Search

We have demonstrated that photo-thin film transistors (photo-TFTs) fabricated via a simple defect-generating process could achieve fast recovery, a high signal to noise (S/N) ratio, and high sensitivity. The photo-TFTs are inverted-staggered bottom-gate type indium-gallium-zinc-oxide (IGZO) TFTs fabricated using atomic layer deposition (ALD)-derived Al2O3 gate insulators. The surfaces of the Al2O3 gate insulators are damaged by ion bombardment during the deposition of the IGZO channel layers by sputtering and the damage results in the hysteresis behavior of the photo-TFTs. The hysteresis loops broaden as the deposition power density increases. This implies that we can easily control the amount of the interface trap sites and/or trap sites in the gate insulator near the interface. The photo-TFTs with large hysteresis-related defects have high S/N ratio and fast recovery in spite of the low operation voltages including a drain voltage of 1 V, positive gate bias pulse voltage of 3 V, and gate voltage pulse width of 3 V (0 to 3 V). In addition, through the hysteresis-related defect-generating process, we have achieved a high responsivity since the bulk defects that can be photo-excited and eject electrons also increase with increasing deposition power density.

Highly repeatable and recoverable phototransistors were explored using a "multifunctional channels" structure with multistacked chalcogenide and oxide semiconductors. These devices were made of (i) photoactive CdS (with a visible band gap), (ii) fast charge transporting ZnO (with a high field-effect mobility), and (iii) a protection layer of Al2O3 (with high chemical durability). The CdS TFT without the Al2O3 protection layer did not show a transfer curve due to the chemical damage that occurred on the ZnO layer during the chemical bath deposition (CBD) process used for CdS deposition. Alternatively, compared to CdS phototransistors with long recovery time and high hysteresis (ΔVth = 19.5 V), our "multi-functional channels" phototransistors showed an extremely low hysteresis loop (ΔVth = 0.5V) and superior photosensitivity with repeatable high photoresponsivity (52.9 A/W at 400 nm). These improvements are likely caused by the physical isolation of the sensing region and charge transport region by the insertion of the ultrathin Al2O3 layer. This approach successfully addresses some of the existing problems in CdS phototransistors, such as the high gate-interface trap site density and high absorption of molecular oxygen, which originate from the polycrystalline CdS.

In this paper, a simple and controllable "wet pulse annealing" technique for the fabrication of flexible amorphous InGaZnO thin film transistors (a-IGZO TFTs) processed at low temperature (150 °C) by using scalable vacuum deposition is proposed. This method entailed the quick injection of water vapor for 0.1 s and purge treatment in dry ambient in one cycle; the supply content of water vapor was simply controlled by the number of pulse repetitions. The electrical transport characteristics revealed a remarkable performance of the a-IGZO TFTs prepared at the maximum process temperature of 150 °C (field-effect mobility of 13.3 cm(2) V(-1) s(-1); Ion/Ioff ratio ≈ 10(8); reduced I-V hysteresis), comparable to that of a-IGZO TFTs annealed at 350 °C in dry ambient. Upon analysis of the angle-resolved x-ray photoelectron spectroscopy, the good performance was attributed to the effective suppression of the formation of hydroxide and oxygen-related defects. Finally, by using the wet pulse annealing process, we fabricated, on a plastic substrate, an ultrathin flexible a-IGZO TFT with good electrical and bending performances.

The effect of multivalent metal cations, including vanadium(V) and tin (Sn), on the electrical properties of vanadium-doped zinc tin oxide (VZTO) was investigated in the context of the fabrication of thin-film transistors (TFTs) using a single VZTO film and VZTO/ZTO bilayer as channel layers. The single VZTO TFT did not show any response to the gate voltage (insulator-like behavior). On the other hand, the VZTO/ZTO bilayer TFT exhibited a typical TFT transfer characteristic (semiconducting behavior). X-ray photoelectron spectroscopy revealed that, in contrast to what is commonly true in many oxides, oxygen vacancies (V(O)) in VZTO did not provide a dominant contribution to the total carrier concentration, because the V(O) peak area in the single VZTO film was 5.4% and reduced to 4.5% in VZTO/ZTO bilayer. Instead, Sn 3d5/2 and V 2p3/2 spectra suggest that the significant reduction in Sn and V ions is strongly related to the insulator-like behavior of the VZTO film. In negative-bias illumination tests and illumination tests with various photon energies, the VZTO/ZTO bilayer TFT had much better stability than the ZTO TFT. This result is attributed to the reduction of donor-like states ([Formula: see text]O) that can be positively ionized by blue and green illumination.

