Search

It is one concern of the researchers how magnesium (Mg) alloys solidify under different conditions and how their microstructure evolves during solidification, and what are the relationship between the macroscopic properties and various microstructures. Such issues are difficult to be revealed through experiments only, especially for the newly developed Mg alloys, for which there is a lack of more systematic and mature system. However, multi-scale modeling and simulation can promote and deepen our understanding of the microstructure and its deformation mechanism. In this paper, we review and summarize the recent research progress of numerical simulation of Mg alloys in forming and microstructure, namely casting, extrusion, rolling, and welding, using crystal plasticity finite element (CPFEM) and molecular dynamics (DM) methods. Besides, the methods and innovations of modeling are also summarized. Lastly, the paper discusses the development prospects and challenges of the numerical simulation in the field of Mg alloys.

In this study, the nano-TiC/AZ61 composites with different heterogeneous bimodal grain (HBG) structures and uniform structure are obtained by regulating the extrusion speed. The effect of HBG structure on the mechanical properties of the composites is investigated. The increasing ductility and toughening mechanism of HBG magnesium matrix composites are carefully discussed. When the extrusion speed increases from 0.75 mm/s to 2.5 mm/s or 3.5 mm/s, the microstructure transforms from uniform to HBG structure. Compared with Uniform-0.75 mm/s composite, Heterogeneous-3.5 mm/s composite achieves a 116.7% increase in ductility in the plastic deformation stage and almost no reduction in ultimate tensile strength. This is mainly because the lower plastic deformation inhomogeneity and higher strain hardening due to hetero-deformation induced (HDI) hardening. Moreover, Heterogeneous-3.5 mm/s composite achieves a 108.3% increase in toughness compared with the Uniform-0.75 mm/s composite. It is mainly because coarse grain (CG) bands can capture and blunt cracks, thereby increasing the energy dissipation for crack propagation and improving toughness. In addition, the CG band of the Heterogeneous-3.5 mm/s composite with larger grain size and lower dislocation density is more conducive to obtaining higher strain hardening and superior blunting crack capability. Thus, the increased ductility and toughness of the Heterogeneous-3.5 mm/s composite is more significant than that Heterogeneous-2.5 mm/s composite.

BackgroundEffective interprofessional education (IPE) can facilitate teamwork between dentists and dental technicians, thereby enabling the efficient provision of high-quality dental care. ObjectiveThis study aimed to design and assess an IPE module named Project 35, which was offered to dental and dental technology students early in their undergraduate training as a precursor to a more comprehensive IPE curriculum in dentistry and dental technology. MethodsLeveraging positive behavior support (PBS) theory, Project 35 was devised as an innovation and entrepreneurship educational training framework. It used project-based learning to cultivate teamwork skills and to promote the professional development of dental and dental technology students. The pilot study was designed to present the IPE module and preliminarily assess its validity. In survey 1, which was conducted immediately after the course, the dental and dental technology students’ self-reported skill acquisition and attitudes were assessed and compared. Survey 2, conducted 1 year after the course, focused on the comparative benefits of Project 35 training for dental technology students versus an untrained group. ResultsA total of 66 students, including 36 dental students and 30 dental technology students who had undertaken the training, were recruited. Project 35 training improved teamwork skills for students in both disciplines comparably, and the students recognized the training as highly valuable and effective. The mean values for all items indicating skills improvement of students ranged from 4.13 (SD 0.797) to 4.63 (SD 0.495) for dental students and from 4.13 (SD 0.869) to 4.74 (SD 0.619) for dental technology students. Among the dental technology students, the trained group showed greater independent and innovative approaches and was more optimistic about the future of the profession than the nontrained group (P

Abstract Diabetes mellitus affected more than 500 million of people globally, with an annual mortality of 1.5 million directly attributable to diabetic complications. Oxidative stress, in particularly in post-prandial state, plays a vital role in the pathogenesis of the diabetic complications. However, oxidative status marker is generally poorly characterized and their mechanisms of action are not well understood. In this work, we proposed a new framework for deep characterization of oxidative stress in erythrocytes (and in urine) using home-built micro-scale NMR system. The dynamic of post-prandial oxidative status (against a wide variety of nutritional load) in individual was assessed based on the proposed oxidative status of the red blood cells, with respect to the traditional risk-factors such as urinary isoprostane, reveals new insights into our understanding of diabetes. This new method can be potentially important in drafting guidelines for sub-stratification of diabetes mellitus for clinical care and management.

