Search

We review successes and challenges from five recent subglacial bedrock drilling campaigns intended to find evidence for Antarctic Ice Sheet retreat during warm periods in the geologic past. Insights into times when the polar ice sheets were smaller than present serve as guiding information for modeling efforts that aim to predict the rate and magnitude of future sea level rise that would accompany major retreat of the Antarctic Ice Sheet. One method to provide direct evidence for the timing of deglaciations and minimum extent of prior ice sheets is to extract subglacial bedrock cores for cosmogenic nuclide analysis from beneath the modern ice sheet surface. Here we summarize the lessons learned from five field seasons tasked with obtaining bedrock cores from shallow depths (

Diffuse optical spectroscopy (DOS) techniques characterize scattering media by examining their optical response to laser illumination. Time-domain DOS methods involve illuminating the medium with a laser pulse and using a fast photodetector to measure the time-dependent intensity of light that exits the medium after multiple scattering events. While DOS research traditionally focused on characterizing biological tissues, we demonstrate that time-domain diffuse optical measurements can also be used to characterize snow. We introduce a model that predicts the time-dependent reflectance of a dry snowpack as a function of its density, grain size, and black carbon content. We develop an algorithm that retrieves these properties from measurements at two wavelengths. To validate our approach, we assembled a two-wavelength lidar system to measure the time-dependent reflectance of snow samples with varying properties. Rather than measuring direct surface returns, our system captures photons that enter and exit the snow at different points, separated by a small distance (4–10 cm). We observe clear, linear correlations between our retrievals of density and black carbon concentration, and ground truth. For black carbon concentration the correlation is nearly one-to-one. We also find that our method is capable of distinguishing between small and large grain sizes.

We developed automated ablation stakes to measure colocated in situ changes in relative glacier-surface elevation and climatological drivers of ablation. The designs, refined over 10 years of development and deployments, implement open-source hardware and common building materials. The ablation stakes record distance to the snow/ice surface, air temperature and relative humidity every 1–15 min. Using these high-frequency data, we demonstrate that melt factors calculated using standard melt-rate vs temperature regressions converge over averaging windows of approximately 12 h or greater. Furthermore, we evaluate an integral approach to estimating temperature-index melt factors for ablation. In a test case on Glaciar Perito Moreno, Argentina, this integral approach reveals an overall positive-degree-day melt factor of 7.5 mm w.e. $^\circ$ C−1 d−1. We describe four deployments with iteratively improved designs and provide a list of materials required to construct an automated ablation stake. [ABSTRACT FROM AUTHOR]

The geodetic mass balance of a glacier corresponds to glacier-wide volume changes, converted to mass changes using density assumptions. It is typically calculated by differencing multi-temporal digital elevation models. In this study, we show how the annual geodetic mass balance of a glacier can be derived from uncrewed aerial vehicle (UAV) data. The presented workflow is applied to two small- to medium-sized glaciers in the Kyrgyz Tien Shan (Central Asia): Bordu glacier and Sary-Tor glacier. The obtained geodetic mass balance is compared with the glaciological mass balance derived from a network of ablation stakes and snow pits. A previously calibrated mass-balance model is used to correct for the difference in acquisition dates. The results show that the determined geodetic mass balance matches closely with the glaciological mass balance. Besides, for both glaciers the geodetic mass balance does not seem to be particularly sensitive to the assumptions regarding volume-to-mass conversion. Therefore, our results demonstrate that UAVs can serve as a valuable instrument to quantify the annual geodetic mass balance and to validate the glaciological mass balance. The conventional glaciological mass-balance estimation often relies on interpolation and extrapolation methods, whereas UAVs offer the potential for direct data acquisition over the entire glacier surface. [ABSTRACT FROM AUTHOR]

Progress in our understanding of wave–ice interactions is currently hindered by the lack of in situ observations and information of sea-ice properties, including the elastic modulus. Here, we estimate the effective elastic modulus of sea ice using observations of waves in ice through the deployment of three open-source geophone recorders on landfast sea ice. From observations of low-frequency dispersive waves, we obtain an estimate of the effective elastic modulus in the range of 0.4–0.7 GPa. This is lower than the purely elastic modulus of the ice estimated at 1 GPa as derived from in situ beam experiments. Importantly, our experimental observation is significantly lower than the default value currently in use in wave models. While our estimate is not representative for all sea ice, it does indicate that considerably more measurements are required to provide confidence in the development of parameterizations for this complex sea-ice property for wave models.

We present a method for tracking radio-tagged pebbles and cobbles through subglacial meltwater channels under shallow temperate glaciers. Natural particles tagged with active radio transmitters were injected directly into a large subglacial channel 300 m up-glacier from the terminus of the Glacier d'Otemma, Switzerland. A roving antenna was developed to localise tagged particles planimetrically in subglacial and proglacial channel reaches (350 and 150 m long, respectively) using a probabilistic technique, delivering records of the change in particle location and transport distance over time with uncertainty. The roving antenna had a ±5−15 m planimetric precision, a 75% particle localisation rate and operated at a maximum ice depth of 47 m. Additionally, stationary supraglacial and proglacial antennas continuously monitored the passage of tagged particles through consecutive reaches of the channel, constraining the timing of particle transport events. The proglacial antenna system had a 98.1% detection rate and was operational to 0.89 m water depth during testing. Roving and stationary antenna records were combined to create a transport distance model for each particle, which may be used in conjunction with hydraulic data to investigate the kinematics of particle motion. When applied at scale in future studies, this method may be used to reveal the mechanisms and timescales of coarse sediment export from Alpine glaciers.

We present seismic measurements of the firn column at Korff Ice Rise, West Antarctica, including measurements of compressional-wave velocity and attenuation. We describe a modified spectral-ratio method of measuring the seismic quality factor (Q) based on analysis of diving waves, which, combined with a stochastic method of error propagation, enables us to characterise the attenuative structure of firn in greater detail than has previously been possible. Q increases from 56 ± 23 in the uppermost 12 m to 570 ± 450 between 55 and 77 m depth. We corroborate our method with consistent measurements obtained via primary reflection, multiple, source ghost, and critically refracted waves. Using the primary reflection and its ghost, we find Q = 53 ± 20 in the uppermost 20 m of firn. From the critical refraction, we find Q = 640 ± 400 at 90 m depth. Our method aids the understanding of the seismic structure of firn and benefits characterisation of deeper glaciological targets, providing an alternative means of correcting seismic reflection amplitudes in cases where conventional methods of Q correction may be impossible.

