Search

There is a steady trend in the world to increase the share of distributed generation. The volume of self-generated energy commissioning is constantly growing, with projected increases in growth rates in the future. At the same time, demands for efficiency and environmental safety in new power plants are constantly increasing. In this regard, one of the promising areas for the development of distributed energy is the transition to small nuclear power plants (SNPPs). As in the case of wind and solar power plants, SNPP operations are not accompanied by emissions of toxic substances or greenhouse gases into the atmosphere. In addition, SNPPs consume a much smaller volume and mass of fuel compared to conventional small-capacity fossil fuel power plants. This paper describes the characteristics of the main types of distributed generation. The key technical and economic characteristics of existing and prospective small-capacity nuclear fuel facilities are systematized. The results of a comparative analysis of the cost of electricity produced by SNPPs and competing power plants are also presented. In addition, a number of promising regions of the Russian Federation for the introduction of SNPPS have been identified, and a review of the methods of energy storage for SNPPS, which are necessary when working in an isolated power system, has been carried out. [ABSTRACT FROM AUTHOR]

Today, with the increases in organic fuel prices and growing legislative restrictions aimed at increasing environmental safety and reducing our carbon footprint, the task of increasing thermal power plant efficiency is becoming more and more topical. Transforming combusting fuel thermal energy into electric power more efficiently will allow the reduction of the fuel cost fraction in the cost structure and decrease harmful emissions, especially greenhouse gases, as less fuel will be consumed. There are traditional ways of improving thermal power plant energy efficiency: increasing turbine inlet temperature and utilizing exhaust heat. An alternative way to improve energy efficiency is the use of supercritical CO2 power cycles, which have a number of advantages over traditional ones due to carbon dioxide's thermophysical properties. In particular, the use of carbon dioxide allows increasing efficiency by reducing compression and friction losses in the wheel spaces of the turbines; in addition, it is known that CO2 turbomachinery has smaller dimensions compared to traditional steam and gas turbines of similar capacity. Furthermore, semi-closed oxy–fuel combustion power cycles can reduce greenhouse gases emissions by many times; at the same time, they have characteristics of efficiency and specific capital costs comparable with traditional cycles. Given the high volatility of fuel prices, as well as the rising prices of carbon dioxide emission allowances, changes in efficiency, capital costs and specific greenhouse gas emissions can lead to a change in the cost of electricity generation. In this paper, key closed and semi-closed supercritical CO2 combustion power cycles and their promising modifications are considered from the point of view of energy, economic and environmental efficiency; the cycles that are optimal in terms of technical and economic characteristics are identified among those considered. [ABSTRACT FROM AUTHOR]

The atmosphere carbon dioxide content grows subsequently due to anthropogenic factors. It may be considerably mitigated by the development of thermal power plants with near zero emissions. A promising way is the transition to the semi-closed oxy-fuel combustion power cycles with carbon dioxide and water vapor mixture as a working fluid. However, their wide implementation requires reduction of the metal consumption for the highly efficient regeneration system. This paper discloses the results of feasibility study for the regeneration system of the prospective oxy-fuel combustion power plant. The effect of operating parameters on the cycle energy efficiency, overall dimensions, and the cost of the regenerator was determined. Underheating increase in the regenerator by 1 °C leads to the net efficiency factor drop of the oxy-fuel combustion power cycle by 0.13% at average and increases fuel costs by 0.28%. Increase of pressure drop in the hot channel by 1% leads to efficiency drop by 0.14%. The optimum set of design and operating parameters of the feed heating system has been determined, which ensures the best technical and economic indicators of electrical power generation: the minimum cumulative costs are achieved when underheating in the regenerator is 20 °C and pressure drop in the hot channel is 4%, under the use of S-shaped fins channels. [ABSTRACT FROM AUTHOR]

Copyright of Transformations in Business & Economics is the property of Vilnius University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Transformations in Business & Economics is the property of Vilnius University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The Rankine cycle is widely used for electricity production. Significant weight and size characteristics of the power equipment working on superheated steam are the main disadvantages of such power plants. The transition to supercritical carbon dioxide (S-CO2) working fluid is a promising way to achieve a significant reduction in equipment metal consumption and to increase energy efficiency. This paper presents the results of thermodynamic analysis of S-CO2 thermal power plants (TPPs) utilizing the heat of combustion products of an energy boiler. It was found that the net efficiency of the developed S-CO2 TPP with a pulverized coal-fired boiler reached 49.2% at an initial temperature of 780 °C, which was 2% higher compared to the efficiency level of steam turbine power plants (STPPs) at a similar turbine inlet temperature. [ABSTRACT FROM AUTHOR]

