform. Transects were located between 5 km and 10 km from the ATL and LAX airports. In addition, measurements were taken at 43 additional urban neighborhood locations in each city and on freeways. We found a 3-5 fold increase in UFPN concentrations in transects under the landing approach path to both airports relative to surrounding urban areas with similar ground traffic characteristics. The latter UFPN concentrations measured were distinct in size distributional properties from both freeways and across urban neighborhoods, clearly indicating different sources. Elevated concentrations of Black Carbon (BC) and NO 2 were also observed on airport transects, and the corresponding pattern of elevated BC was consistent with the observed excess UFPN concentrations relative to other urban locations.

Mobile monitoring has provided a means for broad spatial measurements of air pollutants that are otherwise impractical to measure with multiple fixed site sampling strategies. However, the larger the mobile monitoring route the less temporally dense measurements become, which may limit the usefulness of short-term mobile monitoring for applications that require long-term averages. To investigate the stationarity of short-term mobile monitoring measurements, we calculated long term medians derived from a mobile monitoring campaign that also employed 2-week integrated passive sampler detectors (PSD) for NO x , Ozone, and nine volatile organic compounds at 43 intersections distributed across the entire city of Baltimore, MD. This is one of the largest mobile monitoring campaigns in terms of spatial extent undertaken at this time. The mobile platform made repeat measurements every third day at each intersection for 6-10 minutes at a resolution of 10 s. In two-week periods in both summer and winter seasons, each site was visited 3-4 times, and a temporal adjustment was applied to each dataset. We present the correlations between eight species measured using mobile monitoring and the 2-week PSD data and observe correlations between mobile NO x measurements and PSD NO x measurements in both summer and winter (Pearson's r = 0.84 and 0.48, respectively). The summer season exhibited the strongest correlations between multiple pollutants, whereas the winter had comparatively few statistically significant correlations. In the summer CO was correlated with PSD pentanes (r = 0.81), and PSD NO x was correlated with mobile measurements of black carbon (r = 0.83), two ultrafine particle count measures (r =0.8), and intermodal (1-3 μm) particle counts (r = 0.73). Principal Component Analysis of the combined PSD and mobile monitoring data revealed multipollutant features consistent with light duty vehicle traffic, diesel exhaust and crankcase blow by. These features were more consistent with published source profiles traffic-related air pollutants than features based on the PSD data alone. Short-term mobile monitoring shows promise for capturing long-term spatial patterns of traffic-related air pollution, and is complementary to PSD sampling strategies.

Background: Exposure to excessive heat kills more people than any other weather-related phenomenon, aggravates chronic diseases, and causes direct heat illness. Strong associations between extreme heat and health have been identified through increased mortality and hospitalizations and there is growing evidence demonstrating increased emergency department visits and demand for emergency medical services (EMS). The purpose of this study is to build on an existing regional assessment of mortality and hospitalizations by analyzing EMS demand associated with extreme heat, using calls as a health metric, in King County, Washington (WA), for a 6-year period., Methods: Relative-risk and time series analyses were used to characterize the association between heat and EMS calls for May 1 through September 30 of each year for 2007-2012. Two EMS categories, basic life support (BLS) and advanced life support (ALS), were analyzed for the effects of heat on health outcomes and transportation volume, stratified by age. Extreme heat was model-derived as the 95th (29.7 °C) and 99th (36.7 °C) percentile of average county-wide maximum daily humidex for BLS and ALS calls respectively., Results: Relative-risk analyses revealed an 8 % (95 % CI: 6-9 %) increase in BLS calls, and a 14 % (95 % CI: 9-20 %) increase in ALS calls, on a heat day (29.7 and 36.7 °C humidex, respectively) versus a non-heat day for all ages, all causes. Time series analyses found a 6.6 % increase in BLS calls, and a 3.8 % increase in ALS calls, per unit-humidex increase above the optimum threshold, 40.7 and 39.7 °C humidex respectively. Increases in "no" and "any" transportation were found in both relative risk and time series analyses. Analysis by age category identified significant results for all age groups, with the 15-44 and 45-64 year old age groups showing some of the highest and most frequent increases across health conditions. Multiple specific health conditions were associated with increased risk of an EMS call including abdominal/genito-urinary, alcohol/drug, anaphylaxis/allergy, cardiovascular, metabolic/endocrine, diabetes, neurological, heat illness and dehydration, and psychological conditions., Conclusions: Extreme heat increases the risk of EMS calls in King County, WA, with effects demonstrated in relatively younger populations and more health conditions than those identified in previous analyses.

