Search

The development of wind power has brought about increasing challenges in decommissioning, among which DWTBs (decommissioned wind turbine blades) are the most difficult component to deal with. To enable the cost-effective, energy-efficient, and environmentally friendly large-scale utilization of DWTBs, an experimental study on thermogravimetric and pyrolysis characteristics of DWTBs was carried out. A new process involving recycling glass fiber with pyrolysis gas re-combustion and flue gas recirculation as the pyrolysis medium was innovatively proposed, and the simulation calculation was carried out. Thermogravimetric experiments indicated that glass fiber reinforced composite (GFRC) was the main heat-generating part in the heat utilization process of blades, and the blade material could basically complete pyrolysis at 600 °C. As the heating rate increased, the formation temperature, peak concentration, and proportion of combustible gas in the pyrolysis gas also increased. The highest peak concentration of CO gas was observed, with CO2 and C3H6 reaching their peaks at 700 °C. The solid product obtained from pyrolysis at 600 °C could be oxidized at 550 °C for 40 min to obtain clean glass fiber. And the pyrolysis temperature increased with the increase in the proportion of recirculation flue gas. When the proportion of recirculation flue gas was 66%, the pyrolysis temperature could reach 600 °C, meeting the necessary pyrolysis temperature for wind turbine blade materials. The above research provided fundamental data support for further exploration on high-value-added recycling of DWTBs. [ABSTRACT FROM AUTHOR]

Dry-type air-core shunt reactors are integral components in power transmission and distribution networks, designed to control reactive power and enhance system stability. However, inter-turn short-circuit faults (ISCFs) are common occurrences in shunt reactors, which are caused by various factors, including manufacturing defects, insulation degradation, or operational stresses. At the early stage of the ISCFs, the current does not reach a sufficient level to activate the protective equipment. These faults may lead to serious consequences, such as overheating, insulation breakdown, and even catastrophic failures, posing risks to the entire power system. Therefore, developing an effective and reliable detection method for ISCFs at the early stage is paramount. In this paper, a new method named the fault detection factor (FDF) based on equivalent resistance is presented to detect the slight ISCFs in dry-type air-core shunt reactors considering insulation resistance. In addition, the effect of noise signal existence in the monitoring process is taken into account. A moving average filter is adopted to guarantee both the sensitivity and the reliability of the proposed method. Ultimately, the simulation results of the FDF under different conditions are presented, which show the effectiveness and potential of the proposed method in observing and monitoring slight ISCFs. [ABSTRACT FROM AUTHOR]

With the rapid development of the new energy vehicle industry, the number of power battery decommissioning is increasing year by year. The recycling of power batteries is of great significance for protecting the ecological environment, improving the efficiency of resource utilization, and ensuring the sustainable and healthy development of the new energy automobile industry. In this study, the chemical compositions of power batteries were introduced, the technical path and development status of the echelon utilization of decommissioned power batteries were discussed, and the specific steps and challenges of regenerative utilization of decommissioned power batteries were described in detail from two aspects of pyrometallurgy and hydrometallurgy. Combined with the relevant research results, the main methods of the direct regeneration of positive electrode materials were analyzed. Finally, the main development direction and related suggestions for the resource utilization of decommissioned power batteries were put forward. [ABSTRACT FROM AUTHOR]

This study utilized a combination of FLIC(1D3.2C) and FLUENT(2021R2) software to optimize the primary air distribution along the grate and the performance of a straw briquette combustion furnace of a 7 MW unit in China used to produce hot air for drying grain. Three air distribution modes, namely front-enhanced, uniform, and rear-enhanced modes, were analyzed to determine their effect on the flue gas components above the grate, the temperature field in the furnace, and the nitrogen oxide concentration at the furnace outlet. The results of the calculations showed that the NOx emissions for the front-enhanced, uniform, and rear-enhanced modes were 133.5 mg/Nm3, 104.4 mg/Nm3, and 76.6 mg/Nm3, respectively. It was found that the rear-enhanced mode can expand the biomass drying, devolatilization, and combustion zone, thus improving the furnace combustion performance and decreasing NOx emissions. These findings can provide useful guidance for optimizing biomass chain-grate-firing furnaces. [ABSTRACT FROM AUTHOR]

