Search

In this paper, we propose a method for calculating the DC source amplitude in an extended multilevel inverter (MLI) structure so that the maximum number of levels and the output voltage waveform are as close as possible to the sinusoidal wave with minimum total harmonic distortion (THD). For the developed structure, three algorithms are suggested to determine the amounts of DC voltage resources. The first important point about choosing the right amounts for the DC resources is that the number of levels should be as large as possible, and the second important point is that the intervals between the levels should be the same throughout the waveform. By observing these two points, the output voltage waveform can be as near as possible to the sinusoidal wave that we want. In this study, we used iteration-based methods to find suitable values for DC sources. Simulation results are offered to confirm the capability of the extended multilevel converter. After we solved the problem through calculation and analysis, a code was written in MATLAB with the aim that this time the code will tell us for what values of DC sources we will have the largest number of levels and as we expected, the output of the MATLAB code confirmed the correctness of the calculations. [ABSTRACT FROM AUTHOR]

As a key component of high‐performance switches and routers, the packet forwarding engine (PFE) is mainly responsible for selecting the appropriate output port for tens of thousands of packets within an extremely short time frame. However, the performance of PFE is determined by the selected group membership algorithm. This paper puts forth a hybrid strategy–caching scalar‐pair and vectors routing and forwarding (CSVRF), consisting of virtual output port bitmap caching (VOPBC) and fractional‐N SVRF to address major multicast forwarding issues such as scalability by using content addressable memory. In CSVRF, a virtual output port bitmap cache is introduced, which includes the most popular combinations of output port bitmap and divides the big scalar‐pair into N sub‐groups to achieve parallel compute and the reusability of less bit‐length prime. The results demonstrate that the memory space and the forwarding latency are effectively reduced compared with previous work. In space efficiency, it only required 10% memory space compared with the original SVRF/fractional‐N SVRF, decreased 10% memory usage compared with pure VOPBC and nearly improved 1 to 4 orders of magnitude of packet processing time compared with the original SVRF and the fractional‐N SVRF respectively. [ABSTRACT FROM AUTHOR]

With the advantages of low power consumption, flexibility, and high readability against bright ambiance, electrophoretic displays (EPDs) have wide application prospects in the fields of education, smart supermarkets, Internet of Things, smart homes, wearable devices, etc. EPDs suffer from a severe history dependence during grayscale switching, which results in annoying ghost images. However, currently, it is difficult to distinguish diverse types of ghost images automatically; thus, lookup-tables (LUTs) for multi-grayscale waveform design cannot be effectively generated but require cumbersome manual adjustment. In this article, we proposed to adopt a convolutional neural network (CNN) to automatically recognize ghost images, based on which, LUTs that could suppress ghost images and achieve accurate grayscales were automatically generated for waveform design. Moreover, the workforce for manual adjustment was significantly saved. The results suggest that the CNN is a powerful tool for EPDs to achieve better image quality, as well as less manual cost. [ABSTRACT FROM AUTHOR]

This paper presents an advanced technique for calculating activation energy of oil-impregnated pressboard through dielectric response current measurement under switching impulse voltage at different temperatures. The proposed technique analyzes the measured impulse voltage and current signals to formulate its equivalent circuit at different temperatures. The equivalent circuit parameters are utilized to determine the shifting of ac conductivity curve along frequency axis with variations in temperatures. Based on the shifted ac conductivity curves at different temperatures, the corresponding activation energy of the insulation is estimated. The effectiveness of the proposed technique is investigated through a few laboratory prepared test samples. [ABSTRACT FROM AUTHOR]