Extreme heat has been associated with increased mortality, particularly in temperate climates. Few epidemiologic studies have considered the Pacific Northwest region in their analyses. This study quantified the historical (May to September, 1980-2010) heat-mortality relationship in the most populous Pacific Northwest County, King County, Washington. A relative risk (RR) analysis was used to explore the relationship between heat and all-cause mortality on 99th percentile heat days, while a time series analysis, using a piece-wise linear model fit, was used to estimate the effect of heat intensity on mortality, adjusted for temporal trends. For all ages, all causes, we found a 10% (1.10 (95% confidence interval (CI), 1.06, 1.14)) increase in the risk of death on a heat day versus non-heat day. When considering the intensity effect of heat on all-cause mortality, we found a 1.69% (95% CI, 0.69, 2.70) increase in the risk of death per unit of humidex above 36.0°C. Mortality stratified by cause and age produced statistically significant results using both types of analyses for: all-cause, non-traumatic, circulatory, cardiovascular, cerebrovascular, and diabetes causes of death. All-cause mortality was statistically significantly modified by the type of synoptic weather type. These results demonstrate that heat, expressed as humidex, is associated with increased mortality on heat days, and that risk increases with heat's intensity. While age was the only individual-level characteristic found to modify mortality risks, statistically significant increases in diabetes-related mortality for the 45-64 age group suggests that underlying health status may contribute to these risks.

Objective: Finely resolved PM2.5 exposure measurements at the level of individual participants or over a targeted geographic area can be challenging due to the cost, size and weight of the monitoring equipment. We propose re-purposing the low-cost, portable and lightweight Shinyei PPD42NS particle counter as a particle counting device. Previous field deployment of this sensor suggests that it captures trends in ambient PM2.5 concentrations, but important characteristics of the sensor response have yet to be determined. Laboratory testing was undertaken in order to characterize performance., Methods: The Shinyei sensors, in-line with a TSI Aerosol Particle Sizer (APS) model 3321, tracked particle decay within an aerosol exposure chamber. Test atmospheres were composed of monodisperse polystyrene spheres with diameters of 0.75, 1, 2 3 and 6 um as well as a polydisperse atmosphere of ASHRAE test dust #1., Results: Two-minute block averages of the sensor response provide a measurement with low random error, within sensor, for particles in the 0.75-6μm range with a limit of detection of 1 μg/m3. The response slope of the sensors is idiomatic, and each sensor requires a unique response curve. A linear model captures the sensor response for concentrations below 50 μg/m3 and for concentrations above 50 μg/m3 a non-linear function captures the response and saturates at 800 μg/m3. The Limit of Detection (LOD) is 1 μg/m3. The response time is on the order of minutes, making it appropriate for tracking short-term changes in concentration., Conclusions: When paired with prior evaluation, these sensors are appropriate for use as ambient particle counters for low and medium concentrations of respirable particles (< 100 ug/m3). Multiple sensors deployed over a spatial grid would provide valuable spatio-temporal variability in PM2.5 and could be used to validate exposure models. When paired with GPS tracking, these devices have the potential to provide time and space resolved exposure measurements for a large number of participants, thus increasing the power of a study.

Objectives: Determine protection effectiveness of 5-mil natural rubber latex (0.13-mm), 5-mil nitrile rubber (0.13-mm), and 13-mil butyl rubber (0.33-mm) glove materials against solvents present in a commonly used automotive clear coat formulation using a novel permeation panel. The latex and nitrile gloves were the type commonly used by local autobody spray painters., Methods: Glove materials were tested by spraying an automotive clear coat onto an automated reciprocating permeation panel (permeation panel II). Temperature, relative humidity, and spray conditions were controlled to optimize clear coat loading homogeneity as evaluated by gravimetric analysis. Solvent permeation was measured using charcoal cloth analyzed by the National Institute for Occupational Safety and Health 1501 method., Results: Natural rubber latex allowed 3-5 times the permeation of solvents relative to nitrile rubber for all 10 solvents evaluated: ethyl benzene, 2-heptanone, 1-methoxy-2-propyl acetate, o-xylene, m-xylene, p-xylene, n-butyl acetate, methyl isobutyl ketone, petroleum distillates, and toluene. There is a distinct behavior in solvent permeation before and after the coating dry time. Solvent permeation increased steadily before coating dry time and remained fairly constant after coating dry time. Butyl was not permeated by any of the solvents under the conditions tested., Conclusions: Commonly used 5-mil thick (0.13-mm) latex and nitrile gloves were ineffective barriers to solvents found in a commonly used clear coat formulation. Conversely, 13-mil (0.33-mm) butyl gloves were found to be protective against all solvents in the clear coat formulation., (© The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.)

Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

Shipbuilding involves intensive welding activities within enclosed and confined spaces, and although ventilation is commonly used in the industry, its use and effectiveness has not been adequately documented. Workers engaged in welding in enclosed or confined spaces in two shipyards were observed for their use of ventilation and monitored for their exposure to particulate matter. The type of ventilation in use, its placement and face velocity, the movement of air within the space, and other ventilation-related parameters were recorded, along with task characteristics such as the type of welding, the welder's position, and the configuration of the space. Mechanical ventilation was present in about two-thirds of the 65 welding scenarios observed, with exhaust ventilation used predominantly in one shipyard and supply blowers predominantly in the other. Welders were observed working in apparent dead-spaces within the room in 53% of the cases, even where ventilation was in use. Respiratory protection was common in the two shipyards, observed in use in 77 and 100% of the cases. Welding method, the proximity of the welder's head to the fume, and air mixing were found to be significantly associated with the welder's exposure, while other characteristics of dilution ventilation did not produce appreciable differences in exposure level. These parameters associated with exposure reduction can be assessed subjectively and are thus good candidates for training on effective ventilation use during hot work in confined spaces. Ventilation used in confined space welding is often inadequate for controlling exposure to welding fume., (© The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.)

Increased morbidity and mortality have been associated with extreme heat events, particularly in temperate climates. Few epidemiologic studies have considered the impact of extreme heat events on hospitalization rates in the Pacific Northwest region. This study quantifies the historic (May to September 1990-2010) heat-morbidity relationship in the most populous Pacific Northwest County, King County, Washington. A relative risk (RR) analysis was used to explore the association between heat and all non-traumatic hospitalizations on 99th percentile heat days, whereas a time series analysis using a piecewise linear model approximation was used to estimate the effect of heat intensity on hospitalizations, adjusted for temporal trends and day of the week. A non-statistically significant 2% [95% CI: 1.02 (0.98, 1.05)] increase in hospitalization risk, on a heat day vs. a non-heat day, was noted for all-ages and all non-traumatic causes. When considering the effect of heat intensity on admissions, we found a statistically significant 1.59% (95% CI: 0.9%, 2.29%) increase in admissions per degree increase in humidex above 37.4°C. Admissions stratified by cause and age produced statistically significant results with both relative risk and time series analyses for nephritis and nephrotic syndromes, acute renal failure, and natural heat exposure hospitalizations. This study demonstrates that heat, expressed as humidex, is associated with increased hospital admissions. When stratified by age and cause of admission, the non-elderly age groups (<85 years) experience significant risk for nephritis and nephrotic syndromes, acute renal failure, natural heat exposure, chronic obstructive pulmonary disease, and asthma hospitalizations.

A mobile monitoring platform developed at the University of Washington Center for Clean Air Research (CCAR) measured 10 pollutant metrics (10 s measurements at an average speed of 22 km/hr) in two neighborhoods bordering a major interstate in Albuquerque, NM, USA from April 18-24 2012. 5 days of data sharing a common downwind orientation with respect to the roadway were analyzed. The aggregate results show a three-fold increase in black carbon (BC) concentrations within 10 meters of the edge of roadway, in addition to elevated nanoparticle concentration and particulate matter with aerodynamic diameter < 1 μm (PN 1 ) concentrations. A 30% reduction in ozone concentration near the roadway was observed, anti-correlated with an increase in the oxides of nitrogen (NO x ). In this study, the pollutants measured have been expanded to include polycyclic aromatic hydrocarbons (PAH), particle size distribution (0.25-32 μm), and ultra-violet absorbing particulate matter (UVPM). The raster sampling scheme combined with spatial and temporal measurement alignment provide a measure of variability in the near roadway concentrations, and allow us to use a principal component analysis to identify multi-pollutant features and analyze their roadway influences.

The objective of this study was to use membrane introduction mass spectrometry (MIMS), implemented on a mobile platform, in order to provide real-time, fine-scale, temporally and spatially resolved measurements of several hazardous air pollutants. This work is important because there is now substantial evidence that fine-scale spatial and temporal variations of air pollutant concentrations are important determinants of exposure to air pollution and adverse health outcomes. The study took place in Tacoma, WA during periods of impaired air quality in the winter and summer of 2008 and 2009. Levels of fine particles were higher in winter compared to summer, and were spatially uniform across the study area. Concentrations of vapor phase pollutants measured by membrane introduction mass spectrometry (MIMS), notably benzene and toluene, had relatively uniform spatial distributions at night, but exhibited substantial spatial variation during the day-daytime levels were up to 3-fold higher at traffic-impacted locations compared to a reference site. Although no direct side-by-side comparison was made between the MIMS system and traditional fixed site monitors, the MIMS system typically reported higher concentrations of specific VOCs, particularly benzene, ethylbenzene and naphthalene, compared to annual average concentrations obtained from SUMA canisters and gas chromatographic analysis at the fixed sites.

