Search

Abstract Secondary zinc oxide dust is rich in high-grade metals such as Zn, In, Pb, and Ga, and in the face of the depletion of ore resources at home and abroad, it is of great significance to seek an efficient process to realize the full resource recovery of valuable metals in secondary zinc oxide dust. In this study, on the basis of the thermodynamic analysis of the wet treatment process, three wet treatment methods, namely “low acid leaching”, “high acid leaching” and “chlorination leaching”, were used to explore the suitable parameters for stepwise extraction of Zn, In and Pb metals. The results showed that the three wet treatment methods could effectively extract the corresponding main elements, and the optimal leaching rates of Zn, In and Pb were 73, 90 and 94%, respectively. Thermodynamic analysis shows that under ideal conditions, the “cascade separation” of some or all metals can be theoretically achieved by using a suitable leaching solvent for zinc oxide dust. The concentration of sulfuric acid, the ratio of liquid solid volume to mass and temperature had great effects on the leaching rate of Zn and In, and the leaching rate of Zn and In also increased with the increase of the values of the three experimental parameters, which was positively correlated. The leaching rate of Pb will increase with the increase of sulfuric acid concentration, but when the pH of the solution system is

Abstract Background No specific triglyceride-lowering therapy is recommended in patients with hypertriglyceridemia-associated acute pancreatitis (HTG-AP), primarily because of the lack of quality evidence. This study aimed to describe practice variations in triglyceride-lowering therapies for early HTG-AP patients and assess whether more rapid triglyceride decline is associated with improving organ failure. Methods This is a multicentre, prospective cohort study recruiting HTG-AP patients with elevated plasma triglyceride (> 11.3 mmol/L) admitted within 72 h from the onset of symptoms. Patients were dichotomised on study day 3 into either target reaching (plasma triglyceride ≤ 5.65 mmol/L) or not. The primary outcome was organ failure-free days (OFFD) to 14 days of enrolment. The association between target-reaching and OFFD was modelled. Additionally, the slope in plasma triglyceride over the first three days in response to treatment was calculated, and its association with OFFD was assessed as a sensitivity analysis. Results Among the 300 enrolled patients, 211 underwent exclusive medical treatment, and 89 underwent various blood purification therapies. Triglyceride levels were available in 230 patients on study day 3, among whom 122 (53.0%) had triglyceride levels of ≤ 5.65 mmol/l. The OFFD was not different between these patients and those in whom plasma triglyceride remained > 5.65 mmol/L [median (IQR): 13 (10–14) vs. 14 (10–14), p = 0.46], even after adjustment for potential confounders. For the decline slopes, there was no significant change in OFFD with a steeper decline slope [risk difference, − 0.088, 95% CI, − 0.334 to 0.158, p = 0.48]. Conclusions Triglyceride-lowering therapies vary greatly across centres. More rapid triglyceride decline was not associated with improving incidence and duration of organ failure.

Abstract Purpose This study aimed to assess the therapeutic efficacy of Reiki therapy in alleviating anxiety. Methods In adherence to academic standards, a thorough search was conducted across esteemed databases such as PubMed, Web of Science, Science Direct, and the Cochrane Library. The primary objective of this search was to pinpoint peer-reviewed articles published in English that satisfied specific criteria: (1) employing an experimental or quasi-experimental study design, (2) incorporating Reiki therapy as the independent variable, (3) encompassing diverse patient populations along with healthy individuals, and (4) assessing anxiety as the measured outcome. Results The study involved 824 participants, all of whom were aged 18 years or older. Reiki therapy was found to have a significant effect on anxiety intervention(SMD=-0.82, 95CI -1.29∼-0.36, P = 0.001). Subgroup analysis indicated that the types of subjects (chronically ill individuals and the general adult population) and the dosage/frequency of the intervention (≤ 3 sessions and 6–8 sessions) were significant factors influencing the variability in anxiety reduction. Conclusion Short-term Reiki therapy interventions of ≤ 3 sessions and 6–8 sessions have demonstrated effectiveness in reducing health and procedural anxiety in patients with chronic conditions such as gastrointestinal endoscopy inflammation, fibromyalgia, and depression, as well as in the general population. It is important to note that the efficacy of Reiki therapy in decreasing preoperative anxiety and death-related anxiety in preoperative patients and cancer patients is somewhat less consistent. These discrepancies may be attributed to individual pathophysiological states, psychological conditions, and treatment expectations.