Converting measurements of ice-sheet surface elevation change to mass change requires measurements of accumulation and knowledge of the evolution of the density profile in the firn. Most firn-densification models are tuned using measured depth–density profiles, a method which is based on an assumption that the density profile in the firn is invariant through time. Here we present continuous measurements of firn-compaction rates in 12 boreholes near the South Pole over a 2 year period. To our knowledge, these are the first continuous measurements of firn compaction on the Antarctic plateau. We use the data to derive a new firn-densification algorithm framed as a constitutive relationship. We also compare our measurements to compaction rates predicted by several existing firn-densification models. Results indicate that an activation energy of 60 kJ mol−1, a value within the range used by current models, best predicts the seasonal cycle in compaction rates on the Antarctic plateau. Our results suggest models can predict firn-compaction rates with at best 7% uncertainty and cumulative firn compaction on a 2 year timescale with at best 8% uncertainty.

Recent research has highlighted the potential for high-resolution, high-density, 3D and 4D ground-penetrating radar (GPR) acquisitions on alpine glaciers. When carried out on foot, such surveys are laborious and time consuming, which limits their application to small domains of limited glaciological interest. Further, crevasses and other hazards make the data acquisition risky. To address these issues, we have developed a drone-based GPR system. The system has a payload weight of 2.2 kg and a data output rate of 14 traces per second. An 80-MHz antenna and a recording time of 2800 ns mean that depths of over 100 m can be reached in temperate ice. Differential GPS positioning assures accurate flight paths. At a speed of 4 m s−1 and height of 5 m above the glacier surface, our system can acquire over 4 line-km of GPR data in 20 min on a single set of drone batteries. After presenting the technical specifications of the system and tests required to optimize its performance, we showcase a recently acquired 3D dataset from the Otemma glacier in Switzerland, where 462 parallel GPR profiles were surveyed at a 1-m line spacing, totaling over 112 line-km of data, in only 4 days.

To better constrain meltwater transport and ice viscosity in temperate glaciers, particularly in ice stream shear margins, we use a custom permeameter to study the untested model relationship between the permeability of temperate ice and its liquid water content. The permeability of lab-made ice of two mean grain diameters (1.8 and 4.2 mm) is measured, and water content is controlled with the ice salinity and measured calorimetrically. Fluorescein dye is added to through-flowing, chilled water to highlight flow pathways through the ice after experiments. As predicted by a simple model, permeability increases with approximately the square of the water content and by about three orders of magnitude across water contents of 0.1–4.4%. However, permeability values are less than those of the model by average factors of 2.6 and 4.1 for the finer and coarser ice, respectively. This discrepancy is likely due to tortuous, truncated or air-clogged veins. The order-of-magnitude agreement between measured and modeled values may indicate that reduced permeability from these factors is nearly compensated by preferential flow in oversized veins that are isolated or arborescent. Both kinds of preferred flow pathways are observed but the latter only in fine-grained ice at water contents > 2%.

A 198.8 m deep borehole was drilled through ice to subglacial bedrock in the northwestern marginal part of Princess Elizabeth Land, ~12 km south of Zhongshan Station, in January–February 2019. Three years later, in February 2022, the borehole temperature profile was measured, and the geothermal heat flow (GHF) was estimated using a 1-D time-dependent energy-balance equation. For a depth corresponding to the base of the ice sheet, the GHF was calculated as 72.6 ± 2.3 mW m−2 and temperature −4.53 ± 0.27°C. The regional averages estimated for this area based, generally, on tectonic setting vary from 55 to 66 mW m−2. A higher GHF is interpreted to originate mostly from the occurrence of metamorphic complexes intruded by heat-producing elements in the subglacial bedrock below the drill site.

Accurately quantifying all the components of the surface energy balance (SEB) is a prerequisite for the reliable estimation of surface melt and the surface mass balance over ice and snow. This study quantifies the SEB closure by comparing the energy available for surface melt, determined from continuous measurements of radiative fluxes and turbulent heat fluxes, to the surface ablation measured on the Greenland ice sheet between 2003 and 2023. We find that the measured daily energy available for surface melt exceeds the observed surface melt by on average 18 ± 30W m-2 for snow and 12 ± 54W m-2 for ice conditions (mean ± SD), which corresponds to 46 and 10% of the average energy available for surface melt, respectively. When the surface is not melting, the daily SEB is on average closed within 5W m-2. Based on the inter-comparison of different ablation sensors and radiometers installed on different stations, and on the evaluation of modelled turbulent heat fluxes, we conclude that measurement uncertainties prevent a better daily to sub-daily SEB closure. These results highlight the need and challenges in obtaining accurate long-term in situ SEB observations for the proper evaluation of climate models and for the validation of remote sensing products. [ABSTRACT FROM AUTHOR]

Seismic imaging in 3-D holds great potential for improving our understanding of ice sheet structure and dynamics. Conducting 3-D imaging in remote areas is simplified by using lightweight and logistically straightforward sources. We report results from controlled seismic source tests carried out near the West Antarctic Ice Sheet Divide investigating the characteristics of two types of surface seismic sources, Poulter shots and detonating cord, for use in both 2-D and 3-D seismic surveys on glaciers. Both source types produced strong basal P-wave and S-wave reflections and multiples recorded in three components. The Poulter shots had a higher amplitude for low frequencies (<10 Hz) and comparable amplitude at high frequencies (>50 Hz) relative to the detonating cord. Amplitudes, frequencies, speed of source set-up, and cost all suggested Poulter shots to be the preferred surface source compared to detonating cord for future 2-D and 3-D seismic surveys on glaciers. [ABSTRACT FROM AUTHOR]

