Search

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

Induction motor drives operated with a low ratio of the switching frequency to the fundamental frequency (i.e., pulse number) are prone to have high magnitudes of low-order torque harmonics. This paper proposes a method to analytically evaluate the harmonic torque spectrum based on the pulsewidth-modulated voltage waveforms for low pulse number operation. The predicted torque harmonic spectra for different pulsewidth-modulated waveforms are validated through simulations and experiments. This paper also reports optimal switching angles to minimize the total rms value of torque harmonics of order 6, 12, 18 $,\dots,$ $6(N-1)$ , considering the number of switching angles per quarter ($N$) to be 4 and 5. Compared to sine triangle pulsewidth modulation and selective harmonic elimination pulsewidth modulation with the same pulse number, the proposed optimal switching angles significantly reduce the total rms value of all harmonic torques of order lower than $6N$. Extensive simulation and experimental results on a 3.7-kW induction motor drive are presented to demonstrate the superior performance of the proposed optimal pulsewidth modulation. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

Digital current controllers have the key impact on the performance of grid-side converters and ac drives. The voltage disturbances are commonly suppressed by enhancing the controller with an inner active resistance feedback. In cases where the switching noise and parasitic oscillations introduce sampling errors, conventional sampling is replaced by the oversampling-based error-free feedback acquisition which derives the average of the measured currents over the past switching period. The time delay introduced into the feedback path creates difficulties in designing the current controller with the active resistance. In this paper, we introduce a novel structure of the current controller, which includes the error-free sampling and the active resistance feedback. Devised structure improves the disturbance rejection by extending the range of permissible values of the active resistance. Controller structure is based on the internal model principles, and it maintains the input step response unaffected. This paper comprises analytical design, the gain setting procedure, computer simulation, and experimental results obtained from an experimental setup with a three-phase inverter, digital controller, and a permanent-magnet synchronous motor. [ABSTRACT FROM PUBLISHER]

A novel hybrid pulse width modulation (PWM) technique is proposed in this paper for two parallel interleaved, two-level, three-phase voltage source inverters (VSIs). The two parallel interleaved VSIs are analyzed as a three-level (3L) inverter. A 3L inverter provides minimum line current ripple when nearest three voltage vectors are applied. In this paper, a novel carrier-based PWM technique is developed that ensures the application of nearest voltage vectors, keeping average circulating current to zero over a switching period. For carrier-based implementation of the proposed PWM, generalized common-mode (CM) offsets are derived in terms of maximum and minimum values of reference signals. Each 3L space-vector sector is divided into seven subsectors. For each subsector, a CM offset is calculated, addition of which to reference signals ensures the minimum line current ripple and zero average circulating current. Simulation and experimental results are provided to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

Two three-level inverters driving an open-end winding induction motor can generate equivalent voltage waveforms as a single five-level inverter-based drive. In addition, it can bring in benefits such as reduced dc-link voltage, less number of devices, and fault-tolerant capability, which is favored in high-power motor drive applications. The main challenge with this type of configuration is the appearance of large zero-sequence current circulating between the two inverters, which generates extra losses in the switching devices and the motor as well as affects the normal operation of the machine. Another challenge is to balance the dc-link neutral point voltage of the two three-level inverters. This paper has proposed a simplified decoupled space-vector pulsewidth-modulation (PWM) strategy to eliminate the averaged zero-sequence voltage in each switching cycle by the placement of redundant vectors of each individual inverter using a time shift. Neutral point voltage balance is further achieved by adjusting the time duration of the redundant vectors. In this paper, it is shown that it is possible to operate this kind of drive configuration with a single dc power supply and achieve averaged zero-sequence voltage elimination and neutral-point voltage balancing at the same time. Experimental results of a 5.5-kW dual three-level inverter drive using the proposed PWM strategy are presented, which validates the control method and drive configuration. [ABSTRACT FROM PUBLISHER]

