Search

Inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub‐0.60 eV bandgaps grown on InP and GaAs are presented. Threading dislocation densities are 1.3 ± 0.6 × 106 and 8.9 ± 1.7 × 106 cm−2 on InP and GaAs, respectively. The devices generate open‐circuit voltages of 0.386 and 0.383 V, respectively, under irradiance producing a short‐circuit current density of ≈10 A cm−2, yielding bandgap‐voltage offsets of 0.20 and 0.21 V. Power and broadband reflectance measurements are used to estimate thermophotovoltaic (TPV) efficiency. The InP‐based cell is estimated to yield 1.09 W cm−2 at 1100 °C versus 0.92 W cm−2 for the GaAs‐based cell, with efficiencies of 16.8 versus 9.2%. The efficiencies of both devices are limited by sub‐bandgap absorption, with power weighted sub‐bandgap reflectances of 81% and 58%, respectively, the majority of which is assumed to occur in the graded buffers. The 1100 °C TPV efficiencies are estimated to increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application to laser power conversion in the 2.0–2.3 µm atmospheric window. Peak laser power converter efficiencies of 36.8% and 32.5% are estimated under 2.0 µm irradiances of 1.86 and 2.81 W cm−2, respectively. [ABSTRACT FROM AUTHOR]

In this work, the effect of a varying spectral irradiance and top cell bandgap on the energy harvesting efficiency of two‐terminal (2T) and four‐terminal (4T) perovskite//silicon tandem solar cells under outdoor operating conditions is investigated. For the comparison, an optoelectronic model employing a 1 year outdoor data set for a 4T mechanical stacked gallium arsenide (GaAs) on crystalline silicon (Si) tandem device is first validated. Then, the verified model is used to simulate perovskite//silicon tandem devices with a varying perovskite top cell bandgap for a location in Golden, Colorado, USA. A spectral binning method to efficiently reduce and improve the visualization of the 1 min‐resolved environmental data while maintaining the simulation accuracy is introduced. The findings reveal that, for a device that is current matched under standard testing conditions, the annual spectral deviation reduces the energy harvesting efficiency by only 2%rel. When additional realistic losses for the 4T are taken into account, 2T devices are shown to have an energy‐harvesting efficiency that is at parity or higher. Deviations in the top cell bandgap are more than 0.1 eV from current matching result in a reduced energy harvesting efficiency of more than 5%rel for the 2T tandem device. [ABSTRACT FROM AUTHOR]

In order to realize a clean energy society by using renewable energies, high-performance solar cells are a very attractive proposition. The development of high-performance solar cells offers a promising pathway toward achieving high power per unit cost for many applications. As state-of-the-art of single-junction solar cells are approaching the Shockley–Queisser limit of 32%–33%, an important strategy to raise the efficiency of solar cells further is stacking solar cell materials with different bandgaps to absorb different colors of the solar spectrum. The III–V semiconductor materials provide a relatively convenient system for fabricating multi-junction solar cells providing semiconductor materials that effectively span the solar spectrum as demonstrated by world record efficiencies (39.2% under one-sun and 47.1% under concentration) for six-junction solar cells. This success has inspired attempts to achieve the same with other materials like perovskites for which lower manufacturing costs may be achieved. Recently, Si multi-junction solar cells such as III–V/Si, II–VI/Si, chalcopyrite/Si, and perovskite/Si have become popular and are getting closer to economic competitiveness. Here, we discuss the perspectives of multi-junction solar cells from the viewpoint of efficiency and low-cost potential based on scientific and technological arguments and possible market applications. In addition, this article provides a brief overview of recent developments with respect to III–V multi-junction solar cells, III–V/Si, II–VI/Si, perovskite/Si tandem solar cells, and some new ideas including so-called 3rd generation concepts. [ABSTRACT FROM AUTHOR]

Radical reduction of III–V device costs requires a multifaceted approach attacking both growth and substrate costs. Implementing device removal and substrate reuse provides an opportunity for substrate cost reduction. Controlled spalling allows removal of thin devices from the expensive substrate; however, the fracture‐based process currently generates surfaces with significant morphological changes compared to polished wafers. 49 single junction devices are fabricated across the spalled surface of full 50 mm germanium wafers without chemo‐mechanical polishing before epitaxial growth. Device defects are identified and related to morphological spalling defects—arrest lines, gull wings, and river lines—and their impact on cell performance using physical and functional characterization techniques. River line defects have the most consistent and detrimental effect on cell performance. Devices achieve a single junction efficiency above 23% and open‐circuit voltage of 1.01 V, demonstrating that spalled germanium does not need to be returned to a pristine, polished state to achieve high‐quality device performance. [ABSTRACT FROM AUTHOR]