This study examines the performance of low-cost, low-power GNSS positioning systems for glacier monitoring in high-latitude environments. We compare the positioning performance of co-located low-cost u-blox ZED-F9P GNSS units (a few hundred USDs) and survey-grade Trimble R10 units (> $10,000 USD) under stationary (on land) and dynamic (on glacier) conditions near Terra Nova Bay, Antarctica. Low-cost and survey-grade systems yield almost identical error magnitudes under short (3 m), medium (34 km) and long (390 km) baseline kinematicpositioning scenarios. We further examined the efficacy of low-cost GNSS for glaciological applications by installing four u-blox and two Trimble receivers on Priestley Glacier to observe tidemodulated ice flexure. All receivers successfully detected subtle tidal oscillations with amplitudes < 3 cm, consistent with the predicted phasing from a tide model. These experiments offer a strong rationale for the widespread use of low-cost receivers to expand and densify GNSS monitoring networks, both in Antarctica and in glaciated regions worldwide. [ABSTRACT FROM AUTHOR]

We developed a multi-frequency, multi-Global Navigation Satellite System (GNSS) positioning instrument optimized for autonomous applications in the cryosphere. At lower power requirements and a fraction of the cost and weight compared to commercially available options, this instrument simplifies field usage and associated logistics. In this paper, we assess several baseline aspects of performance in a polar environment relative to geodetic receivers commonly used for glaciological applications. Evaluations of precision and relative accuracy of positioning show millimeter to centimeter-level ('geodetic-grade') quality of this instrument, making it a competitive alternative for GNSS glaciological and geophysical applications such as monitoring surface elevation change and ice flow. An array of these instruments, tested in the field on the Greenland Ice Sheet, also demonstrated robustness throughout the polar winter and met power and reliability requirements. [ABSTRACT FROM AUTHOR]

Glacier and ice sheet research is frequently justified on the basis of potential benefits to those communities that are most vulnerable to glacier change. In this glaciology research, funding priorities and communication to the broader public are strongly affected by the experiences and values of glaciology researchers. Using population data and newly available survey data from research organizations including glaciologists, we show that there is a substantial misalignment between the demographics of those who stand to benefit from glaciological research and those who produce glaciological knowledge. We discuss the potential negative consequences of this misalignment, which causes scientific research to be less effective, valuable and usable for communities. We conclude by outlining twenty evidence-based strategies that individuals and organizations can adopt to improve the recruitment and retention of a more representative group of scientists in glaciological research and encourage co-production with communities. [ABSTRACT FROM AUTHOR]

Observations of glacier melt and runoff are of fundamental interest in the study of glaciers and their interactions with their environment. Considerable recent interest has developed around distributed acoustic sensing (DAS), a sensing technique which utilizes Rayleigh backscatter in fiber optic cables to measure the seismo-acoustic wavefield in high spatial and temporal resolution. Here, we present data from a month-long, 9 km DAS deployment extending through the ablation and accumulation zones on Rhonegletscher, Switzerland, during the 2020 melt season. While testing several types of machine learning (ML) models, we establish a regression problem, using the DAS data as the dependent variable, to infer the glacier discharge observed at a proglacial stream gauge. We also compare two predictive models that only depend on meteorological station data. We find that the seismo-acoustic wavefield recorded by DAS can be utilized to infer proglacial discharge. Models using DAS data outperform the two models trained on meteorological data with mean absolute errors of 0.64, 2.25 and 2.72m3 s-1, respectively. This study demonstrates the ability of in situ glacier DAS to be used for quantifying proglacial discharge and points the way to a new approach to measuring glacier runoff. [ABSTRACT FROM AUTHOR]

Ice shelves regulate the flow of the Antarctic ice sheet toward the ocean and its contribution to sea-level rise. Accurately monitoring the basal and surface melting of ice shelves is therefore essential for predicting the ice sheet's response to climatic warming. In this study, we utilize Sentinel-1A synthetic aperture radar satellite imagery combined with shipboard measurements of water temperature and salinity to investigate the presence of surficial meltwater plumes along the Antarctic coastline. Our approach reveals a strong correlation between areas of pronounced low radar backscatter extending from ice shelves and significant decreases in water temperature and salinity, suggesting meltwater-enriched ocean waters. We propose that the low radar backscatter signature of meltwater outflows is caused by stable stratification of the upper water column, driven by density contrasts from buoyant, low-salinity meltwater and surface current shear that reduce Bragg scattering waves. The resulting smooth water surfaces were observed adjacent to the surface expression of deep basal channels, documented in a helicopter survey along part of the Bellingshausen Sea ice edge. We present high-temporal resolution satellite radar as a tool for identifying meltwater release from beneath ice shelves, capable of all-weather, day-and-night imaging. [ABSTRACT FROM AUTHOR]

Shallow firn cores, in addition to a near-basal ice core, were recovered in 2018 from the Quelccaya ice cap (5470 m a.s.l) in the Cordillera Vilcanota, Peru, and in 2017 from the Nevado Illimani glacier (6350 m a.s.l) in the Cordillera Real, Bolivia. The two sites are ~450 km apart. Despite meltwater percolation resulting from warming, particle-based trace element records (e.g. Fe, Mg, K) in the Quelccaya and Illimani shallow cores retain well-preserved signals. The firn core chronologies, established independently by annual layer counting, show a convincing overlap indicating the two records contain comparable signals and therefore capture similar regional scale climatology. Trace element records at a ~1–4 cm resolution provide past records of anthropogenic emissions, dust sources, volcanic emissions, evaporite salts and marine-sourced air masses. Using novel ultra-high-resolution (120 μm) laser technology, we identify annual layer thicknesses ranging from 0.3 to 0.8 cm in a section of 2000-year-old radiocarbon-dated near-basal ice which compared to the previous annual layer estimates suggests that Quelccaya ice cores drilled to bedrock may be older than previously suggested by depth-age models. With the information collected from this study in combination with past studies, we emphasize the importance of collecting new surface-to-bedrock ice cores from at least the Quelccaya ice cap, in particular, due to its projected disappearance as soon as the 2050s.

