Search

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

In this paper, eight ultrahigh-voltage gain dc–dc converters are proposed. These sets of converters are derived by the association of boost cells, coupled inductor, voltage multiplier, switched capacitors, and LC filter cells. The nonpulsating input and output converters are evaluated in terms of: principle of operation, voltage gain, voltage and current stress, estimated power losses, and efficiency. Following full analysis prototypes built in the laboratory show experimental results verifying the theoretical analysis. [ABSTRACT FROM AUTHOR]

For an LLC converter, it is difficult to realize the wide output range with conventional pulse frequency modulation control because of the limited operating frequency. This paper proposes a new hybrid control method. The proposed strategy combines the burst-mode control and phase-shift control methods for the LLC converter. The burst-mode control can regulate the output voltage from zero to its maximum value, and the phase-shift control can reduce the increased resonant current during burst-on time. By using this method, the wide output voltage range is realized with the low resonant current during burst-on time and zero-voltage switch (ZVS) for all switches. The reliability and efficiency of the converter can be improved accordingly. The burst duty ratio is regulated by the reference output voltage, and the phase-shift angle is derived when realizing ZVS for lagging-leg switches. Moreover, the resonant parameters and the maximum phase-shift angle are optimized under the constraints of current stress and ZVS condition. This method is easy to be implemented in a low-cost microcontroller because high-frequency real-time calculations are not necessary. A 1.5-kW prototype is built to verify the feasibility and validity of the proposed control method. [ABSTRACT FROM AUTHOR]

This paper presents a new highly integrable hybrid step-down converter that merges switched-inductor and switched-capacitor operations and significantly reduces onboard loss by using the input cable's parasitic inductance as its main inductor. This converter has the inductor placed at the input with a smaller voltage swing, leading to possible use of a smaller inductor and low-voltage rating switches that generally translate to reduced conduction losses. Analyses of converter operation and losses to reveal its original characteristics and design guidelines are presented to facilitate the components optimization. The converter architecture is verified by a proof-of-concept 15-W inductor-less lithium-ion battery charger prototype that uses a 1-m USB 3.0 cable as inductor. The converter, switched at 2 MHz from a 5-V input, experimentally achieves 89.7% peak efficiency and 6% higher efficiency at full load than a Buck converter counterpart. This high efficiency and zero onboard inductor yield a relative 45.7% onboard loss reduction at full load, promising excellent integration feasibility and superior system thermal management. [ABSTRACT FROM AUTHOR]

In a conventional finite control set model predictive control (FCS-MPC) formulation, active and reactive power control loops rely on the predictive controller, whereas the dc-bus voltage is usually governed by a PI-based control loop. This originates from fact that the dynamic equations for describing the predictions of these variables are heavily coupled. In this paper, a cascade-free FCS-MPC for single-phase grid-connected power converters is presented. The proposed control algorithm is formulated in terms of established dynamic references design, which was originally proposed to directly govern active and reactive power, and dc-voltage in three-phase power converters. In this paper, the dynamic reference design concept is extended to control single-phase grid-connected power converters. The proposed control algorithm does not use instantaneous ac-power calculations; instead, it directly formulates the optimal control problem on the grid-current in the original stationary reference frame. The experimental results obtained with a single-phase grid-connected neutral point clamped (NPC) converter confirm a successful design, where system constraints, e.g., maximum power and weighted switching frequency, are easily taken into account. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure for symmetric and cascade multilevel converter is presented. This structure requires the least power electronic components, gate driver circuits, power diode, and dc voltage source. The number of output levels is high. Reduction of the number of power electronic switches against voltage levels is an important factor in multilevel converters due to safety in switches, circuit size, cost, installation area, and complexity in control. To maximize the number of output level in the proposed optimized structure in order to attain different goals, such as reduction of stress on switches, the result of comparing the proposed structure and other structures present. The proposed method is robust against the switching faults in multilevel converter for dc source and the equipment. The simulation and experimental results presented in this paper show the performance of the proposed method. [ABSTRACT FROM AUTHOR]

The large number of semiconductors typically implemented in multilevel converters generates large stray inductances in their commutation loops. As a consequence, high-voltage overshoots appear in the semiconductors during commutation which may limit the operation of the converter. The paper analyzes these overvoltages in the five-level active neutral-point-clamped (5L­ANPC) converter, one of the most popular five level converters and employed by ABB in its ACS­2000 drive. Experimental results show overvoltages almost three times higher than those corresponding to a two-level converter. In order to overcome this problem, the paper presents a new 5L­ANPC with the same characteristics (number of semiconductors, output waveform, switching frequency, efficiency, etc.), but with smaller overvoltages. This is achieved by adding some small capacitors to the busbar that behave like lossless snubbers but with a much simpler implementation. The experimental results illustrate the working principle of these capacitors and demonstrate the reduction of the overvoltages. As a result, the new converter can reach a higher output current or speed-up the commutations reducing, therefore, the losses and increasing the efficiency compared with the previous 5L­ANPC. [ABSTRACT FROM AUTHOR]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

