Search

The application of solar-thermal surfaces for antifrosting and defrosting has emerged as a passive and environmentally friendly approach to mitigate the negative consequences of frost formation, such as structural damage and reduced heat transfer efficiency. However, achieving robust all-day frostphobicity solely through interfacial modification and solar-thermal effects is challenging in practical applications: The thick frost that accumulates at night strongly scatters solar radiation, rendering the solar-thermal coatings ineffective during the daytime. Additionally, these nanostructured coatings are susceptible to wear and tear when exposed to the outdoors for extended periods of time. To address these challenges, we present an innovative frostphobic surface that incorporates V-grooved structures with superhydrophobic solar-thermal layers (VSSs). The out-of-plane gradient structures facilitate spatially regulated vapor diffusion, an enhanced photothermal effect, and robust water repellency. These features not only prevent frost from covering the entire surface overnight, enabling effective solar-thermal defrosting during the daytime, but also protect the surface from deterioration. The combined merits ensure robust all-day frostphobicity and exceptional durability, making the VSS surface promising for practical applications and extending the lifespan in extreme environments.

The bottom contact in perovskite solar cells (PSCs) is easy to cause deep trap states and severe instability issues, especially under maximum power point tracking (MPPT). In this study, sodium gluconate (SG) is employed to disperse tin oxide (SnO 2 ) nanoparticles (NPs) and regulate the interface contact at the buried interface. The SG-SnO 2 electron transfer layer (ETL) enabled the deposition of pinhole-free perovskite films in ambient air and improved interface contact by bridging effect. SG-SnO 2 PSCs achieved an impressive power conversion efficiency (PCE) of 25.34% (certified as 25.17%) with a high open-circuit voltage (V OC ) exceeding 1.19 V. The V OC loss is less than 0.34 V relative to the 1.53 eV bandgap, and the fill factor (FF) loss is only 2.02% due to the improved contact. The SG-SnO 2 PSCs retained around 90% of their initial PCEs after 1000 h operation (T 90 = 1000 h), higher than T 80 = 1000 h for the control SnO 2 PSC. Microstructure analysis revealed that light-induced degradation primarily occurred at the buried holes and grain boundaries and highlighted the importance of bottom-contact engineering., (© 2024 Wiley‐VCH GmbH.)

Rapid hot-carrier/exciton cooling constitutes a major loss channel for photovoltaic efficiency. How to decelerate the hot-carrier/exciton relaxation remains a crux for achieving high-performance photovoltaic devices. Here, we demonstrate slow hot-exciton cooling that can be extended to hundreds of picoseconds in colloidal HgTe quantum dots (QDs). The energy loss rate is 1 order of magnitude smaller than bulk inorganic semiconductors, mediated by phonon bottleneck and interband biexciton Auger recombination (BAR) effects, which are both augmented at reduced QD sizes. The two effects are competitive with the emergence of multiple exciton generation. Intriguingly, BAR dominates even under low excitation fluences with a decrease in interparticle distance. Both experimental evidence and numerical evidence reveal that such efficient BAR derives from the tunneling-mediated interparticle excitonic coupling induced by wave function overlap between neighboring HgTe QDs in films. Thus, our study unveils the potential for realizing efficient hot-carrier/exciton solar cells based on HgTe QDs. Fundamentally, we reveal that the delocalized nature of quantum-confined wave function intensifies BAR. The interparticle excitonic coupling may cast light on the development of next-generation photoelectronic materials, which can retain the size-tunable confinement of colloidal semiconductor QDs while simultaneously maintaining high mobilities and conductivities typical for bulk semiconductor materials.

Producing heterostructures of cesium lead halide perovskites and metal-chalcogenides in the form of colloidal nanocrystals can improve their optical features and stability, and also govern the recombination of charge carriers. Herein, the synthesis of red-emitting CsPbI 3 /ZnSe nanoheterostructures is reported via an in situ hot injection method, which provides the crystallization conditions for both components, subsequently leading to heteroepitaxial growth. Steady-state absorption and photoluminescence studies alongside X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy analysis evidence on a type-I band alignment for CsPbI 3 /ZnSe nanoheterostructures, which exhibit photoluminescence quantum yield of 96% due to the effective passivation of surface defects, and an enhancement in carrier lifetime. Furthermore, the heterostructure growth of ZnSe domains leads to significant improvement in the stability of the CsPbI 3 nanocrystals under ambient conditions and against thermal and UV irradiation stress., (© 2024 The Author(s). Small published by Wiley‐VCH GmbH.)

The exploration of high-performance and low-cost wide-bandgap polymer donors remains critical to achieve high-efficiency nonfullerene organic solar cells (OSCs) beyond current thresholds. Herein, the 1,2,3-benzothiadiazole (iBT), which is an isomer of 2,1,3-benzothiadiazole (BT), is used to design wide-bandgap polymer donor PiBT. The PiBT-based solar cells reach efficiency of 19.0%, which is one of the highest efficiencies in binary OSCs. Systemic studies show that isomerization of BT to iBT can finely regulate the polymers' photoelectric properties including i) increasing the extinction coefficient and photon harvest, ii) downshifting the highest occupied molecular orbital energy levels, iii) improving the coplanarity of polymer backbones, iv) offering good thermodynamic miscibility with acceptors. Consequently, the PiBT:Y6 bulk heterojunction (BHJ) device simultaneously reaches advantageous nanoscale morphology, efficient exciton generation and dissociation, fast charge transportation, and suppressed charge recombination, leading to larger V OC of 0.87 V, higher J SC of 28.2 mA cm -2 , greater fill factor of 77.3%, and thus higher efficiency of 19.0%, while the analog-PBT-based OSCs reach efficiency of only 12.9%. Moreover, the key intermediate iBT can be easily afforded from industry chemicals via two-step procedure. Overall, this contribution highlights that iBT is a promising motif for designing high-performance polymer donors., (© 2024 Wiley‐VCH GmbH.)

