Search

Methane detection limits, emission rate quantification accuracy, and potential cross-species interference are assessed for Bridger Photonics’ Gas Mapping LiDAR (GML) system utilizing data collected during laboratory testing and single-blind controlled release testing. Laboratory testing identified no significant interference in the path-integrated methane measurement from the gas species tested (ethylene, ethane, propane, n-butane, i-butane, and carbon dioxide). The controlled release study, comprised of 650 individual measurement passes, represents the largest dataset collected to date to characterize GML with respect to point-source emissions. Binomial regression is utilized to create detection curves illustrating the likelihood of detecting an emission of a given size under different wind conditions and for different flight altitudes. Wind-normalized methane detection limits (90% detection rate) of 0.25 (kg/h)/(m/s) and 0.41 (kg/h)/(m/s) are observed at a flight altitude of 500 feet and 675 feet above ground level, respectively. Quantification accuracy is also assessed for emissions ranging from 0.15 to 1,400 kg/h. When emission rate estimates were generated using wind from high-resolution rapid refresh (HRRR) model (the primary wind source that Bridger uses for their commercial operations), linear regression indicates bias of 8.1% (R2 = 0.89). For 95% of controlled releases above Bridger’s stated production-sector detection sensitivity (3 kg/h with 90% probability of detection), the accuracy of individual emission rate estimates produced using HRRR wind ranged from −64.1% to +87.0%. Across all controlled releases, 38.1% of estimates had error within ±20%, and 87.3% of measurements were within a factor of two (−50% to +100% error). At low wind speed (less than 2 m/s) and low emission rates (less than 3 kg/h), emission estimates are biased high, however when removed do not impact the regression significantly. The aggregate quantification error including all detected emission events was +8.2% using the HRRR wind source. The resulting detection curves and quantification accuracy illustrate important implications that must be considered when using measurements from GML or other remote emission measurement techniques to inform or validate inventory models or to audit reported emission levels from oil and gas systems.

Advances in power electronics and their use in Miscellaneous Electric Loads (MELs) in buildings have resulted in increased interest in using low-voltage direct current (DC) power distribution as a replacement for the standard alternating current (AC) power distribution in buildings. Both systems require an endpoint converter to convert the distribution system voltage to the MELs voltage requirements. This study focused on the efficiency of these endpoint converters by testing pairs of AC/DC and DC/DC power converters powering the same load profile. In contrast to prior studies, which estimated losses based on data sheet efficiency and rated loads, in this study, we used part load data derived from real-world time-series load measurements of MELs and experimentally characterized efficiency curves for all converters. The measurements performed for this study showed no systematic efficiency advantage for commercially available DC/DC endpoint converters relative to comparable, commercially available AC/DC endpoint converters. For the eight appliances analyzed with the pair of converters tested, in 50%, the weighted energy efficiency of the DC/DC converter was higher, while, for the other 50%, the AC/DC converter was. Additionally, the measurements indicated that the common assumption of using either data sheet efficiency values or efficiency at full load may result in substantial mis-estimates of the system efficiency.

Quantifying methane emissions is essential for meeting near-term climate goals and is typically carried out using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas production sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings, resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer's average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm, with maximum values of 117.5 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios shows overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML-derived metal oxide sensors' mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher priced trace methane analyzers. This would improve confidence in low-cost sensors' response, reduce the cost of sensor deployment, and allow for timely and accurate tracking of methane emissions. [ABSTRACT FROM AUTHOR]

Methane is a powerful greenhouse gas with a 25 times higher 100-year warming potential than carbon dioxide and is a target for mitigation to achieve climate goals. To control and curb methane emissions, estimates are required from the sources and sectors which are typically generated using bottom-up methods. However, recent studies have shown that national and international bottom-up approaches can significantly underestimate emissions. In this study, we present three bottom-up approaches used to estimate methane emissions from all emission sectors in the Denver-Julesburg basin, CO, USA. Our data show emissions generated from all three methods are lower than historic measurements. A Tier 1/2 approach using IPCC emission factors estimated 2022 methane emissions of 358 Gg (0.8% of produced methane lost by the energy sector), while a Tier 3 EPA-based approach estimated emissions of 269 Gg (0.2%). Using emission factors informed by contemporary and region-specific measurement studies, emissions of 212 Gg (0.2%) were calculated. The largest difference in emissions estimates were a result of using the Mechanistic Air Emissions Simulator (MAES) for the production and transport of oil and gas in the DJ basin. The MAES accounts for changes to regulatory practice in the DJ basin, which include comprehensive requirements for compressors, pneumatics, equipment leaks, and fugitive emissions, which were implemented to reduce emissions starting in 2014. The measurement revealed that normalized gas loss is predicted to have been reduced by a factor of 20 when compared to 10-year-old normalization loss measurements and a factor of 10 less than a nearby oil and production area (Delaware basin, TX); however, we suggest that more measurements should be made to ensure that the long-tail emission distribution has been captured by the modeling. This study suggests that regulations implemented by the Colorado Department of Public Health and Environment could have reduced emissions by a factor of 20, but contemporary regional measurements should be made to ensure these bottom-up calculations are realistic. [ABSTRACT FROM AUTHOR]

Quantitative optical gas imaging (QOGI) system can rapidly quantify leaks detected by optical gas imaging (OGI) cameras across the oil and gas supply chain. A comprehensive evaluation of the QOGI system's quantification capability is needed for the successful adoption of the technology. This study conducted single-blind experiments to examine the quantification performance of the FLIR QL320 QOGI system under near-field conditions at a pseudo-realistic, outdoor, controlled testing facility that mimics upstream and midstream natural gas operations. The study completed 357 individual measurements across 26 controlled releases and 71 camera positions for release rates between 0.1 kg C h 4 / h and 2.9 kg C h 4 / h of compressed natural gas (which accounts for more than 90% of typical component-level leaks in several production facilities). The majority (75%) of measurements were within a quantification factor of 3 (quantification error of −67% to 200%) with individual errors between −90% and 831%, which reduced to −79% to +297% when the mean of estimates of the same controlled release from multiple camera positions was considered. Performance improved with increasing release rate, using clear sky as plume background, and at wind speeds ≤1 mph relative to other measurement conditions. [ABSTRACT FROM AUTHOR]