Search

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

In recent years, very high frequency (VHF) converter has attracted much attention. However, with rich parasitic parameters and complex resonance links, there are some great difficulties to the modeling of such systems. Taking the on-off controlled VHF resonant boost converter as an example, this paper presents an accurate modeling and analysis method that considers multiple parasitic parameters. First, the closed-loop VHF converter system is divided into a main network and a parasitic oscillation network. Then, based on the operation analysis, an equivalent circuit model characterized by a time-varying input voltage source and two variable duty-cycle controlled switches is proposed. It worth noting that both the time-varying input and the controlled switches take into account the influences of the parameters. Furthermore, the periodic approximate analytical solution of the output voltage in the on stage is obtained by using the equivalent small parameter method to the proposed circuit model. And then combining the solution of the parasitic oscillation network and on-off state switching conditions, the steady-state waveform of output voltage can be obtained quickly. Finally, a prototype with operating frequency of 21.44 MHz is built to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant switching cell model to analyze and design the single-ended resonant dc–dc converters. The single-ended zero-voltage switching (ZVS) converters such as the Class E converter are efficient for megahertz switching because they feature low turn-on and turn-off switching losses. Also, they use only a ground-referenced switch, allowing a simple gate drive circuit. In this paper, we investigate the single-ended resonant converter with the small input inductance, whereas the conventional Class E converter has a large input inductance. The main contribution of this paper is to propose the resonant switching cell as an analytic model that simplifies the analysis and the design of the resonant dc–dc converters. Furthermore, this paper presents the design method of the resonant switching cell model for minimizing the resonant current magnitude and conduction loss while the converter maintains ZVS property. The experimental results from a 10-MHz GaN-based prototype demonstrate the feasibility and effectiveness of the analysis and design based on the proposed resonant switching cell model. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

First harmonic analysis (FHA) is arguably the most widely used analytical technique for wireless power transfer (WPT) circuits due to its simplicity. Although FHA can provide closed-form solutions, the existence of rectifier diode forward voltage drop and higher order harmonics, especially the second and third harmonics at variable duty cycle operation, can significantly deteriorate its accuracy. This paper presents an accurate and efficient method called enhanced multiple harmonic analysis (eMHA) for the optimal design and optimal control of WPT systems. The eMHA method considers the nature of nonlinear rectification networks under nonsinusoidal current and reexamines the concept of the equivalent load. As a result, the rectified WPT system is transformed into a series of linear systems with complex load impedances. The steady-state electric quantities can be then explicitly calculated. This enables eMHA to seamlessly work with numerical optimization algorithms to facilitate the automated design and optimization of WPT systems. An example of optimal design and optimal control of a 10 W WPT system is demonstrated. The results obtained by eMHA and FHA are also compared. A prototype of the designed circuit was constructed. The accuracy and effectiveness of eMHA are verified by experimental measurements. This paper is accompanied by a MATLAB-based analytical tool with a graphical user interface demonstrating the effects of circuit variables on electrical quantities and waveforms. [ABSTRACT FROM AUTHOR]

A new single stage three-phase ac–dc converter with four switches and galvanic isolation is proposed in this paper. The new converter is simple and uses fewer switches than previously proposed ac–dc converters of the same type. It is a bridgeless converter that can operate with continuous input current and with any pulsewidth modulated method suitable for a standard three-phase six-switch voltage source rectifier. In this paper, the operation, control, analysis, and design of the proposed converter are explained and its features are discussed. Experimental results obtained from a prototype that confirm the feasibility of the converter are presented as well. [ABSTRACT FROM AUTHOR]

The paper confirms that removing antiparallel silicon carbide (SiC) Schottky barrier diodes (SBDs) from SiC-based inverters offers positive effects without critical impact on inverter loss and electromagnetic interference (EMI) issues, moreover, the removal of SBDs reduces the inverter losses in many cases and noise emissions. This conclusion leads to the possibility to improve the power densities by removing SBDs. However, the removal of SBDs may cause some disadvantages such as an increase of the reverse conduction loss and influence of the body diode recovery phenomenon. Therefore, a comprehensive investigation of these advantages and disadvantages is necessary. In this paper, design criteria are proposed to clarify the conditions in which SiC-based inverters without SBDs have advantages over those with SBDs from the viewpoint of losses. On the other hand, to achieve the removal of SBDs, it is also necessary to confirm that removing SBDs does not cause severe EMI issues. The paper confirms that switching noises are reduced by the removal of SBDs; this is due to the larger damping effect of the SiC mosfets without SBDs than that of SiC mosfets with SBDs. The validity of the theoretical analyses and design criteria is confirmed with comprehensive experimental results. [ABSTRACT FROM AUTHOR]