Lead-free low-dimensional organic-inorganic metal halides have gained increasing attention in a wide range of applications due to their low toxicity, outstanding optical performance, and structural tunability. In this work, a general method of incorporating organic molecule into sodium antimony bromides is introduced. The 1D Na 3 SbBr 6 (C 2 H 6 OS) 6 and Na 3 SbBr 6 (C 4 H 8 OS) 6 single crystals exhibit bright yellow and orange emission with PL peaks at 610 and 664 nm, and high photoluminescence quantum yields (PLQYs) of 85% and 60%, respectively. These two compounds can be reversibly converted into each other by the removal and addition of the organic components. Their exceptional luminescent performance enables them to be used as solid-state phosphors for the fabrication of yellow and orange down-conversion LEDs. A white LED with a high color rendering index (CRI) of 95 is also fabricated by using Na 3 SbBr 6 (C 2 H 6 OS) 6 as the yellow phosphor. The universality of this method is demonstrated by synthesizing other members of this family with diverse A-groups, including methylammonium (MA) and formamidinium (FA). This work provides an effective strategy for the development of diverse lead-free and high-performance organic-inorganic hybrid materials and indicates these organic-inorganic hybrid compounds are promising luminescent materials for lighting or displays., (© 2024 The Authors. Small Methods published by Wiley‐VCH GmbH.)

Dielectric constant of non-fullerene acceptors plays a critical role in organic solar cells in terms of exciton dissociation and charge recombination. Current acceptors feature a dielectric constant of 3-4, correlating to relatively high recombination loss. We demonstrate that selenium substitution on acceptor central core can effectively modify molecule dielectric constant. The corresponding blend film presents faster hole-transfer of ~5 ps compared to the sulfur-based derivative (~10 ps). However, the blends with Se-acceptor also show faster charge recombination after 100 ps upon optical pumping, which is explained by the relatively disordered stacking of the Se-acceptor. Encouragingly, dispersing the Se-acceptor in an optimized organic solar cell system can interrupt the disordered aggregation while still retain high dielectric constant. With the improved dielectric constant and optimized fibril morphology, the ternary device exhibits an obvious reduction of non-radiative recombination to 0.221 eV and high efficiency of 19.0%. This work unveils heteroatom-substitution induced dielectric constant improvement, and the associated exciton dynamics and morphology manipulation, which finally contributes to better material/device design and improved device performance., (© 2024. The Author(s).)

High-efficiency organic solar cells are often achieved using toxic halogenated solvents and additives that are constrained in organic solar cells industry. Therefore, it is important to develop materials or processing methods that enabled highly efficient organic solar cells processed by halogen free solvents. In this paper, we report an innovative processing method named auxiliary sequential deposition that enables 19%-efficiency organic solar cells processed by halogen free solvents. Our auxiliary sequential deposition method is different from the conventional blend casting or sequential deposition methods in that it involves an additional casting of dithieno[3,2-b:2',3'-d]thiophene between the sequential depositions of the donor (D18-Cl) and acceptor (L8-BO) layers. The auxiliary sequential deposition method enables dramatic performance enhancement from 15% to over 18% compared to the blend casting and sequential deposition methods. Furthermore, by incorporating a branched-chain-engineered acceptor called L8-BO-X, device performance can be boosted to over 19% due to increased intermolecular packing, representing top-tier values for green-solvent processed organic solar cells. Comprehensive morphological and time-resolved characterizations reveal that the superior blend morphology achieved through the auxiliary sequential deposition method promotes charge generation while simultaneously suppressing charge recombination. This research underscores the potential of the auxiliary sequential deposition method for fabricating highly efficient organic solar cells using environmentally friendly solvents., (© 2023. The Author(s).)

Metal halide perovskites have shown outstanding optoelectronic and nonlinear optical properties; yet, to realize wafer-scale high-performance perovskite-integrated photonics, the materials also need to have excellent ambient stability and compatibility with nanofabrication processes. In this work, we introduce Dion-Jacobson (D-J) phase perovskites for photonic device applications. By combining self-assembled monolayer-assisted film growth with thermal pressing, we obtain a series of compact and extremely smooth D-J phase perovskite thin films that exhibit excellent stability during electron-beam lithography, solvent development, and rinse. Combining spectroscopic and morphological characterizations, we further demonstrate how organic spacers can be used to fine-tune the photophysical properties and processability of the perovskite films. The distributed-feedback lasers based on the D-J phase perovskites exhibit a low lasing threshold (5.5 μJ cm -2 pumped with nanosecond laser), record high Q factor (up to 30,000), and excellent stability, with an unencapsulated device demonstrating a T 90 beyond 60 hours in ambient conditions (50% relative humidity).

We investigated the influence of two passivating molecules containing a P═O group on the performance of quasi-2D Dion-Jacobson halide perovskite light-emitting diodes, namely, triphenylphosphine oxide (TPPO) and diphenyl-4-triphenylsilylphenyl phosphine oxide (TSPO1). We found that both passivating molecules lead to increased efficiency compared to control devices, while they had opposite effects on device lifetime, with a decrease observed for TPPO and an increase observed for TSPO1. The two passivating molecules resulted in differences in energy-level alignment, electron injection, film morphology and crystallinity, and ion migration during operation. While TPPO resulted in improved photoluminescence decay times, overall higher maximum external quantum efficiency (EQE) and device lifetime were obtained for TSPO1 compared to TPPO (14.4% vs 12.4% EQE, 341 min vs 42 min T 50 ).

The performance of the blue perovskite light-emitting diodes (PeLEDs) is limited by the low photoluminescence quantum yields (PLQYs) and the unstable emission centers. In this work, we incorporate sodium bromide and acesulfame potassium into a quasi-2D perovskite to control the dimension distribution and promote the PLQYs. Benefiting from the efficient energy cascade channel and passivation, the sky-blue PeLED has an external quantum efficiency of 9.7% and no shift of the electroluminescence center under operation voltages from 4 to 8 V. Moreover, the half lifetime of the devices reaches 325 s, 3.3 times that of control devices without additives. This work provides new insights into enhancing the performance of blue PeLEDs.

Various phosphonic acid based self-assembled monolayers (SAMs) have been commonly used for interface modifications in inverted perovskite solar cells. This typically results in significant enhancement of the hole extraction and consequent increase in the power conversion efficiency. However, the surface coverage and packing density of SAM molecules can vary, depending on the chosen SAM material and underlying oxide layer. In addition, different SAM molecules have diverse effects on the interfacial energy level alignment and perovskite film growth, resulting in complex relationships between surface modification, efficiency, and lifetime. Here we show that ethanolamine surface modification combined with [2-(9 H -carbazol-9-yl)ethyl]phosphonic acid (2PACz) results in significant improvement in device stability compared to devices with 2PACz modification only. The significantly smaller size of ethanolamine enables it to fill any gaps in 2PACz coverage and provide improved interfacial defect passivation, while its different chemical structure enables it to provide complementary effects to 2PACz passivation. Consequently, the perovskite films are more stable under illumination (slower photoinduced segregation), and the devices exhibit significant stability enhancement. Despite similar power conversion efficiencies (PCE) between 2PACz only and combined ethanolamine-2PACz modification (PCE of champion devices ∼21.6-22.0% for rigid and ∼20.2-21.0% for flexible devices), the T 80 lifetime under simulated solar illumination in ambient is improved more than 15 times for both rigid and flexible devices.