Organophosphorus pesticides are some of the most widely used insecticides in the US, and spray drift may result in human exposures. We investigate sampling methodologies using the polyurethane foam passive air sampling device to measure cumulative monthly airborne concentrations of OP pesticides chlorpyrifos, azinphos-methyl, and oxygen analogs. Passive sampling rates (m(3)d(-1)) were determined using calculations using chemical properties, loss of depuration compounds, and calibration with side-by-side active air sampling in a dynamic laboratory exposure chamber and in the field. The effects of temperature, relative humidity, and wind velocity on outdoor sampling rates were examined at 23 sites in Yakima Valley, Washington. Indoor sampling rates were significantly lower than outdoors. Outdoor rates significantly increased with average wind velocity, with high rates (>4m(3)d(-1)) observed above 8ms(-1). In exposure chamber studies, very little oxygen analog was observed on the PUF-PAS, yet substantial amounts chlorpyrifos-oxon and azinphos methyl oxon were measured in outdoor samples. PUF-PAS is a practical and useful alternative to AAS because it results in little artificial transformation to the oxygen analog during sampling, it provides cumulative exposure estimates, and the measured sampling rates were comparable to rates for other SVOCs. It is ideal for community based participatory research due to low subject burden and simple deployment in remote areas., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Context: Studies of burnout among allopathic physicians have shown many deleterious effects for both physicians and patients. To our knowledge, no studies have quantified burnout among osteopathic physicians., Objective: To determine the prevalence of burnout, mentoring, and resident training satisfaction among US osteopathic otolaryngology residents compared with previously published data for allopathic otolaryngology residents., Methods: A cross-sectional, questionnaire-based, electronic survey of US osteopathic otolaryngology residents was conducted. Residents were surveyed about demographic information, personal and professional life satisfaction, professional stressors, burnout (assessed with the Maslach Burnout Inventory-Human Services Survey), and mentor-resident interactions. Burnout was measured based on levels of emotional exhaustion (EE), depersonalization (DP), and low personal accomplishment (PA). Results were compared with previously published data for allopathic otolaryngology residents., Results: Of the 102 osteopathic residents contacted, 48 (47%) responded and 47 provided complete responses in some categories. Burnout rates were low in 11 respondents (23%), moderate in 31 (66%), and high in 5 (11%), compared with published rates of 14%, 76%, and 10%, respectively, for allopathic residents (P=.18). The rates of EE and DP did not differ significantly from published data, but levels of PA were higher in osteopathic residents (P=.03). Sleep hours per night were significantly higher in osteopathic than in allopathic residents (mean, 6.6 vs 6.2; P=.04), and work hours per week were significantly lower (mean, 62 vs 71; P<.001). Increased EE scores were negatively associated with hours of sleep (ρ=-0.42, P=.003). Increased influence from a mentor was associated with decreased levels of burnout for all 3 components (EE: ρ=-0.54, P=.002; DP: ρ=-0.59, P<.001; PA: ρ=0.44, P=.02)., Conclusion: To our knowledge, the current study is the first to quantify burnout among osteopathic residents, and our findings suggest that osteopathic residents have lower rates of burnout than allopathic residents. Osteopathic residents reported lower rates of low PA, increased hours of sleep, and decreased overall work hours. Further study of the relationship between mentoring and decreased burnout is needed., (© 2014 The American Osteopathic Association.)

A rapid liquid chromatography tandem mass spectrometry (LC-MS/MS) method has been developed for determination of levels of the organophosphorus (OP) pesticides chlorpyrifos (CPF), azinphos methyl (AZM), and their oxygen analogs chlorpyrifos-oxon (CPF-O) and azinphos methyl-oxon (AZM-O) on common active air sampling matrices. XAD-2 resin and polyurethane foam (PUF) matrices were extracted with acetonitrile containing stable-isotope labeled internal standards (ISTD). Analysis was accomplished in Multiple Reaction Monitoring (MRM) mode, and analytes in unknown samples were identified by retention time (±0.1 min) and qualifier ratio (±30% absolute) as compared to the mean of calibrants. For all compounds, calibration linearity correlation coefficients were ≥0.996. Limits of detection (LOD) ranged from 0.15-1.1 ng/sample for CPF, CPF-O, AZM, and AZM-O on active sampling matrices. Spiked fortification recoveries were 78-113% from XAD-2 active air sampling tubes and 71-108% from PUF active air sampling tubes. Storage stability tests also yielded recoveries ranging from 74-94% after time periods ranging from 2-10 months. The results demonstrate that LC-MS/MS is a sensitive method for determining these compounds from two different matrices at the low concentrations that can result from spray drift and long range transport in non-target areas following agricultural applications. In an inter-laboratory comparison, the limit of quantification (LOQ) for LC-MS/MS was 100 times lower than a typical gas chromatography-mass spectrometry (GC-MS) method.