While tin oxides such as SnO and SnO2 are widely used in various applications, surprisingly, only a limited number of reports have been presented on the microstructural characteristics of tin oxide thin films grown under various growth conditions. In this paper, the effects of the substrate temperature and content of foreign Zn ion on the microstructural characteristics of tin oxide thin films grown by radio-frequency magnetron sputtering were investigated. The increase in substrate temperature induced change in the stoichiometry of the thin films from SnO(1+x) to SnO(2-x). Additionally, the phase contrast in the transmission electron microscopy image revealed that SnO(1+x) and SnO(2-x) phases were alternating in thin films and the width of each phase became narrower at high substrate temperature. The ternary zinc tin oxide thin films were deposited using the co-sputtering method. As the ZnO target power increased, the crystallinity of the thin films became poly-crystalline, and then showed improved crystallinity again with two types of phases.

An experiment was done to determine the efficacy of waste bottom ash as an effective microbial carrier. Bottom ash found to be a suitable microbial carrier. The average of viable cells of Paenibacillus polymyxa GS01 (as a test biocontrol agent) in bottom ash samples was about 10(8) cfu/10 ± 2 mg. The surface of bottom ash coated with 5% PVA w/v was most effective for improvement of cell viability. TSB medium containing 50 mg/L of MnSO(4) · H(2)O was the best for spore production of P. polymyxa GS01. Thus waste bottom ash coating with 5% PVA is likely to be suitable for use as a microbial carrier.

Balloon flower (Platycodon grandiflorum) is widely cultivated vegetable and used as a remedy for asthma in East Asia. Experiments were conducted to isolate endophytic bacteria from 1-, 3-, and 6-year-old balloon flower roots and to analyze the enzymatic, antifungal, and anti-human pathogenic activities of the potential endophytic biocontrol agents obtained. Total 120 bacterial colonies were isolated from the interior of all balloon flower roots samples. Phylogenetic analysis based on 16S rRNA gene sequences showed that the population of 'low G + C gram-positive bacteria' (LGCGPB) gradually increased 60.0-80.0% from 1 to 6 years balloon flower sample. On the other hand, maximum hydrolytic enzyme activity showing endophytic bacteria was under LGCGPB, among the bacterial strains, Bacillus sp. (BF1-1 and BF3-8), Bacillus sp. (BF1-2 and BF3-5), and Bacillus sp. (BF1-3, BF3-6, and BF6-4) showed maximum enzyme activities. Besides, Bacillus licheniformis (BF3-5 and BF6-6) and Bacillus pumilus (BF6-1) showed maximum antifungal activity against Phytophthora capsici, Fusarium oxysporum, Rhizoctonia solani, and Pythium ultimum. Moreover, Bacillus licheniformis was found in 3 and 6 years balloon flower roots, but Bacillus pumilus was found only in 6 years sample. It is presumed that older balloon flower plants invite more potential antifungal endophytes for there protection from plant diseases. In addition, Bacillus sp. (BF1-2 and BF3-5) showed maximum anti-human pathogenic activity. So, plant age is presumed to influence diversity of balloon flower endophytic bacteria.

3,5,6-trichloro-2-pyridinol (TCP) is a major metabolite of the insecticide chlorpyrifos and is hazardous to human and animal health. A gene encoding a TCP degrading enzyme was cloned from a metagenomic library prepared from cow rumen. The gene (tcp3A) is 2.5 kb in length, encoding a protein (Tcp3A) of 599 amino acid residues. Tcp3A has a potential signal sequence, as well as a putative ATP/GTP binding site, and a likely amidation site. The molecular weight of the enzyme is 62 kDa by SDS-PAGE. Comparison of Tcp3A with the NCBI database using BLASTP revealed homology to amidohydrolase proteins. Recombinant Escherichia coli harboring the tcp3A gene could utilize TCP as the sole source of carbon. TLC and HPLC revealed that TCP was degraded by recombinant E. coli harboring tcp3A. This is the first report of a gene encoding a TCP degrading enzyme.

Metagenomic analyses were conducted to evaluate the biodiversity of oyster shell bacteria, under storage conditions, on the basis of 16s rDNA sequences. Temperature was recorded during a one year storage period, and the highest temperature (about 60 degrees C) was observed after five months ofstorage. Bacterial diversity was greatest in the initial stage sample, with 33 different phylotypes classified under seven phyla (Proteobacteria, Bacteroidetes, Firmicutes, Actinobacteria, Planctomycetes, Verrucomicrobia and unclassified bacteria), with 42.22% ofphylotypes belonging to Proteobacteria. The lowest diversity was found in the high temperature (fermentation) stage sample, with 10 different phylotypes belonging to Firmicutes (78.57%) and Bacteroidetes. In the final stage sample, bacteria were found belonging to Proteobacteria, Bacteroidetes, and Firmicutes, and some were unclassified bacteria. Of the bacteria constituting the final stage metagenome, 69.70% belonged to Firmicutes. Our results show that bacteria belonging to phylum Firmicutes were predominant during fermentation, and during the final stages of oyster shell storage, which suggests that these bacteria supposed to be the key players for oyster shell biodegradation.

