Search

In this paper, Kevlar or Polysulfonamide (PSA) pulp were used to replace plant fiber pulp partially or completely and by adjusting their ratios and a variety of Kevlar or PSA pulp reinforced activated carbon fiber paper (ACFP) were prepared via wet-laid paper making technology. The influences of addition of Kevlar or PSA pulp on the permeability, mechanical property, filtration performance, adsorption property of ACFP were discussed by maintaining the addition content of activated carbon fiber unchanged. Results showed that with the addition content of Kevlar or PSA pulp increased, the permeability and filtration performance of ACFP decreased obviously, while the bursting strength and the static CCl4 adsorption performances were firstly increased and then decreased. Generally, the permeability and filtration performance of Kevlar pulp reinforced ACFP were slightly worse than that of PSA pulp reinforced ACFP, while the bursting strength as well as the static CCl4 adsorption properties of Kevlar pulp reinforced ACFP were better than that of PSA pulp reinforced ACFP.

Super absorbent polymer (SAP) and fluff pulp were used as absorbing materials, and the different SAP mass ratio and fluff pulp were applied to paper diaper absorption core layer. Then, the influence of different SAP/fluff pulp in composite core layer on the paper diapers normal saline absorption rate and topsheet run-off were studied. Results showed that SAP has a significant effect on normal saline absorbency respect to fluff pulp. When the normal saline volume increased, the paper diapers absorption rate about normal saline decreased, while the topsheet run-off increased. When the SAP mass ratio to fluff pulp was 0.5:0.5, the liquid absorbency rate was 35.23 g/g, the paper diaper average absorption rate was 3.96 mL/s, and the biggest topsheet run-off was 13.25 g.

Fe-pillared bentonite was made into a paper-like composite by a papermaking technique using pulp fiber and activated carbon fiber. Orange II was used as a model compound to investigate the photocatalytic performance of the paper. SEM analysis showed that the catalytic paper had a porous structure originating from the layered fiber network, with Fe-pillared bentonite mostly embedded in the grooves along the axial direction of the carbon fibers. The optimum preparation conditions were: activated carbon fiber:Fe-pillared bentonite=1:2, activated carbon fiber:pulp fiber=5:3, the charges of Na2SiO3 and PAE were 2.5% based on the Fe-pillared bentonite and 0.4% based on the oven-dry fibers, respectively. The degradation ratio reached 85.2% at 180 min and after that little increase was observed. The catalyst could be repeatedly use and keep a high stability during the first 4 cycling use.

The aim of this research was to produce three-layer Medium Density Particleboard (MDP), with the addition of impregnated paper, in the inner layer, in proportions of 1; 5 and 20%. In this study, MDP was composed with particles of small size in outer layers, and larger particles in internal layer. After panel manufacturing, physical and mechanical tests based on Brazilian Code ABNT NBR 14.810 were carried out to determine moisture content; density; thickness swelling; water absorption; modulus of rupture (MOR) and modulus of elasticity (MOE) in static bending and internal adhesion. Test results were compared to commercial panels, produced with 100% Eucalyptus, considering the requirements specified by Brazilian Code. Properties presented values close to normative specifications, indicating positively the possibility of production of MDP using addition of waste paper impregnated.

Rabbit is a traditional textile material and has protein content about 93%. Rabbit hair wastes are abundantly present in textile processing due to its poor spinnability. In order to recycle the waste rabbit fiber effectively, the rabbit protein was researched. The papermaking method was performed for the first time and their properties of the hybrid paper were discussed in this study. Different contents of rabbit protein were successfully prepared and mixed with pulp fibers to remade papers. Finally, performances of these papers were characterized. The results showed that the surface of the rabbit protein paper was flat, white and writing fluently. The ink absorbance of novel paper increased. Moreover mechanical properties of the rabbit protein paper were stronger than the untreated paper. The folding endurance decreased firstly and then increased.

Both water repellency and water vapour barrier properties were endowed at paper surface by coating with beeswax-chitosan latex. It was found that the water vapour transmission rate of coated paper decreased as the drying temperature increased. However, water contact angle was not affected with it. Although the surface morphology deformed at high drying temperature, the roughness values maintained at micro-scale. Further analysis indicated that the water vapour barrier property of coated paper was influenced by the density of the coating layer.

