Search

In this paper, the adaptive fuzzy control of switched stochastic nonlinear systems with set-time prescribed performance based on event-driven mechanism is studied. The creative part of this paper is that based on the set-time performance function, a modified event-triggered strategy that considers asynchronous switching to deteriorate system performance without strict assumptions is presented, which avoids Zeno behavior and saves communication resources. Then, by using backstepping recursive design technique, It $\hat {o}$ ’s differential lemma and mode-dependent average dwell time (MDADT) method, a novel adaptive performance control scheme is proposed, which can ensure that all the variables in the system are semiglobally uniformly ultimately bounded (SGUUB) in probability and the tracking error gets into prescribed boundary no later than an arbitrarily adjusted setting time. Finally, the proposed algorithm is applied to a RLC circuit and its practicability is verified via simulation results. [ABSTRACT FROM AUTHOR]

This paper investigates the formation control problem for linear multi-agent systems under switching directed topologies. Based on absolute or relative outputs, we propose two distributed observer-based event-triggered control schemes. Both schemes can guarantee the boundedness of formation errors under sufficient conditions. The schemes can also avoid Zeno behaviors by giving an estimation for the lower bound of sampling intervals. Finally, simulations and experiments validate the proposed approaches. [ABSTRACT FROM AUTHOR]

This paper presents a sliding mode dynamic output feedback controller design for Markovian jump systems under a communication network. For the inaccessible states and uncertain parts of Markovian jump systems, a novel integral-type sliding mode output feedback controller combined with system states and dynamic controller states is proposed. An event-triggered mechanism is introduced to reduce network bandwidth and resources requirements. The augmented dynamic system and complete control framework are presented together. The reachability of the novel integral-type sliding mode is proved. Then, based on delay-dependent Lyapunov functions, free-weighting matrices, and a singular value decomposition approach, a less conservative sufficient condition is proposed to ensure exponential stability with a weighted $\mathcal {L}_{2}$ - $\mathcal{ L}_{\infty}$ disturbance performance. Finally, a numerical and a DC-DC switched boost converter circuit simulations that verify the feasibility and effectiveness of the proposed controller are presented. [ABSTRACT FROM AUTHOR]

Energy harvesting techniques provide solutions for powering battery-free circuits or even for charging storage elements such as batteries or super capacitors. In this paper a self-starting switched-capacitor approach based on three-stage charge pump that is appropriate to thermoelectric and photo-voltaic energy harvesting, is carried out in a 28 nm ultra-thin buried oxide (UTBB) fully-depleted silicon-on-insulator (FD-SOI) CMOS technology. By taking advantage of the FD-SOI substrate characteristics, the forward-body-biasing (FBB) technique is applied in order to improve switch conductances. In addition, a sizing exploration of standard N-type and flipped-well P-type devices operating as switches is advanced, in order to provide optimum balance between their conductances. Extensive simulation results validate the proper operation of the charge pump at a minimum input voltage of 150 mV, and show a maximum efficiency peak of 63.3% at an input voltage of 350 mV and load a current of 500 nA. [ABSTRACT FROM AUTHOR]

The reduction of the nominal supply voltage of CMOS technologies with scaling comes with the decrease of the maximum tolerable voltage of the devices. This poses challenges in implementing circuit blocks that are compliant with standardized communication protocols or deal with off-chip signals in voltage domains larger than the nominal supply (e.g., 1.8 V, 3.3 V, 5 V). Design techniques such as cascoding, voltage shifting and adaptive biasing are effective at removing the need for customized voltage resistant input/output (I/O) devices since they prevent intolerable voltage drops. However, at the input of multiple-channel blocks, the design of switches of multiplexers results critical as the input and the output nodes can assume values beyond the signal range, causing harmful biasing configurations. This paper presents the architecture of a switch for input channel multiplexers able to handle signals up to twice the nominal supply voltage of the employed devices. Its effectiveness has been proved by implementing a 1.6V switch with the core MOS transistors of the 28nm CMOS technology with 0.96V nominal supply voltage. The comparison with a benchmark switch based on 1.8V I/O devices showed that both a larger area (slightly more than twice) and static current consumption ($40\mu \text{A}$) are required. [ABSTRACT FROM AUTHOR]

This paper proposes a novel T-type multilevel inverter (MLI) based on the switched-capacitor technique. The proposed inverter not only achieves that the maximum voltage stress of the switches is less than the input voltage but also has a voltage boost capability, which makes it suitable in high voltage applications. It is worth mentioning that the proposed inverter features two topology extension schemes which help it achieve a higher output level and voltage gain. With the merit of low voltage stress and reduced power devices, a seven-level inverter can be achieved using only two capacitors. Moreover, capacitor voltage self-balancing capability can simplify the complexity of the circuit and control. The topology, operating principle, modulation strategy and analysis of the capacitor of the inverter are presented. The superiorities of the proposed inverter are investigated by comparing with recently proposed hybrid MLIs and switched-capacitor MLIs. Finally, a seven-level prototype is constructed to validate the correctness of the theoretical analysis and the feasibility and effectiveness of the proposed inverter. [ABSTRACT FROM AUTHOR]

This paper presents a low-profile and autonomous piezoelectric energy harvesting system consisting of an extraction rectifier and a maximum power point tracking (MPPT) circuit for powering portable electronics. Synchronized switch harvesting on capacitor-inductor (SSHCI) technique with its unique two-step voltage flipping process is utilized to downsize the ponderous external inductor and extend application areas of such harvesting systems. SSHCI implementation with small flipping inductor-capacitor combination enhances voltage flipping efficiency and accordingly attains power extraction improvements over conventional synchronized switch harvesting on inductor (SSHI) circuits utilizing bulky external components. A novel MPPT system provides robustness of operation against changing load and excitation conditions. Innovation in MPPT comes from the refresh unit, which continually monitors excitation conditions of piezoelectric harvester to detect any change in optimum storage voltage. Compared with conventional circuits, optimal flipping detection inspired from active diode structures eliminates the need for external adjustment, delivering autonomy to SSHCI. Inductor sharing between SSHCI and MPPT reduces the number of external components. The circuit is fabricated in 180 nm CMOS technology with 1.23 mm2 active area, and is tested with custom MEMS piezoelectric harvester at its resonance frequency of 415 Hz. It is capable of extracting 5.44x more power compared to ideal FBR, while using $100~\mu $ H inductor. Due to reduction of losses through low power design techniques, measured power conversion efficiency of 83% is achieved at 3.2 V piezoelectric open circuit voltage amplitude. Boosting of power generation capacity in a low profile is a significant contribution of the design. [ABSTRACT FROM AUTHOR]

