Search

Biotemplating technique allows the synthesis of catalysts, recreating the sophisticated structure of nature templates. In this work, some biotemplated TiO2 semiconductors were synthesized using Olea europaea leaves as templates. Then, g-C3N4 was coupled to materials to later incorporate Pt on the surface or as dopant in the structure to evaluate the efficiency of the solids in two photocatalytic applications to valorize biomass: hydrogen production through glycerol photoreforming, and photoacetalization of cinnamaldehyde with 1,2-propanediol. In glycerol photoreforming, the presence of Pt (superficial or dopant) enhanced hydrogen production, being Pt@AOLCN (a heterojunction containing biotemplated TiO2, g-C3N4, and Pt) the system that exhibited the highest efficiency (3053.4 µmol·gcat−1·h−1). For photoacetalization, while Pt reduced cinnamaldehyde conversion, it improved selectivity when incorporated on TiO2. Notably, carbon nitride (CN) exhibited the highest yield after 16 h of testing. The study emphasizes the importance of tailoring catalyst selection to specific reactions, as efficiency is closely tied to the structural and chemical properties of the materials. These findings contribute to the development of efficient photocatalysts for sustainable biomass valorization processes. [ABSTRACT FROM AUTHOR]

Pt-TiO2 systems are the most widely used photocatalysts in the production of green hydrogen from glycerol photoreforming. To incorporate metals on the surface of materials, photodeposition is the most used method because it employs mild conditions. However, despite its use, there are some parameters that have not been deeply studied, such as the appropriate metal loading and the method itself, to obtain a better dispersion of Pt. In this work, six Pt-TiO2 catalysts were synthesized by a classical photodeposition method employing UV radiation. The studied Pt wt.% range was 0.15–0.60 wt.%, being incorporated in one step or in subsequent ones. HRTEM analyses showed that both methods allowed a homogeneous distribution of Pt, and in both, the particle size was around 2.3–3.6 nm, increasing with metal loading. The photocatalytic activity of materials was tested in glycerol photoreforming under UV radiation, and the 0.45 wt.% Pt-containing solid that had been synthesized in one step was the one that allowed the highest hydrogen production. This might suggest that around 0.40% is the appropriate metal loading for hydrogen production under these conditions and that incorporating the desired metal percentage in one step is the most efficient method in terms of energy and time savings. [ABSTRACT FROM AUTHOR]

Several biochars were synthesized from olive stones and used as supports for TiO2, as an active semiconductor, and Pt as a co-catalyst (Pt/TiO2-PyCF and Pt/TiO2-AC). A third carbon-supported photocatalyst was prepared from commercial mesoporous carbon (Pt/TiO2-MCF). Moreover, a Pt/TiO2 solid based on Evonik P25 was used as a reference. The biochars used as supports transferred, to a large extent, their physical and chemical properties to the final photocatalysts. The synthesized catalysts were tested for hydrogen production from aqueous glycerol photoreforming. The results indicated that a mesoporous nature and small particle size of the photocatalyst lead to better H2 production. The analysis of the operational reaction conditions revealed that the H2 evolution rate was not proportional to the mass of the photocatalyst used, since, at high photocatalyst loading, the hydrogen production decreased because of the light scattering and reflection phenomena that caused a reduction in the light penetration depth. When expressed per gram of TiO2, the activity of Pt/TiO2-PyCF is almost 4-times higher than that of Pt/TiO2 (1079 and 273 mmol H2/gTiO2, respectively), which points to the positive effect of an adequate dispersion of a TiO2 phase on a carbonaceous support, forming a highly dispersed and homogeneously distributed titanium dioxide phase. Throughout a 12 h reaction period, the H2 production rate progressively decreases, while the CO2 production rate increases continuously. This behavior is compatible with an initial period when glycerol dehydrogenation to glyceraldehyde and/or dihydroxyacetone and hydrogen predominates, followed by a period in which comparatively slower C-C cleavage reactions begin to occur, thus generating both H2 and CO2. [ABSTRACT FROM AUTHOR]