A reactor is an important piece of equipment used for reactive power compensation in power system and has a significant impact on the safe operation of power system. Thermal behavior is one of the main causes of reactor failures. For an accurate analysis of the thermal behavior of reactors, electromagnetic–thermal–fluid multi-physics coupling modeling is chosen. However, there is a huge difference in size between the overall structure of the reactor and its insulating material, which makes it difficult to perform mesh generation, resulting in dense mesh and significantly increased solution degrees of freedom, thus making the solution of the reactor's multi-physics field model very time-consuming. To address this, this paper proposes a simplified processing method to accelerate the solution calculation of the reactor's multi-physics model. This method calculates the equivalent turns of each encapsulate with parallel coils in the reactor, simplifying the encapsulate into a single-layer coil, thereby greatly reducing the division and solution degrees of freedom of the multi-physics model, and thus accelerating the simulation calculation. Taking a BKDCKL-20000/35 dry-type air-core shunt reactor as an example, the outer diameter of the coil is nearly 12,000 times bigger than the coil insulation, which is a huge size difference. Both refined models and simplified models are established. Compared to the simulation results of the detailed model, the simplified model demonstrates good accuracy; the maximum relative error of temperature is just 2.19%. Meanwhile, the computational time of the simplified model is reduced by 35.7%, which shows promising effectiveness and significant potential for applying the optimization design and operation prediction of dry-type air-core shunt reactors for enhanced thermal performance. [ABSTRACT FROM AUTHOR]

Ultra-supercritical circulating fluidized bed (CFB) boiler combustion technology has the advantages of environmental protection and good commercialization. As one of the key aspects in ultra-supercritical CFB combustion technology, the water wall system directly determines whether the CFB boiler can safely and effectively transform heat energy. This paper studies the thermal–hydraulic characteristics of the designed water wall system of a 700 MWe ultra-supercritical CFB boiler, the largest one that will be built next year. At four loads of the water wall system, hydrodynamic parameters are calculated based on the successfully verified mathematical models. The results show that the hydrodynamic characteristics of the system are good. The temperature distribution of the working fluid and metal of the water wall system is acceptable and safe at each load, which can support the technical development and improvement of the 700 MWe ultra-supercritical CFB boiler. [ABSTRACT FROM AUTHOR]

Thermal energy storage is an essential technology for improving the utilization rate of solar energy and the energy efficiency of industrial processes. Heat storage and release by the dehydration and rehydration of Ca(OH)2 are hot topics in thermochemical heat storage. Previous studies have described different methods for improving the thermodynamic, kinetic, and structural stability of Ca(OH)2 to improve energy storage density, energy storage rate, and cycle stability, respectively. Here, the mechanisms and effects of different techniques on the performance improvement of Ca(OH)2 and some common problems were reviewed. Specific problems were also clarified based on the characteristics of different technologies. Finally, suggestions for the future development of Ca(OH)2 heat storage materials were provided. [ABSTRACT FROM AUTHOR]

Ultra-supercritical circulating fluidized bed (CFB) boilers are taking up an increasing proportion of the CFB boiler fleet in China, making the safety concern about the heating surfaces in this type of boilers under sudden electricity failure draw more and more attention from the industry. For the time being, however, few studies have made efforts to resolve this concern. Given this, the physical process in a 660 MW ultra-supercritical boiler during the electricity failure accident was precited with a comprehensive model composed of mass and energy conservation equations in this work. The tube temperature of the boiler components with the highest safety risk, i.e., the water wall and a superheater, was obtained to evaluate the safety of the heating surfaces. The results revealed that the tube temperature (about 516 °C and 544 °C) would be obviously lower than the maximum permissible temperature of the tube material (600 °C and 630 °C) even when electricity could be restored at the power plant, indicating that the heating surfaces in the 660 MW ultra-supercritical CFB boilers would generally be recognized to be safe under sudden electricity failure. [ABSTRACT FROM AUTHOR]