This paper presents fully integrated switched-capacitor boost-buck power converters with conversion ratios 5, 7, and 1/5. Such converters operate over a voltage range extended beyond the device ratings due to a low-voltage-stress configuration, accumulation-mode NMOS capacitors, and a circuit technique for switch bootstrapping. After modeling the simple and the symmetrical ladder converters, we determined methods for assessing the device working voltages and for optimizing the sizes of capacitors and switches. The key performance parameters were compared and the losses due to non-linear parasitic capacitances were calculated. The characterization of the prototypes in a 1.8–3.3-V, 0.18- $\mu \text{m}$ CMOS process demonstrated a 15 V range, a 5.4 mW/mm2 output power density, and good correlation between measured and predicted results. [ABSTRACT FROM AUTHOR]

This paper investigates the adaptive fuzzy output feedback event-triggered control problem for a class of switched nonlinear systems with sensor faults. Due to that the unknown nonlinearities of the systems are more general and the sensor undergoes faults, the considered problem is difficult to be addressed by existing schemes. Therefore, fuzzy logic systems are employed to approximate unknown nonlinear terms and a fault compensation coefficient is introduced to compensate for the effect of sensor failures. Then, a state observer is established for estimating unmeasured states. By choosing a suitable common Lyapunov function, an adaptive fuzzy output feedback fault-tolerant event-triggered controller is derived. It is proven that the proposed scheme can guarantee that the system output tracks the desired trajectory effectively, all states of the resulting closed-loop system are semi-globally uniformly ultimately bounded, and the Zeno phenomenon is excluded. Finally, two simulation examples, which include a switched RLC circuit system and a numerical example, are presented to show the the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, we propose a new scheme to directly power a 4.9–5.6GHz LC oscillator from a recursive switched-capacitor DC-DC converter. A finite-state machine is integrated to automatically adjust the conversion ratio and switching frequency of the converter such that its DC output voltage is within ±5% of the desired 1V across input voltage range 1.3–2.2V and < 2mA load current conditions. A gate-driver circuit is embedded in each switch of the converter to guarantee constant on-resistance across PVT variations without sacrificing device reliability. Furthermore, a spur reduction block (SRB) is embedded in the oscillator to suppress the ripple induced spurs by stabilizing its tail current. Both the converter and the oscillator are implemented in 40-nm CMOS technology. The measured peak power efficiency of the converter is 87%, while its spot noise is < 1.5nV/ $\sqrt {\mathrm{ Hz}}$ , which does not degrade the phase noise of the oscillator. The SRB suppresses the spur to < −65dBc under the 30mVpp ripple of the converter. [ABSTRACT FROM AUTHOR]

This paper presents a low-power and area efficient 10-bit SAR ADC with higher side-reset-and-set (HSRS) switching scheme and hybrid capacitive-MOS (CAP-MOS) DAC. The HSRS switching scheme consumes zero switching energy for the two most-significant bits and skips unnecessary switching without using any auxiliary circuit. It is further verified in this paper that the HSRS switching scheme shows lower nonlinearity compared with the conventional CDAC structure with the same unit capacitor size and matching condition. This additional advantage permits using DAC topologies with lower total capacitance under given linearity requirement. A hybrid CAP-MOS DAC is adopted to reduce the total capacitance of the DAC, which consumes lower static current and chip area than the conventional hybrid capacitive-resistive DAC under the same settling requirement. The prototype 10-bit SAR ADC is implemented in a 0.18- $\mu \text{m}$ CMOS technology, showing an SNDR/SFDR of 56.43 dB/71 dB at 90-kHz input, under a 0.6-V power supply, while consuming $1.01~\mu \text{W}$ at 200 kS/s for a figure of merit of 9.32 fJ/conv.-step. The ADC occupies only a small active area of 0.0675 mm2. [ABSTRACT FROM AUTHOR]

Slewing in switched capacitor (SC) circuits reduces the available time for linear settling, and hence increases the nonlinear settling error. This transient demand in current can be supplied by making the bias currents larger in the operational transconductance amplifier (OTA). However, this increases the static power consumption significantly. In this paper a slewing mitigation technique is presented where just the right amount of charge is provided at the switching instant to the SC circuit so that OTA does not need to provide high peak current. This may eliminate slewing altogether, and allows using OTAs with less static current for the same settling accuracy. The operation of the proposed technique is illustrated by incorporating it in a second-order delta-sigma modulator (DSM). The modulator was designed and simulated in a 65nm CMOS process. Post-layout extracted simulations with optimized design show more than 12 dB improvement in signal to noise and distortion ratio (SNDR) for the same static power. Alternatively, compared to a DSM without such technique, the same performance can be achieved with 30% less power. [ABSTRACT FROM AUTHOR]

This paper is concerned with the $H_\infty $ control problem for switched systems under the event-triggered sampling, the quantization control and the state-dependent switching. The dynamic event-triggered strategy and the quantization control are utilized to adjust the signal transmission and relieve the transmission load. Different from the existing dynamic event-triggered strategies, the triggering condition only needs to be monitored at discrete time. Moreover, the state-dependent switching law is designed by using only the discrete state information. Under the event-triggered sampling, the quantization control and the state-dependent switching, sufficient conditions are proposed to guarantee the $H_\infty $ performance. A switched RLC system is utilized to verify the results in the simulation. [ABSTRACT FROM AUTHOR]