Objectives: Modify a permeation panel to evaluate dermal protective clothing for resistance to sprayed coatings with minimal variability in spray paint loading across the test panel. Determine isocyanate protection effectiveness of natural rubber latex (5 mil or 0.13mm), nitrile rubber (5 mil or 0.13mm), and butyl rubber (13 mil or 0.33mm) glove materials against a commonly used automotive clear coat formulation. The latex and nitrile gloves were the type used by the local autobody spray painters., Methods: Glove materials were tested by spraying paint onto an automated reciprocating permeation panel (permeation panel II). Temperature, relative humidity, and spray conditions were controlled to optimize paint loading homogeneity as evaluated by gravimetric analysis. Isocyanate permeation was measured using 1-(2-pyridyl)-piperazine-coated fiber-glass filters analyzed by a modified version of the OSHA 42/PV2034 methods., Results: Latex exhibited a higher permeation rate compared with nitrile for isocyanates (1,6-hexamethylene diisocyanate (HDI) and isophorone diisocyanate monomers) and both materials presented permeation at all of the time points suggesting a fast isocyanate breakthrough. Butyl material exhibited no permeation or breakthrough for isocyanates under the tested conditions. The spray application at 69±8°F was optimally homogeneous at 45±0.5mg weight of dry clear coat per 5cm(2)., Conclusions: The permeation panel II is a reliable method to assess dermal protective clothing performance against polymerizing coatings. Commonly used 5-mil (0.13-mm) latex and nitrile gloves were determined to be ineffective barriers against the isocyanates found in a commonly used clear-coat formulation while butyl gloves were protective.

This research describes the design, deployment, performance, and acceptability of a novel outdoor active air sampler to provide simultaneous measurements of multiple contaminants at timed intervals for the Aggravating Factors of Asthma in Rural Environment (AFARE) study-a longitudinal cohort of 50 children in Yakima Valley, Washington. The sampler was constructed of multiple sampling media connected to individual critical orifices and a rotary vane vacuum pump. It was connected to a timed control valve system to collect 24 hours samples every six days over 18 months. We describe a spatially representative approach with both quantitative and qualitative location criteria to deploy a network of 14 devices at participant residences in a rural region (20 × 60 km). Overall the sampler performed well, as the concurrent mean sample flow rates were within or above the ranges of recommended sampling rates for each exposure metric of interest. Acceptability was high among the study population of Hispanic farmworker participant households. The sampler design may prove useful for future urban and rural community-based studies with aims at collecting multiple contaminant data during specific time periods.

Side-by-side active air sampling for the organophosphorus (OP) pesticide, chlorpyrifos (CPF) and its oxygen analog, chlorpyrifos-oxon (CPF-O) was conducted with two recommended air sampling matrices: OSHA Versatile Sampling (OVS) tubes with XAD-2 resin, polyurethane foam (PUF) tubes, and passive PUF deposition disks. The study compared the proportion of artificially transformed CPF-O in the laboratory and in the field during a tree fruit application in Washington State. Lab results demonstrated that the NIOSH-recommended OVS tubes artificially transformed up to 32% of CPF to CPF-O during the sampling process, whereas PUF tubes had little to no artificial transformation (⩽0.1%). In the field, the proportion of CPF-O in the sample was significantly higher on OVS tubes than on PUF tubes (p<0.001), confirming that OVS tubes were converting a significant portion of CPF to CPF-O. In addition, PUF tubes reported measurable levels CPF-O in the field even when no artificial transformation was expected. We conclude that the PUF matrix is the superior sampling medium for OP oxygen analogs when compared to XAD-two resin. Community-located PUF tube samples 24h post-application had considerably higher levels CPF-O (16-21ngm(-3)) than near field samples during application (2-14ngm(-3)), suggesting that the oxygen analog is volatile and formed during atmospheric transport. It is recommended that worker and community risk assessments begin to take into consideration the presence of the more toxic oxygen analogs when measuring for OP pesticide mixtures., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