RM (red mud), which comes from the Bayer process, has a huge annual output and is harmful to the environment. Because of the high iron content in RM, the process of iron recovery from RM can reduce the amount of RM well and create economic benefits, so it is a promising process. The paper focuses on the review on the research of the iron recovery method from RM, which includes the physical recovery method, chemical recovery method and emerging recovery method. By comparing the advantages and disadvantages of these processes, it is concluded that the fluidized bed reduction is a promising process that can be rapidly applied to the industry, but it still needs more investigation to overcome the current technical difficulties in the near future. [ABSTRACT FROM AUTHOR]

Compared with planar-type solid oxide fuel cells (SOFCs), mono-block-layer build (MOLB)-type SOFCs have additional three-phase boundaries per unit volume, and their performance is severely limited by their longer current path. To resolve this issue, a vertical rib design, which was evaluated using a numerical method, was proposed. Compared with the conventional design, the power density for the vertical rib design increased by 12.32%. This is because the vertical rib design provides another short path for current, which not only reduces the ohmic loss in the cathode, but also decreases the ohmic polarization caused by the contact resistance. However, the vertical rib design hinders the transport of oxygen in the cathode and increases the concentration loss. Therefore, the vertical rib size design is crucial. Based on the influence of the vertical rib width, the vertical rib widths on the cathode and anode sides of 0.7 and 1 mm are recommended for different contact resistances, respectively. [ABSTRACT FROM AUTHOR]

Solid circulation rate (Gs) represents the mass flux of circulating particles in circulating fluidized bed (CFB) systems and is a significant parameter for the design and operation of CFB reactors. Many measuring technologies for Gs have been proposed, though few of them can be applied in industrial units. This paper presents a comprehensive study on measuring technologies, and the results indicate that though the accumulation method is most widely applied, it is constrained by the disturbance of normal particle circulation. Some publications have proposed mathematic models based on pressure drop or other parameters to establish Gs measurement models; these necessitate the accurate modeling of complicated gas-solid flows in industrial devices. Methods based on certain measurement devices to specify parameters like velocity require device endurance in the industrial operation environment and stable local gas-solid flow. The Gs measuring technologies are strongly influenced by local gas-solid flow states, and the packed bed flow in standpipes make the bottom of standpipes an ideal place to realize Gs measurement. [ABSTRACT FROM AUTHOR]

As a clean fuel combustion technology, the circulating fluidized bed (CFB) has been developed rapidly in recent years, but one of its disadvantages is high N2O emissions. With the implementation of increasingly strict pollution control standards, N2O decomposition and removal technologies have become the main focus of current research. This paper reviews the latest research on noble metals, metal oxides, the molecular sieve and other new catalysts and decomposition methods for N2O removal. The research methods and functions of catalysts are compared and the existing problems are summarized. The future directions of development in N2O decomposition and removal are considered. Noble metals and the molecular sieve show satisfactory activity at relatively low temperatures, but their catalytic efficiency is obviously hindered by O2, NO and H2O. In addition, high costs and insufficient thermal stability limit their widespread industrial application. The metal oxide catalytic technology, especially oxygen carrier-aided combustion (OCAC), is expected to be the ideal method for N2O removal in CFB boilers due to its stability and economical feasibility. [ABSTRACT FROM AUTHOR]

Wet flue gas desulfurization (WFGD) wastewater treatment is a key problem in coal-fired plants. Traditional chemical precipitation methods cannot reach zero-liquid discharge (ZLD). In this paper, a new technology using the low-rank heat from flue gas to concentrate the wastewater for ZLD is proposed. A scrubber was built to verify the concentrating process, and the characteristics of the concentrated water were analyzed. The concentrated water was neutralized by adding Ca(OH)2 to raise the pH value. The wastewater can be concentrated 10~25 times to reduce the flow rate. The characteristics of the concentrated wastewater were studied by dosing lime. Then, liquid and solids were separated by filter pressing, the liquid was mainly composed of CaCl2, which accounts for 73.6%. The sludge is composed of CaSO4 and Mg(OH)2, depending on the lime consumption of the dosing process. Finally, the filter liquor after the filter press was mixed with ash to reach zero liquid discharge, and the sludge could be burnt after mixing with the coal or disposed by third-part vendor. This technology is demonstrated in one 600 MW unit and shows a high system reliability. The clean water is recycled by the WFGD wastewater during the evaporation. Binding on the environmental policies and large market demand of the WFGD wastewater, this technology shows a great application prospect in the future. [ABSTRACT FROM AUTHOR]

