Search

In this research, we present an innovative, environmentally friendly, and cost-effective alcohothermal method for synthesizing Mn2+ and Mn2+–Cu+ doped 0D Cs3ZnCl5, a green luminescent material, marking the first time this approach has been reported. An exhaustive analysis of the luminescence properties of both undoped and doped Cs3ZnCl5 was conducted, with a particular emphasis on the energy transfer mechanisms in the Mn2+ mono-doped and Mn2+–Cu+ co-doped systems. The results demonstrate the successful construction of an efficient energy transfer pathway that significantly enhances the luminescence efficiency of Cs3ZnCl5:Mn2+. Specifically, the photoluminescence quantum yield of Mn2+ within the Cs3ZnCl5 matrix has been improved from 51.6% to 71.1%, thanks to the Cu+ codopant acting as an effective energy transfer mediator. A mechanism for the luminescence and energy transfer phenomena observed in the Mn2+–Cu+ co-doped Cs3ZnCl5 system has been also proposed. Furthermore, to assess the practical applicability of the synthesized materials, their structural and photoluminescent stability were evaluated. In essence, our study presents a promising solution to current challenges in the synthesis of advanced luminescent materials and opens up new possibilities for harnessing the potential of Mn2+-activated 0D metal halides in optoelectronic applications. [ABSTRACT FROM AUTHOR]

Tracking the trajectory of hydrogen intermediates during hydrogen electro‐catalysis is beneficial for designing synergetic multi‐component catalysts with division of chemical labor. Herein, we demonstrate a novel dynamic lattice hydrogen (LH) migration mechanism that leads to two orders of magnitude increase in the alkaline hydrogen oxidation reaction (HOR) activity on Pd@Pt over pure Pd, even ≈31.8 times mass activity enhancement than commercial Pt. Specifically, the polarization‐driven electrochemical hydrogenation process from Pd@Pt to PdHx@Pt by incorporating LH allows more surface vacancy Pt sites to increase the surface H coverage. The inverse dehydrogenation process makes PdHx as an H reservoir, providing LH migrates to the surface of Pt and participates in the HOR. Meanwhile, the formation of PdHx induces electronic effect, lowering the energy barrier of rate‐determining Volmer step, thus resulting in the HOR kinetics on Pd@Pt being proportional to the LH concentration in the in situ formed PdHx@Pt. Moreover, this dynamic catalysis mechanism would open up the catalysts scope for hydrogen electro‐catalysis. [ABSTRACT FROM AUTHOR]

Water electrolysis for H2 production is restricted by the sluggish oxygen evolution reaction (OER). Using the thermodynamically more favorable hydrazine oxidation reaction (HzOR) to replace OER has attracted ever‐growing attention. Herein, we report a twisted NiCoP nanowire array immobilized with Ru single atoms (Ru1−NiCoP) as superior bifunctional electrocatalyst toward both HzOR and hydrogen evolution reaction (HER), realizing an ultralow working potential of −60 mV and overpotential of 32 mV for a current density of 10 mA cm−2, respectively. Inspiringly, two‐electrode electrolyzer based on overall hydrazine splitting (OHzS) demonstrates outstanding activity with a record‐high current density of 522 mA cm−2 at cell voltage of 0.3 V. DFT calculations elucidate the cooperative Ni(Co)−Ru−P sites in Ru1−NiCoP optimize H* adsorption, and enhance adsorption of *N2H2 to significantly lower the energy barrier for hydrazine dehydrogenation. Moreover, a self‐powered H2 production system utilizing OHzS device driven by direct hydrazine fuel cell (DHzFC) achieve a satisfactory rate of 24.0 mol h−1 m−2. [ABSTRACT FROM AUTHOR]

Creating high‐speed soft actuators will have broad engineering and technological applications. Snapping provides a power‐amplified mechanism to achieve rapid movements in soft actuators that typically show slow movements. However, precise control of snapping dynamics (e.g., speed and direction of launching or jumping) remains a daunting challenge. Here, a bioinspired design principle is presented that harnesses a reconfigurable constraint structure integrated into a photoactive liquid crystal elastomer actuator to enable tunable and programmable control over its snapping dynamics. By reconfiguring constrained fin‐array‐shaped structure, the snapping dynamics of the structured actuator, such as launching or jumping angle and height, motion speed, and release force can be on‐demand tuned, thus enabling controllable catapult motion and programmable jumping. Moreover, the structured actuators exhibit a unique combination of ultrafast moving speed (up to 2.5 m s−1 in launching and 0.22 m s−1 in jumping), powerful ejection (long ejection distance of ≈20 cm, 35 mg ball), and high jumping height (≈8 cm, 40 times body lengths), which few other soft actuators can achieve. This study provides a new universal design paradigm for realizing controllable rapid movements and high‐power motions in soft matter, which are useful for building high‐performance soft robotics and actuation devices. [ABSTRACT FROM AUTHOR]