The analytical drift-diffusion formalism is able to accurately simulate a wide range of solar cell architectures and was recently extended to include those with back surface reflectors. However, as solar cells approach the limits of material quality, photon recycling effects become increasingly important in predicting the behavior of these cells. In particular, the minority carrier diffusion length is significantly affected by the photon recycling, with consequences for the solar cell performance. In this paper, we outline an approach to account for photon recycling in the analytical Hovel model and compare analytical model predictions to GaAs-based experimental devices operating close to the fundamental efficiency limit. [ABSTRACT FROM AUTHOR]

High-efficiency, four-terminal tandem solar cells composed of thin GaAs films mechanically stacked onto interdigitated back contact silicon solar cells with a glass interlayer are demonstrated. The optimal thickness of the absorber layer of a rear heterojunction GaAs subcell for use in four terminal tandem solar cells was studied. GaAs top cells with absorber layer thicknesses of 1.5, 1.9, 2.3, 2.8, and 3.5 μm were fabricated on glass and mechanically stacked onto interdigitated back-contact Si bottom cells. All tandem cells were found to have efficiencies above 30% under the AM1.5 G spectrum demonstrating a relatively weak sensitivity to thickness in the four-terminal configuration. We found the 2.8 μm absorber layer cell to have the highest top cell and tandem cell efficiency at 26.38% and 32.57%, respectively. Optical modeling with transfer matrix method for the planar top cell and Lambertian light trapping in the textured Si subcell, along with drift-diffusion Hovel equations, were used to show photon recycling enhancement to the effective diffusion length and VOC of the top cell as a result of the low-index glass interlayer. [ABSTRACT FROM AUTHOR]

High‐efficiency solar cells are essential for high‐density terrestrial applications, as well as space and potentially vehicle applications. The optimum bandgap for the terrestrial spectrum lies beyond the absorption range of a traditional dual junction GaInP/GaAs cell, with the bottom GaAs cell having higher bandgap energy than necessary. Lower energy bandgaps can be achieved with multiple quantum wells (QWs), but such a pathway requires advanced management of the epitaxial growth conditions in order to be useful. Strain‐balanced GaAsP/GaInAs QWs are incorporated into a single junction GaAs solar cell and a dual junction GaInP/GaAs solar cell, leading to 27.2% efficiency in the single junction device and a one‐sun record 32.9% efficiency in the tandem device. Good carrier collection and low non‐radiative recombination are observed in the cells with up to 80 QWs. The GaAs cells employ a rear‐heterojunction architecture to boost the open‐circuit voltage to over 1.04 V in the quantum well device, despite the large number of QWs. [ABSTRACT FROM AUTHOR]

The optical and electrical properties of many III-V alloys change with the degree of CuPt atomic ordering, which is very sensitive to growth conditions. The bulk ordered alloy is elongated along the normal to the ordered planes, and is asymmetrically strained when coherent to a cubic substrate. Here, we demonstrate in situ measurement of the anisotropic strain due to ordering using two-dimensional wafer curvature. The measurement is sensitive to bulk anisotropies, and so is complementary to other in situ measurements that are sensitive to surface anisotropies. Using ab initio calculations, we determine a maximum strain anisotropy of 0.27% between [110] and [110] when perfectly ordered single-variant GaInP2 is coherent to a (001) cubic substrate. We relate the in situ measurement of strain anisotropy on various GaInP2 samples to ex situ measurements of the order parameter to validate the measurement and confirm the capability to predict material properties. The measurement monitors change in ordering during growth, useful for quickly determining the growth condition dependence of ordering or monitoring order-disorder transitions. More generally, this measurement technique could, in principle, be used to monitor phase changes in any epitaxial system for which the strain anisotropy of the two phases differs. [ABSTRACT FROM AUTHOR]