Embedding submicrocavities is an effective approach to improve the light out-coupling efficiency (LOCE) for planar perovskite light-emitting diodes (PeLEDs). In this work, we employ phenethylammonium iodide (PEAI) to trigger the Ostwald ripening for the downward recrystallization of perovskite, resulting in spontaneous formation of buried submicrocavities as light output coupler. The simulation suggests the buried submicrocavities can improve the LOCE from 26.8 to 36.2% for near-infrared light. Therefore, PeLED yields peak external quantum efficiency (EQE) increasing from 17.3% at current density of 114 mA cm -2 to 25.5% at current density of 109 mA cm -2 and a radiance increasing from 109 to 487 W sr -1  m -2 with low rolling-off. The turn-on voltage decreased from 1.25 to 1.15 V at 0.1 W sr -1  m -2 . Besides, downward recrystallization process slightly reduces the trap density from 8.90 × 10 15 to 7.27 × 10 15  cm -3 . This work provides a self-assembly method to integrate buried output coupler for boosting the performance of PeLEDs., (© 2023. The Author(s).)

Engineering of quasi-two-dimensional (quasi-2D) tin halide perovskite structures is a promising pathway to achieve high-performance lead-free perovskite solar cells, with recently developed devices demonstrating over 14% efficiency. Despite the significant efficiency improvement over the bulk three-dimensional (3D) tin perovskite solar cells, the precise relationship between structural engineering and electron-hole (exciton) properties is not fully understood. Here, we study exciton properties in high-member quasi-2D tin perovskite (which is dominated by large n phases) and bulk 3D tin perovskite using electroabsorption (EA) spectroscopy. By numerically extracting the changes in polarizability and dipole moment between the excited and ground states, we show that more ordered and delocalized excitons are formed in the high-member quasi-2D film. This result indicates that the high-member quasi-2D tin perovskite film consists of more ordered crystal orientations and reduced defect density, which is in agreement with the over 5-fold increase in exciton lifetime and much improved solar cell efficiency in devices. Our results provide insights on the structure-property relationship of high-performance quasi-2D tin perovskite optoelectronic devices.

Fullerene acceptors typically possess excellent electron-transporting properties and can work as guest components in ternary organic solar cells to enhance the charge extraction and efficiencies. However, conventional fullerene small molecules typically suffer from undesirable segregation and dimerization, thus limiting their applications in organic solar cells. Herein we report the use of a poly(fullerene-alt-xylene) acceptor (PFBO-C12) as guest component enables a significant efficiency increase from 16.9% for binary cells to 18.0% for ternary all-polymer solar cells. Ultrafast optic and optoelectronic studies unveil that PFBO-C12 can facilitate hole transfer and suppress charge recombination. Morphological investigations show that the ternary blends maintain a favorable morphology with high crystallinity and smaller domain size. Meanwhile, the introduction of PFBO-C12 reduces voltage loss and enables all-polymer solar cells with excellent light stability and mechanical durability in flexible devices. This work demonstrates that introducing polyfullerenes as guest components is an effective approach to achieving highly efficient ternary all-polymer solar cells with good stability and mechanical robustness., (© 2023. The Author(s).)

Due to the fast dynamics and re-equilibration of supramolecular self-assembly, bottom-up molecular strategies to fabricate well-defined and controllable multiblock structures are rare. Herein, we propose a new concept for fabrication of fluorescent multiblock microcolumns containing 1 to 7 blocks via hierarchical supramolecular self-assembly based on cucurbit[8]uril (CB[8]), NaBr and an AIEgen guest. Through the complexation between CB[8] and different numbers of AIEgen guests (2, 1, 0), the competitive displacement caused by the binding of the sodium cation to the CB[8] portal, and the reversible assembly of positively charged guests in salt solutions, one-pot hierarchical supramolecular self-assembly is realized. The molecular structure of each block is analyzed by single-crystal X-ray diffraction. The AIEgen enables the self-assembly of multiblocks to be visualized, understood, and regulated., (© 2022 Wiley-VCH GmbH.)

Central π-core engineering of non-fullerene small molecule acceptors (NF-SMAs) is effective in boosting the performance of organic solar cells (OSCs). Especially, selenium (Se) functionalization of NF-SMAs is considered a promising strategy but the structure-performance relationship remains unclear. Here, we synthesize two isomeric alkylphenyl-substituted selenopheno[3,2-b]thiophene-based NF-SMAs named mPh4F-TS and mPh4F-ST with different substitution positions, and contrast them with the thieno[3,2-b]thiophene-based analogue, mPh4F-TT. When placing Se atoms at the outer positions of the π-core, mPh4F-TS shows the most red-shifted absorption and compact molecular stacking. The PM6 : mPh4F-TS devices exhibit excellent absorption, high charge carrier mobility, and reduced energy loss. Consequently, PM6 : mPh4F-TS achieves more balanced photovoltaic parameters and yields an efficiency of 18.05 %, which highlights that precisely manipulating selenium functionalization is a practicable way toward high-efficiency OSCs., (© 2022 Wiley-VCH GmbH.)

Organic radicals are unstable and stable radicals usually display non-luminescent properties. Luminescent radicals possess the all-in-one properties of optoelectronics, electronics, and magnetics. To date, the reported structures of luminescent radicals are limited to triphenylmethyl radical derivatives and their analogues, which are stabilized with extended π-conjugation. Here, we demonstrate the first example of a nonconjugated luminescent radical. In spite of the lack of delocalized π-stabilization, the radical polymer readily emits red luminescence in the solid state. A traditional luminescent quencher, 2,2,6,6-tetramethylpiperidin-1-yl turned into a red chromophore when grafted onto a polymer backbone. Experimental data confirm that the emission is associated with the nitroxide radicals and is also affected by the packing of the polymer. This work discloses a novel class of luminescent radicals and a distinctive pathway for luminescence from open-shell materials.