A precise knowledge of landfast sea-ice (fast-ice) thickness is relevant to many different disciplines. Sea Ice Monitoring Stations (SIMS) are used to measure time series of fast-ice thickness at a location. SIMS measure ice and ocean temperature via thermistor strings with many different methods for extracting sea-ice thickness from temperature existing. This study investigates: if thickness results from temperature recorded by SIMS of different designs, and analysed with different methods are comparable; which methods are recommended for their robustness, precision and accuracy and how they compare to independent thickness measurements; how otherwise unuseable data can be salvaged through specific SIMS designs. We present an analysis of fast-ice thickness calculated from SIMS deployed in McMurdo Sound, Antarctica and in the Chukchi Sea near Utqiaġvik, Alaska, over two decades. We find that median thicknesses derived by different methods agree within 1 ± 1.5 cm for McMurdo Sound and 2 ± 3 cm for Utqiaġvik. Thus, it is possible to confidently compare data collected from different stations and analysed with different methods. The vertical gradient of sea-ice temperature gives the best results for fast-ice thickness during the growth season and including standard resistors in a thermistor string can reduce potential data loss due to noise.

To better constrain meltwater transport and ice viscosity in temperate glaciers, particularly in ice stream shear margins, we use a custom permeameter to study the untested model relationship between the permeability of temperate ice and its liquid water content. The permeability of lab-made ice of two mean grain diameters (1.8 and 4.2 mm) is measured, and water content is controlled with the ice salinity and measured calorimetrically. Fluorescein dye is added to through-flowing, chilled water to highlight flow pathways through the ice after experiments. As predicted by a simple model, permeability increases with approximately the square of the water content and by about three orders of magnitude across water contents of 0.1–4.4%. However, permeability values are less than those of the model by average factors of 2.6 and 4.1 for the finer and coarser ice, respectively. This discrepancy is likely due to tortuous, truncated or air-clogged veins. The order-of-magnitude agreement between measured and modeled values may indicate that reduced permeability from these factors is nearly compensated by preferential flow in oversized veins that are isolated or arborescent. Both kinds of preferred flow pathways are observed but the latter only in fine-grained ice at water contents > 2%. [ABSTRACT FROM AUTHOR]

We present seismic measurements of the firn column at Korff Ice Rise, West Antarctica, including measurements of compressional-wave velocity and attenuation. We describe a modified spectral-ratio method of measuring the seismic quality factor (Q) based on analysis of diving waves, which, combined with a stochastic method of error propagation, enables us to characterise the attenuative structure of firn in greater detail than has previously been possible. Q increases from 56 ± 23 in the uppermost 12 m to 570 ± 450 between 55 and 77 m depth. We corroborate our method with consistent measurements obtained via primary reflection, multiple, source ghost, and critically refracted waves. Using the primary reflection and its ghost, we find Q = 53 ± 20 in the uppermost 20 m of firn. From the critical refraction, we find Q = 640 ± 400 at 90 m depth. Our method aids the understanding of the seismic structure of firn and benefits characterisation of deeper glaciological targets, providing an alternative means of correcting seismic reflection amplitudes in cases where conventional methods of Q correction may be impossible. [ABSTRACT FROM AUTHOR]

Recent research has highlighted the potential for high-resolution, high-density, 3D and 4D ground-penetrating radar (GPR) acquisitions on alpine glaciers. When carried out on foot, such surveys are laborious and time consuming, which limits their application to small domains of limited glaciological interest. Further, crevasses and other hazards make the data acquisition risky. To address these issues, we have developed a drone-based GPR system. The system has a payload weight of 2.2 kg and a data output rate of 14 traces per second. An 80-MHz antenna and a recording time of 2800 ns mean that depths of over 100 m can be reached in temperate ice. Differential GPS positioning assures accurate flight paths. At a speed of 4 m s−1 and height of 5 m above the glacier surface, our system can acquire over 4 line-km of GPR data in 20 min on a single set of drone batteries. After presenting the technical specifications of the system and tests required to optimize its performance, we showcase a recently acquired 3D dataset from the Otemma glacier in Switzerland, where 462 parallel GPR profiles were surveyed at a 1-m line spacing, totaling over 112 line-km of data, in only 4 days. [ABSTRACT FROM AUTHOR]

Converting measurements of ice-sheet surface elevation change to mass change requires measurements of accumulation and knowledge of the evolution of the density profile in the firn. Most firn-densification models are tuned using measured depth–density profiles, a method which is based on an assumption that the density profile in the firn is invariant through time. Here we present continuous measurements of firn-compaction rates in 12 boreholes near the South Pole over a 2 year period. To our knowledge, these are the first continuous measurements of firn compaction on the Antarctic plateau. We use the data to derive a new firn-densification algorithm framed as a constitutive relationship. We also compare our measurements to compaction rates predicted by several existing firn-densification models. Results indicate that an activation energy of 60 kJ mol−1, a value within the range used by current models, best predicts the seasonal cycle in compaction rates on the Antarctic plateau. Our results suggest models can predict firn-compaction rates with at best 7% uncertainty and cumulative firn compaction on a 2 year timescale with at best 8% uncertainty. [ABSTRACT FROM AUTHOR]

We present a method for tracking radio-tagged pebbles and cobbles through subglacial meltwater channels under shallow temperate glaciers. Natural particles tagged with active radio transmitters were injected directly into a large subglacial channel 300 m up-glacier from the terminus of the Glacier d'Otemma, Switzerland. A roving antenna was developed to localise tagged particles planimetrically in subglacial and proglacial channel reaches (350 and 150 m long, respectively) using a probabilistic technique, delivering records of the change in particle location and transport distance over time with uncertainty. The roving antenna had a ±5−15 m planimetric precision, a 75% particle localisation rate and operated at a maximum ice depth of 47 m. Additionally, stationary supraglacial and proglacial antennas continuously monitored the passage of tagged particles through consecutive reaches of the channel, constraining the timing of particle transport events. The proglacial antenna system had a 98.1% detection rate and was operational to 0.89 m water depth during testing. Roving and stationary antenna records were combined to create a transport distance model for each particle, which may be used in conjunction with hydraulic data to investigate the kinematics of particle motion. When applied at scale in future studies, this method may be used to reveal the mechanisms and timescales of coarse sediment export from Alpine glaciers. [ABSTRACT FROM AUTHOR]