In this paper, an overload and short-circuit protection method is proposed for voltage source inverter-based uninterruptible power supply (UPS) system. In order to achieve high reliability and availability of the UPS, short circuit and overload protection scheme are necessary. When overload or short circuit happens, using the proposed control method, the amplitude of the output current can be limited to a constant value, which can be set by the customer to avoid the destruction of the power converter, and to obtain a faster recovery performance as well. The detailed principle of the proposed protection method is discussed in this paper. It mainly contains three parts in the control diagram for current limit, first is the anti-windup in the voltage and current controllers, then the feedforward of the capacitor voltage to the current control loop, the last is the fast reset of the resonant part of the current controller when overcurrent happens. The procedure of developing the control method is also presented in the paper. Experimental results on a commercial UPS system are presented to verify the effectiveness of the control method. [ABSTRACT FROM AUTHOR]

This paper presents a balancing algorithm for the so-called Director Switch, a controlled, reverse conducting, self-powered, high-voltage switch, using series-connected insulated gate bipolar transistors (IGBTs). This is a key component on two new voltage-source, high-voltage direct current (HVDC) converter topologies. These, which promise efficiency, cost, and size reductions, are an alternate arm converter and a series bridge converter. One of the main design challenges of the director switch is how to supply the IGBT gate drivers, and other auxiliary electronics while overcoming the high-voltage insulation barrier to ground level. In this paper, this is achieved by using the energy stored in a capacitive clamp snubber circuit, which also helps with the overvoltage mitigation during rare hard-switching events. However, the clamp capacitor and by proxy the IGBT voltages become highly unbalanced during operation, compromising the integrity of the switch. This paper presents a balancing strategy that consists in applying a controlled delay in the switching of the IGBT levels, in a way that forces a voltage balance on all the switch levels. The paper explains the unbalance. Then, the balancing strategy is explained and validated on simulation and on a high-voltage experimental rig, on switches comprising two and three series-connected IGBTs, respectively. [ABSTRACT FROM AUTHOR]

In the paper by Patra et al., a single-inductor multiple-output switcher was presented to produce buck, boost, and inverted outputs simultaneously. Unfortunately, this study showed some unexpected mistakes, especially in state-space equations and in the calculation of output voltages. The objective of this note was to provide correct analysis and rectify the errors in this paper. Some tables and equations have been modified that were present in the initial draft of this paper. The obtained parameters in this work could be an effective supplement and extension for the original work in the paper by Patra et al. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

An electrical transient model (ETM) of insulated-gate bipolar transistor (IGBT)-diode switching cell is developed by coupling a temperature-dependent IGBT model with power loss model. The nonlinear behavior of IGBT and the reverse recovery characteristic of the diode are considered in this model to simulate the transient switching waveforms. Based on the transient waveforms of ETM under various operating conditions, the power loss estimation method (PLEM) for IGBT is developed. In addition to traditional modeling techniques that only uses ideal switch, this paper uses the model to replicate the power loss behaviors of semiconductor devices in circuit simulation by looking up tables. The proposed ETM is simulated in PSCAD/EMTDC with nanosecond time step, whereas the overall system application can be simulated with conventional time step in range of microsecond. By this way, the model can promise reasonable accuracy as well as an acceptable fast solving speed. The proposed ETM and PLEM have been implemented in PSCAD/EMTDC simulator and validated by experimental results using a double pulse test bench and boost converter test platform. [ABSTRACT FROM AUTHOR]

Improving the power density of a power converter has many benefits for systems integration. Aspects such as thermal management, weight, conformation to mounting locations, and the footprint of the converter all become critical factors as systems continue to scale down in size. The flying capacitor multilevel converter topology is of interest because it has characteristics which contribute to high power density. This paper presents a quasi-square-wave zero-voltage switching (ZVS) multilevel dc–dc converter. ZVS greatly reduces switching losses and enables high-frequency operation of the converter. A hardware prototype is implemented, built on a flexible polyimide substrate circuit board. Experimental results show a peak system efficiency above 98.1%, an effective switching frequency of up to 3 MHz, and a power output of 250 W. [ABSTRACT FROM AUTHOR]

In order to increase the efficiency of modern microprocessor power supplies used in data centers, 380-V dc power distribution systems have been attracting attention due to their high efficiency and high reliability. This paper presents an innovative single-stage approach for 380-V voltage regulator modules (VRMs) based on a quasi-resonant multilevel topology constant on-time operation. The proposed topology inherently integrates the multiphase approach, providing fast phase shedding and flat high-efficiency curves even at light-load conditions. This is a unique advantage, which is not possible to establish in the two-stage approach, which is very important in server architectures, and where high efficiency is required even at light-load conditions. This paper analyzes the circuit topology and proposes a control architecture for fast transient response, including current-sharing capabilities. The digital controller has been implemented in 0.16- $\mu$ m lithography together with a digital pulsewidth modulation with a 195-ps resolution and a 40-MS/s 7-bit analog-to-digital converter. Experimental results show an efficiency of 93% for a 120-A 380–1.8-V VRM power supply. [ABSTRACT FROM AUTHOR]