Ink penetration and distribution affect the final appearance of printing and usage of ink, which are closely concerned by printer and paper maker. The objective of this experiment was to investigate the relationship between drying and back trap mottle. The different drying temperature was carried out to change the coating structure and properties. Fluorescent ink was used to observe and characterize ink distribution by LSCM. The results indicated that drying temperature affected ink distribution evenness. Higher and lower drying temperature could not contribute to ink absorption uniformity. Appropriate drying temperature could contribute to form the best printability of coated paper. Backtrap mottle was tightly linked with ink penetration evenness and uniform ink absorption leaded to little back trap mottle.

The structure of the coating layer has a strong influence on the optical and physical properties of paper as well as on the print quality. Ink is transferred and sets onto the paper surface in the printing process, which affect printing quality and usage of ink. The objective of this experiment was to investigate the influence of calender on coating surface structure and Printability. The surface structure was explored in the method of numerical and visual analysis using mercury porosimetry measurement and scanning electron microscopy (SEM). The findings indicated that the calender treatment affected the pore size, depth and distribution of the coated paper surface. It could be concluded that Calender could increase the smoothness, gloss and paper surface efficiency of coated paper, which resulted in lower amount of ink usage, lower amount of ink absorption and higher print density.

The electric papers have a wide variety of uses like in transformers, cables and power capacitors. Each application involves different requirements related to its mechanical and electric properties. The kraft is the dielectric paper most used due its high mechanical resistance and a dielectric strength of around 5 kV/mm that is increased up to 30 kV/mm when is impregnated with mineral oil and typically has a density of 0.7, nevertheless continuous improvements in the design, for example, of power transformers raise the need to improve its electrical properties particularly those related to its relative permittivity. In this article, structural parameters such as distribution and pore size of kraft paper and theoretical analysis for possible addition of nanofillers to improve their dielectric behavior are reported. A possible and better criterion for designing transformers can be the employment of kraft paper nano-inserted with 5 % of TiO2 or BaTiO3 stew in mineral oil and immersed in natural ester liquid.

The aim of this study was to obtain the effect of drying methods on surface properties and ink penetration. Laser scanning confocal microscope (LSCM) was used in order to characterize the penetration depth through quantitative analysis. Fluorescent ink was used to observe and characterize ink penetration and distribution by LSCM. The results showed that the drying methods had an important role on the surface properties and ink penetration of coated paper. Infrared drying compared with vacuum drying and hot air drying was good to improve the paper properties, which resulted in low roughness, high gloss, low ink absorption and high paper surface efficiency. It could be concluded that infrared drying compared with vacuum drying and hot air drying resulted in the highest print density and better printability.

Polyimide fibers and polyamide acid fibers was used as main materials to produce Polyimide fiber paper. A certain amount of PEO and aramid pulp was added and the sheet was treated by immersion and hot pressing in specified process. The experimental results showed that when the dosage of PEO and aramid pulp were 0.06% and 6% respectively, the sheet tended to present more excellent strength properties and electrical performance compared with sheet using single polyimide fibers as the main fiber materials.

In this study, paper sludge ash, a waste from pulp and paper industry was used as a filler in fabricating Plaster of Paris/paper sludge ash composites. Various percentage of paper sludge ash was used, namely 1wt.%, 3wt.%, 5wt.% and 7wt.%. The effect of paper sludge ash on the compressive strength of the Plaster of Paris was studied. The mixed powder of paper sludge ash and Plaster of Paris were form into a 6 mm diameter and 12 mm height cylindrical samples. The composites were characterized theirs density where it shows that the density decreased as the amount of paper sludge ash increased. The compressive strength of the composites also decreased from 11.67 MPa without paper sludge ash addition to 0.50 MPa at 7wt.% paper sludge ash. However, the requirement of strength for Plaster of Paris in industry is between 8.96 MPa to 20.68 MPa. From the SEM observation, sample contain higher percentage of paper sludge ash exhibited more porosity. Therefore with the addition of 1wt.% of paper sludge ash into Plaster of Paris can be a promising construction material.