Abstract Pneumatic artificial muscles can move continuously under the power support of air pumps, and their flexibility also provides the possibility for applications in complex environments. However, in order to achieve operation in confined spaces, the miniaturization of artificial muscles becomes crucial. Since external attachment devices greatly hinder the miniaturization and use of artificial muscles, we propose a light-driven approach to get rid of these limitations. In this study, we report a miniaturized fiber-reinforced artificial muscle based on mold editing, capable of bending and axial elongation using gas-liquid conversion in visible light. The minimum volume of the artificial muscle prepared using this method was 15.7 mm3 (d = 2 mm, l = 5 mm), which was smaller than those of other fiber-reinforced pneumatic actuators. This research can promote the development of non-tethered pneumatic actuators for rescue and exploration, and create the possibility of miniaturization of actuators.

β-carotene (BC) has various biological activities, such as anticancer properties, contributing to the prevention of cardiovascular diseases, etc., while the poor solubility and low bioavailability limit its further development in the food industry. Therefore, how to effectively encapsulate this unstable substance has become a hot topic. Here, different concentrations of sodium caseinate and ι-carrageenan (NaCas-CA) complex emulsions were used as wall materials, and the effect of spray-drying (SD) and vacuum freeze-drying (VFD) on the properties of BC powders loaded with NaCas-CA was investigated. The results showed that the characteristic peaks of BC disappeared in all powdered oils, indicating that BC could be effectively encapsulated. As the wall concentration increased, the surface oil of the powders decreased significantly. At the same concentration, the surface oil content of SD (minimum of 8.34%) was lower than that of VFD (minimum of 10.02%). However, the particle size of SD-reconstituted emulsions was larger than that of VFD. Furthermore, the SD-reconstituted emulsions were more stable than the VFD after storage at 25 °C for 3 h. This study reveals the effect of different drying methods on the structure and stability of powdered oils, providing valuable information for the research of functional active-loaded powdered oils and applications in the food industry.

Objective: The objective of this study was to explore the influence of traditional laparoscopic surgery and transumbilical single-port laparoscopic surgery on ovarian function in patients with benign ovarian tumours. Materials and Methods: Forty-four patients with benign ovarian tumours who were treated in our hospital from January 2020 to June 2021 were selected and randomly divided into two groups, with 22 cases in each group according to random number table. The conventional group was treated with conventional laparoscopic surgery, while the modified group was treated with transumbilical single-port laparoscopic surgery. The measurement method was t-test, and the enumeration method was two tests. The clinical operation-related indicators, ovarian function (follicle-stimulating hormone, E2 and luteinising hormone), complication incidence, Visual Analogue Scale (VAS) and landscaping satisfaction scores of the two groups were compared. Results: There were no significant differences in complications and operation duration between the two groups (P > 0.05). After treatment, the ovarian function indexes and beautification satisfaction scores of the modified group were significantly superior to those of the conventional group (P < 0.05). Besides, the intraoperative bleeding volume, post-operative exhaust time, hospital stay and three-dimensional VAS scores on day 1 and day 3 after surgery of the modified group were lower than those of the conventional group (P < 0.05). Conclusion: Transumbilical single-port laparoscopic surgery for benign ovarian tumours has a significant clinical effect, which can effectively reduce bleeding during the operation, improve ovarian function, relieve surgical pain, promote rapid post-operative recovery and improve patients' satisfaction with landscaping. It is worthy of clinical application.

