Search

Among the family of two-dimensional materials, the emerging MXenes materials have gained widespread popularity due to the unique properties such as ultra-thin structure, good electrical conductivity, tunable surface functionality, and excellent photothermal conversion. Improvement of a range of desalination materials with MXenes has led to the widespread application in the field of desalination. The aim of this paper is to review the recent developments in a range of desalination strategies using MXenes, and to discuss in detail the application and development of MXenes materials in the fields of capacitive deionization, solar interfacial evaporation, and pervaporation desalination. The excellent desalination capabilities of MXenes could provide a solution to the current growing freshwater crisis.

In recent years, the variability in the composition of cement raw materials has increasingly impacted the quality of cement products. However, there has been relatively little research on the homogenization effects of equipment in the cement production process. Existing studies mainly focus on the primary functions of equipment, such as the grinding efficiency of ball mills, the thermal decomposition in cyclone preheaters, and the thermal decomposition in rotary kilns. This study selected four typical pieces of equipment with significant homogenization functions for an in-depth investigation: ball mills, pneumatic homogenizing silos, cyclone preheaters, and rotary kilns. To assess the homogenization efficacy of each apparatus, scaled-down models of these devices were constructed and subjected to simulated experiments. To improve experimental efficiency and realistically simulate actual production conditions in a laboratory setting, this study used the uniformity of the electrical capacitance of mixed powders instead of compositional uniformity to analyze homogenization effects. The test material in the experiment consisted of a mixture of raw meal from a cement factory with a high dielectric constant and Fe3O4 powder. The parallel plate capacitance method was employed to ascertain the capacitance value of the mixed powder prior to and subsequent to treatment by each equipment model. The fluctuation of the input and output curves was analyzed, and the standard deviation (S), coefficient of variation (R), and homogenization multiplier (H) were calculated in order to evaluate the homogenization effect of each equipment model on the raw meal. The findings of the study indicated that the pneumatic homogenizer exhibited an exemplary homogenization effect, followed by the ball mill. For the ball mill, a higher proportion of small balls in the gradation can significantly enhance the homogenization effect without considering the grinding efficiency. The five-stage cyclone preheater also has a better homogenization effect, while the rotary kiln has a less significant homogenization effect on raw meal. Finally, the raw meal processed by each equipment model was used for clinker calcination and the preparation of cement mortar samples. After curing for three days, the compressive and flexural strengths of the samples were tested, thereby indirectly verifying the homogenization effect of each equipment model on the raw meal. This study helps to understand the homogenization process of raw materials by equipment in cement production and provides certain reference and data support for equipment selection, operation optimization, and quality control in the cement production process. [ABSTRACT FROM AUTHOR]

During industrial and laboratory processes involving material grinding, the grinding media endure prolonged high-collision and friction environments, resulting in substantial wear. Consequently, this study adopts the hot-pressing sintering technique in powder metallurgy to prepare SiC-reinforced Fe-based wear-resistant composite grinding media, aiming to increase wear performance. For this purpose, Fe with 10 wt% SiC powders were milled for the fabrication of the composite. Then, sintering was performed by hot press at 1100 °C in a furnace. Scanning electron microscopy (SEM) and X-ray diffraction were employed to investigate the microstructures and phase of SiC-reinforced Fe-based matrix composite. Subsequently, comparative performance evaluations of the newly developed grinding media and traditional chromium-based media were conducted in terms of wear rate and grinding efficiency. The wear resistance tests revealed that the SiC-reinforced composite media displayed significantly superior wear resistance across various abrasives compared to the chromium-containing alternatives. Specifically, the composite media achieved a wear rate reduction of 2.9 times against standard sand over 1 h, and 2.3 and 2.4 times against sandstone and iron slag, respectively. Moreover, extended grinding for 3 hours further enhanced these reductions to 3.1, 2.4, and 2.7 times, respectively. Additionally, efficiency assessments indicated that at a 1:1 material ratio, the composite media outperformed the chromium-containing media in grinding efficiency by 7.5%, 12.5%, and 10.3% for standard sand, sandstone, and iron slag, respectively. Further increasing the material ratio to 3:1 resulted in efficiency improvements of 7.4%, 17.5%, and 11.3%, correspondingly. [ABSTRACT FROM AUTHOR]