Progress in our understanding of wave–ice interactions is currently hindered by the lack of in situ observations and information of sea-ice properties, including the elastic modulus. Here, we estimate the effective elastic modulus of sea ice using observations of waves in ice through the deployment of three open-source geophone recorders on landfast sea ice. From observations of low-frequency dispersive waves, we obtain an estimate of the effective elastic modulus in the range of 0.4–0.7 GPa. This is lower than the purely elastic modulus of the ice estimated at 1 GPa as derived from in situ beam experiments. Importantly, our experimental observation is significantly lower than the default value currently in use in wave models. While our estimate is not representative for all sea ice, it does indicate that considerably more measurements are required to provide confidence in the development of parameterizations for this complex sea-ice property for wave models. [ABSTRACT FROM AUTHOR]

A 198.8 m deep borehole was drilled through ice to subglacial bedrock in the northwestern marginal part of Princess Elizabeth Land, ~12 km south of Zhongshan Station, in January–February 2019. Three years later, in February 2022, the borehole temperature profile was measured, and the geothermal heat flow (GHF) was estimated using a 1-D time-dependent energy-balance equation. For a depth corresponding to the base of the ice sheet, the GHF was calculated as 72.6 ± 2.3 mW m−2 and temperature −4.53 ± 0.27°C. The regional averages estimated for this area based, generally, on tectonic setting vary from 55 to 66 mW m−2. A higher GHF is interpreted to originate mostly from the occurrence of metamorphic complexes intruded by heat-producing elements in the subglacial bedrock below the drill site. [ABSTRACT FROM AUTHOR]

Debris-covered glaciers are an important component of the mountain cryosphere and influence the hydrological contribution of glacierized basins to downstream rivers. This study examines the potential to make estimates of debris thickness, a critical variable to calculate the sub-debris melt, using ground-based thermal infrared radiometry (TIR) images. Over four days in August 2019, a ground-based, time-lapse TIR digital imaging radiometer recorded sequential thermal imagery of a debris-covered region of Peyto Glacier, Canadian Rockies, in conjunction with 44 manual excavations of debris thickness ranging from 10 to 110 cm, and concurrent meteorological observations. Inferring the correlation between measured debris thickness and TIR surface temperature as a base, the effectiveness of linear and exponential regression models for debris thickness estimation from surface temperature was explored. Optimal model performance (R2 of 0.7, RMSE of 10.3 cm) was obtained with a linear model applied to measurements taken on clear nights just before sunrise, but strong model performances were also obtained under complete cloud cover during daytime or nighttime with an exponential model. This work presents insights into the use of surface temperature and TIR observations to estimate debris thickness and gain knowledge of the state of debris-covered glacial ice and its potential hydrological contribution.

We developed automated ablation stakes to measure colocated in situ changes in relative glacier-surface elevation and climatological drivers of ablation. The designs, refined over 10 years of development and deployments, implement open-source hardware and common building materials. The ablation stakes record distance to the snow/ice surface, air temperature and relative humidity every 1–15 min. Using these high-frequency data, we demonstrate that melt factors calculated using standard melt-rate vs temperature regressions converge over averaging windows of approximately 12 h or greater. Furthermore, we evaluate an integral approach to estimating temperature-index melt factors for ablation. In a test case on Glaciar Perito Moreno, Argentina, this integral approach reveals an overall positive-degree-day melt factor of 7.5 mm w.e. $^\circ$ C−1 d−1. We describe four deployments with iteratively improved designs and provide a list of materials required to construct an automated ablation stake. [ABSTRACT FROM AUTHOR]

The geodetic mass balance of a glacier corresponds to glacier-wide volume changes, converted to mass changes using density assumptions. It is typically calculated by differencing multi-temporal digital elevation models. In this study, we show how the annual geodetic mass balance of a glacier can be derived from uncrewed aerial vehicle (UAV) data. The presented workflow is applied to two small- to medium-sized glaciers in the Kyrgyz Tien Shan (Central Asia): Bordu glacier and Sary-Tor glacier. The obtained geodetic mass balance is compared with the glaciological mass balance derived from a network of ablation stakes and snow pits. A previously calibrated mass-balance model is used to correct for the difference in acquisition dates. The results show that the determined geodetic mass balance matches closely with the glaciological mass balance. Besides, for both glaciers the geodetic mass balance does not seem to be particularly sensitive to the assumptions regarding volume-to-mass conversion. Therefore, our results demonstrate that UAVs can serve as a valuable instrument to quantify the annual geodetic mass balance and to validate the glaciological mass balance. The conventional glaciological mass-balance estimation often relies on interpolation and extrapolation methods, whereas UAVs offer the potential for direct data acquisition over the entire glacier surface. [ABSTRACT FROM AUTHOR]

A precise knowledge of landfast sea-ice (fast-ice) thickness is relevant to many different disciplines. Sea Ice Monitoring Stations (SIMS) are used to measure time series of fast-ice thickness at a location. SIMS measure ice and ocean temperature via thermistor strings with many different methods for extracting sea-ice thickness from temperature existing. This study investigates: if thickness results from temperature recorded by SIMS of different designs, and analysed with different methods are comparable; which methods are recommended for their robustness, precision and accuracy and how they compare to independent thickness measurements; how otherwise unuseable data can be salvaged through specific SIMS designs. We present an analysis of fast-ice thickness calculated from SIMS deployed in McMurdo Sound, Antarctica and in the Chukchi Sea near Utqiaġvik, Alaska, over two decades. We find that median thicknesses derived by different methods agree within 1 ± 1.5 cm for McMurdo Sound and 2 ± 3 cm for Utqiaġvik. Thus, it is possible to confidently compare data collected from different stations and analysed with different methods. The vertical gradient of sea-ice temperature gives the best results for fast-ice thickness during the growth season and including standard resistors in a thermistor string can reduce potential data loss due to noise. [ABSTRACT FROM AUTHOR]

