Search

Your search keyword '"výroba nábytku"' showing total 17 results
Start Over Descriptor "výroba nábytku"
17 results on '"výroba nábytku"'

1. Využití mikrovlnné plastifikace dřeva při výrobě ohýbaných nábytkových dílců

Author

Nováčková, Kateřina

Subjects
Fagus sylvatica L, mikrovlnný ohřev, ohýbání dřeva, plastifikace dřeva, výroba nábytku, mikrovlnná plastifikace, buk lesní
Abstract

This bachelor thesis is dealing with microwave plasticization for wood shaping and its potential utilization in furniture industry. European beech (Fagus sylvatica L.) specimens of dimensions 20 × 20 × 300 mm were sorted into 8 groups (each group consisted 15 specimens). Reference specimens (Ref1) were tested as oven-dried at room temperature, furthermore reference specimens (Ref2) were tested as oven-dried at 80 °C and last reference group (Ref3) was conditioned to fiber saturation point (FSP). Specimens of conventional, steam plasticization (Vp) were conditioned to FSP and heated at 100 °C for 1 hour. Microwave plasticization was carried out at 1,5 and 3,5 kW using continuous laboratory MW device All MW specimens were soaked in water in order to reach approx. 60 % of MC.Output moisture content (MC) of MW treated specimens was 20 % (MW1), 30 % (MW2, MW4) and 40 % (MW3). Moreover, additional specimens of dimensions 30 × 30 × 450 mm were used to up-scale its possibilities of use. These specimens were sorted into 2 groups (Ref and MW), each group consited 20 specimens. Effect of plasticization was measured by means of static 3-point bending test. Plasticity of wood was evaluated by modulus of elasticity (MOE), modulus of rupture (MOR) and deflection. Results of reference specimens confirmed influence of temperature and moisture content on MOE and MOR. Influence of moisture content (0 % and FSP) was found to be more significant and 65 % decrease of strength MOR and 40 % of MOE is reported. Steam plasticization, as a conventionally used method for shaping, led to increase of plasticity (decrease of MOE about 65 %) and deflection (70 %) when compared to Ref1. Significantly higher deflection (up to 1,5 mm) and increase of plasticity (MOE decreased about 72 %) was found for specimens plasticized by MW at 1,5 kW and 3,5 kW from initial moisture 60 % to output moisture 30 %. Based on results, it can be stated that microwave technology have similar effects on wood plasticity, when compared to conventional method wood plasticization – steaming. Results of present thesis confirmed high potential of MW plasticization for wood shaping. Reduction of time and safe energy might be considered as a great advantage for furniture production. Futher studies should be done in future in order to reveal effect of MW on structural changes, eventually to optimize process for specific shapes.

Published
2018

2. Cenová politika středně velkých podniků zabývajících se výrobou nábytku

Author

Pehalová, Klára

Subjects
cenová politika, analýza tržní struktury, náklady, výroba nábytku, nákladové kalkulace
Abstract

This diploma thesis is focused on pricing policy of furniture companies and their costing calculations. The main goal of the thesis was to formulate recommendations for furniture price setting. The theoretical part of the thesis described market structures, methods of company pricing, costs of the company and methods of cost calculation. In the practical part was defined the market structure of the furniture industry in the Czech Republic. Were mentioned methods of pricing from three different companies and the price of particular order was calculated using each method. At the end of the thesis, recommendations were formulated for better specification the calculation procedures used by companies.

Published
2018

3. Přístup malých a středních podniků k faktorům úspěchu

Author

Hálová, Naďa

Subjects
malý a střední podnik, výroba nábytku, klíčové faktory úspěchu, model hodnocení klíčových faktorů úspěchu, internacionalizace
Abstract

The diploma thesis deals with access of small and medium enterprises operating in the field of furniture production to internal factors of success. From the analysis of domestic and foreign literature and scientific works, thirteen hypotheses were pronounced, which were further tested. In order to fulfill the main objective of the work, ie to identify the differences in the attitude of SMEs operating in the Czech Republic and SMEs operating abroad, primary data collection was carried out. Both quantitative and qualitative investigations were performed. These results together with a brief description of the current situation of SMEs in the Czech Republic and furniture production were the main part of my thesis. The secondary objective was to propose SME recommendations for furniture manufacturers.