This paper presents a 12-bit successive approximation register (SAR) analog-to-digital converter (ADC) that uses a digital-to-analog converter (DAC) configurable window switching technique. By reusing the capacitors in the DAC, the proposed window switching scheme yields window boundaries to determine whether the input is located within the window, and thus avoid unnecessary capacitor switching. The proposed window SAR ADC improves the conversion efficiency and ADC linearity. A qualitative analysis of prior window switching schemes is presented to elaborate for various applications. A low-input capacitance of 1 pF was adopted to relax the input and reference buffers. A prototype ADC was implemented in 180-nm CMOS occupying an active area of 0.1 mm2. At 20 MS/s, it consumes a total power of 1.22 mW from a 1.5-V supply. The measured peak signal-to-noise and distortion ratio and spurious-free dynamic range were 61.7 and 79 dB, respectively. At the Nyquist rate, the measured effective number of bits (ENOB) was 9.53, equivalent to a figure-of-merit (FOM) of 83 fJ/conversion-step. In low-power mode (100 kS/s), it consumed a total power of $1.5~\mu \text{W}$ from a 0.7-V supply. At the Nyquist rate, the measured ENOB was 9.82, equivalent to a FOM of 16.6 fJ/conversion step. [ABSTRACT FROM AUTHOR]

This paper presents a millimeter-wave wide tuning range voltage-controlled oscillator (VCO) incorporating two switchable decoupled VCO cores. When the first core is switched on producing the low frequency band (LFB) signal and the second core is off, the inductors of the second core are reused to create additional buffers that pass the LFB signal to the output buffers. The generated high frequency band (HFB) signals by the second core when turned on, are directly fed to the output buffers. Producing the outputs of both VCO cores across same terminals without utilizing active/passive combiners and coupled inductors will enhance the phase noise performance of the VCO, increase its output power, and reduce the chip size. Fabricated in a 65-nm CMOS process, the VCO achieves a measured wide tuning range of 26.2% from 54.1 to 70.4 GHz while consuming 7.4–11.2-mA current from 1-V power supply. The peak measured phase noise at 10-MHz offset is −116.3 dBc/Hz and the corresponding FOMT and FOM varies from −180.96 to −191.86 dB and −172.6 to −183.5 dB, respectively. The VCO core area occupies only $0.1 \,\, \times 0.395\,\,\mu \text{m}^{{2}}$. [ABSTRACT FROM AUTHOR]

This paper proposes a new switching sequence with the asymmetric placement of weighting elements for a unary digital-to-analog converter (DAC). The proposed sequence is based on a so-called knight’s tour according to the modified Warnsdorf’s rule. To estimate the efficiency of the proposed switching sequence, a 10-bit resistive DAC has been designed and fabricated in the UMC 180-nm technology. Experimental results show that in comparison with an array of weighting elements without compensation of the systematic error, the proposed switching sequence reduces the maximal integral (INL) and the mean INL by 20% on the average in the temperature range from −40 °C to 85 °C. Besides that, the maximal INL does not depend on the temperature, while the mean INL decreases with temperature increase. [ABSTRACT FROM AUTHOR]

This paper presents a low-power and area efficient 10-bit successive approximation register (SAR) analog-to-digital (ADC) with a hybrid capacitive-MOS consisting of a 7-bit MSB capacitive DAC (CDAC) and a 3-bit LSB MOS DAC (MDAC), which consumes less power and much smaller chip area than a pure CDAC. Instead of using a string of eight MOS transistors to control one unit capacitor, the 3-bit LSB MDAC is realized by a MOS string with four native MOS transistors to control two unit capacitors, which allows higher voltage drop and more reliable operation for each unit MOS. The overall energy consumption of the proposed CAP-MOS DAC is reduced by 56.2% compared to a Vcm-based 10-bit pure CDAC with the same unit capacitance. Under the sampling rate of 200 kS/s, the prototype 10-bit SAR ADC implemented in a 0.18- ${\mu }\text{m}$ CMOS technology achieves a signal-to-noise-and-distortion ratio / spurious-free dynamic range of 56.91 /68.56 dB at 99-kHz input under a 0.6-V power-supply, while consumes $1.76~{\mu }\text{W}$ at 200 kS/s for a figure of merit of 15.38 fJ/step. The peak DNL and INL are +0.27/−0.21 LSB and +0.43/−0.45 LSB, respectively. The ADC occupies a small active area of 0.097 mm2. [ABSTRACT FROM AUTHOR]

This paper presents a low-energy 64-Kb eight-transistor (8T) one-read/one-write dual-port image memory with a 28-nm fully depleted SOI (FD-SOI) process technology. Our proposed SRAM adopts a selective sourceline drive (SSD) scheme and a consecutive data write technique for improving active energy efficiency at low voltage. The novel SSD scheme controls sourceline voltage and eliminates leakage energy at unselected columns in read operations. We fabricated a 64-Kb 8T dual-port SRAM in the 28-nm FD-SOI process technology. The 8T SRAM cell size is $0.291 \times 1.457\,\,\mu \text{m}^{2}$. The test chip exhibits 0.48-V operation at an access time of 135 ns. The energy minimum point is at a supply voltage of 0.56 V and an access time of 35 ns, where 265.0 fJ/cycle in write operations and 389.6 fJ/cycle in read operations are achieved. These factors are, respectively, 30% and 26% smaller than those of the 8T dual-port SRAM with the conventional scheme. [ABSTRACT FROM AUTHOR]