In mammals, gonadal somatic cell lineage differentiation determines the development of the bipotential gonad into either the ovary or testis. Sertoli cells, the only somatic cells in the spermatogenic tubules, support spermatogenesis during gonadal development. During embryonic Sertoli cell lineage differentiation, relevant genes, including WT1, GATA4, SRY, SOX9, AMH, PTGDS, SF1, and DMRT1, are expressed at specific times and in specific locations to ensure the correct differentiation of the embryo toward the male phenotype. The dysregulated development of Sertoli cells leads to gonadal malformations and male fertility disorders. Nevertheless, the molecular pathways underlying the embryonic origin of Sertoli cells remain elusive. By reviewing recent advances in research on embryonic Sertoli cell genesis and its key regulators, this review provides novel insights into sex determination in male mammals as well as the molecular mechanisms underlying the genealogical differentiation of Sertoli cells in the male reproductive ridge.

Objectives: To determine whether tinnitus negatively impacts the accuracy of sound source localization in participants with normal hearing. Methods: Seventy-five participants with tinnitus and 74 without tinnitus were enrolled in this study. The accuracy of sound source discrimination on the horizontal plane was compared between the two participant groups. The test equipment consisted of 37 loudspeakers arranged in a 180° arc facing forward with 5° intervals between them. The stimuli were pure tones of 0.25, 0.5, 1, 2, 4, and 8 kHz at 50 dB SPL. The stimuli were divided into three groups: low frequency (LF: 0.25, 0.5, and 1 kHz), 2 kHz, and high frequency (HF: 4 and 8 kHz) stimuli. Results: The Root Mean Square Error (RMSE) score of all the stimuli in the tinnitus group was significantly higher than that in the control group (13.45 ± 3.34 vs. 11.44 ± 2.56, p = 4.115, t

The problem of large stockpiles of red mud needs to be solved, and the use of red mud to prepare inorganic fibers is a new way of applying red mud on a large scale. The role of CaO/Al2O3 in the melting point and melt structure of red mud was investigated by molecular dynamics simulations and thermodynamic calculations. Liquid phase line temperatures for different CaO/Al2O3 systems were calculated using the Factsage program. The radial distribution function and the type of oxygen bonding were used to characterize the effect of different CaO/Al2O3 on the structure of the red mud melt. The melting point of MgAl2O4 is lower than that of CaTiO3 due to the fact that the type of oxygen bonding in MgAl2O4 is predominantly bridging oxygen bonds. When the red mud system has a low SiO2 content and CaO/Al2O3 is between 0.3 and 3.9, the melting point temperature increases significantly, which is not conducive to the fibrillation of the red mud melt.

Multi-source ferrous metallurgical dust and sludge are significant components of iron-containing solid waste in the iron and steel industry. It is crucial for the sustainable operation of steel enterprises to recycle iron from ferrous metallurgical dust and sludge (FMDS) for use in steel smelting. However, besides Fe, FMDS also contains valuable elements such as Zn, Pb, K, and Na, among others. While these valuable elements hold high recovery value, they impede the direct reuse of FMDS by iron and steel enterprises. This paper introduces the compositional characteristics of multi-source ferrous metallurgical dust and sludge, analyzes the main recycling technologies associated with FMDS at the present stage of development, and discusses the characteristics of different technologies. In view of this, a new idea of the “cooperative treatment of multi-source ferrous metallurgical dust and sludge—full quantitative recovery of valuable elements” is put forward. This new idea integrates a variety of treatment processes to directly recycle FMDS within the steel plant, enhancing the adequacy of dust and sludge recovery and reducing the risk of environmental pollution. This paper provides a reference for achieving the full quantification and utilization of high-value-added FMDS in steel plants.