This paper presents a five-phase dual random space vector pulsewidth modulation (FPDR-SVPWM) strategy with an optimized probability density function (PDF) for a five-phase voltage-source inverter, and its performance and evaluation are also analyzed. Based on the nearest four vectors modulation method, the FPDR-SVPWM strategy, combined with random switching frequency and random zero vector, is investigated to significantly reduce the amplitude of high-order harmonics near the switching frequency and its integer multiples. For the nonsinusoidal power supply, third harmonic injection is introduced in this modulation strategy as well. Considering the effect of random numbers on the performance, an optimized Beta distribution is studied in detail. In order to analyze harmonic dispersion degree qualitatively and quantitatively, the power spectral density and the harmonic spread factor are both employed to assess the performance of the FPDR-SVPWM strategy. A series of results of simulation in MATLAB and experiments based on field programmable gate array demonstrate that the proposed modulation strategy is correct and valid, and it distributes high-order harmonics into a wide range without affecting the fundamental wave and third harmonic. [ABSTRACT FROM AUTHOR]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

Multilevel inverters are now-a-days being applied in electric vehicles (EV). Considering the dynamic operating conditions of an EV propelled by an induction motor, this paper proposes a flexible discontinuous modulation strategy for three-level neutral-point-clamped (NPC) inverter that can shift modulation pattern seamlessly from sinusoidal pulsewidth modulation (SPWM) to discontinuous PWM (DPWM). The modulation scheme is generalized at each degree of discontinuity to ensure minimum switching losses for variable load power factors. Additionally, a hybrid voltage balancing strategy, which comprises two sets of compensating offset signals with complementary features, has been introduced to mitigate voltage deviation problem at neutral point of the inverter. The unique feature of the proposed hybrid balancing approach is that it generates uniform compensating neutral current regardless of the level of discontinuity. This results in identical and predictable voltage balancing dynamics for the entire modulation transition covering SPWM and DPWM. It has been shown that the proposed hybrid balancing strategy does not lose its unbalance compensation strength even during transition from one modulation pattern to another. The effectiveness of the proposed scheme for wide variations in operating conditions is studied through extensive simulation, and validated in experimentation using a prototype NPC inverter with induction motor loads. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a zero-sequence circulating current (ZSCC) control scheme for the multiparalleled three-level T-type inverters (3LT2Is). Based on the analysis with the proposed generalized model of multiparalleled 3LT2Is, it is seen that the ZSCC is influenced by the circuit parameters, duty cycles, and the circulating currents of the l th and first 3LT2I. To mitigate the circulating currents, a deadbeat control strategy for n-paralleled (n≥3) inverters is proposed, which is realized by adjusting the duty cycle of the small vectors in each PWM sampling period. Compared with the conventional PI control method, the ZSCC spike is mitigated with the proposed scheme, thus improving the quality of the output currents. Also, the reliability of the 3LT2Is system is improved because such a scheme only needs the information about the ZSCC and zero-sequence duty ratio in the l th and the first inverter. The proposed method can also be applied to the neutral-point-clamped converters. Simulation and experimental results verify the effectiveness of the theoretical analysis and the proposed method. [ABSTRACT FROM PUBLISHER]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

Exploiting the rich switching redundancies of the dual inverter, new hybrid pulsewidth-modulation (PWM) switching methods are proposed in this paper using the degree of freedom of operating the individual inverters independently, in addition to exercising the degree of freedom of controlling the switching action of the individual legs independently. Two voltage entities, namely, common-mode voltage (CMV) and differential-mode voltage are identified in the dual inverter, and all hybrid PWMs are envisaged aimed at reducing and also eliminating the CMV in it. The effects of such attempts on motor shaft voltage and also the motor bearing currents are presented in detail. Furthermore, bearing current profiles of an open-end winding induction motor are also presented with both conventional and hybrid PWMs proposed in this paper. Electric discharge machining discharge currents are completely eliminated with the use of all hybrid PWM methods proposed in this paper. In addition, implications of completely eliminating the CMV are also presented in this paper. All hybrid PWMs proposed in this paper are first simulated using MATLAB and are experimentally verified on a dual two-level inverter feeding a 1.1-kW 415-V 3- $\phi$ open-end winding induction motor drive. [ABSTRACT FROM PUBLISHER]

