Search

The new power system effectively integrates a large number of distributed renewable energy sources, such as solar photovoltaic, wind energy, small hydropower, and biomass energy. This significantly reduces the reliance on fossil fuels and enhances the sustainability and environmental friendliness of energy supply. Compared to distribution networks in traditional power systems, the new-generation distribution network offers notable advantages in improving energy efficiency, reliability, environmental protection, and system flexibility, but it also faces a series of new challenges. These challenges include potential harmonic issues introduced by the widespread use of power electronic devices (such as inverters for renewable energy generation systems and electric vehicle charging stations) and the voltage fluctuations and flickering caused by the intermittency and uncertainty of renewable energy generation, which may affect the normal operation of electrical equipment. To address these challenges, this study proposes an optimization model aimed at minimizing network losses and voltage deviations, utilizing traditional capacitor adjustments and static var compensators (SVCs) as optimization measures. Furthermore, this study introduces an improved version of the multi-objective particle swarm optimization (MOPSO) algorithm, specifically enhanced to address the unique challenges of reactive power optimization in modern distribution networks. The test results show that this algorithm can effectively generate a large number of Pareto optimal solutions. The application of this algorithm on a 33-node network case study demonstrates its advantages in reactive power optimization. The optimization results highlight the effectiveness and feasibility of the proposed improved algorithm in the application of distribution network reactive power optimization, offering users a uniform and diverse range of reactive compensation solutions. [ABSTRACT FROM AUTHOR]

This paper proposes a novel methodology to improve stability in a transmission system under critical conditions of operation when additional loads that take the system to the verge of stability are placed in weak bus bars according to the fast voltage stability index (FVSI). This paper employs the Newton–Raphson method to calculate power flows accurately and, based on that information, correctly calculate the FVSI for every transmission line. First, the weakest transmission line is identified by considering N − 1 contingencies for the disconnection of transmission lines, and then all weak nodes associated with this transmission line are identified. Following this, critical scenarios generated by stochastically placed loads that will take the system to the verge of instability will be placed on the identified weak nodes. Then, the methodology will optimally size and place a single static VAR compensator SVC in the system to take the transmission system to the conditions before the additional loads are connected. Finally, the methodology will be validated by testing the system for critical contingencies when any transmission line associated with the weak nodes is disconnected. As a result, this paper's methodology found a single SVC that will improve the system's stability and voltage profiles to similar values when the additional loads are not connected and even before contingencies occur. The methodology is validated on three transmission systems: IEEE 14, 30, and 118 bus bars. [ABSTRACT FROM AUTHOR]

Flexible alternating current transmission systems (FACTSs) have been widely incorporated in electric power systems in order to control system parameters. This paper proposes the modeling of four FACTS devices, using the Branch Flow Model (BF) as an optimization problem to reduce the complexity of the Newton–Raphson (NR) load flow code with FACTS devices. The devices are represented as variable impedances, as a function of a firing angle, and as voltage source converters (VSCs) located on the buses and transmission lines. This proposed model solves the problem associated with the selection of appropriate initial conditions of the parameters of each device that guarantee convergence. The model is validated by evaluating its percentage deviation with respect to the NR method, using the standard test systems, IEEE 5-bus, IEEE 14-bus, IEEE 30-bus, and IEEE 57-bus systems. [ABSTRACT FROM AUTHOR]

This study aimed to optimize the incorporation of static var compensators (SVCs) into Oman's main interconnected system (MIS) using real 2023 MIS data. Leveraging the particle swarm optimization (PSO) algorithm within MATLAB, substantial enhancements were achieved in voltage profiles, with associated losses reducing by roughly 2%. A multi-objective strategy effectively managed costs while preserving improved voltage profiles and controlled losses. Validation through DigSILENT showcased the dynamic advantages of optimal SVC placement through consistently elevating voltage profiles and mitigating losses, notably within the Muscat region. Analyses encompassing harmonics, transient stability, and load distribution indicated that harmonics remained within acceptable thresholds, and overall system stability was enhanced. Optimal SVC deployment expedited the attainment of steady-state conditions, as illustrated via the QV curve, demonstrating increased stability as the buses loaded from 18% to 96%. These findings underscore the robust and efficient nature of SVC integration as a viable solution within Oman's MIS system, addressing voltage profile enhancement, loss minimization, and fortified system stability. [ABSTRACT FROM AUTHOR]