This paper proposes a fifth-order resonant immittance network based dual-active-bridge (DAB) converter and an optimal modulation method that will ensure high-efficiency operation of the converter under wide-range variations in voltage ratio and output power level. The proposed modulation method is based on the concept of total power loss minimization, where a loss model is developed and an optimization algorithm is formulated to compute the optimal set of internal and external phase shift parameters that will lead to the maximum efficiency for a given set of operating parameters including voltage ratio and output power level. It is found that to maintain high-efficiency operation under wide-range variations in voltage ratio and output power level, the DAB converter is required to switch between different operation modes and neither soft-switching operation nor unity-power-factor operation is able to achieve wide-range high efficiency performance when used alone. The importance of $reconfigurability$ of operation mode for achieving wide-range high efficiency performance is clearly illustrated in this paper. [ABSTRACT FROM AUTHOR]

In this paper, two simple control methods are proposed for improving direct torque control (DTC) with a constant frequency torque controller (CFTC-DTC) in induction machines. The CFTC-DTC was initially introduced to reduce torque ripple and achieve constant switching frequency in inverters. However, when compared to the original DTC, the CFTC-DTC algorithm suffers from slow torque dynamic response owing to the selection of zero-voltage vectors during torque transient. In addition, when the motor operates at low speed, flux droop occurs at sector transitions, which leads to undesirable current distortions. The problem of flux droop occurs because of short-duty voltage cycles and small radial voltage components at low speeds. This paper has two main contributions—to eliminate zero-voltage vectors during torque dynamics in order to establish a fast torque response in the transient state, and to minimize the flux droop at the sector transitions by applying another triangular carrier and modifying the torque output in order to increase the duty voltage cycles at low motor speeds. A detailed analysis of the problems and proposed methods is presented. Experimental results are provided to validate the effectiveness of both proposed methods. [ABSTRACT FROM AUTHOR]

Various methods have been presented in the past to emulate the electrical behavior of modular multilevel converters (MMCs). To meet the demands for the reliability aspect study of MMCs, this paper proposes a viable setup to emulate the thermal behavior and to investigate its feasibility for reliability testing and thermal model validation of the power modules in the MMC. The proposed mission profile emulator has three distinctive features: 1) capable of emulating and measuring the thermal stresses of power modules; 2) capable of implementing practical switching profile as a full-scale MMC; and 3) having significantly reduced requirement for dc power supply compared to existing setups used for electrical studies. Theoretical discussions, and simulations as well as the experimental results are presented to demonstrate the capability of the mission profile emulator both electrically and thermally. Moreover, this paper is accompanied by a video demonstrating how to measure the junction temperature of the power devices using the optical fiber and the thermal camera. [ABSTRACT FROM AUTHOR]

In this paper, a new dc–dc high voltage gain converter with low-voltage stresses on switches and diodes is proposed. Even though, in the topology of the proposed converter there are not any coupled inductors and transformer utilized, the voltage conversion ratio of the proposed converter is considerable in comparison to its conventional types. Also, two switches of the proposed converter provide longer charge time for two inductors which make the proposed converter capable of providing high voltage gain without preselecting extremely large duty cycles. In addition, the number of power circuit components of the proposed structure are few and the voltage stresses on semiconductor elements are low. In this paper, theoretical analysis of the proposed converter for each operating mode is presented and the voltage gain, voltage and average current stresses of elements, maximum input current ripple, efficiency and equations of critical inductances are calculated. Moreover, to verify the capability of the proposed converter, it is comprehensively compared with other similar recently presented high voltage gain boost converters. Finally, an approximately 12 V/380 V and 520-W prototype of the proposed converter is implemented in laboratory to demonstrate its practical performance, then, the experimental results reconfirm each other and theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper investigates a Vienna rectifier as a charger for series-connected battery packs. Focusing on carrier-based pulsewidth modulation (CBPWM), the ripple current flowing through the neutral point (NP) results in the voltage oscillation if the loads are resistive. To reduce the ripple of average NP current with mitigated distortion under balanced and unbalanced dc-link voltages conditions, a novel CBPWM with segmented component injection scheme (SCIS) is proposed in this paper. After dc component injection, continuous intervals for optimized component injection and clamping intervals for compensation component injection are identified. Optimized components are calculated originally based on unbalanced factor to make the average NP current zero-size in one switching period. Moreover, unique compensation components generate suitable NP current to shape the sinusoidal input currents according to the circuit analysis. In consequence, the SCIS not only keeps the input current with low-harmonic distortion, but also minimizes the oscillation of dc-link voltage under balanced and unbalanced conditions. In addition, the value of the NP current during the clamping intervals is analyzed under various operating conditions. The effectiveness and the performance of the proposed SCIS are verified by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