Inverted metamorphic (IMM) multijunction solar cells represent a promising material platform for ultrahigh efficiency photovoltaic systems (UHPVs) with a clear pathway to beyond 50% efficiency. The conventional device processing of IMM solar cells, however, typically involves wafer bonding of a centimeter‐scale die and destructive substrate removal, thereby imposing severe restrictions in achievable cell size, type of module substrate, spatial layout, as well as cost effectiveness. Here, we report material design and fabrication strategies for microscale triple‐junction IMM (3J IMM) Ga0.51In0.49P/GaAs/In0.26Ga0.74As solar cells that can overcome these difficulties. Specialized schemes of delineation and undercut etching enable the defect‐free release of microscale IMM solar cells and printed assemblies on a glass substrate in a manner that preserves the growth substrate, where efficiencies of 27.3% and 33.9% are demonstrated at simulated AM1.5D one‐ and 351 sun illumination, respectively. A composite carrier substrate where released IMM microcells are formed in fully functional, print‐ready configurations allows high‐throughput transfer printing of individual IMM microcells in a programmable spatial layout on versatile choices of module substrate, all desired for CPV applications. [ABSTRACT FROM AUTHOR]

Currently, most solar cells are designed for and evaluated under standard spectra intended to represent typical spectral conditions. However, no single spectrum can capture the spectral variability needed for annual energy production (AEP) calculations, and this shortcoming becomes more significant for series-connected multijunction cells as the number of junctions increases. For this reason, AEP calculations are often performed on very detailed yearlong sets of data, but these pose 2 inherent challenges: (1) These data sets comprise thousands of data points, which appear as a scattered cloud of data when plotted against typical parameters and are hence cumbersome to classify and compare, and (2) large sets of spectra bring with them a corresponding increase in computation or measurement time. Here, we show how a large spectral set can be reduced to just a few 'proxy' spectra, which still retain the spectral variability information needed for AEP design and evaluation. The basic 'spectral binning' methods should be extensible to a variety of multijunction device architectures. In this study, as a demonstration, the AEP of a 4-junction device is computed for both a full set of spectra and a reduced proxy set, and the results show excellent agreement for as few as 3 proxy spectra. This enables much faster (and thereby more detailed) calculations and indoor measurements and provides a manageable way to parameterize a spectral set, essentially creating a 'spectral fingerprint,' which should facilitate the understanding and comparison of different sites. [ABSTRACT FROM AUTHOR]

This paper re-examines the impact of atmospheric absorption bands on series-connected multijunction cell design, motivated by the numerous local efficiency maxima that appear as the number of junctions is increased. Some of the local maxima are related to the bottom subcell bandgap and are already well understood: As the bottom subcell bandgap is varied, a local efficiency maximum is produced wherever the bottom cell bandgap crosses an atmospheric absorption band. The optimal cell designs at these local maxima are generally current matched, such that all subcells have nearly the same short-circuit current. Here, we systematically describe additional local maxima that occur wherever an upper subcell bandgap encounters an atmospheric absorption band. These local maxima are not current matched and become more prevalent as the number of junctions increases, complicating the solution space for five-junction and six-junction designs. A systematic framework for describing this complexity is developed, and implications for numerical convergence are discussed. Copyright © 2017 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

InGaAsP/InGaP quantum well (QW) structures are promising materials for next generation photovoltaic devices because of their tunable bandgap (1.50–1.80 eV) and being aluminum-free. However, the strain-balance limitations have previously limited light absorption in the QW region and constrained the external quantum efficiency (EQE) values beyond the In0.49Ga0.51P band-edge to less than 25%. In this work, we show that implementing a hundred period lattice matched InGaAsP/InGaP superlattice solar cell with more than 65% absorbing InGaAsP well resulted in more than 2× improvement in EQE values than previously reported strain balanced approaches. In addition, processing the devices with a rear optical reflector resulted in strong Fabry-Perot resonance oscillations and the EQE values were highly improved in the vicinity of these peaks, resulting in a short circuit current improvement of 10% relative to devices with a rear optical filter. These enhancements have resulted in an InGaAsP/InGaP superlattice solar cell with improved peak sub-bandgap EQE values exceeding 75% at 700 nm, an improvement in the short circuit current of 26% relative to standard InGaP devices, and an enhanced bandgap-voltage offset (Woc) of 0.4 V. [ABSTRACT FROM AUTHOR]