Diesel exhaust (DE) is a significant contributor to the toxicity associated with particulate matter (PM). 1-Nitropyrene (1-NP) has been used as a molecular marker for DE, and the urinary metabolites of 1-NP have been proposed as biomarkers for exposure to DE. In this study, several urinary 1-NP metabolites were evaluated for their utility as markers of short-term exposures to DE. The study population was a cohort of 24 taxi drivers from Shenyang, China, who submitted urine samples collected before, after, and the next morning following their workshifts. The urinary metabolites studied were isomers of hydroxy-1-nitropyrene (3-, 6-, 8- OHNPs) and hydroxy-N-acetyl-1-aminopyrene (3-,6-, 8-OHNAAPs). Exposure to DE was estimated based on exposure to 1-NP in air samples collected during and after the driver's workshift; 6- and 8-OHNP, and 8-OHNAAP were consistently detected in the drivers' urine. Concentrations of the metabolites in the taxi drivers' urine were greater than metabolite levels previously reported in non-occupationally exposed subjects; however no associations were observed between subject-specific exposures to 1-NP and urinary metabolites measured at the end of the workshift or in the next morning void. Significant autocorrelation was observed in metabolite levels in successive urine samples, from which half-lives for urinary elimination of ~10-12 h were estimated. These observations suggest that, in an occupational setting, urinary 1-NP metabolites may be more suitable as markers of ongoing exposure (timescales of several days) rather than indicators of acute exposure associated with single workshifts.

A number of recent toxicity studies have highlighted the increased potency of oxygen analogs (oxons) of several organophosphorus (OP) pesticides. These findings were a major concern after environmental oxons were identified in environmental samples from air and surfaces following agricultural spray applications in California and Washington State. This paper reports on the validity of oxygen analog measurements in air samples for the OP pesticide, chlorpyrifos. Controlled environmental and laboratory experiments were used to examine artificial formation of chlorpyrifos-oxon using OSHA Versatile Sampling (OVS) tubes as recommended by NIOSH method 5600. Additionally, we compared expected chlorpyrifos-oxon attributable to artificial transformation to observed chlorpyrifos-oxon in field samples from a 2008 Washington State Department of Health air monitoring study using non-parametric statistical methods. The amount of artificially transformed oxon was then modeled to determine the amount of oxon present in the environment. Toxicity equivalency factors (TEFs) for chlorpyrifos-oxon were used to calculate chlorpyrifos-equivalent air concentrations. The results demonstrate that the NIOSH-recommended sampling matrix (OVS tubes with XAD-2 resin) was found to artificially transform up to 30% of chlorpyrifos to chlorpyrifos-oxon, with higher percentages at lower concentrations (< 30 ng/m3) typical of ambient or residential levels. Overall, the 2008 study data had significantly greater oxon than expected by artificial transformation, but the exact amount of environmental oxon in air remains difficult to quantify with the current sampling method. Failure to conduct laboratory analysis for chlorpyrifos-oxon may result in underestimation of total pesticide concentration when using XAD-2 resin matrices for occupational or residential sampling. Alternative methods that can accurately measure both OP pesticides and their oxygen analogs should be used for air sampling, and a toxicity equivalent factor approach should be used to determine potential health risks from exposures.

The transport of mixed paint solvents through natural rubber latex (4 mil) and nitrile rubber (5 mil) gloves was evaluated after spray application of the paint formulation directly on the glove surface. Glove materials and thicknesses were those selected by the majority of spray painters in the local automobile repair industry. A flat panel containing glove specimens mounted in multiple permeation cells permitted evaporation of solvents from the applied paint and incorporated a solid sorbent receiving medium for measuring glove membrane transport. The panel was sprayed in a paint booth to simulate use conditions. Charcoal cloth under the glove adsorbed transported solvents, which were quantified by gas chromatography. For each solvent component, results were expressed as mass transported through the glove relative to the mass applied, per unit area, during 30 min after spray application. The paint formulation contained ketones, acetates, and aromatics. Natural rubber latex allowed 6-10 times the transport of solvents relative to nitrile rubber for all eight solvent components: methyl ethyl ketone, toluene, styrene, ethyl benzene, xylene isomers, and 2-heptanone. m-Xylene showed the largest difference in transport between the two glove materials. This solvent also had the highest transport for each material. The results indicate that nitrile rubber gloves offer somewhat greater chemical resistance to all eight solvents studied compared with natural rubber latex gloves, regardless of the chemical properties of the individual solvent components. However, it must be emphasized that neither of the glove materials, in the thicknesses used in this study, provide adequate protection when exposed by direct spray painting. Simulation of realistic spray conditions may offer a source of useful information on the performance of chemical protective gloves because it accounts for solvent evaporation and the effect of paint polymerization after application on glove transport.