When the load of Circulating Fluidized Bed (CFB) boiler changes dynamically, the accumulation and consumption of residual char causes a large inertia and hysteresis in the boiler combustion system. Therefore, accurate estimation of the residual char in the boiler is of great significance to the control system and improve the combustion efficiency. Based on the Computational Particles Fluid Dynamics (CPFD) method, a numerical simulation of the variable load process of CFB boiler was carried out, and the dynamic changes of the residual char inventory were analyzed by combining the coal feed, ash discharge, and furnace calorific value. The results showed that after CFB boiler reached stable operation, the residual char fluctuated from 11,000 kg to 16,000 kg, accounting for about 3.7% of the total bed material, and the residual char was in a dynamic balance. During the load-up phase, the average residual char was 17,500 kg, and during the load-down phase, the average residual char was 15,000 kg. In the process of load dynamic change, reasonable residual char stock can ensure the boiler load from one steady state to another steady state rapid transition. [ABSTRACT FROM AUTHOR]

After the implementation of the ultra-low emissions regulation on the coal-fired power plants in China, the problem of the excessive ammonia-slipping from selective catalytic reduction (SCR) seems to be more severe. This paper analyzes the operating statistics of the coal-fired plants including 300 MW/600 MW/1000-MW units. Statistics data show that the phenomenon of the excessive ammonia-slipping is widespread. The average excessive rate is over 110%, while in the small units the value is even higher. A field test data of nine power plants showed that excessive ammonia-slipping at the outlet of SCR decreased following the flue-gas process. After most ammonia reduced by the dust collector and the wet flue-gas desulfurization (FGD), the ammonia emission at the stack was extremely low. At same time, a method based on probability distribution is proposed in this paper to describe the relationship between the NH3/NOX distribution deviation and the De–NOX efficiency/ammonia-slipping. This paper also did some original work to solve the ammonia-slipping problem. A real-time self-feedback ammonia injection technology using neural network algorithm to predict and moderate the ammonia distribution is proposed to decrease the NH3/NOX deviation and excessive ammonia-slipping. The technology is demonstrated in a 600-MW unit and works successfully. The excessive ammonia-slipping problem is well controlled after the implementation of the technology. [ABSTRACT FROM AUTHOR]

Due to their inherent advantages such as low cost, robustness and wide speed range, switched reluctance machines (SRMs) have attracted great attention in electrical vehicles. However, the vibration and noise problems of SRMs limit their application in the automotive industry because of the negative impact on driver and passengers' comfort. In this paper, a new control method is proposed to improve the vibratory and acoustic behavior of SRMs. Two additional control blocks —direct force control (DFC) and reference current adapter (RCA)—are introduced to the conventional control method (average torque control (ATC)) of SRM. DFC is adopted to control the radial force in the teeth of the stator, since the dynamic of the radial force has a large impact on the vibratory performance. RCA is proposed to handle the trade-off between the DFC and ATC. It produces an auto-tuning current reference to update the reference current automatically depending on the control requirement. The effectiveness of the proposed control strategy is verified by experimental results under both steady and transient condition. The results show that the proposed method improves the acoustic performance of the SRM and maintains the dynamic response of it, which proves the potential of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Due to the randomness of the intermittent distributed energy output and load demand of a micro-energy-grid, micro-sources cannot fully follow the day-ahead micro-energy-grid optimal dispatching plan. Therefore, a micro-energy-grid is difficult to operate steadily and is challenging to include in the response dispatch of a distribution network. In view of the above problems, this paper proposes an integrated optimal dispatch method for a micro-energy-grid based on model predictive control. In the day-ahead optimal dispatch, an optimal dispatch model of a micro-energy-grid is built taking the daily minimum operating cost as the objective function, and the optimal output curve of each micro-source of the next day per hour is obtained. In the real-time dispatch, rolling optimization of the day-ahead optimal dispatching plan is implemented based on model predictive control theory. The real-time state of the system is sampled, and feedback correction of the system is implemented. The influence of uncertain factors in the system is eliminated to ensure steady operation of the system. Finally, the validity and feasibility of the integrated optimal dispatching method are verified by a case simulation analysis. [ABSTRACT FROM AUTHOR]