Search

Compton imaging has been used for various applications including astronomical observations, radioactive waste management, and biomedical imaging. The positions of radioisotopes are determined in the intersections of multiple cone traces through a large number of events, which reduces signal to noise ratio (SNR) of the images. We have developed an advanced Compton imaging method to localize radioisotopes with high SNR by using information of the interactions of Compton scattering caused by two gamma rays at the same time, as the double photon coincidence Compton imaging method. The targeted radioisotopes of this imaging method are specific nuclides that emit several gamma rays at the same time such as 60 Co, 134 Cs, and 111 In, etc. Since their locations are determined in the intersections of two Compton cones, the most of cone traces would disappear in the three-dimensional space, which enhances the SNR and angular resolution. In this paper, the comparison of the double photon coincidence Compton imaging method and the single photon Compton imaging method was conducted by using GEANT4 Monte Carlo simulation.

Compton imaging is a promising gamma-ray imaging method based on the Compton scattering kinematics due to high Compton scattering probability for sub-MeV to MeV gamma-rays. A conventional Compton camera has a disadvantage of low signal-to-background ratio (SBR), which is caused by drawing of multiple Compton cones. A method to solve this fundamental problem is the double-photon emission computed tomography (DPECT), which uses the coincidence detection for cascade gamma-rays and significantly increases the SBR using intersections of two Compton cones. In this study, we demonstrated the DPECT method by using 134Cs radio isotope, which is one of important radioisotopes for the imaging of fuel debris, with two Ce:Gd 3 (Al,Ga) 5 O12 (GAGG) scintillator Compton cameras.

This paper describes a modification method which strengthens forms for deriving diverse design solutions in structural design. In the early process of design, diverse design ideas are generated from a global solution search under unclear design conditions. In the past study, we have proposed the emergent design system, which allows a global solution search under limited design conditions to derive diverse design solutions. The proposed system derives geometrically novel in forms, but most of them do not satisfy the evaluation standard so that they are not applicable as solutions. Therefore, if we can modify these forms to applicable solutions, the diversity of applicable solutions would increase. In this paper, we propose a modification method which satisfies the evaluation standard by increasing and decreasing elements, and show the possibility of increasing the diversity of solutions.

Single photon emission computed tomography(SPECT) is a useful medical imaging modality using single photon detection from radioactive tracers, such as 99Tc and 111In, however further development of increasing the contrast in the image is still under investigation. A novel method (Double Photon Emission CT / DPECT) using a coincidence detection of two cascade gamma-rays from 111In is proposed and characterized in this study. 111In, which is well-known and commonly used as a SPECT tracer, emits two cascade photons of 171 keV and 245 keV with a short delay of approximately 85 ns. The coincidence detection of two gamma-rays theoretically determines the position in a single point compared with a line in single photon detection and increases the signal to noise ratio drastically. A fabricated pixel detector for this purpose consists of 8 × 8 array of high-resolution type 1.5 mm thickness Ce:GAGG (3.9% @ 662 keV, 6.63g/cm3, C&A Co. Ce:Gd3Ga2.7Al2.3O12 2.5 × 2.5 × 1.5 mm3) crystals coupled a 3 mm pixel SiPM array (Hamamatsu MPPC S13361-2050NS-08). The signal from each pixel is processed and readout using time over threshold (TOT) based parallel processing circuit to extract the energy and timing information. The coincidence was detected by FPGA with the frequency of 400 MHz. Two pixel detectors coupled to parallel-hole collimators are located at the degree of 90 to determine the position and coincidence events (time window =1 μs) are detected and used for making back-projection image. The basic principle of DPECT is characterized including the detection efficiency and timing resolution.

Compton imaging is a useful method to localize gamma sources without using mechanical collimators. In conventional Compton imaging, the incident directions of gamma rays are estimated in a cone for each event by analyzing the sequence of interactions of each gamma ray followed by Compton kinematics. Since the information of the ejection directions of the recoil electrons is lost, many artifacts in the shape of cone traces are generated, which reduces signal-to-noise ratio (SNR) and angular resolution. We have developed an advanced Compton imaging system with the capability of tracking recoil electrons by using a combination of a trigger-mode silicon-on-insulator (SOI) pixel detector and a GAGG detector. This system covers the 660–1330 keV energy range for localization of contamination nuclides such as 137Cs and 134Cs inside the Fukushima Daiichi Nuclear Power Plant in Japan. The ejection directions of recoil electrons caused by Compton scattering are detected on the micro-pixelated SOI detector, which can theoretically be used to determine the incident directions of the gamma rays in a line for each event and can reduce the appearance of artifacts. We obtained 2-D reconstructed images from the first iteration of the proposed system for 137Cs, and the SNR and angular resolution were enhanced compared with those of conventional Compton imaging systems.