The preparation of high-quality inorganic fibers by centrifugation from modified melting-separated red mud, which is the product of the efficient recovery of pig iron from red mud, is a new approach to achieve large-scale production of high value-added materials from red mud. This method has a wide range of application prospects and could contribute substantially to the comprehensive utilization of bulk industrial solid waste and the development of a circular economy. In this study, melting-separated red mud was modified with water-quenched blast furnace slag, quartz sand, and quicklime. The effect of the CaO/Na2O mass ratio on the viscosity, fluidity, and crystallization performance of the melting-separated red mud was investigated; slag wool was prepared by centrifugation under laboratory conditions; and the effect of the CaO/Na2O mass ratio on the morphology and properties of the slag wool was investigated. The viscosity of modified melting-separated red mud with different CaO/Na2O mass ratios shows a decreasing trend with increasing temperature, and the fluidity increases with increasing temperature, indicating that the melt fluidity is improved. The suitable fiber-forming temperature of the melting-separated red mud shows a trend of increasing–decreasing–increasing with an increasing CaO/Na2O mass ratio, and at a CaO/Na2O ratio of 3.0, the maximum suitable fiber-forming temperature is 81 °C. Considering the feasibility of slag wool preparation from modified melting-separated red mud, the CaO/Na2O of the modified raw material system should not be higher than 3.0. The crystallization temperature of modified melting-separated red mud with different CaO/Na2O mass ratios first increases and then decreases, with a peak of 1450 °C at a CaO/Na2O ratio of 4.0. Slag wool prepared from modified melting-separated red mud with different CaO/Na2O mass ratios exhibits good properties, with a diameter of 5.47–6.67 µm and a slag ball content of 2.7–8.4%.

This study adopted molecular dynamics to investigate the influence of C28H58 mass fraction on the structure and phase change of C28H58/C22H46 n-alkane mixtures at different temperatures; systematically analyzed the C–H and C–C bond lengths, changes in the H–C–H bond angle and C–C–C–C torsion angle, and energy conversions within the mixture during heating of C28H58/C22H46 n-alkane mixtures; calculated the self-diffusion coefficient (D) by combining the Einstein relation and mean squared displacement; and determined the phase change temperature of each mixture according to the relationship between D and temperature. The results show that, at 280 K, changing the mass fraction of C28H58 does not affect the C–H and C–C bond lengths and the H–C–H bond angle. At 350 K, the C–H bond length decreases with the increase in the mass fraction of C28H58, the C–C bond length increases slightly when the mass fraction is 65.2% and remains unchanged for other mass fractions, and the H–C–H bond angle slightly decreases. With an increase in temperature, the peak intensity of the stretched conformation at ±180° gradually decreases, while the peak of the twisted conformation appears around ±70°, and the degree of twist of the C–C–C–C dihedral angle in the mixture increases. The phase change temperature begins to increase slowly with the increase in the mass fraction of C28H58, and the phase change temperature increases rapidly when the mass fraction exceeds 65.2%. The kinetic and potential energies of the mixture tend to increase with the increasing mass fraction of C28H58.

Spatial processing is a major cognitive function of hearing. Sound source localization is an intuitive evaluation of spatial hearing. Current evidence of the effect of tinnitus on sound source localization remains limited. The present study aimed to investigate whether tinnitus affects the ability to localize sound in participants with normal hearing and whether the effect is related to the type of stimulus. Overall, 40 participants with tinnitus and another 40 control participants without tinnitus were evaluated. The sound source discrimination tasks were performed on the horizontal plane. Pure tone (PT, with single frequency) and monosyllable (MS, with spectrum information) were used as stimuli. The root-mean-square error (RMSE) score was calculated as the mean target response difference. When the stimuli were PTs, the RMSE scores of the control and tinnitus group were 11.77 ± 2.57° and 13.97 ± 4.18°, respectively. The control group performed significantly better than did the tinnitus group (t = 2.841, p = 0.006). When the stimuli were MS, the RMSE scores of the control and tinnitus groups were 7.12 ± 2.29° and 7.90 ± 2.33°, respectively. There was no significant difference between the two groups (t = 1.501, p = 0.137). Neither the effect of unilateral or bilateral tinnitus (PT: t = 0.763, p = 0.450; MS: t = 1.760, p = 0.086) nor the effect of tinnitus side (left/right, PT: t = 0.389, p = 0.703; MS: t = 1.407, p = 0.179) on sound localization ability were determined. The sound source localization ability gradually deteriorated with an increase in age (PT: r2 = 0.153, p < 0.001; MS: r2 = 0.516, p = 0.043). In conclusion, tinnitus interfered with the ability to localize PTs, but the ability to localize MS was not affected. Therefore, the interference of tinnitus in localizing sound sources is related to the type of stimulus.