Substantial exposure to isocyanates may occur during spray painting in autobody shops, yet information is lacking on the efficacy of the protective clothing used during spray painting. We investigated the personal and workplace factors associated with painters' dermal protection use during a large-scale exposure assessment study. Survey data indicated that 69% of painters always used gloves, with latex gloves (47%) and nitrile gloves (34%) used most frequently. Among latex glove users, 53% used thin latex (0.05-0.13 mm), 6% used medium latex (0.15-0.20 mm), and 12% used thick latex (> 0.20 mm). Among nitrile glove users, 27% used thin nitrile and 45% used medium nitrile. Sixty-three percent of painters always used coveralls, 44% preferring one particular brand. Although overspray presents an opportunity for dermal exposure to the neck and face, only 19% of painters protected these areas with personal protective equipment. Painters who always used coveralls were more likely to use gloves (odds ratio = 7.9, p = 0.061). Painters who reported ever having smoked cigarettes used gloves (p = 0.05) and coveralls (p = 0.04) more frequently. Painters who sprayed more than 34 clear coat jobs per month used coveralls most frequently (p = 0.038). Exact logistic regressions along with random sample calculations indicated that the survey results were independent of the shops. Because of the small sample size in this study, future research is warranted to corroborate these results. Studying the effectiveness of gloves and coveralls against polyurethane paints and understanding the underlying motivators and preferences for painters and business owners is needed for the development of best practices for the selection and use of dermal protection.

Anaerobic digesters provide clean, renewable energy (biogas) by converting organic waste to methane, and are a key part of China's comprehensive rural energy plan. Here, experimental and modeling results are used to quantify the net greenhouse gas (GHG) reduction from substituting a household anaerobic digester for traditional energy sources in Sichuan, China. Tunable diode laser absorption spectroscopy and radial plume mapping were used to estimate the mass flux of fugitive methane emissions from active digesters. Using household energy budgets, the net improvement in GHG emissions associated with biogas installation was estimated using global warming commitment (GWC) as a consolidated measure of the warming effects of GHG emissions from cooking. In all scenarios biogas households had lower GWC than nonbiogas households, by as much as 54%. Even biogas households with methane leakage exhibited lower GWC than nonbiogas households, by as much as 48%. Based only on the averted GHG emissions over 10 years, the monetary value of a biogas installation was conservatively estimated at US$28.30 ($16.07 ton(-1) CO(2)-eq), which is available to partly offset construction costs. The interaction of biogas installation programs with policies supporting improved stoves, renewable harvesting of biomass, and energy interventions with substantial health cobenefits are discussed.

Objectives: Design, construct, and characterize an apparatus to evaluate dermal protective clothing for resistance to polymerizing materials. Specifically, we evaluated the permeation of the most common glove material used in automotive collision repair (0.10-0.13 mm or 4-5 mil latex) with representative isocyanate-containing clear coats. Our ultimate goal is to make informed recommendations on dermal protective materials to prevent isocyanate exposures and reduce the likelihood of occupational illness in automotive collision repair and other industries., Methods: A novel permeation panel was developed to assess dermal protective clothing. With this apparatus, up to eight test materials may be evaluated under typical-spray application conditions. Solid collection media comprised of 1-(2-pyridyl)-piperazine (2-PP)-coated fiberglass filters or colorimetric SWYPE™ pads were placed behind test materials to capture permeants. The 2-PP-coated filters were subsequently analyzed using a modified OSHA42/PV2034 method. Color change in the SWYPEs provided an immediate field estimate of breakthrough time. In addition, Teflon filters were mounted proximal to the permeation cells to measure the mass of clear coat applied to the panel and to evaluate loading homogeneity. This study evaluated the permeation of isocyanates through 0.10-0.13 mm latex glove material at a fixed time (30 min post-spraying) and over a time course (6-91 min post-spraying)., Results: Monomers 1,6-hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI) permeated through (0.10-0.13 mm) latex glove material under typical glove use conditions (30 min). The latex glove material exhibited immediate breakthrough, with a permeation rate of 2.9 ng min(-1) cm(-2). The oligomeric forms of HDI and IPDI did not permeate the latex glove material. The spray application at 71 ± 5 °F was fairly homogeneous (33.7 ± 8 mg weight of dry clear coat per 5 cm(2))., Conclusions: The permeation panel is a viable method to assess dermal protective clothing performance against polymerizing materials. Thin (0.10-0.13 mm) latex gloves were determined to be ineffective barriers to the isocyanates commonly found in clear coats. Because this type of glove is used frequently in auto body shops, the potential for isocyanate exposure is of concern. Permeation tests with other dermal protective clothing materials and other clear coat formulations are needed to make recommendations about alternative materials.