Hydrogen production is mainly based on the use of fossil fuels, but currently, many alternative routes are being developed, among which the photo-reforming of oxygenated organic compounds stands out. Recently, several studies have been carried out in order to develop new techniques to create bio-inspired TiO2 structures. One of these is 'biotemplating', a process that replicates a biological system in an inorganic TiO2-based structure. In this study, olive by-products—olive leaves—are valorized as a biotemplate for the synthesis of new Fe-TiO2- and Cu-TiO2-based photocatalysts with the aim of improving the replication of the leaf structure and enhancing hydrogen photoproduction. In conclusion, the incorporation of iron and copper decreases the band gap and increases the energetic disorder at the band edges. Moreover, it is verified by SEM and TEM that the metals are not found forming particles but are introduced into the formed TiO2 structure. The accuracy of the internal and external structure replication is improved with the incorporation of Fe in the synthesis, while the incorporation of Cu substantially improves the production of hydrogen, which is multiplied 14 times under UV light and 6 times under sunlight, as compared to a pure TiO2 structure. [ABSTRACT FROM AUTHOR]

Nowadays, biomass is an interesting raw material for chemical industry, and the valorisation of its derivatives becomes in a sustainable alternative against to the depletion of fossil sources necessary for the production of energy, fuels and chemicals. Different organic compounds, such as sugars, polyols, furanics, as well as several acids (i.e. levulinic acid, succinic acid, itaconic acid, 3-hydroxy-propionic acid, among others) can be obtained after a primary treatment of the lignocellulosic-type biomass. These bio-derived molecules can be used as "platform chemicals" for the synthesis of numerous chemical products (i.e. components and additives for fuels, solvents and paintings, new monomers for polymer industry, etc.). In this review, the possibilities of valorisation via novel catalytic processes of some of the most promising biomass(cellulose/hemicellulose)-derived intermediates and platform chemicals for obtaining both conventional and new high added-value chemicals for industry will be assessed, also including cascade-type (or "one-pot") catalytic processes recently developed. [ABSTRACT FROM AUTHOR]

Fatty acids are the major compounds in olive oils, and the determination of their profile is very useful in order for the authentication of the high quality of extra virgin olive oil (EVOO) and the evaluation of its purity and traceability. This work considers the estimations of saturated (SAFA), monounsaturated (MUFA) and polyunsaturated (PUFA) fatty acids obtained by gas chromatography (GC), 13C (carbonyl, C‐16, and aliphatic carbons regions), and 1H NMR spectra. The aim of this paper is to analyze the correlation structure being between the abovementioned fatty acids estimations and some long‐run agroclimatic measurements (temperature, humidity, wind speed and direction, radiation, precipitation, and evapotranspiration), which were downloaded from the official website of the Andalusian Automatic Weather Stations (AWSs). The versatile graphical possibilities of the free software R‐project allow the design of computational programs providing interesting conclusions about the described correlations as a function of month, variety of olive, and protected designation of origin (PDO). The statistically significant correlations could determine relevant agroclimatic information to be included, in a further research, among the explanatory variables in regression models in order to improve the estimation of fatty acid profile of EVOOs, considered as a quality parameter in their authentication. Fatty acids are the major compounds in olive oils and very useful in order to the authentication of the high quality of extra virgin olive oil (EVOO). This paper analyzes the effect of agroclimatic big fata, instead of a meteorological factor, on EVOO fatty acid profile determined by GC and NMR spectra. The power of the free software R‐project and its versatile graphical possibilities allows the design of computational programs providing interesting conclusions about the described correlations as a function of month, variety of olive, and protected designation of origin (PDO). [ABSTRACT FROM AUTHOR]

Extra virgin olive oil (EVOO) is very appreciated by its taste, flavor, and benefits for health, and so, it has a high price of commercialization. This fact makes it necessary to provide reliable and cost‐effective analytical procedures, such as near‐infrared (NIR) spectroscopy, to analyze its traceability and purity, in combination with chemometrics. Fatty acids profile of EVOO, considered as a quality parameter, is estimated, firstly, from NIR data and, secondly, by adding agro‐climatic information. NIR and agro‐climatic data sets are summarized by using principal component analysis (PCA) and treated by both scalar and functional approaches. The corresponding PCA and FPCA are progressively introduced in regression models, whose goodness of fit is evaluated by the dimensionless root‐mean‐square error. In general, SFAs, MUFAs, and PUFAs (and disaggregated fatty acids) estimations are improved by adding agro‐climatic besides NIR information (mainly, temperature or evapotranspiration) and considering a functional point of view for both NIR and agro‐climatic data. [ABSTRACT FROM AUTHOR]

