Search

This study aims to evaluate the incidence of low birth weight (LBW) and related maternal risk factors (during pregnancy or childbirth) and neonatal outcomes. A retrospective cross-sectional study design was used to select 7,421 pregnant women who gave birth in our hospital from January 2018 to June 2021. The data were analyzed using STATA 14.1, and the dependent variable (LBW) and risk were analyzed by the chi-square test of independence. The association between factors is used to determine the factors related to LBW through bivariate and multivariate logistic regression. The incidence of LBW in this study was 4.77%. Compared with single pregnant women, the probability of newborn LBW in married pregnant women is 40% lower (AOR = 0.60 95%CI: 0.40–0.90, p = 0.013). Compared with gestational age less than 37 weeks, the LBW probability of gestational age 37–42 and 42 weeks or older is 85 and 81% lower respectively (AOR = 0.15 95% CI: 0.10–0.24, p = 0.001; AOR = 0.19 95 %CI: 0.09–38, p = 0.001), compared with normal pregnant women, the probability of neonatal LBW among pregnant women with hypertension is 94% higher [AOR = 1.94 (95% CI: 1.39–2.74, p = 0.001). Compared with neonates with normal birth weight, neonates with LBW are at Apgar 1 min And Apgar 5 min score is lower than 7 (AOR = 0.52 95%CI: 0.37–0.73, p = 0.001, AOR = 0.54 95%CI: 0.38–0.75, p = 0.001) higher risk. In conclusion, women’s marital status (single), gestational age (

Aimed at the problems of unmanned marine exploration vessels, such as the short voyage time and the limited sensing ability caused by sensor failure under complex marine environments, a long-range unmanned ocean-air stereo exploration vessel driven by wind and solar energy is developed. An elevating ducted wind turbine is designed for high efficiency and low starting wind speed, and a deployable solar photovoltaic power generation system is developed. Therefore, wind power and solar energy can be utilized to realize a hybrid system, which overcomes the instability of single energy power supply, and effectively ensures the endurance of unmanned exploration vessel. Then, a ship-borne tethered ummanned aerial vehicle (UAV) system is developed with an autonomous takeoff and landing control section. Finally, the information fusion technology of ship borne and airborne sensors is adopted to greatly improve the perception ability of the unmanned ship to the surrounding environment and the function of three-dimension detection of sea and air. The unmanned surface vessel (USV) proposed in this paper is permitted to perform the assigned task with different types of loading equipment according to the scenarios.

To realize the practical scale application of the spar-type floating offshore wind turbine (FOWT) in the medium depth sea areas, a novel 6 MW spar-type floating offshore wind turbine is analyzed by model test and numerical simulation under extreme conditions. The response of main freedom degrees, the mooring tense and the stress at the danger point are explored by a 1∶65.3 scale model at the State Key Laboratory of Ocean Engineering in Shanghai JiaoTong University. Coupled motion response of the spar-type floating wind turbine is calculated by using numerical simulation software in time domain. The results of the numerical simulation and model test are compared and analyzed in time and frequency domain. The maximum deviation between numerical simulation and model test is less than 12%, which shows that the numerical simulation results are in good agreement with the model test results. The dynamic response energy of the FOWT is mainly concentrated at low frequency and wave frequency. Moreover, the whole FOWT system has an excellent survivability under extreme conditions. Finally, the ultimate load of the wind turbine is predicted, which provides the necessary theoretical basis and calculation parameters for the structural strength calculation.

This paper reports an efficient method of preparing porous polymeric microspheres by solvent evaporation in foam phase, in which phase separation between polymer and porogen occurs in foam phase instead of that in water phase by using the traditional solvent evaporation method. The method provides outstanding features, including being time-saving, of high-yield and able for continuous production, in which formation of porous polymeric microspheres finished within 3 min with a high production yield up to approximate 95 wt% and the process was able to be developed into a continuous process for production of porous polymeric microspheres. It was also universal to non-crosslinked polymers since the method is a development on the traditional emulsion solvent evaporation method. The new method is efficient and can be used potentially on the industrial scale for continuous production of porous polymeric microspheres.