The surface topography and properties of coating layer have an important influence on penetration and distribution of the print ink. In this research, the main objective was to investigate the effect of binder migration on the coating surface microstructure. The surface microstructure was explored in the method of numerical and visual analysis using mercury porosimetry measurement, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The findings indicated that the binder migration on the coating surface affected the pore size, depth and distribution of the coated paper surface. The little binder migration in the consolidation phase of coating color made a contribution to the forming of the coating layer, which made the coating surface more smother to printing performance.

Pulp from the oil palm empty fruit bunches (EFB) was extracted via Alkaline Peroxide Pulping (APP). The pulping process was conducted through three main steps; dewaxing of EFB, impregnation of alkaline peroxide (AP) into EFB and refining of biomass to finally produce the pulp. The varying peroxide levels and number of impregnation stages were found to affect the refining energy consumption and the properties of the resultant pulp and paper. Diagnosis by electron microscopic imaging revealed a strong correlation between paper properties development and paper surface morphologies. By multiplying the stages of the low alkaline peroxide level (2:2.5% AP) impregnation, refining energy could be reduced by 30% while improving brightness and paper mechanical properties. Higher alkaline peroxide level (4:5% AP) could reduce the refining energy by 50% while still improving brightness. Beyond these AP levels (8:10% AP), refining energy could be reduced by 67% by increasing the number of impregnation stages, with positive effects on brightness and paper mechanical properties. The findings suggest that increasing the AP impregnation stages had exposed more active sites to react with AP. The enhanced AP accessibility to EFB structures facilitated mechanical fibrillation of EFB vascular bundles through the refining process. The proper synergy between AP and the adopted mechanical refining was the factor that triggered the liberation of nanocells from EFB biomass and this had ultimately improved paper properties.

Two silane-based hybrid coatings were developed to modify the surface energy of phenolic resin impregnated paper. The coated paper samples were further pressed onto surfaces of plywood. The surface properties and water repellence of coated paper were investigated by AFM, XPS and water contact angle measurements. The water absorption of plywood with pressed paper was studied by water uptake tests. It was found that the sol-gel coatings had slightly improved the water repellence of the impregnated paper. The water absorption of plywood was also slightly decreased.

Application in paper pulp as dry strengthening agent of homemade water in water cationic polyacrylamide (CPAM) emulsion was studied. Good collaborative effect was achieved when Homemade CPAM was used in bleached wheat straw pulp with strengthening agent E and with cationic additives L as paper pulp strengthening agent. It was also showed that distinct strengthening effect was obtained when homemade CPAM emulsion was applied in mixture of wood pulp which was needle bleached kraft pulp (NBKP) and straw pulp, breaking length and tearing index of hand sheet made of mix pulp was respectively increased by 22.2% and17.0% when the dosage of CPAM was 0.8% of dry fiber. Through analysis of handsheet section scanning electron microscopy (SEM) photos, strengthening mechanism of CPAM emulsion to paper pulp was preliminary studied.

This research were examined the spinning processes of paper mulberry yarn and also investigated the physical properties of paper mulberry yarn. The results show that a possibilities of spinning of paper mulberry fiber into yarn which is a longitudinal view similar to that of cotton. An average yarn count, tenacity and elongation are 1,022 tex, 66.39 cN/tex, and 17.80%, respectively. These results represent the beginning of the research to rescue traditional knowledge, combined with the possibility of the introduction of a new textile fiber on the market.

This research were examined the characteristics chemical and physicalof paper mulberry fiber and also developed the spinning processes of paper mulberry yarn to make the fabric by weaving and knitting. The chemical composition of paper mulberry fiber was approximately 72.5% cellulose, while hemi-cellulose, lignin, pectin, and water-soluble were 17, 2.6, 2.3, and 5.6%, respectively. The characteristics and physical properties of paper mulberry fabric were also investigated.

