Search

The hybrid rocket motor (HRM) emerges as a promising propulsion system offering thrust adjustment at a low cost. Prior research has indicated that the inclusion of micro Al additives enhances HRM performance, yet a comprehensive investigation remains absent. Thus, this study aims to explore the impact of Al particle additive content and size variation on the characteristics of hybrid rocket motors (HRMs) through experiments and simulations. Firing tests are conducted on HRMs employing unadulterated HTPB, 38 % additive Al (2 μm), and 58 % Al (2 μm). Experimental findings reveal enhancements of 12.6 % and 33.9 % in regression rate, and 2.5 % and 8.0 % in specific impulse for the 38 % Al and 58 % Al fuel configurations, respectively, compared to the base case. Subsequently, a numerical two-phase combustion model is built to analyze the inner flow field characteristics. The high consistency between experimental and simulation results validates the efficacy of the numerical approach employed. Following this, a series of simulations covering Al content ranging from 0 % to 58 % and Al particle sizes from 0.4 μm to 75 μm is conducted. Simulation outcomes indicate that specific impulse and combustion efficiency enhancements correlate with the increase in Al mass fraction for particles with diameters under 35 μm. However, high Al content proves detrimental to specific impulse and combustion efficiency when particle diameter exceeds 35 μm. Additionally, regression rate and thrust demonstrate an increase with Al content, albeit the rate of increment diminishes with larger Al particles. This study comprehensively examines the influence of Al particle addition on HRM performance and elucidates the underlying mechanisms, thereby offering insights into HRM design and manufacture. • Hybrid rocket firing tests are performed on HTPB, 38 %, and 58 % Al particle fuel. • Simulations with various Al particle contents and diameters are performed. • High Al content with diameter under 35 μm is beneficial for combustion efficiency. • High Al content with diameter over 35 μm is detrimental for combustion efficiency. • Large particle reduces the thrust enhancement brought by Al content rise. [ABSTRACT FROM AUTHOR]

This paper studies the effects of liquid oxidizer flow distribution on combustion characteristics and performance of hybrid rocket motor with axial injection through numerical simulations of two-phase flow. Axial injection is widely used in hybrid rocket motor, however, the regression of burning surface may change combustion efficiency of the motor at different moments. Consequently, it is necessary for hybrid rocket motor to design injector patterns that could increase the average combustion efficiency in the whole operating process. The orifice injector plate is divided into three areas, which are recorded as zone I, zone II and zone III, respectively. Oxidizer flow distribution is achieved through changing the diameter of injector holes in various zones, and three-dimensional steady numerical simulations of two-phase flow of hybrid rocket motor with axial injector patterns at different moments are conducted. The motor adopts 98% hydrogen peroxide and hydroxyl-terminated polybutadiene as the propellants. Numerical analysis reveals that oxidizer flow distribution mainly influences the flow field structure in the pre-combustion chamber and front part of fuel grain port. Increasing oxidizer mass flow rate in zone III is beneficial for the chamber head thermal environment. Relative position in the radial direction of fuel grain inner surface and oxidizer distributed in the injector plate affects fuel regression rates, and the influence mainly exists in the front part of solid fuel grain. When the oxidizer mass flow rate in zone I is equal, the average fuel regression rate rises with the increase of oxidizer flow rate in zone II at initial moment, and decreases as the oxidizer in zone II increases at middle moment. The average combustion efficiency increases with the increase of oxidizer mass flow rate in zone II when the oxidizer in zone I remains unchanged. Both the average combustion efficiency and the chamber head thermal protection need to be considered in the design of axial injector patterns. Research results of this paper provide an important reference for the design of high performance injector patterns of hybrid rocket motor. • Effects of oxidizer flow distribution on hybrid rocket motor performance are studied. • Steady two-phase flow simulations for various injector patterns are conducted. • Adding oxidizer in zone III is good for thermal environment of the chamber head. • Relative position of fuel inner surface and oxidizer affects fuel regression rates. • When zone I is fixed, combustion efficiency raises with oxidizer in zone II adding. [ABSTRACT FROM AUTHOR]