Switching behavior analysis is an indispensable step for evaluating the steady-state performance of a bidirectional dc–dc converter and a prerequisite for soft-switching modulation design. For dual-bridge series resonant dc–dc converters (DBSRCs), the commonly used fundamental harmonic approximation (FHA) does not usually provide predictions accurate enough for reliable analysis and design. This paper discloses the exact closed-form solution for the zero-voltage switching (ZVS) operation conditions of DBSRCs for the most general case, in which all modulation quantities—i.e., phase shift, duty cycles, and switching frequency—are included. The proposed approach relies on a geometrical analysis of the converter state-plane trajectory, and allows us to analytically predict the ZVS or hard-switching state of any switch and for any given converter operating point. By inherently capturing the effects of all tank harmonics, the model disclosed in this paper shows higher accuracy than the conventional FHA-based approach, and translates into a practical tool for ZVS prediction and optimization at the converter design stage. Based on the derived analytical results, switching behavior of DBSRCs with minimum rms current trajectory (MCT) modulation is investigated, and an effective design choice of resonant-to-switching frequency ratio is presented, which contributes to reduced switching losses and enhanced efficiency. Furthermore, a variable frequency modulation scheme is formulated, achieving ZVS operation of all transistors over a wide input/output voltage range and efficiency improvement versus MCT technique. The analysis and conclusions are validated via extensive experimental tests on a 700 W DBSRC prototype. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

This paper presents two high-voltage direct-current circuit breakers that have the capability of interrupting a short-circuit current within several milliseconds. They consist of a current-limit inductor, a current-control inductor, one or two mechanical switches, and a multilevel converter with phase-shifted-carrier pulsewidth modulation. The two breakers can commutate an almost zero current from the main branch to the auxiliary branch. This paper proposes an original breaker with low-voltage and high-voltage mechanical switches connected in series, followed by a simplified breaker with a single high-voltage mechanical switch. Finally, this paper includes experimental verification by two slightly different downscaled breakers rated at 300 Vdc and 150 Adc, as well as confirmation of an actual original breaker by circuit simulation using the “PSCAD/EMTDC” software package. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency single-phase T-type boundary conduction mode (BCM) microinverter. The conventional full-bridge BCM microinverter has achieved zero voltage switching (ZVS) and thereby improved the efficiency, but it suffers from high switching losses under light load conditions. The proposed T-type BCM microinverter reserves ZVS and uses a multilevel technique to further decrease the switching losses. The BCM operation with multilevel technique will have too low switching frequency when the grid voltage approaches half of the dc link voltage. To solve this problem, this paper adopts a third operation mode for the T-type switching leg to maintain the switching frequency above a minimum value. The corresponding mode transitions are also detailed to ensure a smooth operation. Because of the turn-offdelay of the freewheeling transistor, the actual lower current boundary deviates from the programmed one, which will distort output current. To address this issue, this paper also proposes a boundary compensation method. A prototype has been built for performance verification, which can test both full-bridge and T-type topology. Compared with the full-bridge BCM microinverter, the proposed T-type BCM microinverter has a higher efficiency over the whole load range. [ABSTRACT FROM AUTHOR]

This paper presents nonlinear optimization-based position and speed estimation scheme for IPMSM drives with arbitrary signal injection generated by inherent switching ripples associated with finite control set model predictive control (FCSMPC). The existing standard sensorless techniques are not suitable for FCSMPC which applies voltage vectors directly to an electrical machine without a modulator. The proposed method optimizes the nonlinear cost function derived from the standard IPMSM model with respect to position and speed at every sampling interval. This method can be applied to any type of signal injection and, hence, an ideal candidate for sensorless FCSMPC. In this method, the signal injection is needed only to generate persistent excitation to maintain the observability at low speeds. A strong persistent excitation is always present with FCSMPC except at standstill where the control applies null vector when the reference currents are zero. This situation is overcome in this paper by introducing a small negative $d$ -axis current at standstill. Thus, the proposed method can estimate the position and speed over a wide speed range starting from standstill to the rated speed without a changeover or additional signal injection. This paper also presents detailed convergence analysis and proposes a compensator for standstill operation that prevents converging to saddle and symmetrical solutions, and therefore, also eliminates the well-known ambiguity of $\pi$ rad in position estimation. The performance of the proposed sensorless scheme is experimentally verified for a wide range of operating conditions. [ABSTRACT FROM AUTHOR]

This paper discusses dynamic behavior of a dual-active-bridge (DAB) dc–dc converter. Conventional phase-shift control methods for the DAB converter may cause dc offsets in both inductor current and transformer magnetizing current in transient states. The dc offset in the inductor current would introduce an excessive peak current through the switching devices. The dc offset in the magnetizing current may induce magnetic-flux saturation. Conventional methods simultaneously turn on and off the diagonal switches in each H-bridge converter and produce a square-wave voltage with a 50% duty ratio. In contrast, the proposed method in this paper independently controls each switch to modify the duty ratio in transient states. This paper clearly derives the requirements of each switch to eliminate the dc offsets in both currents with a settling time shorter than half the switching period. Experimental results using a 5-kW 20-kHz system verify the validity of the proposed control method, which is effective not only in a single step change, but also in a continuous change in the phase-shift reference. [ABSTRACT FROM AUTHOR]