This article presents the comparison of 3D and 2D finite element models of a power transformer designed for reactive power compensation stations. There is a lack of studies in the literature on internal electromagnetic phenomena in the active part of a transformer operated in these conditions. The results of numerical 2D and 3D calculations of no-load current and losses in the transformer core were obtained by using various methods and models. The impact of considering the hysteresis loop phenomenon on the calculation of core losses was investigated by using the Jiles–Atherton core losses model. The results obtained in the paper show that the model of the core must contain the areas representing the influence of overlappings on the no-load current and also on the flux density field in the core. The capacitive load of the transformer increases the flux density in the core limbs by several percent, so the power losses there must also increase accordingly. As a summary of the research, differences in the values of losses in each core element between the capacitive load and no-load conditions are presented. The results presented in this paper indicate that considering nonlinearity related to the magnetic hysteresis loop has a significant impact on the calculation of the core losses of power transformers. [ABSTRACT FROM AUTHOR]

An electrical power system (EPS) is subject to unexpected events that might cause the outage of elements such as transformers, generators, and transmission lines. For this reason, the EPS should be able to withstand the failure of one of these elements without changing its operational characteristics; this operativity functionality is called N − 1 contingency. This paper proposes a methodology for the optimal location and sizing of a parallel static Var compensator (SVC) in an EPS to reestablish the stability conditions of the system before N − 1 contingencies take place. The system's stability is analyzed using the fast voltage stability index (FVSI) criterion, and the optimal SVC is determined by also considering the lowest possible cost. This research considers N − 1 contingencies involving the disconnection of transmission lines. Then, the methodology analyzes every scenario in which a transmission line is disconnected. For every one of them, the algorithm finds the weakest transmission line by comparing FVSI values (the higher the FVSI, the closer the transmission line is to instability); afterward, when the weakest line is selected, by brute force, an SVC with values of 5 Mvar to 100 Mvars in steps of 5 Mvar is applied to the sending bus bar of this transmission line. Then, the SVC value capable of reestablishing each line's FVSI to its pre-contingency value while also reestablishing each bus-bar's voltage profile and having the lowest cost is selected as the optimal solution. The proposed methodology was tested on IEEE 14, 30, and 118 bus bars as case studies and was capable of reestablishing the FVSI in each contingency to its value prior to the outage, which indicates that the algorithm performs with 100% accuracy. Additionally, voltage profiles were also reestablished to their pre-contingency values, and in some cases, they were even higher than the original values. Finally, these results were achieved with a single solution for a unique SVC located in one bus bar that is capable of reestablishing operational conditions under all possible contingency scenarios. [ABSTRACT FROM AUTHOR]

Given the concern for maintaining voltage stability in power systems integrated with renewable power systems due to a mismatch in generation and demand, there remains a need to invoke flexible alternating current transmission system (FACTS) devices in the distribution network. The present paper deals with identifying the locations of placement of a static var compensator in an experimental IEEE 14-bus system; the voltage drop in different buses in an IEEE 14-bus system is calculated by the standard formula. The total voltage drop in the network (TVDN) is also calculated as a reference. The ranking of buses in order of decreasing voltage drop is made, and the weak buses are identified as those showing the maximum or near-maximum voltage drop for the installation of a Static Var Compensator (SVC). The optimum usable size is calculated using a Genetic Algorithm approach to optimize the installation cost. After size optimization, installing a 2 MW solar generator is considered for the weak and most potential bus, which suffers from voltage drops or power loss. Based on the generator at the weakest bus, the total power loss in the network is calculated and compared with a similar method to assess the efficiency of the proposed model. Thus, the voltage stability enhancement problem is solved by applying a Genetic algorithm (GA) to optimize SVC size and using the Total Voltage Drop in Network (TVDN) method to identify weak buses in the systems. It is found that the performance of the proposed system is comparable with another existing system. It is further observed that a gain in power loss to 6.56% is achievable by adopting the proposed strategy, and the gain is better than the other system. [ABSTRACT FROM AUTHOR]