The high-speed successive-approximation-register (SAR) analog-to-digital converters (ADCs) rely on the switched capacitive digital-to-analog converter (CDAC) to perform the fast transition, which causes voltage ripples at the output of the reference circuits. Such ripples lead to the reference error that eventually prolongs the time for DAC settling. To minimize such error with a short available time, it either demands a power-hungry reference buffer or large die area for the decoupling. In this paper, we offer a comprehensive analysis of the reference errors in SAR ADCs with a practical reference network circuit (RNC) in consideration. A circuit model is developed in order to quantify the error amplitude for the critical DAC settling condition. Based on the proposed model, the settling behavior of the DAC with reference buffer can be precisely characterized, leading to a better understanding about the design tradeoff of the RNC. Finally, the developed model is verified by both circuit level simulations and measurement results. [ABSTRACT FROM AUTHOR]

This paper presents the design of integrated boost and buck switched-capacitor power converters with high efficiency and fast start-up time. An analysis method is determined to evaluate the key performance parameters of integrated power converters, and techniques are proposed to improve the energy conversion efficiency and the dynamic response. Boost and buck structures are modeled and compared in static and transient conditions, including the losses due to parasitic elements. A switch bootstrapping technique prevents short-circuit losses, improves driving capability and start-up time, and enhances the overall efficiency. Moreover, the application of a charge-reuse technique reduces the dynamic power losses of the integrated structures. Prototypes of the integrated power converters were fabricated in a 180-nm CMOS process. Measurement results based on the proposed techniques are presented, demonstrating the improvements in steady-state and transient characteristics with a good correlation between measured and predicted results. [ABSTRACT FROM AUTHOR]

This paper presents an area- and power-efficient dual-output switched capacitor (DOSC) dc–dc buck converter for wearable biomedical devices. The DOSC converter has an input voltage range between 1.05 and 1.4 V and generates two simultaneous regulated output voltages of 1 and 0.55 V. The DOSC consists of two main blocks: a switched capacitor regulator and an adaptive time multiplexing (ATM) controller. The switched capacitor regulator generates a single regulated voltage using pulse frequency modulation based on a predetermined reference voltage. In addition, the ATM controller generates two simultaneous output voltages and eliminates the reverse current using pulse width modulation during the switching between the output voltages. Addressing the reverse current problem is important to reduce the output voltage droop and improve the performance. The proposed converter supports load currents of 10– $350~\mu \text{A}$ and 1– $10~\mu \text{A}$ at load voltages of 1 and 0.55 V, respectively. The DOSC circuit is fabricated in 65-nm CMOS, and it occupies an active area of 0.27 mm2. Measured results show that a peak efficiency of 78% is achieved at a load power of $300~\mu \text{W}$. [ABSTRACT FROM AUTHOR]

This paper presents a systematic method to analyze $N$ -path mixers and filters consisting of periodically switched $RC$ -networks of arbitrary order. It is assumed that each capacitor periodically exchanges charge with the rest of the network during the on-phase of the switching clock, then samples its charge, and holds it perfectly until the next on-phase. This assumption allows for using the adjoint network for simplified analysis of the harmonic transfer functions that describe the signal transfer and folding. Moreover, harmonic transfer cancellations due to the $N$ -path implementation with $N$ equal capacitors switched by $N$ non-overlapping clocks are systematically analyzed. The method is applied to a recently published $N$ -path filter-mixer combination and verified by simulations. [ABSTRACT FROM AUTHOR]

This paper proposed a high efficiency boost converter targeting thermoelectric generator energy harvesting. The proposed converter adopts the critical conduction mode rather than the discontinuous mode to reduce the conduction loss, which can improve the peak efficiency at high input power. To reduce the minimum input voltage, an adaptive on-resistance switch, which can automatically change the high side and low side on-resistance according to the input voltage, is used. To maximize the output power, a maximum power point tracking circuit is designed to track the internal source resistance. Radio frequency (RF) kick-up and low voltage startup are used to improve the cold start voltage. The proposed converter is implemented in a 0.18- $\mu \text{m}$ standard CMOS process, which occupies a chip area of about 0.48 mm2. Measurement results show that the peak efficiency of the converter can be up to 90.8% and 60% at 180 and 20 mV of the open-circuit voltage, respectively. Owing to the cold startup circuit, the proposed converter can start successfully with 260-mV open-circuit voltage or −16-dBm RF input. Moreover, the open-circuit voltage can be further lowered to 12 mV with 1.5- $\mu \text{W}$ output power after startup. [ABSTRACT FROM AUTHOR]

The cooperative output regulation problem for singular multi-agent systems subject to static networks was studied recently under the assumption that each follower system satisfies the standard assumption. In this paper, we further study the same problem for singular multi-agent systems subject to jointly connected switching networks. First, by introducing a static output feedback control, we remove the unnecessary standard assumption on the singular system in the existing result. Then, we derive a reduced-order normal multi-agent system and obtain a distributed output measurement feedback control law based on the existing result on the normal multi-agent system. Finally, we show that the composition of the static output feedback control law and the distributed output measurement feedback control law solves the cooperative output regulation problem for the original singular multi-agent system. Our result enlarges the class of systems whose cooperative output regulation problem is solvable. [ABSTRACT FROM AUTHOR]

An efficient self-powered synchronous electric charge extraction CMOS interface circuit dedicated to piezoelectric harvesters is proposed in this paper. Self-powered peak detection (PKD) and switch circuits are used to reduce quiescent current so that the backup or pre-charged power can be saved. A new low phase lag (LPL) PKD circuit is designed to improve the synchronous extraction efficiency, which only requires one detection capacitor to perform positive and negative PKD. The circuit can be set at general mode (G-mode) or LPL mode (LPL-mode). Under LPL-mode, the phase lag can be reduced typically by 50%, the synchronous extraction efficiency can obtained up to 94%, while the output power can reach 659~\mu \textW when the piezoelectric transducer original open-circuit voltage V\mathrm{ oc,org}=5 V, which is 3.56 times of that of full-bridge rectifier standard energy harvesting circuit at the maximum power point. The minimum harvesting startup voltage is 1.7 V and is independent of the energy storage capacitor voltage V\mathrm{ DC} . The harvesting efficiency can still reach 71.3% at V\mathrm{ oc,org}=5 V. The size of the active area is 0.5 mm2 in a 0.18- \mu \textm CMOS technology. Circuit may be invoked as a functional block for energy autonomous wireless sensor network node of the Internet of Things. [ABSTRACT FROM PUBLISHER]