Copper-containing sludge is a common by-product of industrial activities, particularly electroplating and metal processing. This type of sludge contains high concentrations of heavy metals such as copper, which can pose a potential threat to the environment. Therefore, its treatment and disposal require special attention. Due to its efficient mass and heat transfer characteristics, the suspended state technology has shown significant potential for application in a number of key processes, including the drying, decomposition, and reduction of copper-containing sludge. This paper presents an in-depth analysis of the current status of the application of the suspended state technology in the treatment of copper-containing sludge. Based on this analysis, a device for the treatment of copper-containing sludge in the suspended state was designed, through which the characteristics of copper-containing sludge in the oxidative decomposition and reduction phases are investigated. The research objects were gas concentration, temperature, contact state, and particle size time. Orthogonal experiments were initially employed to investigate the relationship between the influencing factors and the conversion rate of copper oxides. This was followed by a single-factor influence study, which led to the determination of the optimal process parameters for the decomposition experiments of the Cu-containing sludge in an oxidizing atmosphere. The 100 μm Cu-containing sludge was reacted with 10% O2 gas at a flow rate of 1 m/s for 3 min under the condition of 900 °C. The process parameters were then determined as follows: The research objects were gas concentration, temperature, contact state, and particle size time. Orthogonal experiments were employed to investigate the relationship between the influencing factors and the copper conversion rate. This was followed by a single-factor influence study, which determined the optimal process parameters for the copper-containing sludge reduction experiments. The 200 μm copper-containing sludge was reacted for 5 min at a flow rate of 7% carbon monoxide at a flow rate of 1.5 m/s under the condition of 800 °C. [ABSTRACT FROM AUTHOR]

The emerging applications of hydrogels in flexible devices require it possess multifunctional properties including stable mechanical and functions under various deformations or external environments. Herein, a multifunctional polyvinyl alcohol/M-alginate/PAM hydrogel with very excellent mechanical properties and sensing functions was fabricated by introducing multiple pairs of toughing mechanisms into triple network (TN). The multiple supramolecular physical networks work as sacrificial networks to toughen the materials when hydrogel deforms. The broken bonds can reform upon unloading endowing the recovery of hydrogels' properties and functions with the assistance of the elastic covalent network. The optimal TN hydrogels are extremely tough (a fracture strength of 512 kPa, a fracture toughness of 3 M J/[m.sup.3]) and recoverable from fatigue damage (~77% toughness recovery after 5 min resting at room temperature). The presence of abundant ionic species endows the tough and recoverable TN hydrogels high ionic conductivity and high sensitivity as strain sensors. Moreover, such TN hydrogels with multi-bond crosslinking in three networks can potentially guarantee stable mechanical and sensor functions under various deformations or external environments compared to the DN candidates. This work provides a simple strategy for fabricating multifunctional hydrogels with high stability to fulfill its flexible devices applications., INTRODUCTION Ionic conductive hydrogels with polymer networks swollen with electrolyte solutions have been explored for applications in flexible devices, including ionic skin sensors and hydrogel-based electrolytes for energy storage devices [...]

Traditional liquid phase methods for growing single crystals are static growth methods, which include seed crystal sedimentation growth and seed crystal clamping growth using seed crystal holders. Single crystals grown via seed crystal sedimentation often have a flat and elongated shape, and the region in contact with the bottom of the container is restricted during growth, resulting in significant defects. Similarly, the seed crystal clamping growth method cannot avoid contact with external objects, leading to abnormal growth at the contact points and along the direction of the seed crystal holder, also resulting in certain defects. Both of these growth methods require processes, such as cutting and grinding, to remove defects, resulting in resource waste. To address the shortcomings of the static liquid phase single-crystal preparation mentioned above, this study successfully designed a dynamic liquid phase method for single crystal growth, which achieved the successful suspension of seed crystals in the mother solution and the growth of high-quality, large-sized single crystals, avoiding contact with the walls and the bottom of the container during the crystal growth process. Based on the dynamic liquid phase single crystal growth apparatus mentioned above, stable and dynamic liquid phase preparation was successfully achieved, ranging from seed crystals with a diameter of approximately 5 mm to single crystals with a diameter of approximately 20 mm, by controlling the cooling rate and adjusting the solution flow rate. [ABSTRACT FROM AUTHOR]