Colorimetric SWYPE pads are useful tools for identifying unpolymerized aliphatic isocyanates on a variety of surfaces. This technique has been used in autobody shops to determine the presence of hexamethylene diisocyanate and other aliphatic isocyanates that are important constituents of many automotive coatings. SWYPEs have the advantage of being relatively inexpensive, rapid, and portable. The color change elicited by aliphatic isocyanates (from yellow to red) provides a visual indication of the extent of surface contamination. To quantify isocyanate contamination based on the colorimetric response, an objective color scale was developed for isocyanate loading. Sampled pads were digitized on a calibrated, portable flatbed scanner, and red-green-blue (RGB) histograms of SWYPE images were created. A calibration curve was created from a series of reference images derived from SWYPEs loaded with an isocyanate-containing product. The SWYPE RGB analysis allowed for quantification over a range of isocyanate loadings: from approximately 0.01 to 24.0 microg/cm(2), with reproducibility of >90%, accuracy >90%, and a surface extraction efficiency of >90%. RGB analysis exhibited a lower detection limit than visual scoring (approximately 3 microg versus approximately 10 microg). The colorimetric response was cross validated with a high-performance liquid chromatography quantitative assay. When combined with RGB analysis, SWYPE colorimetric wipes represent a rapid and inexpensive method to assess objectively surface contamination with aliphatic isocyanates.

We examined the significance of meteorology and postspray volatilization of methamidophos (an organophosphorus insecticide) in assessing potential inhalation risk to children in an agricultural community. We combined fluxes from sources and dispersion modeling with a range of possible local meteorology to create output to study the variability in potential community exposure as a result of changing temperature, wind speeds and wind directions. This work is based on an aerial spray drift study where air sampling measurements of methamidophos were made before, during and after a spray event were used to examine acute inhalation risk for children living in an Eastern Washington State community in close proximity (between 15 and 200 m) to sprayed potato fields. We compared the measured average air concentrations of methamidophos in the community to a "no observed adverse effect level" for subchronic inhalation to characterize acute and subchronic inhalation risks. The baseline estimates of inhalation exposure were below Environment Protection Agency's (EPA) level of concern based on a target margin of exposure of 300. As meteorological conditions during and after spraying influence the amount of material moving into areas where children reside we used historical meteorological data to drive model simulations that predicted likely air residue concentrations under different wind and temperature conditions. We also added variability to the decay constant and initial emission fluxes to create a 2-D simulation of estimated air concentrations in the community near the fields. This work provides a methodological framework for the assessment of air concentrations of pesticides from agricultural sprays in the absence of extended measurements, although including variability from meteorological conditions. The deterministic as well as the probabilistic risk analyses in this study indicated that postspray volatilization in the specific spray situation analyzed (methamidophos applied on potato fields in Eastern Washington) did not pose acute or subchronic risks as defined by the EPA. However, this study did not consider any pathway of exposure other than inhalation (e.g. diet, dermal, etc.) and the risk assessment should be evaluated in that context.

Measures of hand and finger anthropometry are very important for designing many hand held devices as well as understanding anthropometric effects on the operation of such devices. Many historical datasets have measured and recorded gross hand dimensions but do not often record the finer dimensions of the hand such as finger anthropometry. Knowing the size and mass of fingers across genders can be critical to the design and operation of hand held devices. In this paper we compare two empirical linear models that predicts index finger width at the proximal interphalangeal (PIP) joint (a finger anthropometric measure) based on hand-width (hand anthropometric measure). This will be especially useful for deriving population measures of finger anthropometry from large historical data sets where only gross hand dimensions are available.

Purpose: This cohort study aims to examine cardiovascular disease (CVD) mortality risks among workers in occupations potentially exposed to magnetic fields (MF)., Methods: Risks for major CVD mortality by potential job-related MF exposure were examined in a sample of U.S. workers from the National Longitudinal Mortality Study using multivariate proportional hazards models., Results: After adjustment for demographic factors, there were no significant excess risks between individuals with medium (0.15 to <0.20 microT), high (0.20 to < 0.30 microT), or very high (>/= 0.30 microT) exposure levels as compared with individuals with background exposure levels of MF (<0.15 microT) for the CVD mortality outcomes. Indirect adjustment for potential confounding by current smoking prevalence did not change the pattern of these results., Conclusion: Our study does not provide evidence for an association between occupational MF exposure and CVD mortality risk.

Elevated geomagnetic activity has been linked with human psychological, neurological and cardiovascular outcomes, and altered melatonin production has been implicated as an underlying mechanism to explain these effects. The relationship between geomagnetic activity and overnight excretion of the melatonin metabolite, 6-hydroxymelatonin sulfate (6-OHMS), was evaluated in a population of 153 male electric utility workers. The effect of geomagnetic activity combined with either 60Hz magnetic field or ambient light exposures was also evaluated. Elevated equivalent amplitudes (USGS, Boulder, CO) were associated with lower adjusted mean nocturnal 6-OHMS/cr concentrations and reduced total overnight 6-OHMS excretion, consistent with a previous study. Time intervals in which geomagnetic activity predicted the largest differences in mean 6-OHMS excretion generally occurred between 15- and 33-h prior to urine sample collection. These times coincide with key periods of melatonin regulation and production, respectively, suggesting that geomagnetic activity may play a role in the entrainment of human melatonin rhythms.