The overhead of memory virtualization remains nontrivial. The traditional shadow paging (TSP) resorts to a shadow page table (SPT) to achieve the native page walk speed, but page table updates require hypervisor interventions. Alternatively, nested paging enables low-overhead page table updates, but utilizes the hardware MMU to perform a long-latency two-dimensional page walk. This paper proposes new memory virtualization solutions based on hardware (machine) mode—the highest CPU privilege level in some architectures like Sunway and RISC-V. A programming interface, running in hardware mode, enables software-implementation of hardware support functions. We first propose Software-based Nested Paging (SNP), which extends the software MMU to perform a two-dimensional page walk in hardware mode. Second, we present Swift Shadow Paging (SSP), which accomplishes page table synchronization by intercepting TLB flushing in hardware mode. Finally we propose Accelerated Shadow Paging (ASP) combining SSP and SNP. ASP handles the last-level SPT page faults by walking two-dimensional page tables in hardware mode, which eliminates most hypervisor interventions. This paper systematically compares multiple memory virtualization models by analyzing their designs and evaluating their performance both on a real system and a simulator. The experiments show that the virtualization overhead of ASP is less than 4.5% for all workloads. [ABSTRACT FROM AUTHOR]

In this paper, a simple yet effective network pruning framework is proposed to simultaneously address the problems of pruning indicator, pruning ratio, and efficiency constraint. This paper argues that the pruning decision should depend on the convolutional weights, and thus proposes novel weight-dependent gates (W-Gates) to learn the information from filter weights and obtain binary gates to prune or keep the filters automatically. To prune the network under efficiency constraints, a switchable Efficiency Module is constructed to predict the hardware latency or FLOPs of candidate pruned networks. Combined with the proposed Efficiency Module, W-Gates can perform filter pruning in an efficiency-aware manner and achieve a compact network with a better accuracy-efficiency trade-off. We have demonstrated the effectiveness of the proposed method on ResNet34, ResNet50, and MobileNet V2, respectively achieving up to 1.33/1.28/1.1 higher Top-1 accuracy with lower hardware latency on ImageNet. Compared with state-of-the-art methods, W-Gates also achieves superior performance. [ABSTRACT FROM AUTHOR]

This paper proposes an optimization approach for day-ahead reactive power planning to improve voltage security in transmission networks. The problem is formulated as a voltage-secure multi-period optimal reactive power dispatch (MP-ORPD) problem. The optimization approach searches for optimal set-points of dynamic and static reactive power (var) resources. Specifically, the output includes set-points for switching shunts, transformer taps, and voltage magnitudes at the regulated buses. The primary goal is to maximize the dynamic reactive power reserve of the system, by minimizing the reactive power supplied by synchronous generators. As the size of the MP-ORPD problem increases significantly with increasing number of contingencies and time periods, efficiency is crucial for practical applications. In this paper, a decomposition technique based on consensus and alternating optimization, where integer variable targets are obtained via MILP, is used to partition the MP-ORPD problem into a set of subproblems, which can be solved in parallel to reduce the computation time. The proposed MP-ORPD problem and its solution algorithm are integrated into the EPRI-VCA software. The results of various power networks of large electric utilities in the Eastern interconnection demonstrate the effectiveness of the proposed algorithm in providing preventive control schedules. [ABSTRACT FROM AUTHOR]

In order to achieve the purpose of extending the speed range and reducing power electronics devices for the permanent-magnet linear motor drive system, a half-centralized open-end winding (OEW) topology is studied for rail transit applications in this paper. In this topology, compared with the traditional OEW topology, the number of voltage-source-inverters (VSIs) can be reduced from four to three to drive two OEW movers and all these VSIs share a common dc bus voltage. In order to improve the steady-state performances, a four-vector phase model predictive voltage control (FV-PMPVC) is proposed in this paper. Due to the spatial distribution of phase voltage vector (PVV), an orthometric synthesis principle (OSP) is proposed to calculated the duration time for the vector synthesis, which reduces the computation burden and enhances the robustness. Comparing the existing control method, FV-PMPVC can get similar dynamic performances but better steady-state performances. Additionally, the half-centralized topology using FV-PMPVC can have same speed range while less VSIs are required. The effectiveness of FV-PMPVC is verified by experimental results. [ABSTRACT FROM AUTHOR]