All-inorganic copper(I)-based metal halides have emerged as promising candidates for the replacement of lead perovskites because of their outstanding optical properties. However, the limited structure tunability prohibits their further exploration of properties including red photoluminescence (PL). Here, we report a series of red-emissive lead-free hybrid organic-inorganic copper halides A 6 (C 4 H 8 OS) 12 [Cu 8 X 13 ][Cu 4 X 4 (OH)(H 2 O)] (ACX-THTO, A = K, Rb, and Cs; X = Cl, Br; THTO = C 4 H 8 OS) with the highest photoluminescence quantum yield (PLQY) of 42%. These compounds possess similar crystal structures, and their emission can be tuned in the spectral range of 676-732 nm by controlling their compositions. Additionally, by removing and adding THTO, the reversible transformation between CsCu 2 Br 3 featuring one-dimensional (1D) chains and Cs 6 (C 4 H 8 OS) 12 [Cu 8 Br 13 ][Cu 4 Br 4 (OH)(H 2 O)] (CCB-THTO) with zero-dimensional (0D) clusters can be realized. We also demonstrate that the incorporation of THTO in the crystal structures instead of dimethyl sulfoxide (DMSO) can significantly enhance the stability and PL of compounds with the same inorganic components.

3D mixed-halide perovskite-based red emitters combine excellent charge-transport characteristics with simple solution processing and good film formation; however, light-emitting diodes (LEDs) based on these emitters cannot yet outperform their nanocrystal counterparts. Here the use of diammonium halides in regulating the formation of mixed bromide-iodide perovskite films is explored. It is found that the diammonium cations preferentially bond to Pb-Br, rather than Pb-I, octahedra, promoting the formation of quasi-2D phases. It is proposed that the perovskite formation is initially dominated by the crystallization of the thermodynamically more favorable 3D phase, but, as the solution gets depleted from the regular A cations, thin shells of amorphous quasi-2D perovskites form. This leads to crystalline perovskite grains with efficiently passivated surfaces and reduced lattice strain. As a result, the diammonium-treated perovskite LEDs demonstrate a record luminance (10745 cd m -2 ) and half-lifetime among 3D perovskite-based red LEDs., (© 2022 Wiley-VCH GmbH.)

Integrating highly efficient photovoltaic (PV) function into light-emitting diodes (LEDs) for multifunctional display is of great significance for compact low-power electronics, but it remains challenging. Herein, it is demonstrated that solution engineered perovskite nanocrystals (PNCs, ≈100 nm) enable efficient electroluminescence (EL) and PV performance within a single device through tailoring the dispersity and interface. It delivers the maximum brightness of 490 W sr -1  m -2 at 2.7 V and 23.2% EL external quantum efficiency, a record value for near-infrared perovskite LED, as well as 15.23% PV efficiency, among the highest value for nanocrystal perovskite solar cells. The PV-EL performance is well in line with the reciprocity relation. These all-solution-processed PV-LED devices open up viable routes to a variety of advanced applications, from touchless interactive screens to energy harvesting displays and data communication., (© 2022 Wiley-VCH GmbH.)

Electron donors and acceptors in organic solar cells (OSCs) shall strike a favorable vertical phase separation that acceptors and donors have sufficient contact and gradient accumulation near the cathodes and anodes, respectively. Random mixing of donors/acceptors at surface will result in charge accumulation and severe recombination for low carrier-mobility organic materials. However, it is challenging to tune the vertical distribution in bulk-heterojunction films as they are usually made from a well-mixed donor/acceptor solution. Here, for the first time, it presents with solid evidence that the commonly used 1-chloronaphthalene (CN) additive can tune the donor/acceptor vertical distribution and establish the mechanism. Different from the previous understanding that ascribed the efficiency enhancement brought by CN to the improved molecular stacking/crystallization, it is revealed that the induced vertical distribution is the dominant factor leading to the significantly increased performance. Importantly, the vertical distribution tunability is effective in various hot nonfullerene OSC systems and creates more channels for the collection of dissociated carriers at corresponding organic/electrode interfaces, which contributes the high efficiency of 18.29%. This study of the material vertical distribution and its correlation with molecular stacking offers methods for additives selection and provides insights for the understanding and construction of high-performance OSCs., (© 2022 Wiley-VCH GmbH.)

Integration of photovoltaic (PV) and electroluminescent (EL) functions and/or units in one device is attractive for new generation optoelectronic devices but it is challenging to achieve highly comprehensive efficiency. Herein, perovskite solar cells (PSCs) are fabricated, assisted by 3-sulfopropyl methacrylate potassium salt (SPM) additive to tackle this issue. SPMs not only induce large grain size during the film formation but also produce a secondary phase of 2D K 2 PbI 4 to passivate the grain boundaries (GBs). In addition, its sulfonic acid group and potassium ion can coordinate to lead ion and fill the interstitial defects, respectively. Thus, SPM reduces the defective states and suppresses nonradiative recombination loss. As a result, planar PSC delivers a power conversion efficiency of ≈22%, with a maximum open-circuit voltage (V oc ) of 1.20 V. The V oc is 94% of the radiative V oc limit (1.28 V), higher than the control device (V oc of 1.12 V). In addition, the reciprocity between PV and EL is also correlated to quantify the energy losses and understand the device physics. When operated as a light-emitting diode, the maximum EL external quantum efficiency (EQE EL ) is up to 12.2% (EQE EL of 10.7% under an injection current of short-circuit photocurrent), thus leading to high-performance PV/EL dual functions., (© 2021 Wiley-VCH GmbH.)

AgBiS 2 nanocrystals are a promising nontoxic alternative to PbS, CsPbI 3 , and CdS quantum dots for solution-fabricated nanocrystal photovoltaics. In this work, we fabricated the first inverted (p-i-n) structure AgBiS 2 nanocrystal solar cells. We selected spray-coated NiO as the hole-transporting material and used PCBM/BCP as the electron-transporting material. Combining transient photocurrent and photovoltage measurements with femtosecond transient absorption spectroscopy, we investigated the charge collection process on metal oxide/AgBiS 2 interfaces and demonstrated that the NiO/AgBiS 2 NC junction in the p-i-n configuration is more efficient for charge carrier collection. The fabricated p-i-n solar cells exhibited a 4.3% power conversion efficiency (PCE), which was higher than that of conventional n-i-p solar cells fabricated using the same sample. Additionally, inverted devices showed an ultrahigh short-circuit current ( J SC ) over 20.7 mA cm -2 and 0.38 V open-circuit voltage ( V OC ), suggesting their potential for further improvements in efficiency and, eventually, for large-scale production.