The application of hydrated calcium silicate as filler in paper from wheat straw pulp is studied in this paper. It shows that that with the increase of dosage of hydrated calcium silicate, the stiffness of paper improves, and the whiteness and the printing color density of paper improve, but the tightness and tensile strength of paper decrease. When the dosage of CPAM is 0.45 g/kg, the tightness, tensile strength, tearing index, whiteness and printing color density reach the large value. Paper ash content increased with the increase of amount of hydrated calcium silicate, but paper ash gains is not big after the dosage of hydrated calcium silicate reaches 20%.

The Paper studied the effects of pigments and base paper on binder migration and affected factors. The z-direction distribution of the coating binder which was tagged with Br in coating layer and its concentration in coating surface were examined quantitatively by using SEM-EDXA and ESCA analysis. The results showed that the increase of the ratio of calcium carbonate in the pigment content, coating surface binder concentration increased, and coating surface binder concentration increased with the increase of particle size of pigments. The result also indicated to small base paper absorbency, coating surface has high binder migration level, the coating layer bottom (base paper direction) has low binder concentration. To high absorbency base paper, the opposite is true.

The coating binder migration and concentration in z-direction of coating layer especially in coating surface influence the coated paper printing properties. The results indicated that with the increase of coating surface binder migration, the coated paper opacity decreases, and the K&N value decreases. The relationship of K&N value and binder concentration in surface of coating layer was linear, which indicated that compared to binder dosage concentration in coating color, the K&N value and coating surface binder concentration has higher correlation. The more uniform the binder distribution in cross section of coating layer, the greater the IGT.

The paper wooden compound pallets are produced through the processing and assembly by using particle board, paper tubes and PE coated paper board as raw materials. Comparing with traditional wooden flat plate, the new type of green environmental protection pallets has many advantages such as high strength, light weight, low cost, waterproof, anti-moth-eaten, no need fumigation, etc. is an ideal green transport packaging materials for export commodities. The paper discusses and probes into the process and technology of paper wooden compound pallets.

Waste paper sludge ash (WPSA) is a byproduct and problematic waste of paper industries. The investigation was driven by the increasing demand for reuse options in paper-recycling industry. This paper present on the morphology and physical analysis studies on polymerization of WPSA mortar. Two (2) types of polymeric mortar mixes containing WPSA with alkaline activators and without alkaline activators were prepared. The morphology of each mixes was determined using Spectra Electron Microscope (SEM) and the physical test is focus on compressive strength. However, the element diffraction of each mixes using Energy Dispersive X-Ray Spectroscopy (EDX) was also carried out as a method to identify the polymerization of polymeric mortar. From the result obtained it is found that the utilization of WPSA reduced the polymerization of polymeric mortar due to more pores. From the EDX analysis it is also revealed that the WPSA polymeric mortar also contained less synthetic aluminous silicate compound. However, the strength gain up to 6MPa and it is comparable with other high calcium material mortar.

What happens in the paper surface about ink absorption is of great important for appearance of final printing. The aim of this experiment was to investigate the influence of printing pressure and printing speed on ink layer thickness transferred onto coated paper through quantitative analysis by laser scanning confocal microscope (LSCM). Meanwhile, the influence of printing pressure and printing speed on print density and print gloss were obtained. The results implied that higher printing pressure resulted in higher ink layer thickness, print density and print gloss when printing pressure is less than 700N, but higher printing speed resulted in lower ink layer thickness, print density and print gloss when printing pressure is constant. It could be concluded that the coated paper with high printing speed compared with low printing speed resulted in lower ink absorption, lower print density, lower print gloss and worse printability on the condition of same printing pressure.

The objective of this experiment was to investigate the influence of coating solid on surface properties and ink penetration and to characterize the penetration depth through quantitative analysis by laser scanning confocal microscope (LSCM). Fluorescent ink was used to observe and characterize ink penetration and distribution by LSCM. The results implied that the surface properties of coated paper could be adjusted and improved by increasing the coating solid. With the increasing of coating solid, ink penetration depth declined and ink penetration uniformity increased. It could be concluded that the coated paper with high coating solid compared with low coating solid resulted in lower ink usage and better printability on the condition of same print density.