Weather-related or other types of faults can negatively impact the continuity of the electricity delivery to the consumers and, thus, lead to poorer reliability scores. 90% of customer outage-minutes are due to events which affect local distribution systems. The radial configuration is simple and has a low cost design; however, when a fault occurs it often causes power outages beyond the location of the fault itself. Therefore, it is beneficial for utilities to automatically isolate the fault and, thus, restore power to as many consumers as possible. The benefits of fault isolation and service restoration include, but are not limited to: enhanced reliability and resiliency, reduced loss of revenue to the utility, and enhanced comfort and satisfaction for the utility’s consumers. This paper provides an algorithm to quickly isolate a fault and automatically restore power to as many nodes of the distribution system as possible by opening and closing switches already placed within the system. The expert model and centralized algorithm that are proposed in this paper guarantee an optimal solution and a short run-time regardless of the size of the distribution system. A mathematical proof of the optimal nature of the solution is provided. In addition, the model is validated in practice, solving two different-sized systems. [ABSTRACT FROM AUTHOR]

In this paper, we demonstrate biocompatible micromachined buckled membranes for the operation in liquids. The membranes feature diameters between 600 and 800 $\mu \text{m}$ as well as integrated piezoelectric thin film actuators, thus enabling switching between the bistable states. The membrane material is known to be not biocompatible, hence a hydrogenated amorphous silicon carbide (a-SiC:H) layer is deposited on the surface. For demonstration purposes, a 70 nm ±3 nm thin a-SiC:H coating with a specific silicon to carbon ratio was chosen, with a negligible impact on the overall switching performance of the bistable membranes. Furthermore, a relation between the membrane center velocity at the first characteristic resonance frequency and the switching ability of a membrane in different viscous fluids is shown. Based on a small signal analysis the switching behavior can be predicted. The membranes were successfully switched in liquids with a dynamic viscosity up to 286 mPa $\cdot \text{s}$. The biocompatibility of the membranes was examined by growing Caco-2 cells, a human carcinoma cell line, on a-SiC:H thin films, featuring different carbon contents and organic surface treatments. The proliferation and adhesion of the cells on the substrates are examined in an empirical cell growth and removal study. Only a-SiC:H surfaces pre-treated with an O2-plasma and coated with Collagen Type I indicated to provide an environment of improved cell adhesiveness compared to other surface treatments. The biological investigations resulted in good cell proliferation, that also depends on the altered hydrophilicity of the surface, as well as on the carbon content of the a-SiC:H thin films. This study reveals that a broad range of biocompatible a-SiC:H surfaces can be prepared, whereby the cell growth can be tailored in terms of proliferation and adhesion for different biomedical application scenarios. Finally, this paper reports on the mechanical features of bistable, buckled membranes and their suitability as a growth substrate for human cell cultures, due to the good biocompatibility of a-SiC:H thin films. We therefore suggest that it will be feasible to grow cells on bistable MEMS membranes, enabling cell experiments in liquid medical environments, with both mechanically excitable and biocompatible surfaces. [2022-0006] [ABSTRACT FROM AUTHOR]

In this paper, a new modulation strategy based on the carrier-based switching strategy for the non-square direct matrix converters (MC) is proposed to control the active power of distributed generation (DG) units. In this strategy, the active power of DGs is controlled by the central input current control of the non-square direct MC independent from the voltage and frequency. Conventionally, each DG has a converter, and for supplying a load with N number of DGs, N number of converters are needed and each converter has its own modulation switching and control strategy to control the power output of each DG. Needless to say, in a microgrid with N number of DGs, the control strategy of each converter has more complex structure than that of a microgrid with one converter, and surely the former strategy entails more volume and price. Using the proposed converter in this paper, it is possible to supply a load with N number of DGs through one converter. Also, the power outputs of all DGs are controlled by a central control strategy. The proposed central control strategy is described and simulated for a typical microgrid. Experimental and simulation results validate the effectiveness of the proposed converter and the proposed strategy. The results demonstrate the applicability and efficiency of the system and verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