The interleaved bidirectional buck–boost converter dual active half-bridge (IBBC-DAHB) dc–dc converter consists of two converters IBBC and DAHB and a coupled inductor. The IBBC-DAHB converter has significant features such as low ripple current at the low-voltage side, low current stress on the input inductors, voltage stress across the switches less than the high-voltage side, high voltage gain, and zero-voltage soft switching. The converter offers high efficiency using phase-shift modulation when it operates at a nominal design operating point. However, the efficiency decreases due to high circulating current, high current stress, and limited soft-switching range when the source and load voltages deviate from their nominal values. This paper employs both duty cycle and phase-shift modulation methods to improve the above mentioned shortcomings using voltage matching for the DAHB converter. The proposed converter is analyzed and a 500-W experimental prototype with 40–60 V input voltage and 400 V output voltage under 100 kHz switching frequency is implemented to verify the theoretical results. The maximum efficiency of 97.15% is achieved at 60 V and 400 W. A flat efficiency characteristic for the converter is derived by the proposed control method, where the efficiency at 20% of nominal load is 91% and much higher than the phase-shift control, which is 70.8%. [ABSTRACT FROM AUTHOR]

This paper presents a generalized topology for multilevel converters based on flying capacitor multicell structure. The proposed topology consists of two modular high-frequency (HF) and low-frequency (LF) sections or cells. The HF cells consist of flying capacitors and semiconductor switches operating at carrier frequency. The LF cells consist of dc sources and semiconductor switches operating at line frequency and its multiples. The proposed topology can be implemented with arbitrary number HF and LF cells. An important advantage of the proposed topology is its reduced components when compared to other multilevel converter topologies in the same family. Another interesting feature is the relatively low blocking voltage requirement for HF switches, making it an attractive choice for high-power applications. A modulating algorithm is devised to generate the gating pulses for the HF and LF cells using phase-shifted carrier-based pulsewidth modulation. As a particular case, the operation of a 25-level topology is explained by the help of illustrating waveforms. A comprehensive comparative study is presented to illustrate the advantages of the proposed topology in terms of the number of components and other performance criteria. Various simulations are carried out to verify the operation of the proposed topology at different operating conditions. The theoretical analysis is experimentally verified using a scaled-down laboratory setup. [ABSTRACT FROM AUTHOR]

In this paper, an input-series flyback converter with the coupled-inductor-based passive snubber is proposed, where the input-series converter is based on transformer integration, and the passive snubber is composed of inductors, capacitors, and diodes. The inductors of the snubber in various series modules are made on a common magnetic core, and the coupled-inductor scheme is adopted. With the help of the coupled inductor, active input voltage sharing of the input-series converter can also be achieved after the switches are turned off, and voltage sharing of the switch in each series module can be ensured, which overcome the shortcomings of the existing input-series flyback converter. Active voltage sharing processes caused by the coupled inductor are analyzed in detail. Furthermore, the design guideline of the passive snubber is discussed. Finally, the experimental study has been done on a 1500 Vdc/60 W laboratory-made prototype composed of three flyback series modules, and the feasibility of the proposed method and the theoretical analysis is verified by the experimental results. [ABSTRACT FROM AUTHOR]

In this paper, an expandable single-input three-output high step-up dc–dc boost converter is proposed. The voltage conversion ratio of the output ports of the converter can be increased by inductor-diode-capacitor and diode-capacitor cells. The proposed converter can be applied in renewable energy conversion systems, such as in photovoltaic and fuel cells. Also, due to the three output ports of the converter, it can be utilized in portable devices which require high voltage conversions. The main advantage of the proposed converter is supplying loads with different voltages and current ranges due to the expandable structure of the converter. Besides, the proposed converter has the merit of achieving high voltage gains at high frequencies without preselecting wide duty cycles. Furthermore, the proposed converter is able to achieve higher voltage ranges without having any transformer or coupled inductors in its structure; consequently, the related drawbacks are avoided. The switching pattern of the converter is simple and both switches are on and off simultaneously. In this study, a single switching period of the proposed converter, the voltage conversion ratios of the output ports and the expanded form of the structure are analyzed theoretically. Finally, to verify the theoretical results, the experimental results for 40-V input/200-V, 100-V and 360-V outputs with total 600-W output power are extracted and compared with each other. [ABSTRACT FROM AUTHOR]