Lactobacillus brevis WCP902 that is capable of biodegrading chlorpyrifos was isolated from kimchi. The opdB gene cloned from this strain revealed 825 bp, encoding 274 aa, and an enzyme molecular weight of about 27 kDa. OpdB contains the same Gly-X-Ser-X-Gly motif found in most bacterial and eukaryotic esterase, lipase, and serine hydrolases, yet it is a novel member of the GDSVG family of esterolytic enzymes. Its conserved serine residue, Ser82, is significantly involved with enzyme activity that may have application for removing some pesticides. Optimum organophosphorus hydrolase (OpdB) activity appeared at pH 6.0 and 35 degrees C and during degradation of chlorpyrifos, coumaphos, diazinon, methylparathion, and parathion.

Bacillus licheniformis CBFOS-03 is a chitinase producing bacteria isolated from oyster (Crassostrea gigas) shell waste. We have cloned and expressed the chi18B gene of B. licheniformis CBFOS-03, which encodes a glycohydrolase family 18 chitinase (GH18). Chi18B is a predicted 598 amino acid protein that consists of a catalytic domain (GH18), a fibronectin type III domain (Fn3), and a chitin binding domain (CBD). Purified Chi18B showed optimum chitinase activity at pH 9 and 55 degrees C, and activity was stimulated with 25 mM Mn2+. In kinetic analysis, Chi18B showed Km values of 9.07 +/- 0.65 microM and 129.27 +/- 0.38 microM with the substrates 4-methylumbelliferyl-N-N'-diacetylchitobiose and alpha-chitin, respectively. Studies of C-terminal deletion constructs revealed that the GH18 domain with one amino acid in C-terminal region was sufficient for chitinase activity; however, fusions of full length and CBD-deleted constructs to green florescent protein (GFP) and yellow florescent protein (YFP) suggest that the C-terminus is supposedly important in binding to shell powder. Full length Chi18B with GFP showed green fluorescence with oyster shell powder, but GH18+Fn3 with GFP did not. Similarly, full length Chi18B with YFP showed yellow fluorescence with clam (Chamelea gallina) shell and disk abalone (Haliotis discus) shell powder, but GH18+Fn3 with YFP construct did not. So, the CBD domain of Chi18B appears to play an important role in binding of oyster and other marine shells. It is likely to be used as a probe to identify the presence of chitin in marine shells like oyster shell, clam shell, and disk abalone shell using fusions of Chi18B with fluorescent proteins.

We developed a multiplex PCR assay for the detection of lactic acid bacteria (LAB) species, and used it to examine the LAB species involved in kimchi fermentation. The LAB profile during kimchi fermentation varied with pH and acidity. Leuconostoc mesenteroides was observed during early fermentation (pH 5.64-4.27 and acidity 0.48-0.89%), and Lactobacillus sakei become dominant later in fermentation (pH or=0.98%). The efficiency of the multiplex PCR ranged from 86.5% at day 0 (pH 6.17 and acidity 0.24%) to 100% at day 96 (pH 4.16 and acidity 1.14). This multiplex PCR assay will facilitate study of the microbial ecosystem of kimchi and its impact on kimchi fermentation.

We examined the role of microorganisms in the degradation of the organophosphorus (OP) insecticide chlorpyrifos (CP) during kimchi fermentation. During the fermentation of kimchi, 30 mg L(-1) of CP was added and its stability assayed during fermentation. CP was degraded rapidly until day 3 (83.3%) and degraded completely by day 9. Four CP-degrading lactic acid bacteria (LAB) were isolated from kimchi fermentation in the presence of 200 mg L(-1) CP and were identified as Leuconostoc mesenteroides WCP907, Lactobacillus brevis WCP902, Lactobacillus plantarum WCP931, and Lactobacillus sakei WCP904. CP could be utilized by these four strains as the sole source of carbon and phosphorus. Coumaphos (CM), diazinon (DZ), parathion (PT), and methylparathion (MPT) were also degraded by WCP907, WCP902, WCP931, and WCP904 when provided as sole sources of carbon and phosphorus.

Bacterial diversity and the composition of individual communities during the composting process of swine and mushroom cultural wastes in a field-scale composter (Hazaka system) were examined using a PCR-based approach. The composting process was divided into six stages based on recorded temperature changes. Phylogenetic analysis of eighty 16S rRNA sequences from uncultured composting bacterial groups revealed the presence of representatives from three divisions, including plant pathogenic bacteria, high-molecule-degrading bacteria and spore-forming bacteria. The plant pathogen A. tumefaciens gradually decreased in abundance during the composting process and eventually disappeared during the thermophilic and cooling stage. A bacterium homologous to Bacillus humi first appeared at the early thermophilic stage and was established at the intermediate thermophilic, post-thermophilic, and cooling stages. It was not possible to isolate the B. humi during any of the stages using general culture techniques.