Shallow firn cores, in addition to a near-basal ice core, were recovered in 2018 from the Quelccaya ice cap (5470 m a.s.l) in the Cordillera Vilcanota, Peru, and in 2017 from the Nevado Illimani glacier (6350 m a.s.l) in the Cordillera Real, Bolivia. The two sites are ~450 km apart. Despite meltwater percolation resulting from warming, particle-based trace element records (e.g. Fe, Mg, K) in the Quelccaya and Illimani shallow cores retain well-preserved signals. The firn core chronologies, established independently by annual layer counting, show a convincing overlap indicating the two records contain comparable signals and therefore capture similar regional scale climatology. Trace element records at a ~1–4 cm resolution provide past records of anthropogenic emissions, dust sources, volcanic emissions, evaporite salts and marine-sourced air masses. Using novel ultra-high-resolution (120 μm) laser technology, we identify annual layer thicknesses ranging from 0.3 to 0.8 cm in a section of 2000-year-old radiocarbon-dated near-basal ice which compared to the previous annual layer estimates suggests that Quelccaya ice cores drilled to bedrock may be older than previously suggested by depth-age models. With the information collected from this study in combination with past studies, we emphasize the importance of collecting new surface-to-bedrock ice cores from at least the Quelccaya ice cap, in particular, due to its projected disappearance as soon as the 2050s. [ABSTRACT FROM AUTHOR]

The production of meltwater from glacier ice, which is exposed at the margins of land ice during the summer, is responsible for a large proportion of glacier mass loss. The rate of meltwater production from glacier ice is especially sensitive to its physical structure and chemical composition which combine to determine the albedo of glacier ice. However, the optical properties of near-surface glacier ice are not well known since most prior work has focused on laboratory-grown ice or deep cores. Here, we demonstrate a measurement technique based on diffuse propagation of nanosecond-duration laser pulses in near-surface glacier ice that enables the independent measurement of the scattering and absorption coefficients, allowing for a complete description of the processes governing radiative transfer. We employ a photon-counting detector to overcome the high losses associated with diffuse optics. The instrument is highly portable and rugged, making it optimally suited for deployment in remote regions. A set of measurements taken on Crook and Collier Glaciers, Oregon, serves as a demonstration of the technique. These measurements provide insight into both physical structure and composition of near-surface glacier ice and open new avenues for the analysis of light-absorbing impurities and remote sensing of the cryosphere.

The vast Greenland and Antarctic Ice Sheets are covered by many tens of meters of polar firn, which is snow that is years to centuries old and has experienced significant metamorphism. Both ice-sheet modeling and decoding satellite data require knowledge of the thermal conductivity of polar firn with depth, yet direct measurements are not available for depths below the top several meters. We present the first direct measurements of the effective thermal conductivity of polar firn over depths down to 48 m. A custom guarded hot plate has been designed and constructed, and validation of this device using materials of known thermal conductivity is presented. Using the validated device, measurements were made on firn core samples spanning depths from 4 to 48 m from an undisturbed site near the South Pole, Antarctica. Results show that the thermal conductivity of polar firn at South Pole increases with depth and with density. The thermal conductivity of polar firn from the surface to 48 m depth is well-explained as a function of density by the relationship kfirn(ρ) = 0.144 e0.00308·ρ and as a function of depth by the relationship kfirn(z) = 0.536 e0.0144·z. The associated thermal diffusivities range from 19.0 to 28.5 m2 a-1.

The englacial and subglacial drainage systems exert key controls on glacier dynamics. However, due to their inaccessibility, they are still only poorly understood and more detailed observations are important, particularly to validate and tune physical models describing their dynamics. By creating artificial glacier moulins – boreholes connected to the subglacial drainage system and supplied with water from surface streams – we present a novel method to monitor the evolution of an englacial hydrological system with high temporal resolution. Here, we use artificial moulins as representations for vertical, pressurised, englacial R-channels. From tracer and pressure measurements, we derive time series of the hydraulic gradient, discharge, flow speed and channel cross-sectional area. Using these, we compute the Darcy–Weisbach friction factor, obtaining values which increase from 0.1 to 13 within five days of channel evolution. Furthermore, we simulate the growth of the cross-sectional area using different temperature gradients. The comparison to our measurements largely supports the common assumption that the temperature follows the pressure melting point. The deviations from this behaviour are analysed using various heat transfer parameterisations to assess their applicability. Finally, we discuss how artificial moulins could be combined with glacier-wide tracer experiments to constrain parameters of subglacial drainage more precisely.

Debris-covered glaciers are an important component of the mountain cryosphere and influence the hydrological contribution of glacierized basins to downstream rivers. This study examines the potential to make estimates of debris thickness, a critical variable to calculate the sub-debris melt, using ground-based thermal infrared radiometry (TIR) images. Over four days in August 2019, a ground-based, time-lapse TIR digital imaging radiometer recorded sequential thermal imagery of a debris-covered region of Peyto Glacier, Canadian Rockies, in conjunction with 44 manual excavations of debris thickness ranging from 10 to 110 cm, and concurrent meteorological observations. Inferring the correlation between measured debris thickness and TIR surface temperature as a base, the effectiveness of linear and exponential regression models for debris thickness estimation from surface temperature was explored. Optimal model performance (R 2 of 0.7, RMSE of 10.3 cm) was obtained with a linear model applied to measurements taken on clear nights just before sunrise, but strong model performances were also obtained under complete cloud cover during daytime or nighttime with an exponential model. This work presents insights into the use of surface temperature and TIR observations to estimate debris thickness and gain knowledge of the state of debris-covered glacial ice and its potential hydrological contribution. [ABSTRACT FROM AUTHOR]

Ocean-driven melt of Antarctic ice shelves is an important control on mass loss from the ice sheet, but is complex to study due to significant variability in melt rates both spatially and temporally. Here we assess the strengths and weakness of satellite and field-based observations as tools for testing models of ice-shelf melt. We discuss how the complementary use of field, satellite and model data can be a powerful but underutilised tool for studying melt processes. Finally, we identify some community initiatives working to collate and publish coordinated melt rate datasets, which can be used in future for validating satellite-derived maps of melt and evaluating processes in numerical simulations.