BACKGROUND Fatty acids are the major components in extra virgin olive oil, and they are considered as a quality parameter to its authentication. As fraudulent practices are the most important problem in this sector, fast, reliable and cost‐effective techniques, such as Raman spectroscopy, have been successfully applied, in combination with chemometrics, to determine the fatty acid profile of oils. RESULTS: The huge amount of information provided by Raman spectra is reduced in a few orthogonal components of principal component analysis (PCA). The goodness‐of‐fit of the statistical models including only these PCA factors is considerably increased by introducing dummy variables, associated with the harvest, and some agro‐climatic variables (temperature, humidity, wind speed, radiation, precipitation and evapotranspiration). Many of these additional variables are statistically relevant in models using either the global sample or subsamples of Andalusian provinces or olive varieties. CONCLUSIONS: The regression models using only Raman spectral information are clearly improved by the consideration of harvesting time and agro‐climatic data, a useful result as trade standard applying to olive oils limits values for disaggregated fatty acids to authenticate olive oils. Nevertheless, the effect (or the statistical relevance) of these variables depends on the specific type of fatty acid, geographical region (province) or olive variety. © 2019 Society of Chemical Industry [ABSTRACT FROM AUTHOR]

Two series of catalysts were prepared by sol-gel and microemulsion synthetic procedure (SG and ME, respectively). Each series includes both pure Mg and Zr solids as well as Mg-Zr mixed solids with 25%, 50% and 75% nominal Zr content. The whole set of catalysts was characterized from thermal, structural and surface chemical points of view and subsequently applied to the liquid-phase xylose dehydration to furfural. Reactions were carried out in either a high-pressure autoclave or in an atmospheric pressure multi-reactor under a biphasic (organic/water) reaction mixture. Butan-2-ol and toluene were essayed as organic solvents. Catalysts prepared by microemulsion retained part of the surfactant used in the synthetic procedure, mainly associated with the Zr part of the solid. The MgZr-SG solid presented the highest surface acidity while the Mg3Zr-SG one exhibited the highest surface basicity among mixed systems. Xylose dehydration in the high-pressure system and with toluene/water solvent mixture led to the highest furfural yield. Moreover, the yield of furfural increases with the Zr content of the catalyst. Therefore, the catalysts constituted of pure ZrO2 (especially Zr-SG) are the most suitable to carry out the process under study although MgZr mixed solids could be also suitable for overall processes with additional reaction steps. [ABSTRACT FROM AUTHOR]

The thermochemical processing of biomass is an alternative route for the manufacture of fuel-grade ethanol, in which the catalytic conversion of syngas to ethanol is a key step. The search for novel catalyst formulations, active sites and types of support is of current interest. In this work, the catalytic performance of an Rh/MCM-41 catalyst has been evaluated and compared with a typical Rh/SiO2 catalyst. They have been compared at identical reaction conditions (280 °C and 20 bar), at low syngas conversion (2.8%) and at same metal dispersion (H/Rh = 22%). Under these conditions, the catalysts showed different product selectivities. The differences have been attributed to the concentration of water vapor in the pores of Rh/MCM-41. The concentration of water vapor could promote the water-gas-shift-reaction generating some extra carbon dioxide and hydrogen, which in turn can induce side reactions and change the product selectivity. The extra hydrogen generated could facilitate the hydrogenation of a C2-oxygenated intermediate to ethanol, thus resulting in a higher ethanol selectivity over the Rh/MCM-41 catalyst as compared to the typical Rh/SiO2 catalyst; 24% and 8%, respectively. The catalysts have been characterized, before and after reaction, by N2-physisorption, X-ray photoelectron spectroscopy, X-ray diffraction, H2-chemisorption, transmission electron microscopy and temperature programmed reduction. [ABSTRACT FROM AUTHOR]