The strategic intent of the African Union is to develop a "Smart Integrated African Electric Power Super Grid" driven by modern tools and advances in high-voltage direct current (HVDC) engineering and flexible alternating current technology systems (FACTS), which is central in supporting Africa's sustained economic growth and development. The southern African region, including South Africa, is beset by the critical challenges of perennial load-shedding, which impedes economic growth and aggravates unemployment. This has led to the insecurity of electricity supplies and degraded the quality of life. The parallel operation of high-voltage direct current (HVDC) and flexible AC technology systems (FACTS) controllers is gaining traction as system conditions become more complex, such as weak power networks which requires increased stability requirements, resulting in load-shedding and power outages. These adversely affect business productivity and adversely affect GDP and economic growth. Thus, the application of innovative technologies such as HVDC links can stabilize weak power systems. It is established that HVDC delivery systems reduce losses in long transmission lines transporting bulk power compared with high-voltage alternating current (HVAC) transmission lines for power wheeling. This paper evaluates the parallel operation of the Cahora Bassa 1414 km bipolar HVDC link and a weak parallel 400/330 kV alternating current (AC) link. It demonstrates the use of FACTS controllers to enhance the technical performance of an existing network, such as voltage control, and technical loss reduction. It combines an HVDC line commutated converter (LCC) and HVAC transmission lines, in hybrid notation to increase the voltage stability of the system by controlling the reactive power with a Static Var Compensator (SVC). These modern tools can increase the transmission power controllability and stability of the power network. In this study, HVDC–LCC was used with a setpoint of 1000 MW in conjunction with the 850 MVAr SVC. The results show that the technical losses were reduced by 0.24% from 84.32 MW to 60.32 MW as Apollo 275 kV SVC was utilized for voltage control. The network analysis was performed using DIgSILENT PowerFactory software that is manufactured by DIgSILENT GmbH at Gomaringen, Germany [ABSTRACT FROM AUTHOR]

Reliability and safety must be carefully considered in today's power systems, which are rapidly evolving toward ever higher penetration of renewable, inverter-based generation units. Power systems are constantly stressed by active power disturbances, which can be exacerbated by wind and solar systems that are subject to rapid fluctuations in primary energy. In this framework, a comparative technical analysis of solutions to improve transient stability, both rotor angle stability and frequency stability, is carried out. These solutions can be adopted by the transmission system operator (e.g., an additional parallel transmission line), by the generation companies (e.g., a fast excitation system), or by both, such as SVC (static VAR compensator) and STATCOM (static synchronous compensator). Sensitivity analyses were carried out to assess the impact of the location of the wind turbines in the buses of the grid on their rated power and level of production. On the basis of these analyses, the worst-case fault was considered, and the critical fault recovery time was determined as an engineering parameter to compare the different solutions. For the numerical analysis, a modified IEEE 9-bus system was considered, and the PowerWorld software tool was used. Rotor angle and frequency stability analyses were performed. [ABSTRACT FROM AUTHOR]

The adoption of a DFIGs generator in a WECs is characterized by several advantages: robust and flexible system, energy generation in a wide operating range of wind turbines, simplicity of the control system and cost-efficient operation. Despite most DFIG control strategies discussed in literature refer to a nominal operating condition, a smooth startup procedure must be also envisioned to avoid high transient currents in the stator windings resulting from excessive mismatch between grid and open-stator voltages. Most DFIG control schemes rely on the integration of the stator voltage equation to estimate the stator flux vector for the needed d-q frame orientation. [Extracted from the article]

Developing control methods that have the ability to preserve the stability and optimum operation of a wind energy generation unit connected to power systems constitutes an essential area of recent research in power systems control. The present work investigates a novel control of a wind energy system connected to a power system through a static VAR compensator (SVC). This advanced control is constructed via integration between the model predictive control (MPC) and an artificial neural network (ANN) to collect all of their advantages. The conventional MPC needs a high computational effort, or it can cause difficulties in implementation. These difficulties can be eliminated by using Laguerre-based MPC (LMPC). The ANN has high performance in optimization and modeling, but it is limited in improving dynamic performance. Conversely, MPC operation improves dynamic performance. The integration between ANN and LMPC increases the ability of the Neuro-MPC (LMPC-ANN) control system to conduct smooth tracking, overshoot reduction, optimization, and modeling. The new control scheme has strong, robust properties. Additionally, it can be applied to uncertainties and disturbances which result from high levels of wind speed variation. For comparison purposes, the performance of the studied system is estimated at different levels of wind speed based on different strategies, which are ANN only, Conventional MPC strategy, MPC-LQG strategy, ANN- LQG strategy, and the proposed control. This comparison proved the superiority of the proposed controller (LMPC-ANN) for improving the dynamic response where it mitigates wind fluctuation effects while maintaining the power generated and generator terminal voltage at optimum values. [ABSTRACT FROM AUTHOR]