The deployment of photonic integrated circuits (PICs) necessitates an integration platform that is scalable, high-throughput, cost-effective, and power-efficient. Here we present a monolithic InP on SOI platform to synergize the advantages of two mainstream photonic integration platforms: Si photonics and InP photonics. This monolithic InP/SOI platform is realized through the selective growth of both InP sub-micron wires and large dimension InP membranes on industry-standard (001)-oriented silicon-on-insulator (SOI) wafers. The epitaxial InP is in-plane, dislocation-free, site-controlled, intimately positioned with the Si device layer, and placed right on top of the buried oxide layer to form "InP-on-insulator". These attributes allow for the realization of various photonic functionalities using the epitaxial InP, with efficient light interfacing between the III-V devices and the Si-based waveguides. We exemplify the potential of this InP/SOI platform for integrated photonics through the demonstration of lasers with different cavity designs including subwavelength wires, square cavities, and micro-disks. Our results here mark a critical step forward towards fully-integrated Si-based PICs., (© 2021. The Author(s).)

Considering that the periodic photonic nanostructures are commonly realized by expensive nanofabrication processes and the tunability of structure parameters is limited and complicated, we demonstrate a solution-processed upside-down molding method to fabricate photonic resonators on perovskites with a pattern geometry controllable to a certain extent. This upside-down approach not only reveals the effect of capillary force during the imprinting but also can control the waveguide layer thickness due to the inversion of the perovskite membranes.

Managing the dynamics of spin-triplet electronic states is crucial for achieving high-performance organic photovoltaics. Here we show that the replacement of fullerene with non-fullerene acceptor (NFA) molecules leads to suppression of triplet recombination and thus more efficient charge generation. This indicates that the relaxation of charges to the local triplet exciton state, although energetically allowed, is outcompeted by the thermally activated separation of interfacial charge-transfer excitons (CTEs) in the NFA-based system. By rationalizing our results with Marcus theory, we propose that triplet recombination in the fullerene system is driven by the small energy difference and strong electronic couplings between the CTE state and the lowest-lying triplet exciton state (T 1 ) of fullerene acceptor molecules. In contrast, the large energy difference and small electronic couplings between these states in the NFA-based blends lead to sufficiently slow triplet relaxation rate compared to the charge separation rate (≪10 10 s -1 ), thus preventing triplet recombination.

Cesium-lead halide perovskite nanoparticles are a promising class of luminescent materials for color and efficient displays. However, material stability is the key issue to solve before we can use these materials in modern displays. Encapsulation is one of the most efficient methods that can markedly improve the stability of perovskite nanoparticles against moisture, heat, oxygen, and light. Thus, we urgently need a low-cost, reliable, and device-compatible encapsulation method for the integration of nanomaterials into display devices. Here, we propose a facile encapsulation method to stabilize perovskite nanoparticles in thin polymer porous films. Using porous polymer films, we achieved good photoluminescence stability in the harsh environment of high temperature, high humidity and strong UV illumination. The good UV stability benefitted from the unique optical properties of the porous film. Besides, we observed photoluminescence enhancement of CsPbBr 3 nanoparticle films in a high humidity environment. The stable CsPbBr 3 nanoparticle thin porous film provides high brightness (236 nits) and great color enhancement for LCDs and is characterized by simple fabrication with easy scalability, thus it is very suitable for modern LCDs.

While there has been extensive investigation into modulating quasi-2D perovskite compositions in light-emitting diodes (LEDs) for promoting their electroluminescence, very few reports have studied approaches involving enhancement of the energy transfer between quasi-2D perovskite layers of the film, which plays very important role for achieving high-performance perovskite LEDs (PeLEDs). In this work, a bifunctional ligand of 4-(2-aminoethyl)benzoic acid (ABA) cation is strategically introduced into the perovskite to diminish the weak van der Waals gap between individual perovskite layers for promoting coupled quasi-2D perovskite layers. In particular, the strengthened interaction between coupled quasi-2D perovskite layers favors an efficient energy transfer in the perovskite films. The introduced ABA can also simultaneously passivate the perovskite defects by reducing metallic Pb for less nonradiative recombination loss. Benefiting from the advanced properties of ABA incorporated perovskites, highly efficient blue PeLEDs with external quantum efficiency of 10.11% and a very long operational stability of 81.3 min, among the best performing blue quasi-2D PeLEDs, are achieved. Consequently, this work contributes an effective approach for high-performance and stable blue PeLEDs toward practical applications., (© 2020 Wiley-VCH GmbH.)

Organic solar cells based on non-fullerene acceptors can show high charge generation yields despite near-zero donor-acceptor energy offsets to drive charge separation and overcome the mutual Coulomb attraction between electron and hole. Here, we use time-resolved optical spectroscopy to show that free charges in these systems are generated by thermally activated dissociation of interfacial charge-transfer states that occurs over hundreds of picoseconds at room temperature, three orders of magnitude slower than comparable fullerene-based systems. Upon free electron-hole encounters at later times, both charge-transfer states and emissive excitons are regenerated, thus setting up an equilibrium between excitons, charge-transfer states and free charges. Our results suggest that the formation of long-lived and disorder-free charge-transfer states in these systems enables them to operate closely to quasi-thermodynamic conditions with no requirement for energy offsets to drive interfacial charge separation and achieve suppressed non-radiative recombination.

A major challenge for organic solar cell (OSC) research is how to minimize the tradeoff between voltage loss and charge generation. In early 2019, we reported a non-fullerene acceptor (named Y6) that can simultaneously achieve high external quantum efficiency and low voltage loss for OSC. Here, we use a combination of experimental and theoretical modeling to reveal the structure-property-performance relationships of this state-of-the-art OSC system. We find that the distinctive π-π molecular packing of Y6 not only exists in molecular single crystals but also in thin films. Importantly, such molecular packing leads to (i) the formation of delocalized and emissive excitons that enable small non-radiative voltage loss, and (ii) delocalization of electron wavefunctions at donor/acceptor interfaces that significantly reduces the Coulomb attraction between interfacial electron-hole pairs. These properties are critical in enabling highly efficient charge generation in OSC systems with negligible donor-acceptor energy offset.