A novel hollow microsphere plastic pigment was prepared by the soap-free seeded emulsion polymerization. This pigment, with polyacrylate as core and with polystyrene as shell (PA/PSt) had hollow structure after dryness. The latex was characterized by transmission electron microscopy (TEM), Fourier transform infrared spectra (FTIR), and particle size analysis. The synthetic pigment was applied in the paper coating, and its influence on the printablility of the coated paper was investigated. The results show that the overall properties of the coated paper can be effectively improved when the clay in the base formulation is replaced by a small amount of hollow microsphere plastic pigment.

Fibers of dissolved air flotation rejects were been carboxymethylated to make dry strengthening agent. The effects of carboxymethylated time on carboxyl content, water retention value and physical properties of paper sheets were discussed. The effects of pH, dose of additive agent and additive aluminum sulfate on paper properties were discussed. The result show that carboxyl content and water retention values increased with the increasing of carboxymethylated time according to the research. IR analysis indicates that carboxymethyl has been connected to the surface of fibers. SEM micrographs shown that fibers were intergraded more closely benefit from the addition of dry strengthening agent. Tensile index, burst index and folding endurance respectively increased by 90.1% 101.8% and 833.3% on the condition: the additive agent amount 3%, pH 5, additive aluminum sulfate 0.5% of original pulp. Tensile index, burst index and folding endurance respectively increased by 74.0%, 87.8% and 877.8% when the carboxymethylated time was 110min for recycled pulp. This paper can be used as the theoretical basis for reusing of fiber of dissolved air flotation rejects.

The ink penetration behavior depends on the coating surface structure and surface properties of the coating layer in the papermaking process, which include coating recipes and coating conditions, etc. The objective of this experiment was to investigate the relationship between binder content and ink absorption using laser scanning confocal microscope (LSCM). Fluorescent ink was used to observe and characterize ink penetration and distribution in coated paper by LSCM. The results indicated that higher binder content could result in higher amount ink absorption. With the increasing of binder content, ink penetration depth in coated paper increased. Sample G2 with 20 parts binder produced the most unevenness ink distribution. It could be concluded that the coated paper with 25 parts binder compared with the other samples resulted in higher ink usage and better printing quality.

The surface topography and properties of coating layer have an important influence on penetration and distribution of the print ink. In this research, the main objective was to investigate the effect of binder on the coating surface topography and characteristics. The surface microstructure was explored in the method of numerical and visual analysis using mercury porosimetry measurment and atomic force microscopy (AFM). The findings indicated that the binder content on the coating surface affected the pore size, depth and distribution of the coated paper surface. The conclusions were drawn that more amount of binder on the coating surface could contribute to improve the coating surface topography and the formation of even pore size and distribution, which was good to the paper surface characteristics and resulted in low roughness, high paper gloss, low ink absorption and high paper surface efficiency.

Polyimide fibers and polyamide acid fibers was used as main materials to make polyimide fiber paper. The effect of the properties of polyimide fiber paper by hot pressing temperature and hot pressing pressure was discussed. The experimental results showed that when the pressure of hot pressing was 12Mpa and the hot temperature of hot pressing was 220°C, the sheet had excellent strength properties and electrical performance.

In present time, recycled paper from xerographic and laser-printed wastepaper plays an important role as alternatives to paper from virgin pulp because of their good pulp quality and high amount of wastepaper each year. This type of paper is classified as Mixed Office Wastepaper (MOW). The xerographic and laser-printed inks are usually called “toner” which its formulation is different from conventional ink. This work aimed to investigate paper recycling by flotation deinking process. The flotation experiments were conducted using SDS (sodium dodecyl sulfate) and Triton X-100 (C14H22O(C2H4O)n). The experimental results demonstrated that ink removal was more efficient with the use of non-ionic surfactant (Triton X-100) than anionic surfactant (SDS). The efficiency of ink removal was determined by ERIC and the pulp’s brightness. In addition, the quality of de-inked pulps was evaluated by pulp physical properties such as burst strength, tear strength and tensile strength.