This paper presents two novel measurement methods to characterize silicon carbide (SiC) MOSFET devices. The resulting data are utilized to significantly improve the extraction of a custom device model that can now accurately reproduce device switching behavior. First, we consider the $I_{\text{d}}- V_{\text{ds}}$ output characteristics of power devices such as SiC transistors. These are typically measured using traditional curve tracers, but the characterization of the high-voltage and high-current (HVHC) region is very challenging because of device power compliance and self-heating. In this paper, we introduce a measurement technique that overcomes self-heating and derives the HVHC region from switching waveforms. The switching transient characteristics of devices are used to determine drain current $(I_{\text{d}})$ as a function of drain–source voltage $(V_{\text{ds}})$ in the HVHC range. Second, we consider another challenging characterization area: measurement of nonlinear capacitances when device is turned on. These capacitance characteristics of on-state devices are important for correcting disagreements between simulations and measurements in turn-off switching transient waveforms and cannot be measured using a conventional capacitance-voltage meter. We introduce S-parameter measurements as an effective method to obtain the capacitance characteristics of both off-state devices and on-state devices. These novel measurement techniques have been applied to the modeling of a SiC device. The extracted device model, a modified version of the popular Angelov−GaN high-electron-mobility transistor model, shows significant improvement in terms of the accuracy of switching waveforms of devices over a wide range of operating conditions. [ABSTRACT FROM AUTHOR]

Isolated, zero-voltage-switching dc–dc converter topologies represent attractive solutions in the continuous run toward higher switching frequencies, allowing more compact power supplies. Among them, the asymmetrical half-bridge flyback converter represents an interesting option, featuring simple duty-cycle control at constant switching frequency, as opposed to the popular LLC converter. The majority of papers dealing with this topology consider an approximated voltage gain similar to that of an isolated buck converter operating in continuous conduction mode, i.e., proportional to the duty cycle and, practically, load independent. On the contrary, the true voltage gain is nonmonotonic at high duty-cycle values. Anytime the converter is designed for a resonant operation, as is advisable to eliminate any reverse recovery problem of the rectifier diode, the voltage gain not only increases, but also becomes a function of the switching frequency. This article investigates the converter's voltage gain in detail, deriving a theoretical framework capable of capturing its real behavior and dependencies. The proposed analytical model has been verified through simulations as well as experimental measurements taken on a 160-W prototype working at 400 kHz. [ABSTRACT FROM AUTHOR]

Renewable energy generations have been attracting sustained attentions in academic and industry. Current-fed-isolated-bidirectional dc/dc converters (CF-IBDCs) are widely adopted in low-voltage high-current applications such as solar photovoltaic fuel cell with energy storage. This paper gives an overview and a comprehensive comparative evaluation of CF-IBDCs. The active clamped, dual half-bridge, L-L type dual active bridge, resonant-type, naturally clamped, and other type topologies of CF-IBDCs are investigated, analyzed, and compared regarding their circuit topological structures, operation characteristics, modulation methods, and soft-switching technologies. In addition, component cost models and loss models of converters are deduced and presented. On this basis, quantitative and comprehensive performance comparison of seven typical CF-IBDC topologies selected from each type is conducted in terms of costs, losses, weight, volume, and power density for the given system specifications and design constraints. Finally, the application range of different CF-IBDCs and future trend are presented to encourage further development. [ABSTRACT FROM AUTHOR]

This paper proposes a new approach for the capacitor balancing of a dual three-level T-type converter based on silicon carbide discrete semiconductors. This study is performed while the converter feeds an open-end induction motor. The model predictive control (MPC) scheme is developed to balance the dc-link capacitors and to control the machine torque simultaneously. The proposed technique for MPC reduces the number of redundant switching states that are used in computations without affecting the operating voltage vectors. This reduces the computational time substantially. In addition, the proposed control strategy mitigates the weighting factor tuning problem of capacitor balancing in addition to the conventional MPC cost function. MATLAB simulation results for the proposed drive system under different case studies are presented. Hardware experimental setup for the proposed converter is built, tested, and verified. A comparison between experimental and simulation results is presented. It is observed that the theoretical as well as the experimental results are in full agreement. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology combining reconfigurability and hybridization is presented. Reconfigurability allows the proposed converter to operate in three different operating modes, yielding a wide range of step-up conversion ratios. The combination of two charge-pump cells and an inductor allows to reduce the average inductor current if compared to a standard equivalent boost converter. A prototype with integrated MOS, drivers, and logic but external passives was built. Experimental results show that with $\mathbf {f_{s} }=\text{300}\,$ kHz, $\mathbf {V_{in} = \text{6}}\,$ V, and $\mathbf {I_o = \text{70}}\,$ mA, the converter can cover conversion ratios in the range from $\text {2.5}$ to $\text {10}$ , with a maximum output voltage equal to $\text {60}\,$ V. Peak efficiency is $\text {91}$ %. When the output current is increased to $\text {100}\,$ mA peak efficiency is $\text {92.8}$ %. [ABSTRACT FROM AUTHOR]