The traditional design strategies for highly bright solid-state luminescent materials rely on weakening the intermolecular π-π interactions, which may limit diversity when developing new materials. Herein, we propose a strategy of tuning the molecular packing mode by regioisomerization to regulate the solid-state fluorescence. TBP-e-TPA with a molecular rotor in the end position of a planar core adopts a long-range cofacial packing mode, which in the solid state is almost non-emissive. By shifting molecular rotors to the bay position, the resultant TBP-b-TPA possesses a discrete cross packing mode, giving a quantum yield of 15.6±0.2 %. These results demonstrate the relationship between the solid-state fluorescence efficiency and the molecule's packing mode. Thanks to the good photophysical properties, TBP-b-TPA nanoparticles were used for two-photon deep brain imaging. This molecular design philosophy provides a new way of designing highly bright solid-state fluorophores., (© 2020 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Because of their innate ability to store and then release energy, long-persistent luminescence (LPL) materials have garnered strong research interest in a wide range of multidisciplinary fields, such as biomedical sciences, theranostics, and photonic devices. Although many inorganic LPL systems with afterglow durations of up to hours and days have been reported, organic systems have had difficulties reaching similar timescales. In this work, a design principle based on the successes of inorganic systems to produce an organic LPL (OLPL) system through the use of a strong organic electron trap is proposed. The resulting system generates detectable afterglow for up to 7 h, significantly longer than any other reported OLPL system. The design strategy demonstrates an easy methodology to develop organic long-persistent phosphors, opening the door to new OLPL materials., (© 2020 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Photosensitizers (PSs) with multiple characteristics, including efficient singlet oxygen ( 1 O 2 ) generation, cancer cell-selective accumulation and subsequent mitochondrial localization as well as near-infrared (NIR) excitation and bright NIR emission, are promising candidates for imaging-guided photodynamic therapy (PDT) but rarely concerned. Herein, a simple rational strategy, namely modulation of donor-acceptor (D-A) strength, for molecular engineering of mitochondria-targeting aggregation-induced emission (AIE) PSs with desirable characteristics including highly improved 1 O 2 generation efficiency, NIR emission (736 nm), high specificity to mitochondria, good biocompatibility, high brightness and superior photostability is demonstrated. Impressively, upon light irradiation, the optimal NIR AIE PS (DCQu) can generate 1 O 2 with efficiency much higher than those of commercially available PSs. The excellent two-photon absorption properties of DCQu allow two-photon fluorescence imaging of mitochondria and subsequent two-photon excited PDT. DCQu can selectively differentiate cancer cells from normal cells without the aid of extra targeting ligands. Upon ultralow-power light irradiation at 4.2 mW cm -2 , in situ mitochondrial photodynamic activation to specifically damage cancer cells and efficient in vivo melanoma ablation are demonstrated, suggesting superior potency of the AIE PS in imaging-guided PDT with minimal side effects, which is promising for future precision medicine., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Acrylonitriles with aggregation-induced emission (AIE) characteristics have been found to show promising applications in two-photon biomedical imaging. Generally, elaborate synthetic efforts are required to achieve different acrylonitriles with distinct functionalities. In this work, we first reported the synthesis of two different group-functionalized AIE-active acrylonitriles (TPAT-AN-XF and 2TPAT-AN) obtained simply by mixing the same reactants at different temperatures using a facile and transition metal-free synthetic method. These two AIE luminogens (AIEgens) exhibit unique properties such as bright red emission in the solid state, large Stokes shift, and large two-photon absorption cross section. Water-soluble nanoparticles (NPs) of 2TPAT-AN were prepared by a nanoprecipitation method. In vitro imaging data show that 2TPAT-AN NPs can selectively stain lysosome in live cells. Besides one-photon imaging, remarkable two-photon imaging of live tumor tissues can be achieved with high resolution and deep tissue penetration. 2TPAT-AN NPs show high biocompatibility and are successfully utilized in in vivo long-term imaging of mouse tumors with a high signal-to-noise ratio. Thus, the present work is anticipated to shed light on the preparation of a library of AIE-active functionalized acrylonitriles with intriguing properties for biomedical applications.

Currently, photovoltaic/electroluminescent (PV/EL) perovskite bifunctional devices (PBDs) exhibit poor performance due to defects and interfacial misalignment of the energy band. Interfacial energy-band engineering between the perovskite and hole-transport layer (HTL) is introduced to reduce energy loss, through adding corrosion-free 3,3'-(2,7-dibromo-9H-fluorene-9,9-diyl) bis(n,n-dimethylpropan-1-amine) (FN-Br) into a HTL free of lithium salt. This strategy can turn the n-type surface of perovskite into p-type and thus correct the misalignment to form a well-defined N-I-P heterojunction. The tailored PBD achieves a high PV efficiency of up to 21.54% (certified 20.24%) and 4.3% EL external quantum efficiency. Free of destructive additives, the unencapsulated devices maintain >92% of their initial PV performance for 500 h at maximum power point under standard air mass 1.5G illumination. This strategy can serve as a general guideline to enhance PV and EL performance of perovskite devices while ensuring excellent stability., (© 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Photostability is a particularly important parameter for fluorescence imaging especially long-term dynamic tracking in live samples. However, many organic fluorophores show poor photostability under one-photon and two-photon continuous irradiation. In addition, these traditional fluorophores also suffer from aggregation-caused quenching (ACQ) in aggregate state in insolvable water environment. Therefore, it remains challenging to develop photostable and ACQ-free fluorophores for biological imaging. In this work, we developed two highly photostable aggregation-induced emission luminogens (AIEgens) based on the cyanostilbene core for in vitro and ex vivo bioimaging. These AIEgens named CS-Py + SO 3 - and CS-Py + exhibit near-infrared solid-state emission, large Stokes shift (>180 nm), high fluorescence quantum yield (12.8%-13.7%) and good two-photon absorption cross section (up to 88 GM). CS-Py + SO 3 - and CS-Py + show specific organelle staining with high biocompatibility in membrane and mitochondria in live cells, respectively. In addition, selective two-photon mitochondria visualization in live rat skeletal muscle tissues with deep-tissue penetration (about 100 μm) is successfully realized by using CS-Py + . Furthermore, these AIEgens especially CS-Py + exhibit remarkably high resistance to photobleaching under one-photon and two-photon continuous irradiation. These highly photostable AIEgens could be potentially utilized in visualizing and tracking specific organelle-associated dynamic changes in live systems., (Copyright © 2019. Published by Elsevier Ltd.)