At this stage,the Internet of things (IoT) customer business is developing rapidly.The management problems of weak customer operation ability have gradually exposed in the IoT industry,resulting in the low AP (analytical processing) value of customers,the low profitability and high operating cost.Therefore,it is urgent to enhance the massive data analysis capabilities of the IoT to provide data guidance for business development.To improve the customer value,big data technology,multi-dimensional analysis technology and massive query technology were used to make portraits of IoT enterprise customers,and realize the construction of the customer data platform with refined and efficient operation services.It was introduced how to construct the data operation platform from the aspect of technology implementation.

Abstract This paper investigates the event-triggered sampled-data synchronization problem of complex networks with time-varying coupling delays. The sampled-data controller is designed with event-triggered mechanisms. Some results in terms of a linear matrix inequality are obtained to guarantee the asymptotical synchronization of complex networks with time-varying coupling delays. Lastly, we test the effectiveness of the proposed method via some numerical examples.

In recent years,with the increasingly complex and large-scale evolution of IT systems,objectively higher requirements have been placed on IT operation and maintenance technology.From the perspective of blockchain Raft consensus algorithm technology,the application of blockchain technology in intelligent operation and maintenance system was elaborated.By comparing the blockchain technology with the traditional technology,a new architecture and some reconstruction difficulties to solve the existing problems were provided,to realize a smart operation and maintenance system based on the blockchain technology.

Abstract Background The prevalence of myopia and associated risk factors among children in Chongqing has not yet been determined. This study investigated the prevalence of myopia and possible relationships between myopia and several related factors among school children in Chongqing. Methods This cross-sectional study assessed a sample of 997 children (7–13 years of age) attending primary school in Chongqing. Data were obtained from visual acuity and refractive error measurements and a structured questionnaire. Myopia was defined as visual acuity

Using fly ash as the modifier, blast furnace slag was modified to prepare slag wool, fulfilling the goal of using one type of waste to make use of another type of waste, and it is of great significance for the comprehensive utilization of industrial bulk solid wastes and resource recycling. In the process of forming fiber from blast furnace slag, fluidity is the key factor affecting the smooth formation of fiber from slag. To explore the changes in the fluidity of modified blast furnace slag, the temperature-dependent viscosity of modified blast furnace slag with different amounts of fly ash added was measured, and the effects of fly ash addition on the viscosity, fluidity, and activation energy of particle migration, and slag structure of modified blast furnace slag were investigated. The results indicated that with the increase in the amount of fly ash added, in the high-temperature region (>1324 °C), the viscosity of modified blast furnace slag increases gradually, the fluidity decreases gradually (i.e., the fluidity becomes worse), and the suitable fiber-forming temperature range gradually widens. When the fly ash addition increases from 5% to 25%, the trend of the activation energy of slag particle migration is as follows: increase, decrease, increase significantly, decrease. When the addition of fly ash is less than 20%, the SiO2 content and slag temperature jointly affect the breakage and reorganization of oxygen bridge bonding in the silicon-oxygen tetrahedron in the slag structure. When the addition of fly ash increases to 25%, the slag temperature dominates the breakage of oxygen bridge bonding in the silicon-oxygen tetrahedron in the slag structure. When using fly ash as the modifier to prepare slag wool, from the perspective of slag fluidity and process operability, the optimum addition amount of fly ash is 15%.