The transition to the use of supercritical carbon dioxide as a working fluid for power generation units will significantly reduce the equipment′s overall dimensions while increasing fuel efficiency and environmental safety. Structural and parametric optimization of S–CO2 nuclear power plants was carried out to ensure the maximum efficiency of electricity production. Based on the results of mathematical modeling, it was found that the transition to a carbon dioxide working fluid for the nuclear power plant with the BREST–OD–300 reactor leads to an increase of efficiency from 39.8 to 43.1%. Nuclear power plant transition from the Rankine water cycle to the carbon dioxide Brayton cycle with recompression is reasonable at a working fluid temperature above 455 °C due to the carbon dioxide cycle′s more effective regeneration system. [ABSTRACT FROM AUTHOR]

The transition to oxy-fuel combustion power cycles is a prospective way to decrease carbon dioxide emissions into the atmosphere from the energy sector. To identify which technology has the highest efficiency and the lowest emission level, a thermodynamic analysis of the semiclosed oxy-fuel combustion combined cycle (SCOC-CC), the E-MATIANT cycle, and the Allam cycle was carried out. The modeling methodology has been described in detail, including the approaches to defining the working fluid properties, the mathematical models of the air separation unit, and the cooled gas turbine cycles' calculation algorithms. The gas turbine inlet parameters were optimized using the developed modeling methodology for the three oxy-fuel combustion power cycles with CO2 recirculation in the inlet temperature at a range of 1000 to 1700 °C. The effect of the coolant flow precooling was evaluated. It was found that a decrease in the coolant temperature could lead to an increase of the net efficiency up to 3.2% for the SCOC-CC cycle and up to 0.8% for the E-MATIANT cycle. The final comparison showed that the Allam cycle's net efficiency is 5.6% higher compared to the SCOC-CC cycle, and 11.5% higher compared with the E-MATIANT cycle. [ABSTRACT FROM AUTHOR]

Recent climate changes stimulate the search and introduction of solutions for the reduction of the anthropogenic effect upon the environment. Transition to the oxy-fuel combustion power cycles is an advanced method of CO2 emission reduction. In these energy units, the main fuel is natural gas but the cycles may also work on syngas produced by the solid fuel gasification process. This paper discloses a new highly efficient oxy-fuel combustion power cycle with coal gasification, which utilizes the syngas heat in two additional nitrogen gas turbine units. The cycle mathematics simulation and optimization result with the energy unit net efficiency of 40.43%. Parametric studies of the cycle show influence of the parameters upon the energy unit net efficiency. Change of the cycle fuel from natural gas to coal is followed by a nearly twice increase of the carbon dioxide emission from 4.63 to 9.92 gmCO2/kWh. [ABSTRACT FROM AUTHOR]

The Rankine cycle steam turbine power plants make a base for world electricity production. The efficiency of modern steam turbine units is not higher than 43-45%, which is remarkably lower compared to the combined cycle power plants. However, an increase in steam turbine power plant efficiency could be achieved by the rise of initial cycle parameters up to ultra-supercritical values: 700-780°C, 30-35 MPa. A prospective steam superheating technology is the oxy-fuel combustion heating in a sidemounted combustor located in the steam pipelines. This paper reviews thermal schemes of steam turbine power plants with one or two side-mounted steam superheaters. An influence of the initial steam parameters on the facility thermal efficiency was identified and primary and secondary superheater parameters were optimized. It was found that the working fluid superheating in the side-mounted oxy-methane combustors leads to an increase of thermal efficiency higher than that with the traditional boiler superheating in the initial temperature ranges of 700-780°C and 660-780°C by 0.6% and 1.4%, respectively. [ABSTRACT FROM AUTHOR]

One of the problems in Russia Power Sector strategy until 2035 is the technologies development for mitigation of harmful emissions by the heat and power production industry. This goal may be reached by the transition to environmentally friendly generation units such as oxy-fuel combustion power cycles that burn organic fuels in pure oxygen. This paper provides the results of research on one of the most efficient oxy-fuel combustion power cycle, which was modified by the usage of nitrogen for turbine cooling. The computer simulation and parametric optimization approaches are described in detail. The net efficiency of the oxy-fuel combustion power cycle in relationship to the carbon dioxide turbine exhaust pressure is shown. Moreover, the influence of the regenerator scheme and modeling parameters on heat performance is obtained. Particularly, it was found that the transition to a scheme with five two-threaded heat exchangers decrease cycle efficiency by 4.2% compare to a scheme with a multi-stream regenerator. [ABSTRACT FROM AUTHOR]