Background: Verbal fluency tasks are routinely used in clinical assessment and research studies of aphasia. People with aphasia produce fewer items in verbal fluency tasks. It remains unclear if their output is limited solely by their lexical difficulties and/or has a basis in their executive control abilities. Recent research has illustrated that detailed characterization of verbal fluency performance using temporal characteristics of words retrieved, clustering and switching, and pause durations, along with separate measures of executive control stands to inform our understanding of the lexical and cognitive underpinnings of verbal fluency in aphasia. Aims: To determine the locus of the verbal fluency difficulties in aphasia, we compared semantic and letter fluency trials between people with aphasia and healthy control participants using a wide range of variables to capture the performance between the two groups. The groups were also tested on separate measures of executive control to determine the relationship amongst these tasks and fluency performance. Methods & Procedures: Semantic (animal) and letter (F, A, S) fluency data for 60s trials were collected from 14 people with aphasia (PWA) and 24 healthy adult controls (HC). Variables, such as number of correct responses, clustering and switching analyses, were performed along with temporal measures of the retrieved words (response latencies) and pause durations. Participants performed executive control tasks to measure inhibitory control, mental‐set shifting and memory span. Outcomes & Results: Compared with HC, PWA produced fewer correct responses, showed greater difficulty with the letter fluency condition, were slower in getting started with the trials, showed slower retrieval times as noted in within‐ and between‐cluster pause durations, and switched less often. Despite these retrieval difficulties, PWA showed a similar decline in the rate of recall to HC, and had similar cluster size. Executive control measures correlated primarily with the letter fluency variables: mostly for PWA and in one instance for HC. Conclusions & Implications: Poorer performance for PWA is a combination of difficulties in both the lexical and executive components of the verbal fluency task. Our findings highlight the importance of detailed characterization of fluency performance in deciphering the underlying mechanism of retrieval difficulties in aphasia, and illustrate the importance of using letter fluency trials to tap into executive control processes. WHAT THIS PAPER ADDS: What is already known on the subject: PWA typically show impaired performance in verbal fluency tasks. It is debated whether this impaired performance is a result of their lexical difficulties or executive control difficulties, or a combination of both. This debate continues because previous studies have mostly used semantic fluency condition without including letter fluency condition; used a limited range of variables (e.g., number of correct responses); and not included separate executive control measures to explain the performance pattern in aphasia. This research addresses these outstanding issues to determine the specific contribution of lexical and executive control processes in verbal fluency in aphasia by including: both semantic and letter fluency conditions; a wide range of variables to identify the relative contribution of lexical and executive control mechanisms; and independent measures of executive control. What this paper adds to existing knowledge: Using the multidimensional analysis approach for verbal fluency performance from both semantic and letter fluency conditions, this is the first study to systematically demonstrate that PWA had difficulties in both lexical and executive control components of the task. At the individual level, PWA had greater difficulty on the letter fluency condition compared with semantic fluency. We observed significant correlations between the executive control measures and verbal fluency measures primarily for the letter fluency condition. This research makes a significant contribution to our understanding of lexical and executive control aspects in word production in aphasia. What are the potential or actual clinical implications of this work?: From a clinical perspective, this research highlights the importance of using a full range of verbal fluency and executive control measures to tap into the lexical as well as executive control abilities of PWA, and also the utility of using letter fluency to tap into the executive control processes in PWA. [ABSTRACT FROM AUTHOR]

This article discusses an advanced method for estimating dc conductivity of oil using parameters evaluated under switching impulse voltage application. Firstly, the effectiveness of switching impulse application for assessing the condition of oil–paper insulation is investigated. Thereafter, the evaluated parameters under switching impulse voltage are fitted by Havriliak and Negami (HN) model for estimating the oil conductivity. The method is applied on oil-impregnated pressboards containing different moistures and a distribution transformer for experimental investigation. Moreover, the limitations of the proposed method are also discussed in this article. [ABSTRACT FROM AUTHOR]