Multilevel inverters with dodecagonal (12-sided polygon) voltage space vector structure have advantages, such as complete elimination of fifth and seventh harmonics, reduction in electromagnetic interference, reduction in device voltage ratings, reduction of switching frequency, extension of linear modulation range, etc., making it a viable option for high-power medium-voltage drives. This paper proposes two power circuit topologies capable of generating multilevel dodecagonal voltage space vector structure with symmetric triangles (for the first time) with minimum number of dc-link power supplies and floating capacitor H-bridges. The first power topology is composed of two hybrid cascaded five-level inverters connected to either side of an open-end winding induction machine. Each inverter consists of a three-level neutral-point-clamped inverter, which is cascaded with an isolated H-bridge making it a five-level inverter. The second topology is for a normal induction motor. Both of these circuit topologies have inherent capacitor balancing for floating H-bridges for all modulation indexes, including transient operations. The proposed topologies do not require any precharging circuitry for startup. A simple pulsewidth modulation timing calculation method for space vector modulation is also presented in this paper. Due to the symmetric arrangement of congruent triangles within the voltage space vector structure, the timing computation requires only the sampled reference values and does not require any offline computation, lookup tables, or angle computation. Experimental results for steady-state operation and transient operation are also presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

In this paper, a real-time implementation of selective harmonic elimination pulsewidth modulation (SHEPWM) using generalized Hopfield neural network (GHNN) as applied to the single-phase inverter is designed and discussed. Finding the location of the switching instants in the case of SHEPWM involves the solution of a set of nonlinear algebraic transcendental equations. The problem is redrafted as an optimization problem, and it is solved by using GHNN. Though, in principle, the $n$ number of harmonics can be eliminated using the presented methodology, this paper tries for the case of the elimination of the 5th-, 7th-, 11th-, and 13th-order harmonics while retaining the desired fundamental. An energy function is formulated for this problem and the set of ordinary differential equations (ODEs) describing the behavior of GHNN is obtained. A program in KEIL C was developed to solve these systems of ODEs by the Runge–Kutta fourth-order method to give the switching instants for continuously varying modulation indexes $(M)$. A MATLAB simulation was carried out, and an experimental setup was also constructed in order to validate the simulated results. The fast Fourier transform analysis of the simulated output voltage waveform and the experimental output voltage waveform confirms the effectiveness of the proposed method. Hence, the proposed method proves that it is much applicable in the industrial applications by virtue of its suitability in real-time applications. [ABSTRACT FROM PUBLISHER]

A two-motor drive, supplied by a five-leg inverter, is considered in this paper. The independent control of machines with full dc-bus voltage utilization is typically achieved using an existing pulsewidth modulation (PWM) technique in conjunction with field-oriented control, based on PI current control. However, model predictive control (MPC), based on a finite number of control inputs [finite-control-set MPC (FCS-MPC)], does not utilize a pulsewidth modulator. This paper introduces three FCS-MPC schemes for synchronous current control in this drive system. The first scheme uses all of the available switching states. The second and third schemes are aimed at reducing the computational burden and utilize a reduced set of voltage vectors and a duty ratio partitioning principle, respectively. Steady-state and transient performances are analyzed and compared both against each other and with respect to the field-oriented control based on PI controllers and PWM. All analyses are experimental and use the same experimental rig and test conditions. Comparison of the predictive schemes leads to the conclusion that the first two schemes have the fastest transient response. The third scheme has a much smaller current ripple while achieving perfect control decoupling between the machines and is of low computational complexity. Nevertheless, at approximately the same switching loss, the PI-PWM control yields the lowest current ripple but with slower electrical transient response. [ABSTRACT FROM PUBLISHER]

This paper presents a comparison of two modulation methods for the seven-level switched-capacitor (SC) inverter using series/parallel conversion (SCISPC). The SCISPC is a multilevel inverter which has the less number of switching devices than the conventional multilevel inverters. The level-shifted pulsewidth modulation (PWM) (LS-PWM) was applied to the seven-level SCISPC in the previous research. In this paper, the level- and phase-shifted PWM (LPS-PWM) and the LS-PWM are applied to the seven-level SCISPC, and LPS-PWM is compared with LS-PWM for the seven-level SCISPC. The LPS-PWM has both the characteristics of the phase-shifted PWM (PS-PWM) and the LS-PWM. The voltage reduction during the discharging term of the SCs is reduced by means of the shorter discharging period compared to LS-PWM. The voltage ripple of the capacitors is also reduced, which leads to higher power conversion efficiency. The difference of the two modulation methods is confirmed by the theoretical approach, simulation with PSIM, and circuit experiment. [ABSTRACT FROM PUBLISHER]