In order to obtain Mg alloys with fine microstructures and high mechanical performances, a novel friction-based processing method, name as “constrained friction processing (CFP)”, was investigated. Via CFP, defect-free Mg-Zn-Ca rods with greatly refined grains and high mechanical properties were produced. Compared to the previous as-cast microstructure, the grain size was reduced from more than 1 mm to around 4 µm within 3 s by a single process cycle. The compressive yield strength was increased by 350% while the ultimate compressive strength by 53%. According to the established material flow behaviors by “tracer material”, the plastic material was transported by shear deformation. From the base material to the rod, the material experienced three stages, i.e. deformation by the tool, upward flow with additional tilt, followed by upward transportation. The microstructural evolution was revealed by “stop-action” technique. The microstructural development at regions adjacent to the rod is mainly controlled by twinning, dynamic recrystallization (DRX) as well as particle stimulated nucleation, while that within the rod is related to DRX combined with grain growth.

Magnesium and its alloys have such advantages with lightweight, high specific strength, good damping, high castability and machinability, which make them an attractive choice for applications where weight reduction is important, such as in the aerospace and automotive industries. However, their practical applications are still limited because of their poor corrosion resistance, low high temperature strength and ambient formability. Based on such their property shortcomings, recently degradable magnesium alloys were developed for broadening their potential applications. Considering the degradable Mg alloys for medical applications were well reviewed, the present review put an emphasis on such degradable magnesium alloys for structural and functional applications, especially the applications in the environmental and energy fields. Their applications as fracture ball in fossil energy, sacrificial anode, washing ball, and as battery anodes, transient electronics, were summarized. The roles of alloying elements in magnesium and the design concept of such degradable magnesium alloys were discussed. The existing challenges for extending their future applications are explored.

The present work reports the creep behavior and microstructural evolution of the sand-cast Mg–14Gd–0.4Zr alloy (wt.%) prepared by the differential pressure casting machine. Their compressive creep tests at 250 °C were performed under various applied stresses (i.e., 60, 80 and 100 MPa). Among them, the sand-cast Mg–14Gd–0.4Zr samples examined under 250 °C/80 MPa for 39 and 95 h, respectively, were chosen to systemically analyze their creep mechanisms using high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM). The obtained results showed that the enhancement of creep resistance can be mainly attributed to the coherent β' and β'F phases with an alternate distribution, effectively impeding the basal dislocations movement. However, with the creep time increasing, the fine β'+β'F precipitate chains coarsened and transformed to semi-coherent β1 phase and even to large incoherent β phase (surrounded by precipitate-free areas) in grain interiors. The precipitate-free zones (PFZs) at grain boundaries (GBs) were formed, and they could expand during creep deformation. Apart from the main cross-slip of basal and prismatic dislocations, type dislocations were activated and tended to distribute near the GBs. The aforementioned phenomena induced the stress concentrations, consequently leading to the increment of the creep strain.

In order to improve the ductility of commercial WE43 alloy and reduce its cost, a Mg-3Y-2Gd-1Nd-0.4Zr alloy with a low amount of rare earths was developed and prepared by sand casting with a differential pressure casting system. Its microstructure, mechanical properties and fracture behaviors in the as-cast, solution-treated and as-aged states were evaluated. It is found that the aged alloy exhibited excellent comprehensive mechanical properties owing to the fine dense plate-shaped β' precipitates formed on prismatic habits during aging at 200 °C for 192 hrs after solution-treated at 500 °C for 24 hrs. Its ultimate tensile strength, yield strength, and elongation at ambient temperature reach to 319 ± 10 MPa, 202 ± 2 MPa and 8.7 ± 0.3% as well as 230 ± 4 MPa, 155 ± 1 MPa and 16.0 ± 0.5% at 250 °C. The fracture mode of as-aged alloy was transferred from cleavage at room temperature to quasi-cleavage and ductile fracture at the test temperature 300 °C. The properties of large-scale components fabricated using the developed Mg-3Y-2Gd-1Nd-0.4Zr alloy are better than those of commercial WE43 alloy, suggesting that the new developed alloy is a good candidate to fabricate the large complex thin-walled components.