Close-range sensors are employed to observe glaciological processes that operate over short timescales (e.g. iceberg calving, glacial lake outburst floods, diurnal surface melting). However, under poor weather conditions optical instruments fail while the operation of radar systems below 17 GHz do not have sufficient angular resolution to map glacier surfaces in detail. This letter reviews the potential of millimetre-wave radar at 94 GHz to obtain high-resolution 3-D measurements of glaciers under most weather conditions. We discuss the theory of 94 GHz radar for glaciology studies, demonstrate its potential to map a glacier calving front and summarise future research priorities.

Citizen science and related engagement programmes have proliferated in recent years throughout the sciences but have been reasonably limited in the cryospheric sciences. In the semiarid Andes we at the Centro de Estudios Avanzados en Zonas Áridas have developed a range of initiatives together with the wider community and stakeholder institutions to improve our understanding of the role snow and ice play in headwater catchments. In this paper we reflect on ongoing engagement with communities living and working in and near study sites of cryospheric science in northern Chile as a strategy that can both strengthen the research being done and empower local communities.

Distributed Acoustic Sensing (DAS) is increasingly recognised as a valuable tool for glaciological seismic applications, although analysing the large data volumes generated in acquisitions poses computational challenges. We show the potential of active-source DAS to image and characterise subglacial sediment beneath a fast-flowing Greenlandic outlet glacier, estimating the thickness of sediment layers to be 20–30 m. However, the lack of subglacial velocity constraint limits the accuracy of this estimate. Constraint could be provided by analysing cryoseismic events in a counterpart 3-day record of passive seismicity through, for example, seismic tomography, but locating them within the 9 TB data volume is computationally inefficient. We describe experiments with data compression using the frequency-wavenumber (f-k) transform ahead of training a convolutional neural network, that provides a ~300-fold improvement in efficiency. In combining active and passive-source and our machine learning framework, the potential of large DAS datasets could be unlocked for a range of future applications.

Ice-penetrating radar sounding is a powerful geophysical tool for studying terrestrial and planetary ice with a rich glaciological heritage reaching back over half a century. Recent years have also seen rapid growth in both the radioglaciological community itself and in the scope and sophistication of its analysis of ice-penetrating radar data. This has been spurred by a combination of growing datasets and improvements in computational resources as well as advances in radar sounding instrumentation and platforms. Together, these developments are transforming the field and highlight exciting paths forward for future innovation and investigation.

Heated needle probes provide the most convenient method to measure snow thermal conductivity. Recent studies have suggested that this method underestimates snow thermal conductivity; however the reasons for this discrepancy have not been elucidated. We show that it originates from the fact that, while the theory behind the method assumes that the measurements reach a logarithmic regime, this regime is not reached within the standard measurement procedure. Using the needle probe without this logarithmic regime leads to thermal conductivity underestimations of tens of percents. Moreover, we show that the poor thermal contact between the probe and the snow due to insertion damages results in a further underestimation. Thus, we encourage the use of fixed needle probes, set up before the snow season and buried under snowfalls, rather than hand-inserted probes. Finally, we propose a method to correct the measurements performed with such fixed needle probes buried in snow. This correction is based on a lookup table, derived specifically for the Hukseflux TP02 needle probe model, frequently used in snow studies. Comparison between corrected measurements and independent estimations of snow thermal conductivity obtained with numerical simulations shows an overall improvement of the needle probe values after application of the correction.

Results of ice-stream models that treat temperate ice deformation as a two-phase flow are sensitive to the ice permeability. We have constructed and begun using a custom, falling-head permeameter for measuring the permeability of temperate, polycrystalline ice. Chilled water is passed through an ice disk that is kept at the pressure-melting temperature while the rate of head decrease indicates the permeability. Fluorescein dye in the water allows water-vein geometry to be studied using fluorescence microscopy. Water flow over durations of seconds to hours is Darcian, and for grain diameter d increasing from 1.7 to 8.9 mm, average permeability decreases from 2 × 10−12 to 4 × 10−15 m2. In tests with dye on fine (d = 2 mm) and coarse (d = 7 mm) ice, average area-weighted vein radii are nearly equal, 41 and 34 μm, respectively. These average radii, if included in a theory slightly modified from Nye and Frank (1973), yield permeability values within a factor of 2.0 of best-fit values based on regression of the data. Permeability values depend on d−3.4, rather than d−2 as predicted by models if vein radii are considered independent of d. In future experiments, the dependence of permeability on liquid water content will be measured.

To understand snow structure and snowmelt timing, information about flows of liquid water within the snowpack is essential. Models can make predictions using explicit representations of physical processes, or through parameterization, but it is difficult to verify simulations. In situ observations generally measure bulk quantities. Where internal snowpack measurements are made, they tend to be destructive and unsuitable for continuous monitoring. Here, we present a novel method for in situ monitoring of water flow in seasonal snow using the electrical self-potential (SP) geophysical method. A prototype geophysical array was installed at Col de Porte (France) in October 2018. Snow hydrological and meteorological observations were also collected. Results for two periods of hydrological interest during winter 2018–19 (a marked period of diurnal melting and refreezing, and a rain-on-snow event) show that the electrical SP method is sensitive to internal water flow. Water flow was detected by SP signals before it was measured in conventional snowmelt lysimeters at the base of the snowpack. This initial feasibility study shows the utility of the SP method as a non-destructive snow sensor. Future development should include combining SP measurements with a high-resolution snow physics model to improve prediction of melt timing.

