Search

A large variety of barriers can affect longitudinal connectivity, which leads to shipping blocking and even flood hazard. However, few existing methods can quantify physically the river channel connectivity from the barrier’s details perspective in a watershed. This paper establishes a new model of the River Channel Connectivity Index (RCCI) to quantify the unobstructed degree of river flow in river channels within geographic information system (GIS ) platforms based on the modified concept of time accessibility. A comprehensive classification system of barriers is setup before these barriers are identified by the remote sensing technology. The model is applied to Dashi Watershed in suburban Beijing, China. Results show that submersible bridges and sediment siltation are the main barriers in the watershed. RCCI values in the mountainous areas are generally higher than that of the plains. The assessment results verified by two historical flood events show that the RCCI can reveal where the river channel connectivity is impaired, how serious it is, and what the reason is for managers. Through scenarios’ results, the best restoration measure for each tributary is obtained from the perspective of reducing flood hazards. The new RCCI method not only has methodological significance, but also helps policymakers to enhance river flooding reduction and determine restoration priorities of the river channel.

Reports on the characterization of amyotrophic lateral sclerosis by selective motor neuron degeneration. Possible involvement of an apoptotic pathway; Quantification of the caspase-1 and -3 messenger RNA in single motor neurons and neighboring glial cells isolated from the spinal ventral horn of mutant SOD1 transgenic mice and littermates.

Objective: This study evaluated the wear of an antagonist and friction and wear properties of dental zirconia ceramic that was subjected to microwave and conventional sintering methods., Methods: Ten specimens were fabricated from Lava brand zirconia and randomly assigned to microwave and conventional sintering groups. A profile tester for surface roughness was used to measure roughness of the specimens. Wear test was performed, and steatite ceramic was used as antagonist. Friction coefficient curves were recorded, and wear volume were calculated. Finally, optical microscope was used to observe the surface morphology of zirconia and steatite ceramics. Field emission scanning electron microscopy was used to observe the microstructure of zirconia., Results: Wear volumes of microwave and conventionally sintered zirconia were (6.940±1.382)×10⁻², (7.952±1.815) ×10⁻² mm³, respectively. Moreover, wear volumes of antagonist after sintering by the considered methods were (14.189±4.745)×10⁻², (15.813±3.481)×10⁻² mm³, correspondingly. Statistically significant difference was not observed in the wear resistance of zirconia and wear volume of steatite ceramic upon exposure to two kinds of sintering methods. Optical microscopy showed that ploughed surfaces were apparent in zirconia. The wear surface of steatite ceramic against had craze, accompanied by plough. Scanning electron microscopy showed that zirconia was sintered compactly when subjected to both conventional sintering and microwave methods, whereas grains of zirconia sintered by microwave alone were smaller and more uniform., Conclusions: Two kinds of sintering methods are successfully used to produce dental zirconia ceramics with similar friction and wear properties.
.

Objective: To evaluate the effect of microwave sintering on the translucency of zirconia and to compare these effect with those of conventional sintering. The relationship between the microstructure of specimens and translucency was investigated., Methods: A total of 10 disc-shaped specimens were fabricated from 2 commercial brands of zirconia, namely, Zenostar and Lava. Each group included 5 discs. Conventional sintering was performed according to the manufacturers' specifications. The maximum temperature for Zenostar was 1,490 °C, whereas that for Lava was 1,500 °C. The dwelling time was 2 h. The sintering temperature for microwave sintering was 1,420 °C, heating rate was 15 °C · min⁻¹, and dwelling time was 30 min. After sintering, the translucency parameter (TP) of the specimens were measured with ShadeEye NCC. The sintered density of the specimens was determined by Archimedes' method. The grain size and microstructure of the specimens were investigated by scanning electron microscopy., Results: Density and translucency slightly increased by microwave sintering, but no significant difference was found between microwave and conventional sintering (P > 0.05). Small and uniform microstructure were obtained from microwave sintering. The mean TP of Lava was significantly higher than that of Zenostar (P < 0.001)., Conclusion: The translucency of zirconia sintered by microwave sintering is similar to that of the zirconia sintered by conventional sintering.