In this study, the texture evolutions of two Mg materials during tension are explored. In-situ X-ray synchrotron and Visco-Plastic Self-Consistent (VPSC) modeling are employed to investigate the different deformation modes between pure Mg and Mg–15Gd (wt.%) alloy. These two materials with a strong extrusion texture show large different slip/twinning activity behaviors during tensile deformation. The basal 〈a〉 slip has the highest contribution to the initial stage of plastic deformation for pure Mg. During the subsequent plastic deformation, the prismatic slip is dominant due to the strong ED // 〈100〉 fiber texture. In contrast, the deformation behavior of Mg–15Gd alloy is more complex. Twinning and basal slip are dominant at the early stage of plastic deformation, but further deformation results in the increased activation of prismatic and pyramidal slips. In comparison to pure Mg, the ratios of the critical resolved shear stress (CRSS) between non-basal slip and basal slip of the Mg–15Gd alloy are much lower.

Microstructural evolution and strengthening mechanisms of Mg-3Sn-1Ca based alloys with additions of different amounts of AlN nano-particles were investigated. It was found that with increasing the amount of AlN nano-particles the grain size decreases obviously. The existence of AlN nano-particles could refine the primary crystal phases CaMgSn, which provided more heterogeneous nucleation sites for the formation of magnesium. Moreover, such nano-particles could also restrict the grain growth during solidification. After adding AlN nano-particles, both the tensile properties at room temperature and high temperature 250 °C and the hardness are largely improved. The improvement of strength is attributed to grain refinement and second phase refinement.

With the increasing demand for innovative therapies, biodegradable magnesium has attracted more and more attention, which could avoid secondary surgery and reduce complications. Until now, plenty of researchers take part in the research & development of this field, and many articles have been published every year. However, it is a huge challenge to predict research trends and definite topics for researchers, which could result in low research value, wasted resources and even slowed medical device transformation. Usually, reviews summarize a specific topic, such as alloy elements, coating designs, degradable properties, etc. Deriving key indicators from a large amount of data with the help of statistical analysis, make a historical review, current situation analysis, and future prediction more convincing. Herein, it has been conducted a bibliometric study according to 2669 publications collected from the Web of Science (WOS) database from 2005 to 2021. By analyzing some key factors, including annual publications, keywords, country contributions, authors as well as institutions, the evolution of biodegradable magnesium is objectively studied. The research trends of biodegradable magnesium alloys are corrosion resistance, the influence of microstructural control on mechanical behavior and bio-functions of implants in a chronological manner. The co-occurrence mapping of the countries and authors suggests that current in-depth research and development of magnesium is more emphasis on institutional and international cooperation.

To have a better understand on the change of microstructure via kinetics, the diffusion behavior of Mg alloys is of special interest to researchers. Meanwhile, diffusion coefficients of Mg based alloys can explain and represent their diffusion behavior well. The evolution of experimental and calculated methods for detecting and extracting diffusion coefficients was discussed briefly. The reasonable diffusion data, especially self-diffusion coefficients, impurity diffusion coefficients and inter-diffusion coefficients of Mg alloys, were reviewed in detail serving to design the Mg alloys with higher accuracy. Then the practical applications of diffusion coefficients of Mg alloys were summarized, including diffusional mobility establishing, precipitation simulation and mechanical properties prediction.

Abstract Objective Additively manufactured (3D-printed) titanium meshes have been adopted in the dental field as non-resorbable membranes for guided bone regeneration (GBR) surgery. However, according to previous studies, inaccuracies between planned and created bone volume and contour are common, and many reasons have been speculated to affect its accuracy. The size of the alveolar bone defect can significantly increase patient-specific titanium mesh design and surgical difficulty. Therefore, this study aimed to analyze and investigate the effect of bone defect size on the 3D accuracy of alveolar bone augmentation performed with additively manufactured patient-specific titanium meshes. Methods Twenty 3D-printed patient-specific titanium mesh GBR surgery cases were enrolled, in which 10 cases were minor bone defect/augmentation (the planned bone augmentation surface area is less than or equal to 150 mm2 or one tooth missing or two adjacent front-teeth/premolars missing) and another 10 cases were significant bone defect/augmentation (the planned bone augmentation surface area is greater than 150 mm2 or missing adjacent teeth are more than two (i.e. ≥ three teeth) or missing adjacent molars are ≥ two teeth). 3D digital reconstruction/superposition technology was employed to investigate the bone augmentation accuracy of 3D-printed patient-specific titanium meshes. Results There was no significant difference in the 3D deviation distance of bone augmentation between the minor bone defect/augmentation group and the major one. The contour lines of planned-CAD models in two groups were basically consistent with the contour lines after GBR surgery, and both covered the preoperative contour lines. Moreover, the exposure rate of titanium mesh in the minor bone defect/augmentation group was slightly lower than the major one. Conclusion It can be concluded that the size of the bone defect has no significant effect on the 3D accuracy of alveolar bone augmentation performed with the additively manufactured patient-specific titanium mesh.