This paper presents a piezoelectric-based power management solution for battery-free wireless remote switches (BWSs). The proposed BWS IC, including a piezoelectric (PE) energy harvester and a buck converter, can collect the energy generated by a single PE-button press, and then supply that energy to a wireless transmitter to send a message. By combining a rectifier using the synchronized switch harvesting on inductor technique and a 6:1 series–parallel switched-capacitor converter, the proposed PE energy harvester can maximize the collected amount of energy, while supplying it at a low output voltage. In addition, by employing a switching-based start-up scheme and a variable ON-time pulse-frequency modulation scheme, the proposed buck converter can reduce the loss associated with charging the output capacitor during start-up, and then deliver the largest possible energy to the load, while maintaining low voltage ripples and high-power efficiency. A prototype BWS IC fabricated with high-voltage 250-nm CMOS technology was shown to be capable of harvesting a total energy of 246~\mu \textJ from a single button-pressing of a 300-mm2 lead magnesium niobate-lead titanate PE disc. More than 200~\mu \textJ was delivered to the load, sufficient to transmit a 4-B-long message via a 2.4-GHz wireless USB channel over a 10-m distance. [ABSTRACT FROM AUTHOR]

This paper proposes an ultralow power, high precision sub bandgap voltage reference (sub-BGR) for low-voltage self-powered devices. A novel ultralow power curvature compensation circuit is proposed to improve the temperature coefficient over a wide temperature range. A switch capacitor voltage divider with improved leakage current reduction switches is used to obtain a high accuracy and a low power. To minimize the clock feedthrough and charge injection in the switches, a clock scaling down circuit is proposed, that effectively improves the line sensitivity (LS) of the sub-BGR. The proposed sub-BGR is implemented in a 0.18- \mu \textm standard CMOS process with a total area of 0.061 mm2. After measuring 30 chips, the average power consumption is 83 nW at 0.55 V of supply at 27 °C. In the supply voltage range of 0.55 to 1 V, the LS is 0.059%/V, and the error is ±0.75% ( $3\sigma $ ) after trimming. [ABSTRACT FROM PUBLISHER]

This paper presents a low-power, area-efficient 11-b single-ended successive-approximation-register (SAR) analog-to-digital converter (ADC) targeted for biomedical applications. The design features an energy-efficient switching technique with an error cancelling capacitor network. The input range is twice the reference voltage. The ADC’s loading of the previous stage is reduced by using a single-ended structure, and by eliminating the largest capacitor in the array. The common mode voltage of the input signal can be used as reference voltage. All building blocks were designed in subthreshold for power efficiency, with an asynchronous self-controlled SAR logic. The ADC was fabricated in 0.18 – \mu \textm CMOS 2P4M process. The measured peak SNDR was 60.5 dB, the SFDR was 72 dB, the DNL +0.6/−0.37 LSB, and the INL +0.94/−0.89 LSB. The total power consumption was 250 nW from 0.75-V supply voltage. [ABSTRACT FROM PUBLISHER]

Nonlinear circuits may be synchronized with interconnections that evolve in time incorporating mechanisms of adaptation found in many biological systems. Such dynamics in the links is efficiently implemented in electronic devices by using memristors. However, the approach requires a massive amount of interconnections (of the order of N^2 , where $N$ is the number of nonlinear circuits to be synchronized). This issue is solved in this paper by adopting a memristor crossbar architecture for adaptive synchronization. The functionality of the structure is demonstrated, with respect to different switching characteristics, via a simulation-based evaluation using a behavioral threshold-type model of voltage-controlled bipolar memristor. In addition, we show that the architecture is robust to device variability and faults: quite surprisingly, when faults are localized, the performance of the approach may also improve as adaptation becomes more significant. [ABSTRACT FROM PUBLISHER]

This paper presents a nonlinear state-space model (SSM) for a low power 28-nm complementary metal–oxide–semiconductor switched-capacitor digital-to-analog converter. The proposed model utilizes current–voltage (I-V) input and output relationships for passive devices, which are described by a set of first-order differential equations. The proposed model significantly increases accuracy when compared with the state-of-the-art models. The SSM simulation results have been verified using SpectreRF transistor-level simulations and validated by on-chip measurements. [ABSTRACT FROM AUTHOR]

Nowadays, more and more RF systems include switchable matching networks to decrease the impact of the environment-dependent antenna impedance on the RF front end performance. This paper reviews the theoretical lower limit on the required number of matching states to match VSWR ranges and then presents an analysis of hardware implementations to actually implement a suitable switchable matching network. A number of matching network topologies are analyzed: PI networks, loaded transmission lines, branch line coupler based circuits, single circulators and cascaded circulators. In our investigation only narrow-band applications are targeted. For the various circuit implementations the required number of matching states for each hardware implementation is compared to the theoretical minimum number of states required for the same matching in order to benchmark their hardware implementation overhead. It appears that a matching network using cascaded circulators is the closest to the theoretical optimum for networks with a relatively low number of states: this type of matching network was implemented and analyzed in more detail. [ABSTRACT FROM AUTHOR]

This paper presents the design and implementation of a 10-bit ultra-low voltage energy-efficient successive approximation register (SAR) analog-to-digital converter (ADC). The proposed first 2-bit guess (F2G) scheme reduces the DAC switching energy by 90% and improves the DNL and INL by \sqrt 3 /2 in theory compared with the conventional approach. By employing majority-vote comparison at the conversions of LSBs, the noise requirement of comparator can be relaxed by half. With the segmented and bundled routing, the parasitic capacitors of bottom-plates of DAC array are reduced to improve power efficiency and speed. Implemented in 90-nm CMOS technology, the test chip occupied a core area of 0.03 mm2. The prototype consumes 67.3 nW at 150 kS/s from a single 0.3 V supply voltage and achieves an ENOB of 8.85 bits and an SFDR of 70.7 dB at Nyquist input, respectively. The resultant Walden’s FoM and Schreier’s FoM are 0.97 fJ/conv.-step and 175.5 dB, respectively. [ABSTRACT FROM AUTHOR]