In this paper, a kind of sizing synergist,AKD,cationic rosin(CRS) and oil resistance agent were mixed in different proportions, we make it as a kind of new water repellent agent ,and for internal sizing. The best dosage and the composite ratio of the synergist, AKD, cationic rosin and oil resistance agent was discussed mainly in this experiment. And then the copy paper were tested of the substanceweight and contact angle, and compared with the water resistance when the domestic water repellent agent or AKD was added alone. Conclusions of this experiment are following: the optimal conditions were that the mass ratio of AKD and CRS is 6:4, the additive level of AKD and the cationic rosin is 6% (based on dry weight of pulp), the quantity of the sizing synergist is 0.5% , and no oil resistance agent was added, the effect of water resistance is best.

High consistency refining (HCR) and low consistency refining (LCR) of unbleached Masson’s pine kraft pulps for sack paper were studied in this article. The properties of their refined pulp and handsheet were analyzed comparatively. The results showed a high consistency refining was more suitable for sack paper with unbleached Masson’s pine kraft pulp than a low consistency refining. High consistency refining is of advantage to retain the fiber length. The tear index of the handsheet of high consistency refining were higher than that of low consistency refining. The TtensileT TenergyT Tabsorption (TEA)T index and air permeability of the handsheet of high consistency refining which were crucial properties of sack papers were better, though higher tensile index could be obtained with low consistency refining.

Eco-friendly high-yield pulps (HYP) are becoming increasingly used to product high value-added fine paper that is traditionally produced exclusively with chemical pulps. However, due to the presence of a large quantity of photosensitive lignin in the HYP pulp to more effectively utilize woods resources, there is a concern on the long term brightness stability of HYP containing paper. In this research, various TiO2was added to coating colors to improve the light fastness properties of HYP containing coated paper. The effect on the stability of optical properties of coated paper including brightness, opacity, color difference and the degree of brightness reversion before and after accelerated aging were studied. It was shown that the brightness stability of the HYP containing coated paper increased with increased addition of TiO2. Rutile TiO2was especially more effective than other types of TiO2on yellowing inhibition of coated paper. At a dosage of 3 parts of rutile TiO2, the brightness stability of coated paper containing 20% of HYP was found to be even better than paper made of 100% chemical pulp coated with conventional coating color.

The intention of this paper is to review of some recent innovative novelties about paper and board pigment coating raw materials. First an overview is given of “traditional” coating raw materials and the coating process. Then new starch based pigments and binders as well as novel plastic pigments are reviewed regarding their effect on coated paper properties. Finally it is concluded that further innovations and research are needed.

To enhance printing qualities, this study used refluxed silica (SiO2) from rice husk by hydrochloric acid (HCl) at different molarities and reaction times as coating agent for printed paper. Characterization of the refluxed silica from 2M HCl 120 min elucidated the purity of 98.7% and amorphous structure. Particle size of the silica exhibited uniform size of 3 μm and the color measurement (CIE L*a*b*) indicated 94.79+0.48+1.24, whiteness and color difference (E) were 84.85, 3.28, respectively. The coating agent was prepared by water-based varnish of acrylic resin mixed with the synthesized silica at different proportions: 0.0, 0.5, 1.0, and 1.5 (%wt), and later was applied on 170 g/m2-white kraft papers. The results showed that the water-based coating varnish with silica exhibited an increase of viscosity as increasing the amount of the silica. Printing qualities indicated that the vanished printed paper with 1.0% silica elucidated the highest details in shadow tone and text (font) sharpness. The color gamut yielded a wider scope than the printed papers which were varnished with the silica at 0.0%, 0.5% and 1.5%. Nonetheless, the color density showed insignificant difference to 1.5% silica varnished paper.

Paper-based material has been frequently used as part of packaging solution as an option towards reducing municipal solid waste generation. Various studies on mechanical behaviour of paper-pulp packaging material have been conducted based on the machining direction and cross machining direction. However, there is still gap of information on paper-pulp packaging material behaviour at diagonal direction. A study has been conducted to investigate the variability to tensile properties of paper-pulp packaging at various packaging section (draft and base surface) and different specimen orientation (horizontal, vertical, and diagonal direction). In this research, results from the stress-strain relationship obtained from tensile and compression tests are presented. The data obtained are further analysed using ANOVA to find out whether material variations are significantly different with varying sections and orientations. Findings in this research supported the anisotropic properties of paper-based packaging material. Draft surfaces exhibit weaker strength than base surface. Also, the variability of stiffness and strength of specimens are more significant in horizontal and vertical direction compared to diagonal direction.