This paper investigates the influence of active zero vector pulsewidth modulation (AZPWM-1) and space vector pulsewidth modulation (SVPWM) on the design of passive common-mode (CM) attenuation methods to reduce CM current and shaft voltage in inverter-fed V/f-controlled induction motor drives. The passive CM attenuation methods examined here are the CM choke, the CM electromagnetic interference (EMI) filter, and the CM transformer. The attenuation requirement of AZPWM-1 and SVPWM is identified to design the passive CM choke and EMI filter. Based on the attenuation requirement, the design guidelines are revisited for SVPWM, and design rules are proposed for AZPWM-1. However, the CM transformer is designed based on the step change in magnitude of CM voltage of both the pulsewidth modulations (PWMs). The limitations in design, regarding switching frequency and component size for each case, are also established. It is shown that to have a similar attenuation in the considered two PWM cases, AZPWM-1 requires smaller passive components compared to SVPWM. The proposed design guidelines are substantiated with experimental results on a 1.1-kW induction motor drive. [ABSTRACT FROM AUTHOR]

Multilevel converters are widely applied in medium voltage (MV) drive systems due to the attractive features, such as the ability to use devices with lower voltage ratings, high equivalent switching frequency, etc. Recently, a multilevel topology, named seven-level hybrid clamped (7L-HC), is proposed for MV drives. It has a competitive number of devices, showing the potential to build low-cost 7L converters. However, to ensure the wide frequency range operation and power quality of MV drives, its dc-link capacitors and floating capacitors must be controlled properly with balanced voltages. In this paper, an active voltage balancing method is proposed for the 7L-HC converter. This method can effectively balance all the capacitor voltages under a wide frequency range. The method is embedded in the PWM procedure without modifying the control strategies. Simulation and experimental results are provided to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a voltage multiplier topology that is a hybrid between a Cockcroft–Walton multiplier and a Dickson charge pump. The Cockcroft–Walton structure exhibits significant output voltage drop under load as the number of multiplier stage increases. This is because all coupling capacitors are connected in series. Dickson charge pump mitigates this issue by connecting all capacitors in parallel. But this solution comes at the expense of large capacitor voltage stress at the last multiplier stage. The proposed hybrid structure arranges some capacitors in parallel and others in series, thereby achieving low output voltage drop and low capacitor voltage stress at the same time. We develop a model that predicts hybrid multiplier's performance and validates it experimentally. We also demonstrate a 60–2.25 kV dc–dc converter based on a 16-stage hybrid voltage multiplier which achieves a voltage gain of 12.8 while keeping the highest capacitor voltage stress to 660 V. [ABSTRACT FROM AUTHOR]

The power efficiency and weight of present point-of-load (POL) dc–dc converters for drone applications are often compromised because they suffer from large switching losses at continuous conduction mode for heavy loads and excessive hardware overheads at discontinuous conduction mode for light loads. This paper presents a boundary conduction mode (BCM) control scheme for POL converters embodying a single operation mode. This is achieved by means of a hysteresis voltage controller to turn on/off the output power stage when necessary. The proposed BCM control scheme achieves high power efficiency (≥91.2%) over a wide load range (5 mA–1 A) by means of fully soft switching. Specifically, a hysteretic current controller is proposed to realize ZCS, and an adaptive dead time controller is proposed to realize ZVS. Further, the proposed BCM control scheme requires a small output inductor (0.82 μH) by means of designing the customizable peak inductor current. To verify the proposed BCM control scheme, we realize a BCM-based POL converter that features an input voltage range of 5–16 V, output voltage range of 2.5–8 V, switching frequency of 1.5 MHz, peak power efficiency of 96.8%, and ≤35 mV output voltage undershoot/overshoot for 1-A load step. When being benchmarked against state-of-the-art counterparts, the proposed design features the lowest voltage undershoot/overshoot, the highest switching frequency, ∼5.7× smaller inductor, and ∼11% higher power efficiency at light loads. [ABSTRACT FROM AUTHOR]