Worldwide, due to the abrupt growth of population, the load demand has been rising dramatically in the last few years. This led to an increase in branch overloads, voltage deviations, and power losses. These problems may result in line outages or the occurrence of blackouts. Flexible AC transmission system (FACTS) devices can be installed in the power system to ensure increased power flow capability and flexible voltage control to address these issues. In this paper, one of the most used FACTS is utilised. It is called Static VAR Compensator (SVC). This controller is one of the most commonly used shunt FACTS controllers due to its low cost in comparison to others, ease of operation, and integration into the power grid. Two Optimization algorithms are combined to form a hybrid optimization approach: Cuckoo Search (CS) and Antlion Optimization (ALO). This hybrid approach employs the exploration of ALO to adjust the optimum allocation and size for SVCs in the power system. This study proposes the IEEE 57 bus scheme as a fairly large structure, with the 50 and 41 branch outages considered the worst-case scenarios for line outages in this system. The simulation results show that the proposed methodology balances exploring the research space and exploiting the best existing solutions compared to some of the other introduced approaches in the literature. [ABSTRACT FROM AUTHOR]

A constant worldwide growing load stress over a power system compelled the practice of a reactive power injection to ensure an efficient power network. For this purpose, multiple technologies exist in the knowledge market out of which this paper emphasizes the usage of the flexible alternating current transmission system (FACTS) and presents a comparative study of the static var compensator (SVC) with the static synchronous compensator (STATCOM), inducted in a real electric substation. The aim is to improve the power factor (PF) and power quality and to encounter reliably extreme conditions. A 220 kV electric substation was opted for the analysis, and both the static and dynamic conditions were observed with the help of a power system analysis tool termed PowerFactory-DIgSILENT. Multiple aspects were investigated via software simulations to assess the performance of the aforementioned FACTS devices, such as the voltage profile evaluation via the load flow analysis method (LFA), the harmonic response via the power quality and harmonic analysis tool, and the short-circuit response via the RMS simulation tool. The outcomes were verified and compared with permissible values included in the universal standards, such as IEC and IEEE. The superiority of the STATCOM over the SVC was proven in light of the simulative results. [ABSTRACT FROM AUTHOR]

In order to solve the reactive power and voltage control problem caused by the high proportion of new energy connected to the power grid, this paper takes the minimum voltage deviation, minimum network loss and maximum dynamic reactive power margin of the whole system as the comprehensive optimization objectives and establishes a reactive power and voltage optimization model by considering the reactive power regulation ability of SVC (Static Var Compensator) and new energy units. In view of the continuous and discrete variables in the model, the traditional continuous FPA (Flower Pollination Algorithm) is discretized to form an improved continuous-discrete hybrid FPA, and the tournament selection mechanism is adopted to speed up the convergence. Through the example analysis of the IEEE-39 bus system, the feasibility of the proposed reactive power and voltage optimal control method in the new energy grid is verified. Compared with GA (Genetic Algorithm), the results show that the improved FPA has high optimization accuracy, which is suitable for solving the reactive power and voltage optimization problem of the new energy grid. [ABSTRACT FROM AUTHOR]

Voltage sag in a power system is an unavoidable power quality issue, and it is also an urgent concern of sensitive industrial users. To ensure the power quality demand and economical operation of the power system, voltage sag management has always drawn great attention from researchers around the world. The latest research that realizes the power quality conditioning has used dynamic voltage restorers (DVRs), static VAR compensator (SVCs), adaptive neuro-fuzzy inference systems (ANFISs), and fuzzy logic controllers based on DVR to mitigate voltage sag. These devices, methods, and control strategies that have been recently used for voltage sag mitigation have some limitations, including high cost, increased complexity, and lower performance. This article proposes a novel, efficient, reliable, and cost-effective voltage sag mitigation scheme based on a modular multilevel converter (MMC) that ensures effective power delivery at nominal power under transient voltage conditions. The proposed method, the MMC, compensates for the energy loss caused by voltage sags using its internal energy storage of the submodules, and ensures reliable power delivery to the load distribution system. Furthermore, control strategies are developed for the MMC to control DC voltage, AC voltage, active power, and circulating current. Detailed system mathematical models of controllers are developed in the dual synchronous reference frame (DSRF). Validation of the results of back-to-back MMC for dynamic load distribution system is analyzed which proves the effectiveness of the proposed scheme for voltage sag mitigation. [ABSTRACT FROM AUTHOR]