A novel bonding approach with an interface consisting of a metal and dielectric is developed, and a 'pillar-array' metal topology is proposed for minimal optical and electrical loss at the interface. This enables a fully lattice-matched two-terminal, four-junction device that consists of an inverted top two-junction (2J) cell with 1.85 eV GaInP/1.42 eV GaAs, and an upright lower 2J cell with ~1 eV GaInAsP/0.74 eV GaInAs aimed for concentrator applications. The fabrication process and simulation of the metal topology are discussed along with the results of GaAs/GaInAs 2J and (GaInP + GaAs)/GaInAs three-junction bonded cells. Bonding-related issues are also addressed along with optical coupling across the bonding interface. Copyright © 2014 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

The assumption of superposition or linearity of photocurrent with solar flux is widespread for calculations and measurements of solar cells. The well-known effect of luminescent coupling in multijunction solar cells has also been assumed to be linear with excess current. Here we show significant non-linearities in luminescent coupling in III-V multijunction solar cells and propose a simple model based on competition between radiative and nonradiative processes in the luminescent junction to explain these non-linearities. We demonstrate a technique for accurately measuring the junction photocurrents under a specified reference spectrum, that accounts for and quantifies luminescent coupling effects. [ABSTRACT FROM AUTHOR]

Catalytic interface of semiconductor photoelectrodes is critical for high-performance photoelectrochemical solar water splitting because of its multiple roles in light absorption, electrocatalysis, and corrosion protection. Nevertheless, simultaneously optimizing each of these processes represents a materials conundrum owing to conflicting requirements of materials attributes at the electrode surface. Here we show an approach that can circumvent these challenges by collaboratively exploiting corrosion-resistant surface stoichiometry and structurally-tailored reactive interface. Nanoporous, density-graded surface of 'black' gallium indium phosphide (GaInP2), when combined with ammonium-sulfide-based surface passivation, effectively reduces reflection and surface recombination of photogenerated carriers for high efficiency photocatalysis in the hydrogen evolution half-reaction, but also augments electrochemical durability with lifetime over 124 h via strongly suppressed kinetics of corrosion. Such synergistic control of stoichiometry and structure at the reactive interface provides a practical pathway to concurrently enhance efficiency and durability of semiconductor photoelectrodes without solely relying on the development of new protective materials. Photoelectrochemical water splitting presents an integrated means storing sunlight into fuels, yet high optical losses and corrosion limit device performance. Here, authors boost absorption and durability in gallium-indium phosphide photocathodes via a sulfurized and nanostructured protection layer. [ABSTRACT FROM AUTHOR]

Photovoltaic conversion efficiencies of 32.6 ± 1.4% under the AM1.5 G173 global spectrum, and 35.5% ± 1.2% at 38-suns concentration under the direct spectrum, are demonstrated for a monolithic, dual-junction 1.7/1.1 eV solar cell. The tandem cell consists of a 1.7 eV GaInAsP top-junction grown lattice-matched to a GaAs substrate, followed by a metamorphic 1.1 eV GaInAs junction grown on a transparent, compositionally graded metamorphic AlGaInAs buffer. This bandgap combination is much closer to the dual-junction optimum and offers headroom for absolute 3% improvement in efficiency, in comparison to the incumbent lattice-matched GaInP/GaAs (∼1.86/1.41 eV) solar cells. The challenge of growing a high-quality 1.7 eV GaInAsP solar cell is the propensity for phase separation in the GaInAsP alloy. The challenge of lattice-mismatched GaInAs solar cell growth is that it requires minimizing the residual dislocation density during the growth of a transparent compositionally graded buffer to enable efficient metamorphic tandem cell integration. Transmission electron microscopy reveals relatively weak composition fluctuation present in the 1.7 eV GaInAsP alloy, attained through growth control. The threading dislocation density of the GaInAs junction is ∼1 × 106 cm−2, as determined from cathodoluminescence measurements, highlighting the quality of the graded buffer. These material advances have enabled the performance of both junctions to reach over 80% of their Shockley-Queisser limiting efficiencies, with both the subcells demonstrating a bandgap-voltage offset, WOC (=Eg/q-VOC), of ∼0.39 V. [ABSTRACT FROM AUTHOR]