A matrix converter (MC) with model predictive control based on the source reactive power control usually fails to show sinusoidal source currents. The analysis presented in this paper shows that this common combination of a converter and control has the inherent inability to suppress some harmonics in the source currents, even with additional passive or active damping control. Direct source current control can be implemented to give sinusoidal source currents and intrinsic active damping. However, the issue of steady-state error in output currents then arises, as the MC topology does not allow of the independent control of source and output currents. Therefore, feedback control of load active power is proposed to address this issue without degrading the fast dynamic performance. Benefiting from the direct source current control, a simplified implementation is also proposed to decrease the number of candidate switching states from 27 to 5, which significantly reduces the computational burden. Experimental results have verified the theoretical analysis and the effectiveness of the proposed control scheme. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual active bridge (DAB)-based high-frequency-isolated dc–ac converter topology suitable for photovoltaic microinverter applications. The circuit configuration on the secondary sides of the employed three-winding transformer results in high-frequency current injection into each of the switch nodes, thereby making zero-voltage-switching (ZVS) operation of the devices possible. The topology achieves this functionality while using the same number of devices as conventional two-stage and single-stage high-frequency-link or DAB-based solutions. Furthermore, following a control-oriented power pulsation decoupling strategy involving dynamic variation of phase shift, twice line-frequency energy buffering can be handled on the high-voltage secondary side, thereby resulting in reduction in decoupling capacitance requirement. The working principle of the circuit and the associated control scheme is described followed by a detailed ZVS analysis. Simulation studies and experimental tests on a 310 W prototype verify circuit operation and exhibit efficiency improvements compared to a similar two-stage solution. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

With the conventional secondary phase-shifted (PS) control, a semidual-active-bridge (S-DAB) dc–dc converter suffers from low efficiency at light load in buck mode due to hard switching and high tank current. In order to avoid this phenomenon and extend soft-switching range, a hybrid control including the primary pulsewidth modulation plus secondary phase-shifted (PWM+PS) is proposed in this paper. Under the proposed hybrid control, all steady-state operation modes with distinctive features are identified and analyzed. Based on the operation range, power characteristics and switching behaviors in each mode, a minimum peak current control route is developed, which can enable the converter to work with low tank current and soft switching over the whole load range. A lab-scale S-DAB converter is implemented to validate the theoretical analysis, and experimental results reveal that the higher efficiency can be achieved using the proposed control route. [ABSTRACT FROM AUTHOR]

Battery energy storage system based on the modular multilevel converter (MMC-BESS) is able to realize the decentralized management of battery packs, which is suitable for the retired battery utilization to improve the efficiency of battery recycling. With multiple submodules (SM), the corresponding SM fault ride-through method is mandatory to improve operational reliability. This paper proposes a redistributed pulsewidth modulation method for MMC-BESS to ride-through the SM fault through employing the simple logic operation, which could avoid the unexpected carrier shift under various modulation indexes induced by the SM fault or grid voltage rise. MATLAB simulations and experimental results are presented to verify the performance of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a pulsed power modulator with a new structure that utilizes the reverse recovery characteristics of diodes to achieve an effective pull-down circuit configuration. The proposed configuration for active pull-down applicable to negative pulsed power applications with a high-voltage direct switching method is implemented by adding a diode to the pulse discharging path of the modulator, instead of using a pull-down resistor. The diode is forward-biased while an output pulse voltage is applied to the load. When the pulse voltage applied to the load is removed, the residual energy in the load is quickly discharged through the reverse recovery path of the diode so that the pull-down function of the pulsed power supply system is efficiently performed. The operating principle of the proposed system is described, and each operating mode is analyzed in detail. In addition, the feasibility of the proposed system configuration is examined through various simulation results. Finally, it is proven that the proposed system can be used effectively in pulsed power application fields through a practical experiment in plasma source ion implantation applications. [ABSTRACT FROM AUTHOR]

The measurement of fast voltage and current transients of Silicon Carbide (SiC) devices requires high bandwidth (BW) probes. Commercially available voltage and current probes can be expensive, and, in addition, the delay introduced by them must be compensated to achieve a proper time alignment (de-skew). Determining this de-skewing value is not a trivial task. In this paper, a simple and affordable measurement method is presented for the simultaneous measurement of the voltage and current transients of SiC devices. The voltage is measured by means of a high BW RC attenuator, while the current is estimated from the voltage drop in the stray inductance of the switching loop. Since both voltages are measured with two equal and matched high BW passive voltage probes, there is no need to apply any de-skew. This is one of the most important advantages of the method. The presented method is experimentally evaluated and used for the estimation of energy switching losses in the tested SiC-mosfet. [ABSTRACT FROM AUTHOR]