The hot deformation behavior of dual-phase Mg–9Li–3Al alloys was investigated by the isothermal hot compression tests using the Gleeble-3500 thermal-mechanical simulation testing system over a temperature range from 473 to 623 K and a strain rate range of 0.001–1 s−1. The flow curves exhibited obvious serrations of periodic fluctuation at high strain rates, which can be considered as the Portevin-Le Chatelier effect. The relationship among flow stress, strain rate, and deformation temperature was analyzed. The deformation activation energy (Q) and some basic material factors (A, n, and α) were calculated based on the Zener–Hollomon equation. An approach of processing map composed of power dissipation and instability domains was established by the dynamic material model to reveal the hot workability. The flow instability domain only occurred at low temperatures and high strain rates. When the Mg–9Li–3Al alloy was deformed at 473 K and the strain rate of 1 s-1, numerous deformation twins were formed in α-Mg phases and, meanwhile, the β-Li phase was deformed and broken. When the temperature was increased to 573 K, the synergetic deformability between α-Mg and β-Li phases was improved due to the activation of more slip systems. However, the proportion of dynamic recrystallization was still low at the strain rate of 0.001 s-1. The needle-shaped α-Mg phase precipitated out in the β-Li matrix when the alloy was deformed at 623 K and the strain rate of 0.001 s-1. Its formation was attributed to the deformation-induced transformation. Moreover, the α-Mg phase can retard the dislocation movement and grain growth during deformation, leading to the precipitation/dispersion hardening.

This work investigates the compressive deformation behavior of as-extruded Mg-6Gd-1.6Y–1Zn-0.4Zr (VZ61) and Mg-6Gd-4.8Y–3Zn-0.4Zr (VZ63) alloys via uniaxial compressive tests at various deformation temperatures. At room temperature, compared with the VZ61 alloy, the compressive yield strength of the VZ63 alloy were obviously enhanced due to its increased amount of LPSO phase. Both alloys exhibited a three-stage strain hardening feature. The strain hardening rate first sharply decreases (stage I), then continues to increase at a slower rate (stage II) and finally decreases (stage III). At stage III, a larger number of dislocation accumulation around the kinked LPSO phase resulted in a higher strain hardening rate for VZ63 alloy than that for VZ61 alloy. During high temperature compression, the true stress–strain curves showed that the flow stress gradually reduced with increasing temperature and also the reducing of strain rate, and the VZ63 alloy displayed a higher peak stress than VZ61 alloy. Constitutive equations were constructed based on the true stress–strain to better understand the relation among flow tress (σ), strain rate (ε⋅) and deformation temperature (T) in VZ alloys during hot deformation. The results showed that the VZ63 alloy had a lower deformation activation energy (Q = 255.6 kJ/mol) than VZ61 alloy (Q = 395.5 kJ/mol). The DRX kinetic models of the VZ61 and VZ63 alloys were also established, indicating that the VZ63 alloy was more prone to DRX with a higher volume fraction of dynamically recrystallized grains (XDRX) at the same deformation conditions.

COVID-19 pandemic caused by the novel SARS-CoV-2 has impacted human livelihood globally. Strenuous efforts have been employed for its control and prevention; however, with recent reports on mutated strains with much higher infectivity, transmissibility, and ability to evade immunity developed from previous SARS-CoV-2 infections, prevention alternatives must be prepared beforehand in case. We have perused over 128 recent works (found on Google Scholar, PubMed, and ScienceDirect as of February 2023) on medicinal plants and their compounds for anti-SARS-CoV-2 activity and eventually reviewed 102 of them. The clinical application and the curative effect were reported high in China and in India. Accordingly, this review highlights the unprecedented opportunities offered by medicinal plants and their compounds, candidates as the therapeutic agent, against COVID-19 by acting as viral protein inhibitors and immunomodulator in (32 clinical trials and hundreds of in silico experiments) conjecture with modern science. Moreover, the associated foreseeable challenges for their viral outbreak management were discussed in comparison to synthetic drugs.