This paper experimentally examined the impact of four different drying methods (free drying, press drying, vacuum drying and impingement drying) on paper physical properties including roughness, elongation, air permeance, tearing resistance, tensile index and bursting strength. The handsheets materials are HWBKP (Hardwood Bleached Chemical Pulp), SWBKP (Softwood Bleached Chemical Pulp), CTMP (Chemical Thermo mechanical Pulp) and ATMP (Advanced Thermo Mechanical Pulp). Good experimental data were obtained for the four pulps under different drying conditions. The results of our investigation indicate that press drying have lower surface roughness, elongation and air permeance but higher tearing resistance; the vacuum drying have higher roughness, tensile index and bursting strength; the impingement drying have lower tearing resistance, tensile index and bursting strength but higher elongation and air permeance. Selection of different drying conditions for effective productivity and quality improvement potential is proposed as a direction for the future dryer design.

Low density printing paper was widely used in printing best-seller at present. Besides of high bulk, good stiffness, soft color, it also had some advantages, such as reducing user’s load, protecting eyes, extending the storage time etc. Quality index of domestic low density printing paper was lower than foreign index. The gap mainly expressed on tensile index specially. This study used Aspen BECMP as main pulp, as a result of its higher strength, lower cost and other advantages comparing with PRC-APMP. Here we discussed three pulps ratio to make low density printing paper. The results of experiment indicated that using Aspen BECMP was able to make low density printing paper by adding certain amount chemistry pulp. Moreover, the best bulk value can up to 2.45cm3/g, and the tensile index was 36.08Nm/g.

In this paper, we studied the possibility of wood powder in place of mechanical pulp in paper making to get high bulkness, also the dry-bleaching method of wood powder, the strength enhancement and retention effect for wood powder during paper making were all introduced and analyzed in detail.

The paper pulp compression molding material is one of the most commonly used materials in packing industry. Their mechanical properties attract attentions from professional visitors and researchers. It is a difficult work to test the mechanical properties as the paper pulps are thin, anisotropic and sometimes wet. To spray ink spots with the surface of the specimens is not allowed either. The digit image frequency correlation method (DIFC) is presented in the paper, the information carrier of the displacement is the nature texture on the tested surface. Image acquiring and analysis are accomplished by the CCD camera and computer. From the displacement field strain distributions were obtained and the mechanical properties of the paper pulp compression molding material were evaluated. The test system is simple and the sensitivity is adjustable. DIFC is approved a suitable test method for paper pulp compression molding material.

In is paper precipitated silica is used in coated paper coating. It shows that the effect of different silica on properties of pigment dispersion is different. The dosage of silica influences the properties of pigment dispersion too. The viscosity of coating is higher than the corresponding pigment dispersion. The higher the viscosity of pigment dispersion is, the higher the corresponding viscosity of coating is. The more the dosage of silica is and the littler the particle size of silica is, the larger water retention value of coating is. When the precipitated silica is used in coated paper coating, the viscosity of coating is increasing. If precipitated silica coat paper, the whiteness of coated paper increases by 1%-2%

The manufacturing process of particle composite for furniture, made of waste paper and wood particle, was studied and discussed in this paper, and an ornament cabinet and a Chinese style teapoy were assembled in the laboratory with the composite. The results showed the mechanical properties of composite made of waste paper, was low. Wood particle was blended with waste paper and made into composite, and the mechanical properties of the composite could meet the demand of particle board for furniture and ornament under the Chinese national standard. The application of waste paper-based composite was feasible technically.

The physical structure and chemical properties of coating layer have an important influence on transferring and setting of the printing ink. In this study, the effect of pigment on coating layer structure and surface properties was investigated. The surface topography was explored using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The findings indicated that the pigment affected the pore size, depth and distribution of the coated paper surface. The conclusions were drawn that coating could improve coating surface topography and calcium carbonate pigment compared with kaolin pigment was not good to the paper surface properties, which resulted in high roughness, low paper gloss, high ink absorption and low paper surface efficiency.