This paper proposes an accurate impedance model for line commutated converter (LCC) in the stationary frame. The commutation overlap process caused by the transformer leakage inductance complicates the modeling for LCC. Traditional impedance models are derived in positive sequence and negative sequence frame based on the simplified commutation overlap process, which degrades the modeling accuracy and limits the description of frequency coupling. This paper systematically analyzes the effects of the commutation overlap process on the impedance model, and the impedance model with the accurate commutation overlap process is established in the dq-frame. For clearly revealing the frequency coupling phenomenon of the LCC, the complex space vector is employed to extend the impedance model in the dq-frame to the complex αβ-frame. A closed-loop model on PSCAD/EMTDC is used to verify the proposed impedance model in the time-domain and the frequency-domain. The consistency between the simulation results and theoretical analysis effectively verifies the accuracy of the proposed model. [ABSTRACT FROM AUTHOR]

This paper presents an optimization framework for sequential reconfiguration using an assortment of switching devices and repair process in distribution system restoration. Compared to existing studies, this paper considers types, capabilities and operational limits of different switching devices, making it applicable in practice. We develop a novel multi-phase method to find the optimal sequential operation of various switching devices and repair faulted areas. We consider circuit breakers, reclosers, sectionalizers, load breaker switches, and fuses. The switching operation problem is decomposed into two mixed-integer linear programming (MILP) subproblems. The first subproblem determines the optimal network topology and estimates the number of steps to reach that topology, while the second subproblem generates a sequence of switching operations to coordinate the switches. For repairing the faults, we design an MILP model that dispatches repair crews to clear faults and replace melted fuses. After clearing a fault, we update the topology of the network by generating a new sequence of switching operations, and the process continues until all faults are cleared. To improve the computational efficiency, a network reduction algorithm is developed to group line sections, such that only switchable sections are present in the reduced network. The proposed method is validated on the IEEE 123-bus and 8500-bus systems. [ABSTRACT FROM AUTHOR]

This paper presents the possibilities of reducing emergency situations and reducing the time of failure in the power grid. The paper contains a detailed description of the method (algorithm) of operation in emergency situations on the example of a Gas-Insulated Switchgear (GIS) located in one of the system-forming (node) stations in the power grid. The level of detail contained in this paper, which has not been previously encountered in previous publications, favors an in-depth understanding of the possible solutions that result from these emergencies. The above method (algorithm) of activities has been developed based on three levels of research: simulation, theoretical and practical. This means that the simulation analysis that was performed based on theoretical information was experimentally tested as part of an emergency situation in one of the system-forming (nodal) stations in the power system. In order to achieve the result described in this article, one of the most promising types of devices used in power systems was selected - the GIS. This has been confirmed by numerous analyzes of the effectiveness of these devices included in this article. The paper contains a detailed description of the individual steps in the field of corrective actions and aimed at minimizing downtime. In addition, this article provides guidance to monitor possible emergencies that are designed to increase the reliability of the power grid. [ABSTRACT FROM AUTHOR]

The degradation of the electrical contact in a gas insulated switchgear (GIS) is closely related to overheating at the contact. However, the disconnector contact is one of the hot contacts in GIS. Therefore, in this paper, the finite element method was used to solve the three-dimensional multiphysics coupling temperature rise field and flow field in the Single Phase in One Tank (SPIOT) type GIS disconnector under different operating conditions. From the perspective of temperature rise field and flow field, this paper analyzed the temperature rise characteristics under different working conditions and explored the feasibility of the direct application of air, CO2 and C4F7N/CO2 mixed gas to an electrical device. The disconnector temperature rise experiment platform was then built to verify the simulation. The results showed that the temperature rise field and the flow field distribution were similar in four gas environments. SF6 gas had the smallest temperature rise, followed by C4F7N/CO2 mixed gas, and the temperature rise of CO2 and air was relatively large. Therefore, from the perspective of the temperature rise field and flow field, it was feasible to directly apply C4F7N/CO2 mixed gas to an electrical device in order to meet insulation requirements. [ABSTRACT FROM AUTHOR]

