Search

Data were obtained on the copolymerization of ethylene with α-olefins over supported titanium–magnesium catalysts (TMC) prepared on the same magnesium dichloride support but differing in the composition and oxidation state of titanium. The copolymerization kinetics of ethylene with 1-hexene over TMC of different compositions were studied. Data on the composition of the produced ethylene–1-hexene copolymers, their molecular weight distribution, thermophysical characteristics, and branching distribution were presented. The constants of ethylene–1-hexene copolymerization over catalysts with different compositions were calculated. The TMC containing only Ti(II) compounds as the active component exhibited increased copolymerizing ability compared to the conventional TiCl4/MgCl2 catalyst containing Ti(III) compounds as the active component. In addition, TMC with Ti(II) as an active component produces copolymers with a more uniform branching distribution. It was shown that the TMC containing isolated Ti(II) ions could be used to produce X-ray amorphous ethylene-propylene elastomers with a high yield. [ABSTRACT FROM AUTHOR]

Data were obtained on the copolymerization of ethylene with α-olefins over supported titanium–magnesium catalysts (TMC) prepared on the same magnesium dichloride support but differing in the composition and oxidation state of titanium. The copolymerization kinetics of ethylene with 1-hexene over TMC of different compositions were studied. Data on the composition of the produced ethylene–1-hexene copolymers, their molecular weight distribution, thermophysical characteristics, and branching distribution were presented. The constants of ethylene–1-hexene copolymerization over catalysts with different compositions were calculated. The TMC containing only Ti(II) compounds as the active component exhibited increased copolymerizing ability compared to the conventional TiCl4/MgCl2 catalyst containing Ti(III) compounds as the active component. In addition, TMC with Ti(II) as an active component produces copolymers with a more uniform branching distribution. It was shown that the TMC containing isolated Ti(II) ions could be used to produce X-ray amorphous ethylene-propylene elastomers with a high yield.

This study aims to investigate the influences of a combination of cocatalysts including triethylaluminum (TEA) and tri-n-octylaluminum (TnOA) for activation of a commercial Ti-based Ziegler-Natta catalyst during ethylene polymerization and ethylene/1-hexene copolymerization on the change in Ti3+ during polymerization. Thus, electron spin resonance (ESR) technique was performed to monitor the change in Ti3+ depending on the catalyst activation by a single and combination of cocatalyst. It revealed that the amount of Ti3+ played a crucial role on both ethylene polymerization and ethylene/1-hexene copolymerization. For ethylene polymerization, the activation with TEA apparently resulted in the highest catalytic activity. The activation with TEA+TnOA combination exhibited a moderate activity, whereas TnOA activation gave the lowest activity. In case of ethylene/1-hexene copolymerization, it revealed that the presence of 1-hexene decreased activity. The effect of different cocatalysts tended to be similar to the one in the absence of 1-hexene. The decrease of temperature from 80 to 70 °C in ethylene/1-hexene copolymerization tended to lower catalytic activity for TnOA and TEA+TnOA, whereas only slight effect was observed for TEA system. The effect of different cocatalyst activation on the change of Ti3+ state of catalyst was elucidated by ESR measurement. It appeared that the activation of catalyst with TEA+TnOA combination essentially inhibited the reduction of Ti3+ to Ti2+ leading to lower activity. Furthermore, the polymer properties such as morphology and crystallinity can be altered by different cocatalysts. Copyright © 2020 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).

This study aims to investigate the influences of a combination of cocatalysts including triethylaluminum (TEA) and tri-n-octylaluminum (TnOA) for activation of a commercial Ti-based Ziegler-Natta catalyst during ethylene polymerization and ethylene/1-hexene copolymerization on the change in Ti3+ during polymerization. Thus, electron spin resonance (ESR) technique was performed to monitor the change in Ti3+ depending on the catalyst activation by a single and combination of cocatalyst. It revealed that the amount of Ti3+ played a crucial role on both ethylene polymerization and ethylene/1-hexene copolymerization. For ethylene polymerization, the activation with TEA apparently resulted in the highest catalytic activity. The activation with TEA+TnOA combination exhibited a moderate activity, whereas TnOA activation gave the lowest activity. In case of ethylene/1-hexene copolymerization, it revealed that the presence of 1-hexene decreased activity. The effect of different cocatalysts tended to be similar to the one in the absence of 1-hexene. The decrease of temperature from 80 to 70 °C in ethylene/1-hexene copolymerization tended to lower catalytic activity for TnOA and TEA+TnOA, whereas only slight effect was observed for TEA system. The effect of different cocatalyst activation on the change of Ti3+ state of catalyst was elucidated by ESR measurement. It appeared that the activation of catalyst with TEA+TnOA combination essentially inhibited the reduction of Ti3+ to Ti2+ leading to lower activity. Furthermore, the polymer properties such as morphology and crystallinity can be altered by different cocatalysts. [ABSTRACT FROM AUTHOR]

In this study, the influences of the Ti oxidation state on the catalytic properties of MgCl-supported Ziegler-Natta catalysts in ethylene homo- and co-polymerization with 1-hexene were investigated. Three catalysts having different Ti oxidation states were synthesized by milling TiCl, TiCl, or TiCl together with MgCl. With these catalysts having different Ti oxidation states, the polymerization conditions such as the Al concentration, temperature, and 1-hexene concentration were varied to figure out their catalytic abilities in ethylene homo- and co-polymerization. The Ti oxidation state affected the catalyst activity largely, having unique dependences on the polymerization conditions. A higher oxidation state led to a higher activity, slightly larger comonomer incorporation, and lower molecular weight as well as its narrower distribution. However, rough characteristics of copolymers were similar among the different Ti oxidation states. [ABSTRACT FROM AUTHOR]

Supported titanium–magnesium catalysts (TMC) comprising isolated and clustered titanium ions in different oxidation states, which are obtained using titanium compounds of different composition (TiCl4, TiCl3•nDBE (DBE – dibutyl ether), [η6–BenzeneTiAl2Cl8]), were synthesized and tested in ethylene polymerization. The state of titanium ions was studied by the ESR method both for the procatalysts and after their interaction with triisobutilaluminum. For identification of ESR‐silent Ti3+ ions and Ti2+ ions, special procedures of additional catalyst treatment with pyridine, water, and chloropentafluorobenzene were used to obtain Ti3+ ions that are observable in ESR spectra. In distinction to numerous earlier works performed with the TiCl4/MgCl2 catalyst comprising after the interaction with AlR3 the Ti3+ surface compounds both as isolated ions and clusters (ESR‐silent), this work considers the [η6–BenzeneTiAl2Cl8]/MgCl2 catalyst (TMC‐3) comprising mainly the isolated Ti2+ ions and a new catalyst TMC‐4 obtained by treating the TMC‐3 with chloropentafluorobenzene. This catalyst comprises only the isolated Ti3+ ions both before and after the interaction with triisobutylaluminum. It was shown that in spite of sharp distinctions between the catalysts under consideration concerning titanium oxidation state and the ratio of isolated Ti3+ ions to clustered ones, all these catalysts produce polyethylenes with similar molecular weights and molecular‐weight distributions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6362–6372, 2009 [ABSTRACT FROM AUTHOR]