The additions of alloying elements can significantly improve the mechanical properties of magnesium (Mg) alloys, mainly due to the fact that their additions change the critical shear stresses (CRSS) for dislocation slips. In this work, experimental and computational methods were used to explore the mechanisms responsible for the roles of Sm element addition in affecting the mechanical properties of Mg. The results showed that the addition of Sm obviously improves the microstructure and mechanical properties. It promotes the formation of twins and beneficially activated the non-basal slip at the initial stage of plastic deformation, resulting in a high ductility. The Visco-Plastic Self-Consistent (VPSC) and the two-beam diffraction results confirmed that the pyramidal slip and prismatic slip were activated during tensile testing. The quantitative analysis of slip traces verified that the volume of non-basal slips reached 35 % after Sm addition. The additions of Sm with solid solution increased the activities of pyramidal dislocation during deformation, which was beneficial to accommodate the c-axis strain, and finally improved the room temperature ductility of Mg. First-principle calculations demonstrate that the solute Sm atoms would reduce the stacking fault energy for basal and prismatic slips.

In the present study, to understand the mechanism of Mn on inhibiting Fe-caused Mg corrosion, the corrosion behaviour of commercial pure Mg and Mg-6Mn alloy in 0.6 M NaCl solution is investigated. It is found that in Mg-6Mn alloy, Fe impurity is incorporated into Mn to form Mn (Fe) phase with Fe as solid solute. The initial galvanic corrosion cannot be reduced through converting Fe-rich phase to Mn (Fe) phase, since Mn (Fe) phase also has relatively strong cathodic activity and has much larger volume fraction than Fe-rich phase. However, the cathodic activation behaviour of pure Mg is inhibited. The cathodic activity even decreases for Mg-Mn alloy with increased exposure time, due to the reduced cathodic HER at the Mn (Fe) particles. Mn can be oxidized at the OCP of Mg-6Mn alloy, resulting in relatively dense Mn-rich corrosion film on particle surface, which separates the particle from the electrolyte and, consequently, inhibits HER.

The dynamic tensile properties and microstructural evolution of an extruded EW75 magnesium alloy deformed at ambient temperature and different high strain rates (from 1000 to 3000 s-1) along extrusion direction (ED) were investigated by Split Hopkinson Tension Bar (SHTB). The corresponding deformation mechanisms, texture evolution and microstructure changes were analyzed by optical microscope (OM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). The results show that the extruded EW75 magnesium alloy along ED exhibits a conventional positive strain rate sensitivity that the dynamic flow stresses increase with increasing strain rate. Texture measurements show that after dynamic tension, the initial weak texture of extruded EW75 magnesium alloy tansforms to a relatively strong //ED texture with increasing strain rates. The microstructural analysis demonstrates that dislocation motion are main deformatin mode to accommodate dynamic tensile deformation at high strain rates. In addition, the interactions of dislocation-dislocation and dislocation-second phase lead to the increase of flow stress and strain hardening with increasing strain rate.

Dental anatomy education for dental technology students should be developed in alignment with digital dental laboratory practices. We hypothesized that a virtually assisted sketching-based dental anatomy teaching module could improve students' acquisition of skills essential for digital restoration design. The second-year dental technology curriculum included a novel virtual technology-assisted sketching-based module for dental anatomy education. Pre- and post-course assessments evaluated students' skill sets and knowledge bases. Computer-aided design (CAD) scores were analyzed after one year to assess how the skills students developed through this module impacted their subsequent CAD performance. Participants who undertook the dental sketching-based teaching module demonstrated significantly improved theoretical knowledge of dental anatomy, dental aesthetic perception, and spatial reasoning skills. A partial least squares structural equation model indicated that the positive effects of this module on subsequent CAD performance were indirectly mediated by dental aesthetic perception, spatial reasoning, and practice time. A virtually assisted sketching-based dental anatomy teaching module significantly improved students' acquisition of skills and knowledge and positively mediated dental technology students' CAD performance.

Wrought magnesium alloys attract special interests as lightweight structural material due to their homogeneous microstructure and enhanced mechanical properties compared to as-cast alloys. In this contribution, recent research and developments on wrought magnesium alloys are reviewed from the viewpoint of the alloy design, focusing on Mg-Al, Mg-Zn and Mg-rare earth (RE) systems. The effects of different alloying elements on the microstructure and mechanical properties are described considering their strengthening mechanisms, e.g. grain refinement, precipitation and texture hardening effect. Finally, the new alloy design and also the future research of wrought magnesium alloys to improve their mechanical properties are discussed. Keywords: Wrought magnesium alloys, Alloy design, Mechanical properties

Mg–RE (Dy, Gd, Y) alloys show promising for being developed as biodegradable medical applications. It is found that the hydride REH2 could be formed on the surface of samples during their preparations with water cleaning. The amount of formed hydrides in Mg–RE alloys is affected by the content of RE and heat treatments. It increases with the increment of RE content. On the surface of the alloy with T4 treatment the amount of formed hydride REH2 is higher. In contrast, the amount of REH2 is lower on the surfaces of as-cast and T6-treated alloys. Their formation mechanism is attributed to the surface reaction of Mg–RE alloys with water. The part of RE in solid solution in Mg matrix plays an important role in influencing the formation of hydrides.