Light-emitting diodes (LEDs) are widely used in street lighting, landscape lighting, liquid crystal display (LCD) backlighting, healthcare, etc. As an important part of LED lighting products, LED driver plays a vital role in maintenance costs reduction, energy saving and lifetime prolongation. In this paper, a single-stage LED driver is proposed, which is integrated by a totem-pole bridgeless power factor correction (PFC) unit and several modular LCL-T resonant rectifiers. The totem-pole bridgeless PFC unit and the LCL-T resonant rectifiers are integrated by sharing switches, which can simplify the circuit and reduce the system cost. The output current can be regulated by applying the variable inductor control. Constant duty cycle and fixed switching frequency operation can be achieved as well. The operating principle and the performance of the proposed converter are analyzed in this paper. In addition, a precise parameter design method is proposed by considering the high-order harmonics. At last, an experimental prototype is established to validate the proposed parameter design and variable inductor control method. [ABSTRACT FROM AUTHOR]

This paper presents a different Finite Control Set – Model Predictive Control (FCS-MPC) for grid-connected three-phase bidirectional power inverters. These are typically used in dc or ac renewable-based microgrids (MGs), where bidirectional operation and fast dynamic response is required. The bidirectional grid-connected inverters are an essential part of MG, which inject energy into the ac grid or demand energy from it. The dynamic behavior of the system is a major concern since the current can suddenly change depending on the hierarchical controller. This paper proposes a different cost function using sliding mode theory, which offers a good dynamic response, reduced computational burden, and a parameter-free control model. The operation principle of the proposed controller is given and evaluated using a Hardware-In-the-Loop (HIL) system, but also experimentally with a 1kW laboratory prototype. The final results demonstrate the advantages of using this approach in grid-connected three-phase bidirectional power inverters in terms of dynamic response and reduced computational burden, making this solution technically attractive and viable. [ABSTRACT FROM AUTHOR]

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

The capacitor condition monitoring is an important issue for the reliable operation of modular multilevel converters (MMCs) in high-voltage applications. The numerous capacitors make the monitoring for the capacitor condition complex and computation-consuming. This paper proposes a hierarchic capacitor condition monitoring strategy to assure the reliability of high-voltage MMCs. In the strategy, the switching times of the switching signals are counted to detect the condition of the capacitor in each submodule (SM). Then, the subsequent capacitance calculation method is only conducted to the abnormal capacitors indicated by the above condition detection algorithm. Meanwhile, the variations of the measured and reference capacitor voltages are employed to calculate the capacitance in the proposed method. The condition detection algorithm shrinks the scope where the abnormal capacitors locate, which avoids calculating the total capacitances in MMCs. In the proposed capacitance calculation method, the complex operations are further saved. Both the two measures reduce the computation burden effectively. The implementation of the whole monitoring strategy is simple and fit for high-voltage MMCs. Moreover, the strategy has no adverse influence on the normal operation of MMCs. The effectiveness of the proposed strategy is verified by the simulation studies with the professional tool Matlab/Simulink. [ABSTRACT FROM AUTHOR]

In the conventional sliding mode control, the four-leg distribution static compensator (DSTATCOM) currents are controlled based on a current error in each phase. However, the four currents in a four-wire system can not be independently controlled variables and hence one of the four controllers is redundant in conventional schemes. Further, the current dynamics of a DSTATCOM converter are coupled through converter pole voltages in the natural reference frame. This leads to cross-coupling in the sliding variable equations with respect to four manipulated input variables. Considering the above points, in this paper, the current due to Thevenin’s equivalent load neutral-point voltage is considered as a fourth independent controlled variable and the corresponding system dynamic equations are presented. To get a decoupled feature, a new sliding surface function is structured. The performance of a DSTATCOM with the proposed control scheme under various operating conditions is validated through a detailed simulation study and experimental results, obtained from a laboratory prototype of four-leg DSTATCOM. [ABSTRACT FROM AUTHOR]