This study is aimed to determine and better reveal the mixture enhancement and regression rate distribution of hybrid rocket motor with diaphragm by numerical approach. A numerical model based on the computational fluid dynamics software is built to simulate the flow and combustion inside the motor. Four firing tests of the motor, including one without diaphragm and three with diaphragm, are conducted on a standard experimental system and also used as a reference for numerical simulation, the consistency between the simulation and experiment demonstrates that the numerical approach is an effective method to study the diaphragm effect on the motor performance. The flow field characteristic and regression rate distribution inside the hybrid rocket motor are then calculated to analyze the effect of position and diameter of the diaphragm. The results indicate that the diaphragm almost have no effect on the regression rate before it. However, the regression rate after the diaphragm has a strong dependence on the position and diameter of the diaphragm. As the diameter decreases and the position moves backward, the regression rate increases larger and larger, this is mainly due to the augmentation of the eddy generated by the diaphragm, which enhances the heat feedback transferred to the grain surface. When the diameter of diaphragm located at middle of grain decreases from 50 mm to 20 mm, regression rate is increased from 0.30 mm/s to 0.57 mm/s. The use of the diaphragm does cause a combustion efficiency improvement; the maximum combustion efficiency is enhanced to 98.9% from lower than 90% of the motor with no diaphragm. The increasing amplitude displays a square relation with the diameter decrease, since the entrainment of the eddy make the reactants mix sufficiently to release more energy inside the motor. [ABSTRACT FROM AUTHOR]

Orifice injector plates are widely used in hybrid rocket motors (HRM), but little work has been done on the influences of their design parameters on combustion performances of HRM. The effects of orifice diameter, injection pressure drop and orifices distribution of the orifice injector plate on combustion efficiency of HRM are investigated by experimental and numerical methods in this paper. The hydrogen peroxide (H 2 O 2) and hydroxyl terminated polybutadiene (HTPB) with tube grain are selected as propellant. Firstly, 5 kinds of orifice injector plates with different orifice diameter and orifices distribution are designed, and 7 fire experiments are carried out. The experimental results show that the combustion efficiency of HRM increases with the decrease of orifice diameter and injection pressure drop. Moreover, the combustion efficiency of motor with plat using single-ring distribution is the highest, while the one using three-ring distribution is the lowest. Secondly, 36 orifice injector plates with different design parameters are calculated by three-dimensional numerical simulation of two-phase flow. The liquid oxidizer evaporation, solid-gas interaction, gaseous phase combustion, and turbulence are considered in the simulation model. The conclusions draw from simulation results agree with the experimental data, which illustrates the validity of numerical simulation model. The conclusions based on experimental and numerical results can provide guidance for designing high-performance orifice injector plate in HRMs. • Numerical and experimental studies on orifice injector plates are conducted. • The effects of design parameters of orifice injector plate on combustion efficiency are investigated. • The combustion efficiency increases with the decrease of orifice diameter. • The combustion efficiency rises with the decrease of injection pressure drop. • The orifices distribution should be choose based on mission requirements of HRMs. [ABSTRACT FROM AUTHOR]

This paper is aimed to analyse the combustion characteristics of hybrid rocket motor with multi-section swirl injection by simulating the combustion flow field. Numerical combustion flow field and combustion performance parameters are obtained through three-dimensional numerical simulations based on a steady numerical model proposed in this paper. The hybrid rocket motor adopts 98% hydrogen peroxide and polyethylene as the propellants. Multiple injection sections are set along the axis of the solid fuel grain, and the oxidizer enters the combustion chamber by means of tangential injection via the injector ports in the injection sections. Simulation results indicate that the combustion flow field structure of the hybrid rocket motor could be improved by multi-section swirl injection method. The transformation of the combustion flow field can greatly increase the fuel regression rate and the combustion efficiency. The average fuel regression rate of the motor with multi-section swirl injection is improved by 8.37 times compared with that of the motor with conventional head-end irrotational injection. The combustion efficiency is increased to 95.73%. Besides, the simulation results also indicate that (1) the additional injection sections can increase the fuel regression rate and the combustion efficiency; (2) the upstream offset of the injection sections reduces the combustion efficiency; and (3) the fuel regression rate and the combustion efficiency decrease with the reduction of the number of injector ports in each injection section. [ABSTRACT FROM AUTHOR]

The objective of this effort is to study the combustion performance of a hybrid rocket motor with the help of 3D steady-state numerical simulation, which applies 90% hydrogen peroxide as the oxidizer and hydroxyl-terminated polybutadiene as the fuel. A method of secondary oxidizer injection in post-chamber is introduced to investigate the flow field characteristics and combustion efficiency. The secondary injection medium is the mixed gas coming from liquid hydrogen peroxide catalytic decomposition. The secondary injectors are uniformly set along the circumferential direction of the post-chamber. The simulation results obtained by above model are verified by experimental data. Three influencing parameters are considered: secondary injection diameter, secondary injection angle and secondary injection numbers. Simulation results reveals that this design could improve the combustion efficiency with respect to the same motor without secondary injection. Besides, the secondary injection almost has no effect on the regression rate and fuel sueface temperature distribution. It is also presented that the oxidizer is injected by 8 secondary injectors with a diameter of 7–8 mm in the direction of 120°in post-chamber is identified as the optimized secondary injection pattern, through which combustion efficiency, specific impulse efficiency as well as utilization of propellants are all improved obviously. [ABSTRACT FROM AUTHOR]