Impedance network inverters are the best alternatives for voltage-source and current-source inverters. The boosting capability and the shoot-through solution of such converters make them excellent solutions for various applications. Nevertheless, hard switching forces the converter to operate in low switching frequency, which results in a bulky impedance network. Moreover, the coupling between the shoot-through duty cycle and the inverter modulation index makes a tradeoff between the voltage gain and the modulation index (output voltage harmonics). This paper presents a novel dual switching frequency modulation to mitigate the switching losses of the converter, which results in a more compact impedance network. The proposed method combines a high-frequency pulse width modulation with a low-frequency sinusoidal pulse width modulation (SPWM). Therefore, the switching losses decrease considerably with respect to the conventional simple boost modulation. In addition, the impedance network design frequency remains high, and the network size decreases obviously. The proposed approach removes the interdependence between the shoot-through duty cycle and the inverter modulation index. A comparison between the proposed method and the conventional simple boost method is performed to show its advantages over the conventional method. Finally, experimental results are presented to validate the performance of the proposed method. [ABSTRACT FROM PUBLISHER]

In trasformerless grid-connected photovoltaic (PV) systems, common-mode voltage (CMV) fluctuations cause leakage current flow through the stray capacitance of the PV panels. Shoot-through states in a quasi-Z-source inverter (q-ZSI) increase the amplitude of high-order harmonics of CMV. In this paper, by using the modulation technique based on odd pulse width modulation and minor change in the Z network of the three-phase q-ZSI, the leakage current is blocked. No extra semiconductor element is added. By the proposed technique, CMV is kept nearly constant during switching cycles. The experimental results for CMV analysis in a \text1\;\textkW prototype are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Multilevel inverters (MLIs) have replaced conventional two-level inverters for medium-voltage high-power industrial applications. One of the best modulation techniques for MLIs is the space vector modulation (SVM). Although SVM has its own advantages, it has been overlooked for much simpler carrier-based modulation schemes in the industry. Nearest level modulation (NLM) is a simple alternative, which is functionally similar to SVM. In this paper, a new generalized SVM algorithm is presented, in which the SVM is achieved using the concept of NLM. A generalized switch matrix is introduced to derive gate pulses for the inverter, which further simplifies the algorithm. The algorithm is tested and verified for a three-phase, three-level, and five-level neutral-point-clamped inverters in both simulation and hardware. [ABSTRACT FROM PUBLISHER]

This paper aims to investigate a disturbance-rejection-based model predictive control (MPC) with two flexible modes (i.e., unconstrained mode and constrained mode) for three-phase inverters with an $LC$ filter. A disturbance observer (DOB) is designed to both simplify the prediction model and achieve the robustness against uncertain parameters. First, the unconstrained mode is designed with a simple horizon-one MPC control law to precisely regulate the output voltage in the steady state. Next, the constrained mode is designed with long-horizon MPC to quickly drive the system to the unconstrained mode by further optimizing the modulation stage. Also, the proposed MPC ensures the robustness and optimality in all operating modes. Especially, the overall closed-loop stability with DOB dynamics is proven by using Lyapunov function. Unlike other MPC methods, the long-horizon MPC in the constrained mode is specialized by finite switching sequences of the sector-based space vector modulation. Comparative studies with the conventional linear quadratic regulator are conducted on a prototype test bed with a TI TMS320F28335 DSP. Then, the proposed MPC method verifies fast dynamic response and advanced voltage regulation (i.e., small steady-state errors and low total harmonic distortion) under various load conditions and uncertain parameters. [ABSTRACT FROM AUTHOR]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