This paper presents a new method for detecting and reversing the polarity of a low-voltage thermoelectric generator (TEG) in inductor-based converters. The proposed technique makes use of the inductor response to a voltage change due to the flip in the TEG polarity. The inductor voltage provides two distinguishable states which correspond to the normal and the reversed TEG polarity. A switch matrix circuit is then used to correct the polarity by physically reversing the TEG connection. The detection circuit along with the switch matrix provide a positive input voltage from the TEG to the inductor-based converter. The proposed technique is an efficient polarity detection with all-digital implementation, fully integrated, small area and power overhead. The prototype chip is fabricated in 65-nm CMOS and occupies an area of 0.09 mm2. Measurement results confirm a maximum efficiency of 70% at 50 mV TEG voltage and 40~\mu \text A output current. The proposed technique is part of an autonomous thermal energy harvesting system that detects and corrects the TEG polarity. [ABSTRACT FROM AUTHOR]

This paper presents a piezoelectric energy harvesting circuit, which integrates a Synchronized Switch Harvesting on Inductor (SSHI) circuit and an active rectifier. The major design challenge of the SSHI method is flipping the capacitor voltage at optimal times. The proposed SSHI circuit inserts an active diode on each resonant loop, which ensures flipping of the capacitor voltage at optimal times and eliminates the need to tune the switching time. The diodes of the SSHI circuit are also used as a rectifier to further simplify the controller. The key advantage of the proposed circuit is a simple controller, which leads to low power dissipation of the proposed circuit to result in high efficiency. The proposed circuit is self-powered and capable of starting even when the battery is completely drained. The circuit was fabricated in BiCMOS 0.25~\mu \text m technology with a die size of 0.98 \times 0.76 mm2. Measured results indicate that the proposed circuit increases the amount of power harvested from a piezoelectric cantilever by 2.1 times when compared with a full bridge (FB) rectifier and achieves a power conversion efficiency of 85%. The proposed circuit dissipates about 24~\mu \text {W} while the controller alone only 1.5~\mu \text {W}$ . [ABSTRACT FROM AUTHOR]

High step-up conversion is an indispensable feature for the power processing of low voltage renewable sources in grid-connected systems. Motivated by this necessity, this paper presents a study on non-isolated dc-dc converters based on the conventional Boost converter that can provide such feature with high efficiency. By the topological variation and gain cell concepts, it is demonstrated that these converters can be treated as a unique generalized converter, called Boost Converter with Gain Cell (BCGC). The operating principle, the key waveforms and the components stresses of the BGCG are analyzed for the continuous-conduction mode, independently of the employed gain cell. A methodology to create the gain cells is developed from the combination of coupled inductors and voltage multiplier techniques. In order to verify the realized analysis, a 150 W prototype concerning to the proposed generalized converter and able to operate with several different gain cells is developed for the comparison between theoretical and experimental static gain results. [ABSTRACT FROM PUBLISHER]

This paper presents an efficient numerical methodology to obtain the frequency response of switched-capacitor filters based on the circuits' differential equations. This methodology uses a non-hierarchical approach in which the non-ideal effects of the transistors (in the switches and in the amplifier) are taken into consideration, allowing the accurate computation of the frequency response, even in the case of incomplete settling in the SC branches. The accuracy is demonstrated by comparing the results obtained using the proposed methodology with those obtained using transient electrical simulation results for three different SC circuits: a first order SC passive filter, a second order SC lowpass filter, and a second order SC bandpass filter, showing that the results are in good agreement with the more time consuming electrical simulation of the circuits. [ABSTRACT FROM PUBLISHER]

Switching currents of simultaneous switching output (SSO) buffers can cause significant power-supply-induced jitter (PSIJ) and uncertainty in the output voltages. The bit error rate (BER) can be simulated by considering all possible input data patterns with a long data sequence; however, it requires large computational efforts. In this paper, the SSO waveforms are analytically calculated, including the rise time of the input voltage, and the probability density functions (PDFs) of the waveforms are analytically calculated. The PDFs of the SSO step responses are combined with the inter-symbol interference (ISI) PDF extraction. The statistical eye and BER eye diagrams obtained from the proposed method are validated with HSPICE simulations. The effects of the SSO patterns as well as the channel ISI are successfully included in the proposed method. Also, the effects of input rise time and the number of parallel SSO buffers are investigated, and the proposed method is extended for analysis of SSO buffers with the data bus inversion (DBI) coding. The method should be practically useful for design of wideband memory I/O interfaces and low-cost consumer devices by reducing the computational time of the jitter and BER drastically. [ABSTRACT FROM PUBLISHER]

This paper presents a low-voltage and power-efficient 10 bit successive-approximation register (SAR) analog-to-digital converter (ADC). The input-range-adaptive (IRA) switching method is proposed to reduce the average switching power of capacitive digital-to-analog convertor (DAC) by 91% compared with the conventional approach. By utilizing the comparator as a voltage-to-time converter (VTC) with a time-domain quantizer, the implemented early-late (E/L) detection circuit, the input range is detected to eliminate the unnecessary DAC switching power efficiently. A prototype ADC chip is fabricated in 90 nm CMOS technology with an active area of 0.038 mm2. At 0.35-to-0.5 V supply voltage and 0.3-to-2 MS/s sampling rate with a Nyquist input, the ADC achieves a signal-to-noise-plus-distortion ratio (SNDR) of 55.5 dB to 56.3 dB and a corresponding effective number of bits (ENOB) of 8.92 bit to 9.06 bit respectively with a power consumption of 0.3~\mu \text W to 2.5~\mu \text W and a resulting figure of merit (FoM) from 1.94 fJ/conversion-step to 2.32 fJ/conversion-step. [ABSTRACT FROM PUBLISHER]