Abstract Background It is widely accepted that mitochondria have a direct impact on neuronal function and survival. Oxidative stress caused by mitochondrial abnormalities play an important role in the pathophysiology of lipopolysaccharide (LPS)-induced memory impairment. Elamipretide (SS-31) is a novel mitochondrion-targeted antioxidant. However, the impact of elamipretide on the cognitive sequelae of inflammatory and oxidative stress is unknown. Methods We utilized MWM and contextual fear conditioning test to assess hippocampus-related learning and memory performance. Molecular biology techniques and ELISA were used to examine mitochondrial function, oxidative stress, and the inflammatory response. TUNEL and Golgi-staining was used to detect neural cell apoptosis and the density of dendritic spines in the mouse hippocampus. Results Mice treated with LPS exhibited mitochondrial dysfunction, oxidative stress, an inflammatory response, neural cell apoptosis, and loss of dendritic spines in the hippocampus, leading to impaired hippocampus-related learning and memory performance in the MWM and contextual fear conditioning test. Treatment with elamipretide significantly ameliorated LPS-induced learning and memory impairment during behavioral tests. Notably, elamipretide not only provided protective effects against mitochondrial dysfunction and oxidative stress but also facilitated the regulation of brain-derived neurotrophic factor (BDNF) signaling, including the reversal of important synaptic-signaling proteins and increased synaptic structural complexity. Conclusion These findings indicate that LPS-induced memory impairment can be attenuated by the mitochondrion-targeted antioxidant elamipretide. Consequently, elamipretide may have a therapeutic potential in preventing damage from the oxidative stress and neuroinflammation that contribute to perioperative neurocognitive disorders (PND), which makes mitochondria a potential target for treatment strategies for PND.

China Unicom’s challenges and appeals in the operation capabilities of IoT customers were briefly analyzed.Combined with the big data analysis capabilities of China Unicom Research Insitute,a complete standard system was built.The scale of IoT applications was promoted and the goal of IoT customer operations big data was realized.Based on the practical experience of the IoT operating model in the telecom industry,how to implement more refined enterprise customer operations for operators based on big data capabilities was described.To achieve the accuracy and efficiency of customer service services from the perspective of technological innovation,how to use data analysis capabilities to build accurate customer support systems was explored.Finally,the important value of big data applied in customer operation scenarios and the prospect of customer operation were described.

The process of granulation in blast furnace slag (BFS) by gas quenching can effectively recover the waste heat of BFS and improve the value-added nature of the BFS byproduct. With decreasing temperature, BFS crystallizes into melilite, anorthite, spinel, etc. Mineral crystallization, however, is not conducive to the production of amorphous BFS beads. This study uses thermodynamic simulation and remelting experiments to study the influences of basicity, acidity, and the MgO and Al2O3 content of the BFS on the crystallization. By controlling the composition of the BFS, mineral crystallization in the process of granulation in BFS, by gas quenching, could be prevented. The results show that increasing the basicity of the BFS causes the mineral crystallization temperature to increase rapidly. The mineral phase then crystallizes at a higher temperature, which is not conducive to the formation of an amorphous phase. Increasing the acidity of the BFS can greatly decrease the crystallization temperature, e.g., when the acidity increases to 1.3, amorphous BFS beads can be obtained at the gas quenching temperature (1623 K). Although increasing the MgO and Al2O3 contents in the BFS had little effect on the crystallization temperature and yield, the preparation of amorphous BFS beads by gas quenching could be realized by adjusting the acidity of the BFS.