Compared with multilevel space vector modulation, level-shifted multicarrier sinusoidal pulsewidth modulation (SPWM) for nested neutral point-clamped (NNPC) inverters requires much less calculations and implementation efforts, but the existing conventional SPWM cannot suppress the severe flying-capacitor (FC) voltage ripples under low output-frequency conditions. In order to solve this problem, a multicarrier-based PWM strategy with complete voltage balance control (VBC) capacity is proposed in this paper. For NNPC inverters operating under low output-frequency conditions, two preprocessing steps, the zero-sequence injection and the modulation-signal rearrangement, are proposed before the comparisons between level-shifted carriers and modulating signals. These preprocessing steps make the average currents flowing through FCs zero, which is beneficial to greatly reduce the FC voltage ripples under low output-frequency conditions. Together with additional VBC, the proposed modulation can assure the FC voltages balanced under the entire output-frequency conditions. Principles and implementation processes of proposed modulation techniques and VBC methodsare elaborated in detail and compared with conventional modulation methods. Both simulation results from a 5-MVA system and experimental results based on a 5-kVA platform are presented to verify the effectiveness. [ABSTRACT FROM AUTHOR]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

For three-phase dual-output dc–ac conversion systems, the nine-switch inverter is one of the most versatile available topologies. Despite some disadvantages, recent studies show that the nine-switch inverter achieves efficiency values equivalent to or higher than its 12-switch counterpart, when operating in certain ranges of the modulation index and displacement angles. The use of proper pulse width modulation techniques is able to increase the efficiency even more, as well as to equalize the loss distribution among the switches, favoring an effective and low-cost thermal design. The available pulse width modulation techniques are complex and do not explore the full capacity of the nine-switch inverter to reduce its losses. For this reason, this paper proposes an unrestricted generalized scalar pulse width modulation for nine-switch inverters. Based on this new generalization, a current peak tracking technique is also proposed, achieving small average number of switchings and the highest overall efficiency when compared with other techniques, likewise a more balanced loss distribution among the switches. Experimental results are carried out to demonstrate the validity of the new generalization and the effectiveness of the proposed technique in reducing the switching losses. [ABSTRACT FROM PUBLISHER]

The impedance-source network converter, utilizing a unique LC network and previously forbidden shoot-through states, provides the ability to buck and boost the input voltage in a single stage. However, the inrush shoot-through current (STC) in startup or transient process might cause undesired current stresses on converter devices. This paper focuses on the STC sensing for an effective inrush current limitation by the combined current sensing technique in the quasi-Z-source inverter. STC and phase currents for the inverter control strategy are obtained simultaneously. No extra hardware is needed and the effects of current sensor bandwidth and duty cycle on the sensing accuracy are analyzed mathematically. The voltage spike gets avoided by integrating the stray inductance into the impedance network. Finally, an STC control loop based on proposed method are embedded in the field-oriented control strategy. The inrush STC and the device current stress in the transient process get suppressed. Simulation and experimental results from a quasi-Z-source inverter validate the feasibility of the proposed methods. [ABSTRACT FROM PUBLISHER]

This paper presents the mathematical and harmonic analyses of output phase voltages of three-phase voltage source inverters which employ a hybrid two-dimensional–threedimensional (2-D–3-D) space vector modulation (SVM) voltage control algorithm. The explicit time-domain representation of the harmonic components in addition to the total harmonic distortion (THD) of the output phase voltages is given in terms of system and control parameters. This paper also investigates the harmonic characteristics and THD performance against the linearity of the modulation region which helps in the harmonic performance and design studies of such inverters employing the hybrid 2-D–3-D SVM. The fundamental component of the output voltages follows the reference with lower THD in the linear modulation region rather than the overmodulation region. Experimental results are used to validate these analyses as well as the effectiveness of the hybrid 2-D–3-D SVM algorithm for generating balanced and low THD phase voltages. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

Neutral-point (NP)-clamped three-level inverter, which is a widely used topology of multilevel converters, suffers from the NP voltage drift as its main technical drawback. The nearest-three-virtual-vector (\NTV^2) modulation method can control the NP voltage balance for any load over the full range of inverter output voltage. However, compared with the nearest-three-vector (NTV) modulation method, \NTV^2 increases the switching frequency. This paper combines \NTV^2 with NTV, and the two methods are used alternately in a fundamental cycle. The duty-cycle coefficients of the redundant small vectors are analyzed to explore the intervals where NTV can control the NP voltage balance in a fundamental cycle. The proportional parameter, which represents the combination of the two methods in hybrid space vector pulsewidth modulation, can be selected to achieve a high-performance NP balance control and low switching frequency. The steady- and transient-state behaviors of the proposed strategy are analyzed in this paper. The experimental results verify the validity of the proposed strategy. [ABSTRACT FROM PUBLISHER]