Design details and analysis of the properties of a hysteresis switching controller for the Ćuk converter are provided in this paper. The design is based on a switching control law which minimizes a common Lyapunov function derivative for the converter's continuous modes of operation. These continuous modes of operation are both marginally stable which causes some particularities in the design procedure. The design also meets the specifications in terms of the converter's duty ratio and the frequency limitations. The proposed hysteresis controller performance is analyzed with respect to the operating modes of the converter and illustrated with a number of representative and relevant simulations. [ABSTRACT FROM PUBLISHER]

A 12-bit 10 MS/s SAR ADC with enhanced linearity and energy efficiency is presented in this paper. A novel switching scheme (COSS) is proposed to reduce the power consumption and the matching requirement for capacitors in SAR ADCs. The switching energy (including switching energy and reset energy), total capacitance and static performance (INL & DNL) of the proposed scheme are reduced by 98.08%, 75%, and 75%, respectively, compared with the conventional architecture. Based on analysis of the non-linear errors caused by comparator input parasitic capacitance, an improved comparator with push-pull pre-amplifier and output offset storage (OOS) strategy is proposed to diminish non-linearity in the input parasitic capacitance. The offset cancellation signal for the comparator can be generated by asynchronous timing automatically, without any extra clock. Additionally, an SFDR enhancement bootstrap switch is proposed to eliminate the distortion induced by parasitic capacitance and threshold voltage that results in insufficient precision for medium-speed 12-bit ADCs. The proposed ADC was fabricated in a 0.18 \mu\textm 1P6M CMOS process, and the measured results show that the ADC achieves an SNDR of 66.9 dB and an SFDR of 75.8 dB with a 10 MS/s sampling rate and consumes 0.82 mW, resulting in a figure of merit (FOM) of 44.2 fJ/conversion-step. The peak DNL error is +0.36/−0.33 LSB, and the peak INL error is +0.55 LSB/−0.6 LSB. The ADC core occupies an active area of only 630\ \mu\textm\! \times\! 570\ \mu\textm^2. [ABSTRACT FROM PUBLISHER]

This paper presents novel designs of static dual-edge-triggered (DET) flip-flops that exhibit unique circuit behavior owing to the use of C-elements. Five novel DET flip-flops are presented including two high-performance designs and designs that improve upon common Latch-MUX DET flip-flops so that none of their internal circuit nodes follow changes in the input signal. A common characteristic of the presented flip-flops is their low energy dissipation due to glitches at the input. Novel DET flip-flops are compared to existing DET flip-flops using simulation in a high performance 28 nm CMOS technology and are shown to have superior characteristics such as power and power-delay product (PDP) for a range of switching activities. Extensive Monte Carlo and voltage scaling simulations are performed to show that the presented designs are robust under PVT variations. [ABSTRACT FROM PUBLISHER]

A frequently occurring subcircuit consists of a loop of a resistor (R), a field-effect transistor (FET), and a capacitor (C). The FET acts as a switch, controlled at its gate terminal by a clock voltage. There may be many such identical circuits connected in parallel, each driven by a different phase of the clock. This subcircuit may be acting as a sample-and-hold (S/H), as a passive mixer (P-M), or as a bandpass filter or bandpass impedance. In this work, we will present a useful analysis that leads to a simple signal flow graph (SFG), which captures the FET-R-C circuit's action completely across a wide range of design parameters. The SFG dissects the circuit into three filtering functions and ideal sampling. This greatly simplifies analysis of frequency response, noise, input impedance, and conversion gain, and leads to guidelines for optimum design. The analysis is extended to multi-path realizations common in RF applications. Part I of this paper focuses on the analyses of a single-path FET-R-C circuit's signal transfer characteristics. Part II extends these analyses to multi-path FET-R-C circuit configurations, which is followed by the noise and driving-point impedance analyses. [ABSTRACT FROM AUTHOR]

Designing a SPICE model is a critical step toward understanding the behavior of the resistive random access memory (RRAM) devices when integrated in memory design for the future generation storage devices. In this paper, a SPICE model is developed for the \textrmTa2\textrm{O}5/\textrm{TaO}x bi-layered RRAM. The proposed model emphasizes the impact of the change in the switching layer thickness on the device behavior at low resistance state (LRS), high resistance state (HRS), and the transitional period. The validity of the proposed model is verified through using three different sets of experimental data from \textrmPt/Ta2\textrm{O}5/\textrm{TaO}x/\textrm{Pt} RRAM with switching layer thickness smaller than 5 nm. The SPICE model reproduced all the major features from the experimental results for the SET and RESET processes and also the asymmetric and the symmetric characteristics in HRS and LRS, respectively. The proposed SPICE model matches the measured experimental results with an average error of < 11% and a maximum error of < 70%. It also showed stable behavior for its HRS and LRS regions under different types of input signals. The model is parameterized in order to fit into \textrmTa2\textrm{O}5/\textrm{TaO}x RRAM devices with switching layer thickness smaller than 5 nm, thus, facilitating the model usage. The model can be included in the SPICE-compatible circuit simulation and is suitable for the exploration of the \textrmTa2\textrm{O}5/\textrm{TaO}x bi-layered RRAM device performance at circuit level. [ABSTRACT FROM AUTHOR]

This paper presents a design procedure of high-frequency loosely inductive coupled wireless power transfer (LIC-WPT) system based on class-E^2 dc-dc converter, taking into account the power loss reduction of inverter, coupling part, and rectifier simultaneously. Analytical expressions including the dc-to-dc efficiency of the WPT system are derived and the efficiency deterioration mechanism is explained by the circuit model. Through the analytical expressions, the design procedure for satisfying both the class-E switching conditions and power loss reductions at the coupling part is proposed from the circuit-theory viewpoint. The class-E^2 WPT system designed by the proposed design procedure achieves high dc-to-dc efficiency at low coupling coefficient, in particular, compared with those designed by the previous design strategies. The validity and effectiveness of the proposed design procedure were confirmed by PSpice simulations and circuit experiments. [ABSTRACT FROM PUBLISHER]