Published
2018

4. The relationship between indebtedness and productivity at company level

Author

VAŇÁČOVÁ, Hana

Subjects
velikost podniků, produktivita, production of furniture, manufacturing industry, indebtedness, company size, zpracovatelský průmysl, výroba nábytku, productivity, zadluženost
Abstract

This diploma thesis is focusing on analysis of indebtedness and productivity at company level. The main aim is to analyse these two variables and find their relationship. The thesis is divided into two main parts, theoretical and practical. The theoretical part includes information about indebtedness and productivity issues, whereas the practi-cal part is focusing on analysing of these two variables and finding their relationship. It is focused on companies producing furniture. In the introduction of the practical part is a characteristics of furniture manufacturing industry according to the CZ-NACE and a summarization from a macroeconomic perspective. These companies are than cate-gorized by their size into micro, small, medium and large companies. The following chapters are aimed on a produc-tivity and indebtedness analysis according to each category and on analysis of their relationship. The last chapter is aimed on hypothesis that is supposed to find out, if the companies, that have long-term asset and indebtedness growth, have also a productivity growth. The conclusion includes a summary of all the analysis. According to the analysis was found out, that in some small groups of companies exist a significant relationship between productivity and indebted-ness. It is mainly about a medium and large companies.

Published
2016

5. Odvětvové prostředí výroby nábytku v ČR

Author

Špačková, Lucie

Subjects
strategické skupiny, výroba nábytku, atraktivita odvětví, Porterův model, analýza odvětví
Abstract

This dissertation thesis deals with the furniture manufacturing sector in Czech Republic. The main aim of the dissertation thesis is to define recommendations of strategic options and recommendations for competitiveness of enterprises on the basis of executed analysis of furniture manufacturing industry. The theoretical part gives an overview of industry analysis methods which are described in literature. The practical part of the thesis applies selected analysis to furniture manufacturing industry in Czech Republic, demonstrates results of research via questionnaire, which are mainly focused on the large and medium size enterprises and in this part are recommended suggestions for competitiveness of enterprises in the industry. Recommendations for Czech furniture manufacturers include e.g. improve a marketing and deepening cooperation with scientific institutions.

Published
2012

6. Financial analysis TON a.s

Author

Koutská, Jitka, Sieber, Martina, and Cimický, Jan

Subjects
Financial analysis, TON a.s, Manufacturing of furniture, Finanční analýza, Výroba nábytku
Abstract

The goal of this bachelor thesis was an analysis of fundamental financial indicators of TON a. s. for the years 2004 - 2008, an assessment of their development and a comparison within the business branch. To obtain the required values were used: horizontal and vertical analysis, ratio indicators, models of creditworthiness and indicator EVA.

Published
2009

7. Návrh na zlepšení procesů ve výrobní firmě metodou 5S

Author

Bayerová, Vladimíra, Kašpar, Michal, Matušková, Lucie, Bayerová, Vladimíra, Kašpar, Michal, and Matušková, Lucie

Abstract

Diplomová práce je zaměřena na návrh projektu zavedení metody 5S do výrobního systému společnosti LAUFEN CZ, s.r.o., ve městě Znojmě. Návrh reaguje na současnou ekonomickou situaci a také na stav společnosti. Jedná se o druhou fázi projektu se zaměřením na výrobu a kompletaci koupelnového nábytku. V práci jsou vyhodnoceny postupy a metody pro úspěšnou realizaci projektu., The master thesis is focused on a proposal of project implementation of 5S method for production system of LAUFEN CZ, s.r.o. in Znojmo. The proposal reacts to current economic situation and also to the status of company. This is the second phase of project with focusing on the production and completion of bathroom furniture. In master thesis are evaluated correct process and methods for successful implementation of project.

8. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Neuner, Jakub, Šuhajda, Karel, Straka,, Bohumil, and Neuner, Jakub

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

9. Návrh na zlepšení procesů ve výrobní firmě metodou 5S

Author

Bayerová, Vladimíra, Kašpar, Michal, Matušková, Lucie, Bayerová, Vladimíra, Kašpar, Michal, and Matušková, Lucie

Abstract

Diplomová práce je zaměřena na návrh projektu zavedení metody 5S do výrobního systému společnosti LAUFEN CZ, s.r.o., ve městě Znojmě. Návrh reaguje na současnou ekonomickou situaci a také na stav společnosti. Jedná se o druhou fázi projektu se zaměřením na výrobu a kompletaci koupelnového nábytku. V práci jsou vyhodnoceny postupy a metody pro úspěšnou realizaci projektu., The master thesis is focused on a proposal of project implementation of 5S method for production system of LAUFEN CZ, s.r.o. in Znojmo. The proposal reacts to current economic situation and also to the status of company. This is the second phase of project with focusing on the production and completion of bathroom furniture. In master thesis are evaluated correct process and methods for successful implementation of project.

10. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Neuner, Jakub, Šuhajda, Karel, Straka,, Bohumil, and Neuner, Jakub

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

11. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Šuhajda, Karel, and Straka,, Bohumil

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

12. Návrh na zlepšení procesů ve výrobní firmě metodou 5S

Author

Bayerová, Vladimíra, Kašpar, Michal, Bayerová, Vladimíra, and Kašpar, Michal

Abstract

Diplomová práce je zaměřena na návrh projektu zavedení metody 5S do výrobního systému společnosti LAUFEN CZ, s.r.o., ve městě Znojmě. Návrh reaguje na současnou ekonomickou situaci a také na stav společnosti. Jedná se o druhou fázi projektu se zaměřením na výrobu a kompletaci koupelnového nábytku. V práci jsou vyhodnoceny postupy a metody pro úspěšnou realizaci projektu., The master thesis is focused on a proposal of project implementation of 5S method for production system of LAUFEN CZ, s.r.o. in Znojmo. The proposal reacts to current economic situation and also to the status of company. This is the second phase of project with focusing on the production and completion of bathroom furniture. In master thesis are evaluated correct process and methods for successful implementation of project.

13. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Šuhajda, Karel, and Straka,, Bohumil

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

14. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Šuhajda, Karel, and Straka,, Bohumil

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

15. Návrh na zlepšení procesů ve výrobní firmě metodou 5S

Author

Bayerová, Vladimíra, Kašpar, Michal, Bayerová, Vladimíra, and Kašpar, Michal

Abstract

Diplomová práce je zaměřena na návrh projektu zavedení metody 5S do výrobního systému společnosti LAUFEN CZ, s.r.o., ve městě Znojmě. Návrh reaguje na současnou ekonomickou situaci a také na stav společnosti. Jedná se o druhou fázi projektu se zaměřením na výrobu a kompletaci koupelnového nábytku. V práci jsou vyhodnoceny postupy a metody pro úspěšnou realizaci projektu., The master thesis is focused on a proposal of project implementation of 5S method for production system of LAUFEN CZ, s.r.o. in Znojmo. The proposal reacts to current economic situation and also to the status of company. This is the second phase of project with focusing on the production and completion of bathroom furniture. In master thesis are evaluated correct process and methods for successful implementation of project.

16. Návrh na zlepšení procesů ve výrobní firmě metodou 5S

Author

Bayerová, Vladimíra, Kašpar, Michal, Bayerová, Vladimíra, and Kašpar, Michal

Abstract

Diplomová práce je zaměřena na návrh projektu zavedení metody 5S do výrobního systému společnosti LAUFEN CZ, s.r.o., ve městě Znojmě. Návrh reaguje na současnou ekonomickou situaci a také na stav společnosti. Jedná se o druhou fázi projektu se zaměřením na výrobu a kompletaci koupelnového nábytku. V práci jsou vyhodnoceny postupy a metody pro úspěšnou realizaci projektu., The master thesis is focused on a proposal of project implementation of 5S method for production system of LAUFEN CZ, s.r.o. in Znojmo. The proposal reacts to current economic situation and also to the status of company. This is the second phase of project with focusing on the production and completion of bathroom furniture. In master thesis are evaluated correct process and methods for successful implementation of project.

17. Administrativní budova s výrobnou nábytku

Author

Šuhajda, Karel, Straka,, Bohumil, Neuner, Jakub, Šuhajda, Karel, Straka,, Bohumil, and Neuner, Jakub

Abstract

Diplomová práca rieši návrh administratívnej budovy s výrobnou nábytku. Stavba je situovaná v Brne v katastrálnom území Horní Heršpice. Objekt je dispozične a konštrukčne rozdelený na dve časti, výrobnú halu a administratívnu časť s hygienickými zázemím pre pracovníkov vo výrobe, s jedálňou pre zamestnancov a s priestormi na vystavovanie nábytku. Výrobná hala je jednoposchodová so skeletovým nosným systémom z lepeného lamelového dreva. Administratívna časť má dve nadzemná poschodia. Zvislé a vodorovné nosné konštrukcie tvoria panely z krížom lepeného dreva. Fasáda objektu je navrhnutá ako vetraná, časť fasády je tvorená cemento-vláknitými doskami a časť dreveným obkladom doplneným o vegetačné panely. Strecha celého objektu je navrhnutá ako jednoplášťová vegetačná., The aim of this master thesis is to design a building consisting of joiner workshop and administration part of furniture factory. Building is located in Brno, cadastral area Horní Herpšice. In terms of funcion as well as structure is building devided in two parts, joiner workshop and administration part containing hygienic facilities for workers, canteen for employees and furniture showroom. Joiner workshop is single-deck skelet structure made of glued laminated timber. Administration part has two above-grade floors. Cross laminated timber panels are used for vertical and horizontal bearing structures. Building facade is designed as ventilated, partly made of cement fiber boards, partly of timber boarding along with green panels. The building has one-layer green roof.

Catalog

Books, media, physical & digital resources
See catalog results