A dual two-level voltage source inverter (VSI) can synthesize a three-level voltage space vector employing an open-end winding induction motor. Space-vector-based pulsewidth modulation (PWM) variants for this dual VSI are proposed in this paper that offer the dual advantage of limiting the switching power loss to a single VSI at all instants and also reducing the switching commutations in the dual VSI by 50%. The influence of different error volt seconds (affected with different PWM variants) on the motor phase current in the dual VSI is critically analyzed. To this end, two analytical approaches (one using error-voltage trajectory information and the other using switching state information of the dual VSI) are also proposed in this paper to predict the current trajectory and the ripple content in the drive system. Expressions for rms ripple current are developed with different PWM variants. The efficacy of the proposed analytical approaches to predict the current trajectory and the ripple content is confirmed from the experimental results. All the PWM variants are first simulated using MATLAB and verified experimentally by conducting tests on a three-phase open-end winding induction motor drive controlled with volts per hertz control. The implementation of the PWM algorithms only requires instantaneous magnitudes of three-phase reference voltages and completely avoids the sector identification and lookup tables. [ABSTRACT FROM PUBLISHER]

In recent years, high photovoltaic array voltage up to 1000 V and transformerless grid-tied inverter have been increasingly researched and applied to elevate the inverter and the dc power collection efficiency. With the same reasons, a three-level neutral point clamped (3L-NPC) inverter featuring low power device voltage stress and low leakage current becomes increasingly attractive. In this paper, the operation and the features of a novel grid-tied 3L-NPC are presented. The proposed topology is a derivative of the three-level stacked neutral point clamped (3L-SNPC) structure. However, compared with the conventional 3L-SNPC and its pulse width modulation (PWM) strategy, the new topology with novel PWM strategy features completely inactive intrinsic body diodes. Furthermore, only two outer power devices are working with switching frequency, while the other four Insulated Gate Bipolar Transistors (IGBTs) are actually with the grid frequency. Therefore, the relatively high switching frequency is selected to reduce the inverter output filter inductance. A hybrid CoolMosfet and IGBT power module configuration is also proposed based on the new PWM strategy. The calculation shows that the total power device losses are reduced. The experimental results are illustrated in this paper to confirm the operation of the proposed topology and controller. [ABSTRACT FROM PUBLISHER]

A generalized space-vector-based spread spectrum modulation scheme for multilevel inverters is proposed in this paper. The proposed scheme uses the principle of sigma–delta modulation as applied to analog-to-digital converters (ADCs), based on the view that a multilevel converter could be interpreted as an oversampling ADC. The principle of vector quantization is utilized for quantizing the instantaneous reference voltage space vector in the proposed space-vector-based sigma–delta converter. The switching vectors of the inverter are naturally selected without sector identification, ensuring optimum switching sequence under all conditions including the overmodulation region. As the sigma–delta converter results in a randomly varying switching frequency, the proposed scheme has spread spectrum characteristics. To avoid fractional arithmetic, a 60 ^\circ coordinate system is used to represent the space vector in this paper. The proposed scheme can be used for any general n-level inverter, and experimental results are presented for four-, five-, and six-level inverters, driving a 2-hp three-phase induction motor in an open-end winding configuration. The experimental results of the proposed scheme are compared with the space-vector pulsewidth modulation (PWM) scheme and random PWM scheme. [ABSTRACT FROM PUBLISHER]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a unique carrier-based pulse width modulation strategy for a three-level neutral-point-clamped inverter that works satisfactorily and with uniform convergence time over the full power factor (PF) range of the load variation. It has excellent control over capacitor voltages and mitigates low-frequency oscillations in the neutral point for the full PF range. First, an investigation is made to see how the load currents get modulated to generate compensating neutral current causing charging and discharging of dc-link capacitors. It is observed that when an additional modulating voltage signal that is in phase with the corresponding phase current is added in each phase, a neutral current is produced in the right direction which can be used to compensate for any prior unbalance in capacitor voltages. It is demonstrated that the performance of this scheme is insensitive to the load PF variation (full range from zero to unity). It performs satisfactorily throughout the entire linear modulation range and eliminates any undesirable low-frequency harmonic component in the compensating neutral current. The effectiveness of the proposed scheme is verified through simulation and experimental results by varying load PF as well as modulation index with both passive and motor loads. [ABSTRACT FROM PUBLISHER]