In the last few years, researchers have focused their attention on the synthesis of new catalyst structures based on or inspired by nature. Biotemplating involves the transfer of biological structures to inorganic materials through artificial mineralization processes. This approach offers the main advantage of allowing morphological control of the product, as a template with the desired morphology can be pre-determined, as long as it is found in nature. This way, natural evolution through millions of years can provide us with new synthetic pathways to develop some novel functional materials with advantageous properties, such as sophistication, miniaturization, hybridization, hierarchical organization, resistance, and adaptability to the required need. The field of application of these materials is very wide, covering nanomedicine, energy capture and storage, sensors, biocompatible materials, adsorbents, and catalysis. In the latter case, bio-inspired materials can be applied as catalysts requiring different types of active sites (i.e., redox, acidic, basic sites, or a combination of them) to a wide range of processes, including conventional thermal catalysis, photocatalysis, or electrocatalysis, among others. This review aims to cover current experimental studies in the field of biotemplating materials synthesis and their characterization, focusing on their application in heterogeneous catalysis. [ABSTRACT FROM AUTHOR]

A correction to this paper has been published: https://doi.org/10.1007/s11244-021-01438-9 [ABSTRACT FROM AUTHOR]

This article explores the effect of the synthetic method of titanium dioxide (TiO2)/C composites (physical mixture and the water-assisted/unassisted sol-gel method) on their photocatalytic activity for hydrogen production through glycerol photoreforming. The article demonstrates that, apart from a high surface area of carbon and the previous activation of its surface to favor titania incorporation, the appropriate control of titania formation is crucial. In this sense, even though the amount of incorporated titania was limited by the saturation of carbon surface groups (in our case, ca. 10 wt.% TiO2), the sol-gel process without water addition seemed to be the best method, ensuring the formation of small homogeneously-distributed anatase crystals on mesoporous carbon. In this way, a ca. 110-fold increase in catalyst activity compared to Evonik P25 (expressed as hydrogen micromole per grams of titania) was achieved. [ABSTRACT FROM AUTHOR]

Olive leaves (by-product from olive oil production in olive mills) were used as biotemplates to synthesize a titania-based artificial olive leaf (AOL). Scanning electron microscopy (SEM) images of AOL showed the successful replication of trichomes and internal structure channels present in olive leaves. The BET surface area of AOL was 52 m2·g−1. X-ray diffraction (XRD) and Raman spectra revealed that the resulting solid was in the predominantly-anatase crystalline form (7.5 nm average particle size). Moreover, the synthesis led to a red-shift in light absorption as compared to reference anatase (gap energies of 2.98 and 3.2 eV, respectively). The presence of surface defects (as evidenced by X-ray photoelectron spectroscopy, XPS, and electron paramagnetic resonance spectroscopy, EPR) and doping elements (e.g., 1% nitrogen, observed by elemental analysis and XPS) could account for that. AOL was preliminarily tested as a catalyst for hydrogen production through glycerol photoreforming and exhibited an activity 64% higher than reference material Evonik P25 under solar irradiation and 144% greater under ultraviolet radiation (UV). [ABSTRACT FROM AUTHOR]

In the present piece of research, hydrogen production via the photo-reforming of glycerol (a byproduct from biodiesel generation) is studied. Catalysts consisted of titania modified by Ni (0.5% by weight) obtained through deposition–precipitation or impregnation synthetic methods (labelled as Ni-0.5-DP and Ni-0.5-IMP, respectively). Reactions were performed both under UV and solar irradiation. Activity significantly improved in the presence of Ni, especially under solar irradiation. Moreover, pre-reduced solids exhibited higher catalytic activities than untreated solids, despite the "in-situ" reduction of nickel species and the elimination of surface chlorides under reaction conditions (as evidenced by XPS). It is possible that the catalyst pretreatment at 400 °C under hydrogen resulted in some strong metal–support interactions. In summary, the highest hydrogen production value (ca. 2600 micromole H2·g−1) was achieved with pre-reduced Ni-0.5-DP solid using UV light for an irradiation time of 6 h. This value represents a 15.7-fold increase as compared to Evonik P25. [ABSTRACT FROM AUTHOR]