This paper proposes a novel hybrid algorithm combining chaotic Jaya (CJaya) and sequential quadratic programming (SQP), namely CJaya-SQP, for solving the coordinated design problem of static var compensator (SVC) and power system stabilizers (PSSs). The CJaya serves as a global optimizer and the SQP as a local optimizer for fine-tuning the solution. In the proposed algorithm, chaotic maps are used to generate the initial solutions and control the search process. In order to prove the performance of the CJaya-SQP, a set of benchmark optimization problems is used where the results are compared with those of the basic Jaya and other recognized algorithms. The proposed optimization method is then applied for the optimal tuning of PSSs and SVC controllers in such a way that damping ratios and damping factors of the electromechanical modes are optimally improved. To illustrate the robustness of the CJaya-SQP-based coordinated PSSs and SVC controllers, the four-machine, two-area system is used. Eigenvalue analysis and nonlinear time-domain simulation vividly show that the CJaya-SQP-based coordinated controllers improve greatly the system's dynamic stability with a robust damping of local and inter-area power oscillations. [ABSTRACT FROM AUTHOR]

This paper presents an improved Teaching-Learning-Based Optimization (TLBO) for optimal tuning of power system stabilizers (PSSs) and static VAR compensator (SVC)-based controllers. The original TLBO is characterized by easy implementation and is mainly free of control parameters. Unfortunately, TLBO may suffer from population diversity losses in some cases, leading to local optimum and premature convergence. In this study, three approaches are considered for improving the original TLBO (i) randomness improvement, (ii) three new mutation strategies (iii) hyperchaotic perturbation strategy. In the first approach, all random numbers in the original TLBO are substituted by the hyperchaotic map sequence to boost exploration capability. In the second approach, three mutations are carried out to explore a new promising search space. The obtained solution is further improved in the third strategy by implementing a new perturbation equation. The proposed HTLBO was evaluated with 26 test functions. The obtained results show that HTLBO outperforms the TBLO algorithm and some state-of-the-art algorithms in robustness and accuracy in almost all experiments. Moreover, the efficacy of the proposed HTLBO is justified by involving it in the power system stability problem. The results consist of the Integral of Absolute Error (ITAE) and eigenvalue analysis of electromechanical modes demonstrate the superiority and the potential of the proposed HTLBO based PSSs and SVC controllers over a wide range of operating conditions. Besides, the advantage of the proposed coordination design controllers was confirmed by comparing them to PSSs and SVC tuned individually. [ABSTRACT FROM AUTHOR]

In this research, an alternative methodology is proposed for the location of Static VAR Compensators (SVC) in power systems, considering the reconfiguration of reactive power flows through the optimal switching of the transmission stage, which resembles the contingency restriction N-1 usually considered in transmission expansion planning. Based on this methodology, the contingency index was determined, which made it possible to determine which is the contingency that generates the greatest voltage degradation in the system. For the quantification of reactive flows, optimal AC power flows were used, which minimize the operating costs of the power system subject to transmission line switching restrictions, line charge-ability, voltages and node angles. To determine the node in which the compensation should be placed, the contingency index criterion was used, verifying the voltage profile in the nodes. The proposed methodology was tested in the IEEE test systems of 9, 14 nodes and large-scale systems of 200, 500 and 2000 bus-bars; to verify that the proposed methodology is adequate, the stability of the EPS was verified. Finally, the model allows satisfactorily to determine the node in which the SVC is implemented and its compensation value. [ABSTRACT FROM AUTHOR]

Distributed generators providing auxiliary service are an important means of guaranteeing the safe and economic operation of a distribution system. In this paper, considering an energy storage system (ESS), switchable capacitor reactor (SCR), step voltage regulator (SVR), and a static VAR compensator (SVC), a two-stage multi-period hybrid integer second-order cone programming (SOCP) robust model with partial DGs providing auxiliary service is developed. If the conic relaxation is not exact, a sequential SOCP is formulated using convex–concave procedure (CCP) and cuts, which can be quickly solved. Moreover, the exact solution of the original problem can be recovered. Furthermore, in view of the shortcomings of the large computer storage capacity and slow computational rate for the column and constraint generation (CCG) method, a method direct iteratively solving the master and sub-problem is proposed. Increases to variables and constraints to solve the master problem are not needed. For the sub-problem, only the model of each single time period needs to be solved. Then, their objective function values are accumulated, and the worst scenarios of each time period are concatenated. As an outcome, a large amount of storage memory is saved and the computational efficiency is greatly enhanced. The capability of the proposed method is validated with three simulation cases. [ABSTRACT FROM AUTHOR]