A compact, efficient, and monolithically grown III-V laser source provides an attractive alternative to bonding off-chip lasers for Si photonics research. Although recent demonstrations of microlasers on (001) Si wafers using thick metamorphic buffers are encouraging, scaling down the laser footprint to nanoscale and operating the nanolasers at telecom wavelengths remain significant challenges. Here, we report a monolithically integrated in-plane InP/InGaAs nanolaser array on (001) silicon-on-insulator (SOI) platforms with emission wavelengths covering the entire C band (1.55 μm). Multiple InGaAs quantum wells are embedded in high-quality InP nanoridges by selective-area growth on patterned (001) SOI. Combined with air-cladded InP/Si optical cavities, room-temperature operation at multiple telecom bands is obtained by defining different cavity lengths with lithography. The demonstration of telecom-wavelength monolithic nanolasers on (001) SOI platforms presents an important step towards fully integrated Si photonics circuits.

Multicomponent quasi-two-dimensional perovskites (Q-2DPs) have efficient luminescence and improved stability, which are highly desirable for light-emitting diode and perovskite solar cell (PSC). However, the lack of radiative recombination at room temperature is still not well understood and the performance of PSC is not good enough as well. The open-circuit voltage ( V OC ) is even lower than that of three-dimensional (3D) PSC with a narrower band gap. In this work, we study the energy transfer of excitons between their multiple components by time-resolved photoluminescence and find that charge transfer from high-energy states to low-energy state is gradually suppressed during elevating temperature owing to trap-mediated recombination. This may reveal the bottleneck of luminescence at room temperature in Q-2DPs, leading to large photovoltage loss in 2D PSC. Therefore, we develop a p-i-n bulk heterojunction (BHJ) structure to reduce the nonradiative recombination and obtain high V OC of 1.18 V for (PMA) 2 MA 4 Pb 5 I 15 Cl (33.3% PMA) BHJ device, much higher than that of the planar counterparts. The enhanced efficiency is attributed to the improved exciton dissociation via BHJ interface. Our results provide an important step toward high V OC and stable 2D PSCs, which could be used for tandem solar cell and colorful photovoltaic windows.

We demonstrate all-perovskite light-emitting diodes (PeLEDs) with white emission on the basis of simultaneously solving a couple of issues including the ion exchanges between different perovskites, solvent incompatibility in the solution process of stacking different perovskites and carrier transport layers, as well as the energy level matching between each layer in the whole device. The PeLEDs are built with a two-dimensional (CH 3 CH 2 CH 2 NH 3 ) 2 CsPb 2 I 7 perovskite that emits red light, CsPb(Br,Cl) 3 quantum dots that emit a cyan color, and an interlayer composed of bis(1-phenyl-1H-benzo[ d]imidazole)phenylphosphine oxide (BIPO) and poly(4-butylphenyl-diphenyl-amine) (Poly-TPD). The interlayer is designed to realize desirable white electroluminescence by tuning the electron and hole transportation and distribution in-between multilayers. With this PeLED configuration, we achieve the typical white light with chromaticity coordinates of (0.32, 0.32) in Commission Internationale de L'Eclairage (CIE) 1931 color space diagram and steady CIE coordinates in a wide range of driving current densities (from 2.94 to 59.29 mA/cm 2 ). Consequently, our work, as the starting point for future research of all-perovskite white PeLEDs, will contribute to the future applications of PeLEDs in lighting and display. In addition, we believe that the proposed material and all-perovskite concept will leverage the design and development of more perovskite-based devices.

In this work, we report the application of the aggregation-induced emission luminogens (AIEgens) as color converters for visible light communication (VLC). In the form of pure solid powder, the AIEgens studied herein have demonstrated blue-to-red full-color emissions, large -6 dB electrical modulation bandwidths up to 279 MHz (∼56× that of commercial phosphor), and most of them can achieve high data rates of 428-493 Mbps (up to ∼49× that of commercial phosphor) at a maximum bit error rate of 3.8 × 10 -3 using on-off keying. Their data communication performances strongly suggest that AIEgens are very promising candidates as color converters for VLC applications, together with their unique AIE properties that will benefit usage in high concentration. Based on the comprehensive experimental results, we further propose some insights into improving data rate of the color converter in VLC: the data rate limit is influenced by modulation bandwidth and signal-noise ratio (SNR). We have experimentally proved that the -6 dB electrical modulation bandwidth f c can be estimated from the effective lifetime τ of the color converter with the theoretical prediction of [Formula: see text] within experimental uncertainties, while theoretically derived that the SNR is proportional to its PL quantum efficiency. These observations and implications are very profound for exploring materials as color converters and improve the data transmission performance in VLC.

A series of pyrrolopyrrole aza boron dipyrromethene derivatives have been designed and synthesised as two-photon fluorescent probes. The bisalkynyl analogues, having a donor-π-donor quadrupolar skeleton, show a red-shifted Q band at ca. 700 nm in toluene and a two-photon absorption (TPA) cross-section up to 2349 GM at 1040 nm. To enable these dyes to be used for subcellular imaging, a branched oligoethylene glycol unit has been introduced to enhance their hydrophilicity and biocompatibility, and a potential organelle-selective group, namely triphenylphosphonium or morpholine moiety has also been added with a view to targeting the mitochondria or lysosomes respectively. The resulting conjugates are essentially non-aggregated in deionised water, exhibiting an intense Q band at 668 nm and a TPA cross-section up to 384 GM at 1040 nm. These spectral features have been analysed using density functional theory calculations, which suggest that the TPA is mainly due to the S 0 → S 2 transition. In the subcellular imaging study, it has been found that the triphenylphosphonium-containing derivative can localise in the lysosomes of HeLa human cervical carcinoma cells, which may be a result of its positive charge and the negative log P value (-2.46, P = partition coefficient), while the morpholine-substituted analogue does not exhibit preferential subcellular localisation.

Far-red and near-infrared (NIR) fluorescent materials possessing the characteristics of strong two-photon absorption and aggregation-induced emission (AIE) as well as specific targeting capability are much-sought-after for bioimaging and therapeutic applications due to their deep penetration depth and high resolution. Herein, a series of dipolar far-red and NIR AIE luminogens with a strong push-pull effect are designed and synthesized. The obtained fluorophores display bright far-red and NIR solid-state fluorescence with a high quantum yield of up to 30%, large Stokes shifts of up to 244 nm, and large two-photon absorption cross-sections of up to 887 GM. A total of three neutral AIEgens show specific lipid droplet (LD)-targeting capability, while the one with cationic and lipophilic characteristics tends to target the mitochondria specifically. All of the molecules demonstrate good biocompatibility, high brightness, and superior photostability. They also serve as efficient two-photon fluorescence-imaging agents for the clear visualization of LDs or mitochondria in living cells and tissues with deep tissue penetration (up to 150 μm) and high contrast. These AIEgens can efficiently generate singlet oxygen upon light irradiation for the photodynamic ablation of cancer cells. All of these intriguing results prove that these far-red and NIR AIEgens are excellent candidates for the two-photon fluorescence imaging of LDs or mitochondria and organelle-targeting photodynamic cancer therapy.