Three-dimensional (3D) image cytometers may significantly improve the cell analysis accuracy to facilitate biological discoveries and clinical diagnosis, but their development is curbed by the low imaging throughput. Here we report SIngle-frame LAbel-free Cell Tomography (SILACT) with diffraction-limited resolution and unprecedented imaging speed of over 10,000 volumes/second. SILACT is built on a unique interferometric microscope with angle-multiplexing illumination and a pre-trained physics-incorporating Deep Neural Network for efficient 3D Refractive Index (RI) reconstruction, from which 3D morphological and biophysical parameters of cells are extracted. With microfluidics and a high-speed camera, SILACT is capable of imaging over 20,000 cells/second and distinguishing different cell species during rapid measurements of large cell quantities, as well as visualizing shear-induced 3D transient deformation of red blood cells on a sub-millisecond scale., Baoliang Ge, Yanping He, Mo Deng contributed equally to this work

Latex files and figures

A general and versatile strategy to prepare melamine-formaldehyde (MF) microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work. The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation, followed by in situ polymerization of MF precondensates as an outer shell. The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance, and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions. It was demonstrated that MF microcapsules containing clove oil were prepared successfully. The amount and the composition of the intermediate polyacrylate bridging layer were critical. Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt% and the concentration of acrylic acid (AA) increased to 10 wt% in polyacrylate. In addition, MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method. The work suggests that this new approach can be potentially used to encapsulate various core materials, tuning the shell properties of microcapsules such as thickness, mechanical strength and release properties.

The different slurry transport properties in horizontal pipeline are investigated using a steady three-dimensional hydrodynamic model based on the kinetic theory of granular flow. The flow velocity...

In this study, we carried out an amplified luminescent proximity homogeneous assay (AlphaLISA) to detect sulfonamides (SAs) antibiotic residues in plasma, milk, pork, chicken, and fish. The SAs AlphaLISA method can detect 13 SAs with half‐inhibitory concentration (IC50) 2.11–29.77 ng/ml. The detection level of those SAs was 0.3–41.12 ng/ml in matrices, which satisfied the maximum residue limit (MRL) of the European Union, United States, and China. Our recoveries are in the range of 88% to 116.8% with a coefficient of variation less than 9.3% for different spiked food samples. We observed a good correlation between the AlphaLISA and liquid chromatography–tandem mass spectrometry (LC‐MS/MS) with blood samples from injected rabbits. The established AlphaLISA method provided a no‐washing, rapid, high‐throughput screening tool for SAs in food quality control, which is suitable for small‐volume samples., An amplified luminescent proximity homogeneous assay (AlphaLISA) was carried out in the detection of 13 SAs antibiotic residues in foods with the half‐inhibitory concentration (IC50) values from 2.11 to 29.77 ng/ml. Good correlations were observed between the AlphaLISA and liquid chromatography–tandem mass spectrometry (LC‐MS/MS) results for blood samples from injected rabbits.

The aim of this work was to study an improved solvent evaporation method to prepare poly (lactic acid) (PLA) microspheres via foam-transfer. Since the foaming process and its transfer were critical to the improved method, they have been studied. Additionally, the delivery capability of foams was studied as a function of the oil/water ratio, the stirring rate, the concentration of polyvinyl alcohol (PVA) and ethanol (EtOH) in the aqueous phase (ωPVA, ωEtOH). It was found that foaming varied during the preparation process and it influenced the properties of PLA microspheres. When the oil/water ratio (w/w) ≥ 3:10, stirring rate ≥ 600 r/min, ωPVA ≥ 1 wt%, and ωEtOH = 0 wt%, solvent evaporation was able to produce enough foams for foam-transfer, which helped to deliver more than 89 wt% PLA microspheres to the receiving vessel. However, ωPVA ≤ 0.3 wt% and ωEtOH = 20 wt% were unfavorable for maintaining the spherical shape of PLA microspheres and caused the aggregation. The methodology was further used to prepare azoxystrobin-loaded PLA microspheres successfully with a high encapsulation efficiency of 86.54%. This work is meaningful since it enables an efficient and continuous route to prepare functional biodegradable polymer microspheres.