Polycrystalline ice is known to exhibit macroscopic anisotropy in relative permittivity (ɛ) depending on the crystal orientation fabric (COF). Using a new system designed to measure the tensorial components of ɛ, we investigated the dielectric anisotropy (Δɛ) of a deep ice core sample obtained from Dome Fuji, East Antarctica. This technique permits the continuous nondestructive assessment of the COF in thick ice sections. Measurements of vertical prism sections along the core showed that the Δɛ values in the vertical direction increased with increasing depth, supporting previous findings of c-axis clustering around the vertical direction. Analyses of horizontal disk sections demonstrated that the magnitude of Δɛ in the horizontal plane was 10–15% of that in the vertical plane. In addition, the directions of the principal axes of tensorial ɛ in the horizontal plane corresponded to the long or short axis of the elliptically elongated single-pole maximum COF. The data confirmed that Δɛ in the vertical and horizontal planes adequately indicated the preferred orientations of the c-axes, and that Δɛ can be considered to represent a direct substitute for the normalized COF eigenvalues. This new method could be extremely useful as a means of investigating continuous and depth-dependent variations in COF.

Dissolved and particulate sodium, magnesium and calcium are analyzed in ice cores to determine past changes in sea ice extent, terrestrial dust variability and atmospheric aerosol transport efficiency. They are also used to date ice cores if annual layers are visible. Multiple methods have been developed to analyze these important compounds in ice cores. Continuous flow analysis (CFA) is implemented with instruments that sample the meltstream continuously. In this study, CFA with ICP-MS (inductively coupled-plasma mass spectrometry) and fast ion chromatography (FIC) methods are compared for analysis of sodium and magnesium. ICP-MS, FIC and fluorescence methods are compared for analysis of calcium. Respective analysis of a 10 m section of the Antarctic WACSWAIN Skytrain Ice Rise ice core shows that all of the methods result in similar levels of the compounds. The ICP-MS method is the most suitable for analysis of the Skytrain ice core due to its superior precision (relative standard deviation: 1.6% for Na, 1.3% for Mg and 1.2% for Ca) and sampling frequency compared to the FIC method. The fluorescence detection method may be preferred for calcium analysis due to its higher depth resolution (1.4 cm) relative to the ICP-MS and FIC methods (~4 cm).

Firn compaction models inform mass-balance estimates and paleo-climate reconstructions, but current models introduce key uncertainties. For example, models disagree on the dependence of density and compaction on accumulation rate. Observations of compaction to test these models are rare, partly because in situ methods for measuring englacial strain are time-consuming and expensive. Moreover, shallow measurements may confound strain due to compaction with strain due to ice-sheet flow. We show that phase-sensitive radio-echo sounder (pRES) systems, typically deployed to measure sub-shelf melting or ice-sheet deformation, can be used to measure firn compaction and test firn models. We present two complementary methods for extracting compaction information from pRES data, along with a method for comparing compaction models to pRES observations. The methods make different assumptions about the density structure and vary in their need for independent density measurements. Compaction profiles computed from pRES data collected on three ice rises in West Antarctica are largely consistent with measured densities and a physics-based model. With their minimal logistic requirements, new pRES systems, such as autonomous pRES, could be inexpensively deployed to monitor firn compaction more widely. Existing phase-sensitive radar data may contain compaction information even when surveys targeted other processes.

The production of meltwater from glacier ice, which is exposed at the margins of land ice during the summer, is responsible for a large proportion of glacier mass loss. The rate of meltwater production from glacier ice is especially sensitive to its physical structure and chemical composition which combine to determine the albedo of glacier ice. However, the optical properties of near-surface glacier ice are not well known since most prior work has focused on laboratory-grown ice or deep cores. Here, we demonstrate a measurement technique based on diffuse propagation of nanosecond-duration laser pulses in near-surface glacier ice that enables the independent measurement of the scattering and absorption coefficients, allowing for a complete description of the processes governing radiative transfer. We employ a photon-counting detector to overcome the high losses associated with diffuse optics. The instrument is highly portable and rugged, making it optimally suited for deployment in remote regions. A set of measurements taken on Crook and Collier Glaciers, Oregon, serves as a demonstration of the technique. These measurements provide insight into both physical structure and composition of near-surface glacier ice and open new avenues for the analysis of light-absorbing impurities and remote sensing of the cryosphere. [ABSTRACT FROM AUTHOR]

The vast Greenland and Antarctic Ice Sheets are covered by many tens of meters of polar firn, which is snow that is years to centuries old and has experienced significant metamorphism. Both ice-sheet modeling and decoding satellite data require knowledge of the thermal conductivity of polar firn with depth, yet direct measurements are not available for depths below the top several meters. We present the first direct measurements of the effective thermal conductivity of polar firn over depths down to 48 m. A custom guarded hot plate has been designed and constructed, and validation of this device using materials of known thermal conductivity is presented. Using the validated device, measurements were made on firn core samples spanning depths from 4 to 48 m from an undisturbed site near the South Pole, Antarctica. Results show that the thermal conductivity of polar firn at South Pole increases with depth and with density. The thermal conductivity of polar firn from the surface to 48 m depth is well-explained as a function of density by the relationship k firn(ρ) = 0.144 e 0.00308· ρ and as a function of depth by the relationship k firn(z) = 0.536 e 0.0144· z . The associated thermal diffusivities range from 19.0 to 28.5 m2 a-1. [ABSTRACT FROM AUTHOR]

The englacial and subglacial drainage systems exert key controls on glacier dynamics. However, due to their inaccessibility, they are still only poorly understood and more detailed observations are important, particularly to validate and tune physical models describing their dynamics. By creating artificial glacier moulins – boreholes connected to the subglacial drainage system and supplied with water from surface streams – we present a novel method to monitor the evolution of an englacial hydrological system with high temporal resolution. Here, we use artificial moulins as representations for vertical, pressurised, englacial R-channels. From tracer and pressure measurements, we derive time series of the hydraulic gradient, discharge, flow speed and channel cross-sectional area. Using these, we compute the Darcy–Weisbach friction factor, obtaining values which increase from 0.1 to 13 within five days of channel evolution. Furthermore, we simulate the growth of the cross-sectional area using different temperature gradients. The comparison to our measurements largely supports the common assumption that the temperature follows the pressure melting point. The deviations from this behaviour are analysed using various heat transfer parameterisations to assess their applicability. Finally, we discuss how artificial moulins could be combined with glacier-wide tracer experiments to constrain parameters of subglacial drainage more precisely. [ABSTRACT FROM AUTHOR]