The influence of boron, tungsten and molybdenum modifiers on zirconia-based Pt catalyst was studied for glycerol valorization. Zirconia modified supports were prepared by impregnation of ZrO2 with either boric, silicontungstic or phosphomolybdic acids to obtain supports with enhanced Brönsted acidic properties. The modified supports were subsequently impregnated with chloroplatinic acid to obtain Pt-based catalysts. Pt incorporation resulted in the increase in Lewis acidity of the solids, being more significant for the Pt//W/ZrO2 catalyst. Reduced Pt catalysts were tested for the liquid-phase glycerol hydrogenolysis, observing a synergistic effect between catalyst acid sites and metal function that proved to be crucial in glycerol hydrogenolysis. The Pt//W/ZrO2 catalyst was the most active catalyst in this reaction, being the only leading to 1,3-PDO (45% sel., 160 °C) while Pt//Mo/ZrO2 is the best option for 1,2-PDO (49% sel., 180 °C). Reusability studies carried out for Pt//W/ZrO2 showed that catalytic activity dropped after the first use, remaining constant for the second and subsequent ones. Selectivity to reaction products also changes during reuses. Therefore, the selectivity to 1,2 PDO increases in the first reuse in detriment to the selectivity to n-propanol whereas the selectivity to 1,3-PDO remains constant along the uses. This behavior could be associated to the lixiviation of W species and/or catalyst fouling during reaction runs. [ABSTRACT FROM AUTHOR]

Aldol condensation of furfural and acetone (an important initial step to obtain diesel from biomass) was studied over MgAl mixed oxides. The influence of the utilization of microwaves and/or a surfactant (Pluronic 123) during the synthesis as well as the use of water (either pre-hydrating the solids before catalytic studies or in water/toluene mixtures as the reaction medium) is discussed. The combined use of Pluronic 123 and microwaves led to solids with bigger pore sizes, exhibiting lower basicity and higher acidity than the conventional synthetic method, thus resulting in an increase in the yield of the desired product of condensation, comprising two molecules of furfural and one of acetone (F2Ac). As for the influence of water, re-hydration of the mixed oxides was detrimental to activity, probably as a result of the partial blocking (solvation) of active sites. On the contrary, the increase in water percentage in the reaction medium resulted in higher conversions, though selectivity to F2Ac decreased. The weakening of the C=O bond of furfural in the presence of water as well as the higher solubility of the first condensation product (FAc) in toluene, as compared to water, could account for that. A 44.5% yield of F2Ac (66% conversion) after 16 h was obtained with the most active solid, which maintained the activity for three consecutive reactions. [ABSTRACT FROM AUTHOR]

The Meerwein–Ponndorf–Verley (MPV) reaction is an environmentally-friendly process consisting of the reduction of a carbonyl compound through hydrogen transfer from a secondary alcohol. This work deals with MPV reduction of furfural to furfuryl alcohol on different ZrOx, MgOx, TiOx, and Mg–Ti, as well as Zr–Ti mixed systems. The solids were synthesized through the sol–gel process and subsequently calcined at 200 °C. Characterization was performed using a wide range of techniques: ICP-MS, N2 adsorption-desorption isotherms, EDX, TGA-DTA, XRD, XPS, TEM, TPD of pre-adsorbed pyridine (acidity) and CO2 (basicity), DRIFT of adsorbed pyridine, and methylbutynol (MBOH) test reaction. ZrOx showed the highest conversion and selectivity values, which was attributed to the existence of acid–base pair sites (as evidenced by the MBOH test reaction), whereas the introduction of titanium resulted in the drop of both conversion and selectivity probably due to the increase in Brönsted-type acidity. As for MgOx, it had a predominantly basic character that led to the production of the condensation product of one molecule of furfural and one molecule of acetone, and thus resulted in a lower selectivity to furfuryl alcohol. The TiOx solid was found to be mainly acidic and exhibited both Lewis and Brönsted acid sites. The presence of the latter could account for the lower selectivity to furfuryl alcohol. All in all, these results seemed to suggest that the MPV reaction is favored on Lewis acid sites and especially on acid–base pair sites. The process was accelerated under microwave irradiation. [ABSTRACT FROM AUTHOR]

Argon TIAGO torch plasma in air ambience has been studied to produce the decomposition of ethanol obtaining hydrogen at the plasma exit. Dependence of by-products formed on ethanol flows has been studied. Ethanol molecules were completely decomposed, and an important conversion to hydrogen was obtained. Images of plasma generated in these conditions are presented. [ABSTRACT FROM PUBLISHER]