In this study, vacuum low-pressure carburizing heat treatments were carried out on 18Cr2Ni4WA case-carburized alloy steel. The evolution and phase transformation mechanism of the microstructure of the carburized layer during low-temperature tempering and its effect on the surface hardness were studied. The results showed that the carburized layer of the 18Cr2Ni4WA steel was composed of a large quantity of martensite and retained austenite. The type of martensite matrix changed from acicular martensite to lath martensite from the surface to the core. The hardness of the carburized layer gradually decreased as the carbon content decreased. A thermodynamic model was used to show that the low-carbon retained austenite was easier to transform into martensite at lower temperatures, since the high-carbon retained austenite was more thermally stable than the low-carbon retained austenite. The mechanical stability&mdash, not the thermal stability&mdash, of the retained austenite in the carburized layer dominated after carburizing and quenching, and cryogenic treatment had a limited effect on promoting the martensite formation. During low-temperature tempering, the solid-solution carbon content of the martensite decreased, the compressive stress on the retained austenite was reduced and the mechanical stability of the retained austenite decreased. Therefore, during cooling after low-temperature tempering, the low-carbon retained austenite transformed into martensite, whereas the high-carbon retained austenite still remained in the microstructure. The changes in the martensite matrix hardness had a far greater effect than the transformation of the retained austenite to martensite on the case hardness of the carburized layer.

A solvent evaporation self-motivated synthetic methodology based on foaming-transfer has been developed to fabricate porous polymer microspheres. The novel method is a technical improvement for the traditional solvent evaporation method, in which solvent evaporation enables foam formation and foaming-transfer. Foaming-transfer helps deliver oil droplets from the aqueous phase to the receiving vessel, while phase separation takes place in oil droplets between polymer and porogen to produce porous polymer microspheres. Because of foaming-transfer, the novel method enables a continuous production of polymer microspheres via continuous feeding. Additionally, high efficiency has been observed since solvent evaporation in foams is much quicker than that in the aqueous phase. The methodology was further developed to prepare versatile porous polymer microspheres by introducing extra organic solvents, including ethanol (EtOH), acetone and ethyl acetate. Solvents like EtOH and acetone that have relatively poor compatibilities with oil phase were able to control structure, surface morphology and particle size of polymer microspheres when varying the concentration of solvents; while introducing solvents like ethyl acetate having good miscibility with oil phase hardly changed these properties. It was mainly because the difference on the compatibilities led to different distributions of solvent molecules in the system, which altered the evaporation process of solvent and the surface tension of the system, leading to the variation on structure, particle size and surface roughness. This work is meaningful since it developed an efficient, continuous and versatile method for the production of porous polymer microspheres.

This study has developed a method to produce porous polymeric microspheres in a foam phase. And, the foam phase was a mixture of polymer, organic solvent, porogen and emulsion stabilizer. The process was comprised of a series of constant steps homogenization of the materials, growth of the foam phase and collection of the products. The growth of the foam phase was the key which combined mechanical agitation, solvent evaporation and oil droplets development under increasing temperature. The method has been seen time-saving, high yield and continuous process and it could be useful for industrial production of porous polymer microspheres in a continuous process.

Polymeric microspheres with different internal structures have been widely used because of their characteristics in the structures. This paper reports a method of controlling the internal structures of polymeric microspheres via the introduction of a water-soluble organic solvent to the continuous phase in the foam phase preparation of porous polymeric microspheres. The introduction of a water-soluble organic solvent enables the control of polymeric microspheres’ internal structures, from porous to hollow. Because a water-soluble organic solvent is introduced, the organic solvent may be diffused toward the interface because of the affinity between the organic solvent and the oil droplets, resulting an accumulation of organic solvent molecules at the interface to form an organic solvent layer. The presence of this layer may decrease the evaporation rate of the internal organic solvent in an oil droplet, which extends the time for the mingling of porogen droplets to form a few large pores or even an extremely large single pore inside. This method is also capable of altering the thickness of hollow microspheres’ shells in a desired way, with improved efficiency, yield and the capacity for continuous use on an industrial scale.

