Search

Beryllium copper alloys are the ideal materials to fabricate the supporting parts owing to their excellent physical and chemical properties. Many high aspect ratio micro-holes are often required to realize the special missions. However, they were not easily fabricated by the traditional machining methods owing to the materials' mechanical strength. Here, we presented a high efficiency method for drilling high aspect ratio micro-holes on C17200 beryllium copper alloy by combining deionized water based micro-EDM and in situ PMEDM with boron carbide additives. The machining parameters were systematically investigated and optimized to realize the ever high aspect ratio of 23.26 at the holes' diameter of 215 μm. The surface quality of the micro-hole was improved further by in-situ PMEDM, which was demonstrated by the decreasing of surface roughness (Ra) from 2.65 μm to 0.92 μm. Our method will open an avenue to fabricate high aspect ratio micro-holes on C17200 with high efficiency. [ABSTRACT FROM AUTHOR]

Beryllium copper alloys known as high-reliability engineered materials are widely used in many engineering fields. Micro-electrical discharge machining (micro-EDM) provides a safely and effectively machining process to machine beryllium copper alloys regardless of their toxicity and mechanical strength. During micro-EDM, the higher material removal rate and the lower electrode wear rate are observed when deionized water is used as a dielectric fluid. However, there are many stray-current corrosion pits on the end surface of holes which directly affect the performance and life span of parts. In this study, the method of auxiliary electrode was used to suppress the effects of stray-current corrosion on the end surfaces of holes on C17200 beryllium copper alloy. The end surfaces of holes were protected by sacrificing the auxiliary electrode. The feasibility of micro-EDM with an auxiliary electrode was verified by an experiment of a hole machined with half coved by the auxiliary electrode and the others without. The effects of the thickness of the auxiliary electrode on end surface quality and machining time were studied. The effects of the auxiliary electrode to suppress stray-current corrosion on C17200 beryllium copper alloy were proved under diffident pulse currents and pulse widths. Machining time and electrode wear were investigated. The results show that the electrode wear is scarcely affected by the auxiliary electrode. However, the machining time is slightly increased when the pulse current is lower than 0.55 A, and the pulse width is shorter than 20 μs. Beyond that level, the effect of the auxiliary electrode on machining time is not obvious. The end surface quality decreases when the pulse width is longer than 20 μs. In addition, the results also show that, when the thickness of the auxiliary electrode is 60 μm, a value of 0.34 A pulse current and 20 μs pulse width could be considered as ideal parameters for C17200 beryllium copper alloy machined by micro-EDM with an auxiliary electrode in deionized water. Furthermore, it is confirmed that the auxiliary electrode can be easily fixed on different radii of curvature surface and effectively protect the end surface of micro-holes from stray-current corrosion. [ABSTRACT FROM AUTHOR]

C f -ZrB 2 -SiC is a new composite material with excellent properties for making the next-generation aerospace component. This material is extremely difficult to removal by mechanical machining, and there is a lack of research on feasible secondary processing methods of this composite at present. Micro-EDM is not limited by material hardness, so it is very suitable for machining this material. In this paper, the Material removal mechanisms and processing characteristics of C f -ZrB 2 -SiC by micro-EDM is analyzed. The removal mechanism of composite materials is explored though the discharge crater morphology, and the single-discharge experiments of each phase materials with different medium and different energies are also carried out as a reference. Electrical discharge milling experiments of C f -ZrB 2 -SiC are performed to explore the medium on processing index, and found that the best surface quality and maximum processing efficiency can be realized in kerosene. An experiment with four factors (pulse width, voltage, peak current, capacitance) and three indexes (surface roughness, MRR, TWR) is designed to analyze the C f -ZrB 2 -SiC process characteristics of micro-EDM and the response surface diagram and second-order regression equation are obtained. Milling the C f -ZrB 2 -SiC by electrical discharge according to the optimal combination of surface roughness parameters deduced above, the as-machined surface is analyzed including the surface morphology by SEM, element content by EDS and the surface phase by XRD. The feasibility and advantages of micro-EDM on machining C f -ZrB 2 -SiC are prove. [ABSTRACT FROM AUTHOR]

Micro-electro discharge milling (micro-ED-milling) with simply shaped electrode is highly regarded as a capable approach of machining 3D micro-structure because of its special machining mechanism and the variety of machinable materials. However, a specific CAD/CAM system is needed for generating tool path and related machining process. Due to nature of machining mode and tool electrode geometry, some vestige always remains on the machined surface during ED-milling of 3D structure especially on the complex surface which cannot be expressed with normal equations. To solve the problems of residual vestige, a slicing strategy for micro-ED-milling is proposed. The way of the tool path generation and the algorithm for smoother surface are studied systemically. Meanwhile, with the way of isoparametric interpolation, the machined freeform surfaces of lamination are significantly improved. As a result, some typical 3D structures are machined for verification, including an embossment of a human face within a circular area of 1 mm in diameter. [Copyright &y& Elsevier]

An integrated method of micro-milling and micro electrical discharge machining (EDM) is proposed for micro-structures array manufacture in this paper. In order to obtain micro-cavity array with high accuracy and consistency, in situ machining on the same coordinate system ensures the positioning precision. After studying micro-milling graphite, the effect of parameters on the machining accuracy is found. Further, suitable mode is chosen for high-dimensional consistency and good surface quality array electrodes according to comparison of one-by-one and layer-by-layer milling tool trajectory. Workpiece lifting control is used to strengthen the debris clear; then, it is verified beneficial of lifting through flow simulation and adding discrete particles. In order to solve poor precision of the micro-cavity contour caused by electrode wear, a multi-step machining by group electrodes is proposed, rough machining for material removal and finishing machining for trimming. Finally, a micro-cavity with clear edge, small fillets, and high shape accuracy is obtained. This method improves the machining performance of the array micro-structures and shows good prospects in micro-fabrication. [ABSTRACT FROM AUTHOR]