This paper describes the design, robustness analysis, and implementation of a zero average dynamics sliding mode control (ZAD–SMC) for a multiphase step-down converter. The ZAD–SMC operates at fixed switching frequency and allows to implement an interleaving technique providing current-ripple cancellation at the converter output. Moreover, the proposed control structure, which is based on a master–slave strategy, includes an equalization technique guaranteeing current sharing among the phases and avoiding undesirable power unbalance. Additionally, a stability analysis considering unmatched losses in the converter phases shows that the design provides asymptotic stability for the overall load range. The controllers are implemented in an FPGA, and all the expected features, such as fast transient response, robustness, fixed switching frequency, interleaving, and current equalization are sustained by the experimental results obtained from using a 1.5-kW prototype. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) strings consisting of multiple panels suffer from partial shading or characteristic mismatch issues, such as a significant reduction in power yield. Various kinds of differential power processing (DPP) converters have been developed to prevent the negative impacts of substring-level partial shading. For panel-level applications, however, conventional DPP converters face a variety of challenges, such as impaired extendibility and increased voltage stress of circuit elements. This paper proposes a switched capacitor converter (SCC)-based modular DPP architecture. Modules, each containing series-connected panels with a panel-level DPP converter, are connected through a switchless module-level DPP converter, and PV panel characteristics are unified at module- and panel-levels. The number of panels in each module is fixed, while the number of modules can be arbitrarily extended without redesigning DPP converters, hence offering good modularity. In addition, since voltage stresses of capacitors in the proposed architecture can be reduced lower than half the module voltages, the proposed DPP system realizes all-ceramic-capacitor SCC circuit by properly determining the module voltages. A prototype for eight panels, which were grouped into two modules, was built, and laboratory and field tests were performed. The experimental results demonstrated the enhanced power yield from the partially shaded PV string. [ABSTRACT FROM AUTHOR]

Finite control set model predictive control (FCS-MPC) calculates torque and flux tracking errors via a cost function that is used for selecting the optimal vector. Compared with field oriented control, FCS-MPC has the merit of a faster dynamic performance because it eliminates both pulsewidth modulation and inner proportion-integration controllers. However, the weighting factor for modifying torque and flux terms must be tuned in accordance with varying operating conditions; this is an area in which further research is needed. In this paper, a parallel predictive torque control (PPTC) with predefined constraints is proposed as a solution for this problem. The PPTC method optimizes torque and flux terms simultaneously, and switching-state candidates are then selected in an adaptive mechanism. The key feature is that torque and flux tracking errors are constrained within the initial boundaries. The proposed PPTC is compared with the state-of-the-art predictive torque control (PTC) method. Both simulation and experimental results confirm that the proposed method, which has no weighting factor, achieves an even better dynamic performance and robustness than the conventional PTC. [ABSTRACT FROM AUTHOR]

Nine-switch converter (NSC) has been presented as a dual-output converter with common frequency (CF) or different frequency (DF) operation modes. This paper proposes a novel space-vector modulation (SVM) method for the NSC that supports both the CF and DF modes. This method is based on the simplification of the space-vector diagram of NSC into that of six-switch converter, and the SVM method for NSC can be done like conventional SSC. The proposed voltage vector selection method without using common logical xor operation and the calculation method for dwelling times of voltage vectors are described in detail. In addition, the modulation indices for two ac terminals of NSC have been analyzed deeply, and the derived fitting equations can guide engineering application. The performance of the proposed SVM is verified by the simulation and experimental results, and the low total harmonic distortions and harmonic components for phase currents prove the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper employs a single-phase-shift modulated dual-active-bridge converter (DABC), and establishes a small-signal model, which involves its voltage transformation ratio. Then, through a voltage transformation ratio feedback loop, which is feedforward compensated by the port voltages and currents, closed-loop control of the transformation ratio of the DABC is realized. The proposed controller can make the DABC operate in constant transformation ratio mode, and act as an ideal dc transformer in an active dc distribution network. Based on the bidirectional voltage support capability of the proposed dc transformer, the different buses of an active dc distribution network can mutually provide voltage support for each other. Besides, the proposed dc transformer can realize the normalized decentralized power coordination between the energy storage systems at different buses of the active dc distribution network. The feasibility of the proposed dc transformer is verified by several hardware-in-loop tests. [ABSTRACT FROM AUTHOR]

This paper proposes the design of gray wolf optimizer (GWO) algorithm-based fractional order proportional integral (FOPI) controller for power factor correction (PFC) using interleaved dc–dc single ended primary inductance converter converter with improved performance characteristics such as speed, accuracy, and stability. The detailed analysis and modeling of the proposed converter are presented. The optimal parameters of FOPI controller are obtained using GWO algorithm to improve the speed of response of the system. FOPI controller provides better performance in terms of robustness and stability since it has one more adjustable parameter than the conventional proportional integral (PI) controller. The cascade control strategy is implemented for the proposed converter with GWO-based FOPI controller as inner current and outer voltage controllers for PFC and load voltage regulation. The performance characteristics of the proposed system are analyzed and compared with conventional and other optimization techniques using MATLAB/Simulink software. A prototype of the proposed converter controlled by TMS320C2000 microcontroller for an output power of 200 W is tested and validated with the simulation results. The proposed system is used for powering devices like robots in critical applications such as military, space craft, etc., where stability, speed, and accuracy are major concerns. [ABSTRACT FROM AUTHOR]