This paper uses the culture paper commonly-used filler PCC (precipitated calcium carbonate) and makes a good ratio of other raw materials and dosage of various other chemicals. Under the certain papermaking craft condition, with the certain quantum, the experiment changes the filler proportion of the paper to make paper samples and test the samples’ properties and the printing ink transfer.The experiment establishes an influence curve relationship, through that we analysis and draw the conclusion when the proportion of PCC is in the range 20% to 30%, it will get better ink transfer effect, which will provide reference for actual production.

In this paper, the effect of the charge of hydrophilic and lipophilic nanosized TiO2 on the optical properties and printability of coated paper was investigated. The parameters including brightness, opacity, surface strength and sizing degree were used to evaluate the optical properties and printability of coated paper. The effects of hydrophilic and lipophilic TiO2 on the properties of coated paper were discussed. It was shown that the optical properties and printability of coated paper increase persistently with the change of nanosized TiO2 charged from 5% to 15%. Once the charge of nanosized TiO2 was over 15%, the main properties of coated paper took on a downward tendency. The properties of coated paper were related to the surface properties of nanosized TiO2 samples. It was found that the lipophilicity of nanosized TiO2 sample played a more important role in the improvement of the coated paper properties, which was believed to be based on the fact that lipophilic nanosized TiO2 could be well compatible with the binders used in the paper coating.

By the preceding experiments, we concluded that the optimum conditions for laccase treatment were: the concentration of laccase 16U/g dry pulp, the pulp consistency 5%, temperature 50 °C, pH=5.0 and reaction time 90min. We studied the change of water retention value and carboxyl content changes under the best conditions. As well as we studied the effect of pulp strength properties by biological treatment combined with mechanical treatment. Moreover, environmental scanning microscope images showed that more collapse and more fibrillation were observed on the beating combined with laccasehistidine-treated fiber surface than the control samples, which led to form better bonding between fibers in handsheets resulting in the increase of the paper strength of beating combined with laccasehistidine-treated OCC pulp.

Preservative was very necessary used in coated paper coating. Preservative was typical paper additive which was low dosage and high yield. Preservative classification, function mechanism and application technology of coated paper coating was introduced and summarized by the numbers in this paper. Finally the development direction and prospect of preservative used in coated paper coating was prospected.

The performances of three kinds of water-based pigment inks were compared and studied, which include self-made ink, original printing ink and compatible ink. Art paper, matte paper and white card paper were used as the substrates. Testing the contact angle of ink droplets, the spreading, wetting, and drying rate of inks were investigated. The color density and CIE L*a*b* values of the printed samples were measured, to evaluate the hue error and color gamut. The water resistance was studied with corresponding experiments. The result indicates: self-made water-based pigment ink has the smallest contact angle on coated paper, showing a faster drying rate. Its color gamut is similar to the original printing ink on art paper, and the hue error is low. Through the water resistance test, the color density measured on art paper and matte paper had no changes, without color dissolving and color fading, showing good water resistance applicability.

Having been coated, the surface unevenness and pores on paper were covered by a coating layer composed of fine particles and binders, which can absorb ink well, thereby a good uniformity and smoothness of paper could be obtained, consequently, the reproducing capability for printing dot and good whiteness, gloss and opacity can be improved. In theory, the ink rub resistance for coated paper print is mainly affected by the ink absorbance property of paper, printing conditions, ink components, rub medium and so on. In this study, seven different kinds of coated papers, the viscosities of the inks were adjusted with a viscosity adjusting agent, and then the prints were prepared by proofing with the ink with different viscosities. After drying, the prints were used for rub testing. The impact of the basic properties of coated paper and the content of reducer in inks on rub resistance were discussed on the basis of a comparative analysis of the experimental data. Printing color density loss rate and print color difference were exploited in this paper to characterize the ink rub resistance for coated paper prints. In this study, it was found that ink rub resistance was mainly influenced by ink absorbency and smoothness of the paper. Under the similar conditions, the color density of coated paper print decreases with the rub strength increasing, color difference increased gradually, but not linearly. With the increase of ink viscosity reducer content, printing density loss rates as well as color difference changed, but not be linearly.