In this paper the power losses of efficient capacitive converters with multitude transfer ratio values are discussed. The loss mechanism circuits, based on general transposed series parallel (GTSP) topology, is studied and the losses are calculated, which in turn enables the “bottlenecks” to be identified and overcome. The calculations show that for a given number of switching cells the power losses of such converters are mainly dependent on the voltage conversion ratio, the topology function, the resistances of the switches in on and off states, the ESR of the capacitors, the switching frequency, the voltage drop, and the load. The theory explains the fact that was observed in experiments, that for low voltage conversion ratio values, efficiency decrease was measured. It is shown that for these low voltage ratio values the mechanism associated to the off resistance of the switches is more dominant and reduces the efficiency. This power loss estimation can be used as a powerful tool for the performance optimization of capacitive converters. The theoretical results are verified experimentally on a 10-cell GTSP converter prototype. The experimental results show good agreement with the proposed theory. [ABSTRACT FROM PUBLISHER]

A maximum-power-point-tracking DC-DC boost converter to harvest energy from sub-\muW power sources is presented. For available input-power levels below 1 \muW, voltage boosting is achieved by operating all circuits in the sub-threshold region, and by switching the DC-DC converter at tens of Hz, thereby reducing switching losses. The paper further explores the possibility of energizing the DC-DC inductor for an optimum duration, such that switching and resistive losses are minimized. The sub-\muW energy harvesting circuit uses an area of 0.2 mm^2 on a standard 180 nm CMOS process, and utilizes an auxiliary voltage source for start-up. The designed and fabricated system is more than 50% efficient when the available power is greater than 2 \muW. The circuit can harvest energy whenever the available power is more than 0.3 \muW. Efficiency at 0.3 \muW is 25%, at 0.5 \muW is 37% and at 1 \muW is 48%. The complete IC consumes 50 nA for internal operations and the input voltage can be as low as 70 mV. [ABSTRACT FROM PUBLISHER]

This paper presents a 10-bit ultra-low power successive approximation register (SAR) analog-to-digital converter (ADC) for implantable medical devices. To achieve the nanowatt range power consumption, a novel switching scheme is proposed, which can accomplish the first three comparisons without consuming any energy and thus improve the energy efficiency significantly. In addition, to boost the offset performance of the comparator working under low supply voltage, a detailed theoretical analysis of comparator offset voltages is made. Based on the analysis, the comparator is optimized by only adjusting transistor sizes without any particular offset cancellation. As a result, when the common-mode input voltage varies from 300 mV to 450 mV at a 0.6 V supply, the 3\times\sigma offset voltage is optimized to be about 6 mV with a fluctuation of only 0.15 mV, as revealed by Monte Carlo simulations. A prototype of the proposed ADC was fabricated in 0.18 \mum 1P6M CMOS technology, which occupies an active area of only 380\times 430\ \mum^2. At a 0.6-V supply and 20 kS/s sampling rate, the ADC achieves an SNDR of 58.3 dB and a power consumption of 38 nW, resulting in a figure of merit (FOM) of 2.8 fJ/conversion-step. [ABSTRACT FROM AUTHOR]

This paper studies asymptotic output synchronization for a class of dynamical networks with identical nonlinear nodes and switching topology. The node dynamics are characterized by a quadratic form of incremental-dissipativity. The output synchronization problem of the switched network is first converted into the set stability problem for the interconnected nonlinear system with a particular selection of input-output pair, which preserves dissipativity. Then, synchronization under arbitrary switching among self-synchronizing subnetworks and synchronization by design of switching among subnetworks, where none of them is necessarily self-synchronizing, are investigated by using the common Lyapunov function method and the single Lyapunov function method, respectively. Algebraic synchronization criteria for both cases are established, and the obtained results are applied to the investigation of coupled biochemical oscillators and coupled Chua's circuits. [ABSTRACT FROM AUTHOR]

This paper proves a novel sampling theorem with constant amplitude and variable width pulses. The theorem states that any bandlimited baseband signal within \pm0.637 can be represented by a pulsewidth modulation (PWM) waveform with unit amplitude. The number of pulses in the waveform is equal to the number of Nyquist samples and the peak constraint is independent of whether the waveform is two-level or three-level. The proof of the sampling theorem uses a simple iterative technique that is guaranteed to converge to the exact PWM representation whenever it exists. The paper goes on to develop a practical matrix based iterative technique to generate the PWM waveform that is guaranteed to converge exponentially. The peak constraint in the theorem is only a sufficient condition. In fact, many signals with higher peaks, e.g., lower than Nyquist frequency sinusoids, can be accurately represented by a PWM waveform. [ABSTRACT FROM PUBLISHER]

Motivated by different applications in circuits, electromagnetics, and optics, this paper is concerned with the synthesis of a particular type of linear circuit, where the circuit is associated with a control unit. The objective is to design a controller for this control unit such that certain specifications on the parameters of the circuit are satisfied. It is shown that designing a control unit in the form of a switching network is an NP-complete problem that can be formulated as a rank-minimization problem. It is then proven that the underlying design problem can be cast as a semidefinite optimization if a passive network is designed instead of a switching network. Since the implementation of a passive network may need too many components, the design of a decoupled (sparse) passive network is subsequently studied. This paper introduces a tradeoff between design simplicity and implementation complexity for an important class of linear circuits. The superiority of the developed techniques is demonstrated by different simulations. In particular, for the first time in the literature, a wavelength-size passive antenna is designed, which has an excellent beamforming capability and which can concurrently make a null in at least eight directions. [ABSTRACT FROM PUBLISHER]