In this paper, the near-state pulse width modulation (NSPWM), adapted to be used in dual-voltage source inverter (VSI) fed open-end load, is introduced primarily aiming to appreciably minimize the voltage total harmonic distortion (THD). Within the framework of the proposed method, the active time of pulses at the second inverter is relatively adjusted within switching interval (compared to the first VSI). The phase voltage harmonics are formulated for dual-inverter modulated by NSPWM; then, optimal adjustment is identified via a three-dimensional curve of phase voltage THD versus modulation index (MI) and phase angle displacement (PAD). Due to the limitation of MI in NSPWM, the desired output voltage is synthesized with modifying not only MI but also PAD between references of two VSIs. Furthermore, NSPWM inherently takes advantage of better efficiency compared to conventional space vector modulation due to switching only two phases within an interval (by clamping one phase to positive/negative dc-rail). The dual-VSI supplied by two isolated dc sources is assembled in the laboratory to experimentally evaluate the THD reduction feature of the proposed method; also, the simulation results obtained by means of a MATLAB/Simulink environment show close agreement with experimental data. [ABSTRACT FROM PUBLISHER]

Cascaded converters are adopted in many power systems to manage sources and loads at different voltage levels simultaneously. DC bus capacitor is one of the key components in these converters due to its energy storage and fast response capabilities. However, the ripple current through the capacitor will influence its lifetime and the overall efficiency of the converter. Previous studies showed that the capacitor current of ac systems is optimized when the duty cycles are synchronized under in phase or antiphase condition. In this paper, the bus capacitor ripple current of cascaded two-stage converters for dc systems with different combinations of duty cycles is analyzed. It is found that the optimum capacitor current ripple varies depending on the values of individual duty cycles and the phase-shift angle between them. By properly adjusting the phase shift, the capacitor RMS current value can be reduced without affecting the converter normal operation or the need for extra sensing circuits, hence improving the energy conversion efficiency and prolonging the capacitor lifetime with relatively simple implementation. To illustrate, a case study of a two-stage dc/dc converter is carried out. A laboratory prototype converter confirmed a maximum efficiency improvement of 2.8% if the phase shift is adjusted properly when compared to the same converter with the worst case phase-shift angle. [ABSTRACT FROM AUTHOR]

Multilevel active neutral-point-clamped (ANPC) converter is popularly known for its higher medium voltage drives up to 6.9 kV. However, common-mode voltages (CMV) are generated when using the well-established carrier-based pulse width modulation (PWM) modulation technique. As a result, CMV will become the major cause of the premature bearing failures and the conducted electromagnetic interferences. In this paper, a reduced CMV strategy is proposed for the ANPC which employs an alternatively new hybrid carrier-based modulation named as interleaved sawtooth carrier phase-disposition PWM (ISC-PD-PWM). By doing so, enhanced harmonic profile is achieved as compared to the typically used classical phase-shifted carrier PWM (PSC-PWM). Therefore, a comparative evaluation of the seven-level (7L) ANPC performance using the proposed reduced CMV approach is made between the novel hybrid ISC-PD-PWM and the conventional PSC-PWM in terms of harmonic analysis. The experimental results have proven the feasibility of the proposed concepts with the CMV effectively reduced. Such perceived merits make ANPC be more attractive for its motor drives. [ABSTRACT FROM AUTHOR]