Previous investigations indicate that the creep resistance of magnesium alloys is proportional to the stability of precipitated intermetallic phases at grain boundaries. These stable intermetallic phases were considered to be effective to suppress the deformation by grain boundary sliding, leading to the improvement of creep properties. Based on this point, adding the alloying elements to form the stable intermetallics with high melting point became a popular way to develop the new creep resistant magnesium alloys. The present investigation, however, shows that the creep properties of binary Mg–Sn alloy are still poor even though the addition of Sn possibly results in the precipitation of thermal stable Mg2Sn at grain boundaries. That means other possible mechanisms function to affect the creep response. It is finally found that the poor creep resistance is attributed to the segregation of Sn at dendritic and grain boundaries. Based on this observation, new approaches to improve the creep resistance are suggested for magnesium alloys because most currently magnesium alloys have the commonality with the Mg–Sn alloys.

The present work investigates the influences of microalloying with rare earths on the mechanical properties of magnesium alloys. The amount of each rare earth element is controlled below 0.4 wt.% in order not to increase the cost of alloy largely. The synergic effects from the multi-microalloying with rare earths on the mechanical properties are explored. The obtained results show that the as-cast magnesium alloys multi-microalloying with rare earths possesses a quite high ductility with a tensile strain up to 25–30% at room temperature. Moreover, these alloys exhibit much better corrosion resistance than AZ31 alloy. The preliminary in situ neutron diffractions on the deformation of these alloys indicate that the multi-microalloying with rare earths seems to be beneficial for the activation of more slip systems. The deformation becomes more homogeneous and the resultant textures after deformation are weakened.

Purpose: Complex bone defects with a horizontal and vertical combined deficiency pose a clinical challenge in implant dentistry. This study reports the case of a young female patient who presented with a perforating bone defect in the aesthetic zone. Materials and methods: Based on prosthetically guided bone regeneration, virtual 3D bone augmentation was planned. A 3D printed customised titanium mesh and the autogenous bone ring technique were then utilised simultaneously to achieve a customised bone contour. After 6 months, the titanium mesh was removed and connective tissue grafting was performed. Finally, implants were placed and the provisional and definitive prostheses were delivered following a digital approach. Vertical and horizontal bone gain, new bone density, pseudo-periosteum type and marginal bone loss were measured. Planned bone volume, regenerated bone volume and regeneration rate were analysed. Results: Staged tooth shortening led to a coronal increase in keratinised mucosa. The customised titanium mesh and bone ring technique yielded 14.27 mm vertical bone gain and 12.9 mm horizontal bone gain in the perforating area. When the titanium mesh was removed, the reopening surgery showed a Type 1 pseudo-periosteum (none or < 1 mm), and CBCT scans revealed a new bone density of ~550 HU. With a planned bone volume of 1063.55 mm3, the regenerated bone volume was 969.29 mm3, indicating a regeneration rate of 91.14%. The 1-year follow-up after definitive restoration revealed no complications except for 0.55 to 0.60 mm marginal bone loss. Conclusion: Combined application of customised titanium mesh and an autogenous bone ring block shows promising potential to achieve prosthetically guided bone regeneration for complex bone defects in the aesthetic zone. [ABSTRACT FROM AUTHOR]

This study aimed to estimate the radiographic outcomes of the alveolar ridge splitting (ARS) technique combined with guided bone regeneration (GBR) and compare its efficacy with GBR alone in maxillary anterior narrow ridges. Forty patients with 51 implants in the ARS group and 40 patients with 49 implants in the GBR group were included. The buccal bone thickness (BBT) at 0 to 4 mm from the implant shoulder immediately and 6 months postoperative were analyzed using cone beam computed tomography. The BBT at both time points had no statistical disparities between the two groups (P > .05). However, BBT changes indicated significant disparities, with more BBT preservation in the ARS group (P < .05). Compared with GBR alone, the ARS technique combined with GBR, despite obvious buccal bone diminution, could be a reliable modality for treating ridge width deficiency in the anterior maxilla. [ABSTRACT FROM AUTHOR]