Two advanced boron dipyrromethene (BODIPY) based photosensitizers have been synthesized and characterized. With a glibenclamide analogous moiety, these compounds can localize in the endoplasmic reticulum (ER) of HeLa human cervical carcinoma cells and HepG2 human hepatocarcinoma cells. The BODIPY π skeleton is conjugated with two styryl or carbazolylethenyl groups, which can substantially red-shift the Q-band absorption and fluorescence emission and impart two-photon absorption (TPA) property to the chromophores. The TPA cross section of the carbazole-containing analogue reaches a value of 453 GM at 1010 nm. These compounds also behave as singlet oxygen generators with high photostability. Upon irradiation at λ > 610 nm, these photosensitizers cause photocytotoxicity to these two cell lines with IC 50 values down to 0.09 μM, for which the cell death is triggered mainly by ER stress. The two-photon photodynamic activity of the distyryl derivative upon excitation at λ = 800 nm has also been demonstrated.

π-Bonds connected with aromatic rings were generally believed as the standard structures for constructing highly efficient fluorophores. Materials without these typical structures, however, exhibited only low fluorescence quantum yields and emitted in the ultraviolet spectral region. In this work, three molecules, namely bis(2,4,5-trimethylphenyl)methane, 1,1,2,2-tetrakis(2,4,5-trimethylphenyl)ethane, and 1,1,2,2-tetraphenylethane, with nonconjugated structures and isolated phenyl rings were synthesized and their photophysical properties were systematically investigated. Interestingly, the emission spectra of these three molecules could be well extended to 600 nm with high solid-state quantum yields of up to 70%. Experimental and theoretical analyses proved that intramolecular through-space conjugation between the "isolated" phenyl rings played an important role for this abnormal phenomenon.

In this study, the concentration gradient inside evaporating binary sessile droplets of 30, 50, and 60 vol % tetrahydrofuran (THF)/water mixtures was investigated. The 5 μL THF/water droplets were evaporated on a transparent hydrophobic substrate. This is the first demonstration of local concentration mapping within an evaporating binary droplet utilizing the aggregation-induced emission material. During the first two evaporation stages of the binary droplet, the local concentration can be directly visualized by the change of fluorescence emission intensity. Time-resolved average and local concentrations can be estimated by using the pre-established function of fluorescence intensity versus water volume fraction.

Lipid droplets are dynamic organelles involved in various physiological processes and their detection is thus of high importance to biomedical research. Recent reports show that AIE probes for lipid droplet imaging have the superior advantages of high brightness, large Stokes shift and excellent photostability compared to commercial dyes but suffer from the problem of having a short excitation wavelength. In this work, an AIE probe, namely TPA-BI, was rationally designed and easily prepared from triphenylamine and imidazolone building blocks for the two-photon imaging of lipid droplets. TPA-BI exhibited TICT+AIE features with a large Stokes shift of up to 202 nm and a large two-photon absorption cross-section of up to 213 GM. TPA-BI was more suitable for two-photon imaging of the lipid droplets with the merits of a higher 3D resolution, lesser photobleaching, a reduced autofluorescence and deeper penetration in tissue slices than a commercial probe based on BODIPY 493/503, providing a promising imaging tool for lipid droplet tracking and analysis in biomedical research and clinical diagnosis.

Multiphoton microscopy is an exciting tool for biomedical research because it can be used to image single cells in vivo due to its greater penetration depth, lower phototoxicity and higher resolution when compared to confocal laser scanning microscopy. This helps researchers understand how certain cells change over time and evaluate the efficacy of different therapies. Herein, we report a new AIE luminogen (AIEgen), abbreviated as TPE-TETRAD, with a favorable absorption and efficient deep-red emission in the solid state. TPE-TETRAD possesses a high two-photon absorption cross-section (313 MG at 830 nm) and a rich array of non-linear optical properties including aggregation-induced three-photon luminescence. Biotinylated TPE-TETRAD nanoparticles are also fabricated and applied to stain mitochondria in live cancer cells with high specificity. The purpose of this study is to characterize a novel deep-red AIEgen and fabricate biotinylated nanoparticles for applications as (1) biocompatible and photostable AIE probes for specific mitochondria imaging and (2) multiphoton imaging probes suitable for two/three-photon fluorescence microscopy.

Compared to the conventional perovskite solar cells (PSCs) containing hole-transport materials (HTM), carbon materials based HTM-free PSCs (C-PSCs) have often suffered from inferior power conversion efficiencies (PCEs) arising at least partially from the inefficient hole extraction at the perovskite-carbon interface. Here, we show that boron (B) doping of multiwalled carbon nanotubes (B-MWNTs) electrodes are superior in enabling enhanced hole extraction and transport by increasing work function, carrier concentration, and conductivity of MWNTs. The C-PSCs prepared using the B-MWNTs as the counter electrodes to extract and transport hole carriers have achieved remarkably higher performances than that with the undoped MWNTs, with the resulting PCE being considerably improved from 10.70% (average of 9.58%) to 14.60% (average of 13.70%). Significantly, these cells show negligible hysteretic behavior. Moreover, by coating a thin layer of insulating aluminum oxide (Al 2 O 3 ) on the mesoporous TiO 2 film as a physical barrier to substantially reduce the charge losses, the PCE has been further pushed to 15.23% (average 14.20%). Finally, the impressive durability and stability of the prepared C-PSCs were also testified under various conditions, including long-term air exposure, heat treatment, and high humidity.

Circularly-polarized luminescence (CPL) has received new attention on the rise of applications to generate devices and biologically active probes. These applications require fluorophores that are not only chiral but also provide strong fluorescence intensity in aggregated state. Thus, a new research branch has opened up a few years ago, which allows CPL-active fluorophores to be emissive in aggregated-state. As a result, reports on the combination of the CPL property with the aggregation-induced emission (AIE) phenomenon have emerged. Herein the early design principles that have been reported until now to generate CPL-active AIE-active fluorophores (AIEgens) are summarized. In this regard the alignment of monomeric emitters in a chiral fashion, either in supramolecules, polymers or liquid crystals has been proven to be a successful approach. Additionally, first reports have appeared that demonstrate how to tackle the daunting task to furnish individual CPL-active AIEgens., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)