In recent years, very high frequency (VHF) converter has attracted much attention. However, with rich parasitic parameters and complex resonance links, there are some great difficulties to the modeling of such systems. Taking the on-off controlled VHF resonant boost converter as an example, this paper presents an accurate modeling and analysis method that considers multiple parasitic parameters. First, the closed-loop VHF converter system is divided into a main network and a parasitic oscillation network. Then, based on the operation analysis, an equivalent circuit model characterized by a time-varying input voltage source and two variable duty-cycle controlled switches is proposed. It worth noting that both the time-varying input and the controlled switches take into account the influences of the parameters. Furthermore, the periodic approximate analytical solution of the output voltage in the on stage is obtained by using the equivalent small parameter method to the proposed circuit model. And then combining the solution of the parasitic oscillation network and on-off state switching conditions, the steady-state waveform of output voltage can be obtained quickly. Finally, a prototype with operating frequency of 21.44 MHz is built to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Conventional model predictive control (MPC) for three-level active neutral point clamped converter (ANPC) utilizes weighting factors to achieve the optimal control of multiple control objectives in a single cost function. However, the selection of these weighting factors has an impact on the performance of the controlled objectives significantly. Tuning of weighting factors is usually tedious and lacks theoretical background. Moreover, the predictive and evaluation process for multiple objectives optimization have to be carried out by enumerating all admissible switching states within one loop. To simplify the complexity of this process and eliminate the effect of weighting factors, this paper proposes a cascaded predictive control scheme for a 3L-ANPC inverter fed induction machine (IM) drive. With the proposed approach, three separate cost functions for three control objectives, stator flux vector, neutral point voltage and device loss distribution are evaluated in a cascaded way, so that the optimization of these control objectives is performed independently. A 3L-ANPC inverter driven IM drive is studied in this paper to verify the effectiveness of the proposed algorithm. Experimental results in different operating conditions confirm that the proposed method achieves satisfactory steady-state and transient performances comparable to the conventional predictive control approach. The weighting factors used in the conventional method are eliminated and the computational effort is reduced by 68% compared to the conventional method without any sacrifice in the drive performance. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

The application of Hall-based BLDC motors ranges from automotive accessory components such as oil and water pumps to high speed compressors. This paper proposes a new twelve-step unsymmetrical 160° commutation strategy using a single Hall-effect sensor method for brushless DC (BLDC) motor drives. The signal from the Hall-effect sensor is used to generate a number of pseudo Hall signals via a proposed speed-position estimator. The pseudo signals are then employed to control switching logic of a voltage source inverter (VSI). The effectiveness of the single Hall sensor method is examined on the unconventional 160° strategy, and on conventional 120°, 150° and 180° strategies with promising results. The paper presents a detailed comparison of the twelve-step unsymmetrical 160° commutation strategy with six-step voltage space vector that is used in conventional 120° and 180° strategies, and twelve-step symmetrical voltage space vector that is used in 150° strategy. Simulation results are validated via experimental measurements on a laboratory set-up using a real time dSPACE control environment, a representative BLDC motor prototype, a VSI and associated control components. [ABSTRACT FROM AUTHOR]

This paper presents a simple pulse width modulation algorithm for control of an ultracapacitor based energy storage system used for source and load support applications. As opposed to dual loop control philosophy that is widely used for backup applications, this paper presents a simple single loop current control that is only useful for controlling the ultracapacitor based DC/DC converters used in source and load support applications. The proposed PWM blocking method necessitates the DC/DC converter to operate in five states and takes into consideration the essential operational limits associated with the ultracapacitors. The performance of the proposed algorithm is verified experimentally using a 24 V laboratory prototype setup. Further, the shortcomings of dual loop control when applied to source and load support applications are demonstrated. [ABSTRACT FROM AUTHOR]