Pipeline inspection gauges (PIGs) are widely used for nondestructive testing of oil and natural gas pipelines, while above ground markers (AGMs) can locate and track the PIG through a variety of methods, including magnetic flux leakage signals, acoustic signals, and extremely low-frequency (ELF) magnetic signals. Traditional AGMs have the disadvantages of low positioning accuracy and only one-dimensional tracking capability. In this paper, a newly-designed PIG tracking system based on the ELF magnetic field is proposed by assembling dual receivers. Moreover, this paper develops a magnetic field sign-integration algorithm to achieve high-precision and four-dimensional (4-D) tracking of PIG. The simulation and experiment results demonstrate that the tracking system has the capability of 4-D tracking. In comparison with the previously published work, the designed tracking system improves the positioning accuracy and orientation tracking accuracy by more than 50%. The dual receivers tracking system also has the characteristic of high-robustness. Even in the state of lateral offset or tilt, it can still achieve accurate tracking of PIG. The realization of PIG’s high-precision 4-D tracking can improve the accuracy of defect location. Moreover, it can also provide the latest pipeline network layout and facilitate pipeline maintenance and pipeline surveying applications.

General control non-derepressible-2 (GCN2) is a ubiquitous protein kinase that phosphorylates the α subunit of the eukaryotic initiation factor, eIF2, preventing the initiation of a new cycle of protein synthesis, subsequently reducing the global protein biosynthesis. GCN2 can also regulate the response of plants to biotic and abiotic stresses. In this study, two GCN2 homologs, NtGCN2-1 and NtGCN2-2, were cloned from Nicotiana tabacum, and were predicted to have been derived from their progenitors in N. tomentosiformis and N. sylvestris, respectively. The phosphorylation of NteIF2α could be activated by promoting the expression of NtGCN2 with plant hormones, including salicylic acid (SA), azelaic acid (AZA), methyl jasmonate (MeJA), and by imposition of different stresses (Bemisia tabaci infection, drought, and cold), indicating that NtGCN2 is involved in the response of plants to multiple biotic and abiotic stresses. We also observed that the overexpression of NtGCN2-1 significantly influenced different physiological processes. It promoted seed germination and root elongation. The content of total soluble sugars and reducing sugars were decreased, whereas those of chlorophyll a and b were increased in the GCN2 overexpressing plants. In addition, the overexpressing plants had lower content of reactive oxygen species and exhibited higher antioxidant activities. These physiological alterations could be attributed to the changes in the endogenous phytohormones, decrease in the SA and abscisic acid content, and accumulation of MeJA and AZA. It indicated that the overexpression of NtGCN2 in tobacco, stimulated the plant defense responses via phosphorylation of NteIF2α and regulation of plant hormones, and changes in the antioxidant ability and plant nutrient status.

Video streaming communication networks will be a very important way to send multimedia information anytime and anywhere, and the construction of the network base station which transmits signals is crucial in future. However, there is a contradiction between the power consumption of LoRa nodes and the real-timeliness of mesh network. In order to solve the contradiction, this article aims to combine the mesh network of LoRa wireless communication system with an improved artificial bee colony algorithm. Specifically, an artificial bee colony algorithm, which is based on RBF radial basis neural network trained with random gradient method, is designed. Simulation results show that the proposed algorithm solves the contradiction between power consumption and real-timeliness effectively. When using this improved network system structure to send multimedia information, it shows obvious superiority in terms of the high efficiency and real-timeliness of multimedia transmission.

This paper is concerned with the reliable finite frequency filter design for networked control systems (NCSs) subject to quantization and data missing. Taking into account quantization, possible data missing and sensor stuck faults, NCSs are modeled in the framework of discrete time-delay switched systems, and the finite frequency l2 gain is adopted for the filter design of discrete time-delay switched systems, which is converted into a set of linear matrix inequality (LMI) conditions. By the virtues of the derived conditions, a procedure of reliable filter synthesis is presented. Further, the filter gains are characterized in terms of solutions to a convex optimization problem which can be solved by using the semi-definite programme method. Finally, an example is given to illustrate the effectiveness of the proposed method.