This paper introduces a combination of two proposed efficiency improvement techniques for a microinverter with current mode control zero-voltage switching output stages. The first technique is dynamic dead-time optimization wherein pulse width modulation dead times are dynamically adjusted as a function of load current. The second method is advanced phase skipping control which maximizes inverter efficiency by controlling power on individual phases depending on the available input power from the photovoltaic source. Neither of the techniques requires any additional circuit components and both can be easily implemented in digital controller firmware. The two techniques were designed and implemented in a 400-W three-phase microinverter prototype. The experimental results validate the theoretical analysis of these techniques and demonstrate that a significant efficiency improvement can be achieved by combining the two proposed control techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a new three-phase modular multilevel inverter (MMLI). The proposed inverter consists of repeated modular primary cells that are connected in series configuration. Therefore, the proposed topology can be extended to get more output voltage levels by adding additional cells without increasing voltage stresses across power switches. Both sinusoidal pulsewidth modulation (SPWM) and staircase modulation are successfully applied to the proposed inverter. The proposed inverter features many advantages such as reduced number of semiconductor power switches, driver circuits, dc-voltage sources, simplified control algorithm, and reduced voltage stresses across the switches independent of output voltage level. Furthermore, the performance of the proposed inverter is studied under both open-loop and closed-loop operations for highly inductive load. Beside the obtained simulation results, a laboratory prototype has been carried out and tested to verify the control techniques and performances of the topology. Simulation and experimental results are compared together to highlight the similarity and consistence of them. [ABSTRACT FROM AUTHOR]

Space vector modulation (SVM) control of multilevel inverters (MLIs) is very popular. However, it gets extremely challenging with the increase in the number of output voltage levels due to the emergence of subtriangles in the various sectors of the hexagon, which results in increased computational complexity and storage requirements of switching states and corresponding pulse durations. Currently, this is handled through laborios offline computations in conjunction with the visual inspection of the space vector hexagon and its various sectors. This paper aims to simplify the implementation of the SVM scheme for an n-level MLI by proposing generalized equations that not only facilitate direct online computation of control pulses and obviate the requirement of lookup tables but also result in optimized switching. Yet, the on-time computations of the various MLI switches are still based on simple two-dimensional Cartesian co-ordinate system combined with the basic two-level inverter implementation. The proposed scheme makes use of a unique l-factor approach, which directly identifies the location of the various subtriangles in the space vector hexagon and leads to direct online computations of the control pulses. The proposed scheme is validated by simulations and experimental results for three- and five-level diode clamped MLI. [ABSTRACT FROM AUTHOR]

In high-power traction drive systems, the switching frequency of the inverter is strictly limited owing to the restrictions on switching losses and cooling conditions. In this case, the multimode modulation strategy is usually adopted. Based on the analysis of a modified 24-sector space vector pulse width modulation (SVPWM) technique, several synchronous modulation strategies with different pulse numbers are proposed in this paper, which can be applied to the two-level six-phase voltage-inverter-fed asymmetrical dual-stator induction machines. By comparing the harmonic performance of the synchronized modulations, the authors present a set of multimode SVPWM strategy, which is suitable for the high-power traction drive systems under low switching frequency. At the same time, the switching strategy for transitions between different modulation modes is proposed as well. Simulation and experimental results verify the validity and effectiveness of the proposed synchronized modulation strategies and the switching strategy between different modulation modes. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

A single-phase inverting buck–boost ac–ac converter is proposed in this paper. The proposed converter has no shoot-through and dead-time problems and, like conventional dc–dc converters, it can be operated with simple pulse width modulation (PWM) control. It offers high frequency and high efficiency operation because high speed mosfet can be used as switching device without the reverse recovery issues and losses of its body diode. The proposed converter features quasi-continuous input and output currents, high input power factor, low total harmonic distortion of input and output currents, and high efficiency. A 460 W laboratory prototype was constructed and tested with interleaved and complementary PWM controls using a resistive and inductive load. Detailed experimental results are provided to show the novelty of the proposed converter. Experimental results confirmed that the proposed converter can obtain 93.8% efficiency at 60 kHz switching frequency. [ABSTRACT FROM PUBLISHER]

This paper proposes a unified PWM method for matrix converters so as to establish a common platform which can generate various types of PWM methods in real time by adjusting the free parameters in the modulation algorithm. As a foundation for unification, the general form of the modulation functions for matrix converters is derived using geometric transformation approach. All eligible direct modulation matrices are shown to be of indirect form and are expressed in terms of instantaneous phase quantities. This paper also presents a new viewpoint to consider a matrix converter as a generalized three-level inverter and to apply the double-carrier-based dipolar modulation technique of the three-level inverter to the matrix converter. Several concepts of the two-level PWM inverters are then generalized to the matrix converters for better visualization and understanding of the modulation process. [ABSTRACT FROM AUTHOR]