In this study, formulation of latex with methyl methacrylate (MMA) as a function of surfactant concentration ([S]) under critical micelle concentration (CMC) was investigated to explore the nucleation mechanism and the key to control the particle number (N p) of latex in emulsion polymerization. Influences of surfactant concentration [S] on the conversion of monomer, particle size (PS), N p, and surfactant surface coverage (θ) were studied, as well. Flocculation nucleation was considered as the main mechanism to generate particle nuclei when [S] was much less than CMC. The nucleation mechanism experienced an evolution of a flocculation nucleation-dominated region ([S] 3.3 mmol L−1). The contribution ratio of the flocculation nucleation was 86 % compared with the micellar nucleation. The particle number (N p) was found to be controlled by the combination of micellar and flocculation nucleation-dominated regions under CMC, and the regulation range was about 1–6. The results can be used to guide the preparation of a bimodal high solid content (HSC) latex by creating a population of small particles in the presence of an initial population of larger ones in a controllable way. In this way, a controllable amount of large latex particles were prepared using a high emulsifier concentration, at first, and then the second population of small particles was formulated by secondary nucleation at a proper time through controlling surfactant concentration at a low level, followed by the growth of the two groups of the particles, and then the bimodal HSC latex can be prepared at low viscosity.

In this paper, the photophysical and photosensitive properties of Elsinochrome A (EA), another member of perylenequinone photosensitizers derived via artificially biological synthesis, were studied by taking hypocrellin A (HA) and hypocrellin B (HB) as the references. It was found that the quantum yield of singlet oxygen produced via the photosensitization of EA was 0.98 with HB (0.84) as a reference. Furthermore, the semiquinone anion could be produced via photosensitization of EA in oxygen-free solution. Besides, taking advantage of nanosecond time-resolved spectral technique, the transient triplet absorption spectra and the lifetime of EA in cyclohexane were determined by the use of the ground-state depletion method.

Productivity of a country especially developing nations largely depends on foreign endeavors through technological spillovers as a crucial engine for growth. Using a constructed panel of 47 countries from 1990 to 2006, this paper theoretically and empirically investigates two of the most important channels for technology spillovers (trade and FDI). The results confirm the fact that trade remains an important source for productivity increases via technological spillovers for both developed and developing countries, surpassing their domestic R&D efforts. Foreign direct investment seems to have a significant but much smaller impact, predominantly in developing countries. Openness to both trade and FDI from developed nations is beneficial for all countries but mostly to developing economies.

To improve dredging efficiency and expand transportation, trailing suction dredger with shuttle barge moored at one side is applied in long distance reclamation projects. Line arrangement and line tension estimation method is established for prototype testing of this new technique. The variation rule of line tension in different operation stage is studied and a program working on optimal relative position of two vessels with minimum deformation energy is put forward. The computational results are evaluated by comparing with experiment data.

Dental caries is a common and costly multifactorial biofilm disease caused by cariogenic bacteria that ferment carbohydrates to lactic acid, demineralizing the inorganic component of teeth. Therefore, low pH (pH 4.5) is a characteristic signal of the localised carious environment, compared to a healthy oral pH range (6.8 to 7.4). The development of pH-responsive delivery systems that release antibacterial agents in response to low pH has gained attention as a targeted therapy for dental caries. Release is triggered by high levels of acidogenic species and their reduction may select for the establishment of health-associated biofilm communities. Moreover, drug efficacy can be amplified by the modification of the delivery system to target adhesion to the plaque biofilm to extend the retention time of antimicrobial agents in the oral cavity. In this review, recent developments of different pH-responsive nanocarriers and their biofilm targeting mechanisms are discussed. This review critically discusses the current state of the art and innovations in the development and use of smart delivery materials for dental caries treatment. The authors’ views for the future of the field are also presented. Refereed/Peer-reviewed

Refereed/Peer-reviewed Dental caries is a major disease associated with the proliferation of acidogenic bacterial species such as Streptococcus mutans that are part of the commensal microbiota of the mouth. Silver nanoparticles (AgNPs) are attractive antibacterial agents as they target multiple sites in bacteria which reduces antimicrobial resistance. In this study, we synthesised stable, highly positively charged AgNPs capped with branched PEI (BPEI-AgNPs) and characterized them using UV–vis absorption, transmission electron microscopy (TEM), the size of which were approximately 7.5 nm. The antibacterial activity and anti-biofilm capacity of BPEI-AgNPs was investigated against cariogenic bacteria. Our results demonstrated that BPEI-AgNPs are potent clinical oral antiseptics. The cytotoxicity of the BPEI-AgNPs was also studied against two mammalian cell lines. The results indicated that BPEI-AgNPs were non-cytotoxic and were safer than commercially used dental antiseptics. We conclude that the BPEI-AgNPs are safe for oral clinical application and are an effective oral antimicrobial agent.