The conventional design of voltage-source power converters is based on a two-level half-bridge configuration and the selection of power devices designed to meet the full application specifications (voltage, current, etc.). This leads to the need to design and optimize a large number of different devices and their ancillary circuitry and prevents taking advantage from scale economies. This paper proposes a paradigm shift in the design of power converters through the use of a novel configurable device consisting on a matrix arrangement of highly optimized switching cells at a single voltage class. Each switching cell consists of a controlled switch with antiparallel diode together with a self-powered gate driver. By properly interconnecting the switching cells, the switching-cell array (SCA) can be configured as a multilevel active-clamped leg with a different number of levels. Thus, the SCA presents adjustable voltage and current ratings, according to the selected configuration. For maximum compactness, the SCA can be conceived to be only configurable by the device manufacturer upon the customer needs. For minimum cost, it can also be conceived to be configurable by the customer, leading to field-configurable SCAs. Experimental results of a 6 × 3 field-configurable SCA are provided to illustrate and validate this design approach. [ABSTRACT FROM AUTHOR]

In this paper, a self-oscillating soft-switched converter for light-emitting-diode (LED) driver application is presented. In the proposed converter, the self-oscillation conditions are provided with a low number of additional components, and this converter provides a zero-current switching (ZCS) condition for instant switch turn-OFF. This converter does not need additional output current feedback because the output current changes only 10% when the output voltage changes by 33%. The self-oscillating part of this converter applies three low-power BJT and guarantees a soft-switching condition. The proposed self-oscillating control circuit can be implemented with a low cost since it does not need any IC and power supply for the control circuit. The proposed self-oscillating circuit detects the proper moment to turn the switch OFF under the ZCS condition. In order to justify the validity of theoretical analysis, the results of the implemented prototype for driving an LED string are presented. The measured power factor of the prototype shows that, although the input current of the converter is not sinusoidal, this converter can meet the IEC61000-3-2 standard at an operating power of less than 25 W, in addition to having a simple structure and achieving the robust ZCS condition. [ABSTRACT FROM PUBLISHER]

This paper proposes an interleaved buck converter (IBC) with continuous input current, extremely low output current ripple, low switching losses, and improved step-down conversion ratio. Unlike the conventional IBC, the proposed converter has a continuous input current, and its output current ripple is extremely low. The proposed converter has a lower voltage stress in comparison to the conventional IBC and can also provide a high step-down ratio, which makes it a proper choice for high-power applications where a nonisolated step-down converter with low output current ripple and continuous input current is required. Also, the proposed converter can provide current sharing between two interleaved modules without using additional current-sharing control method. All of these benefits are obtained without any additional stress on the circuit components. A prototype converter with 200-V input and 24-V–10-A output is implemented to verify the theoretical analysis. Operational principles and experimental results are presented in this paper. [ABSTRACT FROM PUBLISHER]

Filters for switching ripple attenuation are essential at the input, and sometimes at the output for certain applications, for the deployment of matrix converters (MCs). Due to the absence of inertial elements in the MC structure and the consequent tight input–output coupling, the filter parameters significantly affect its dynamic behavior. This paper presents an exhaustive filter design method for synchronous applications of the MC in power systems. Apart from the usual considerations of ripple attenuation, voltage regulation, reactive current loading, and internal losses, this paper also addresses additional constraints which may be imposed by requirements of dynamic performance and reliable commutation. Rigorous analytical justification of each design step is provided and the sequential design process is summarized. Relevant experimental results are presented to validate the proposed design tool. [ABSTRACT FROM PUBLISHER]

Due to the relatively low output voltage of photovoltaic (PV) source, a high step-up converter with high efficiency is needed when the PV source is connected to the power grid. A novel high step-up converter based on two switched capacitors and a coupled inductor is proposed in this paper. The operating principle is analyzed and the voltage gain is derived. A 100-W prototype is fabricated in the laboratory to verify the theoretical analysis, and the highest efficiency is 96.4%. [ABSTRACT FROM PUBLISHER]

This paper presents an isolated bidirectional interleaved converter with minimum active switches to achieve high conversion ratio. The proposed converter has symmetric structure for easy control, and incorporates two coupled inductors for galvanic isolation and high voltage ratio achievement. A dual-inductor-capacitor-diode (LCD) snubber with common resonant inductor at low-voltage side is in charge of leakage energy recycling for efficiency improvement. In addition, the converter can obtain interleaved terminal current at low-voltage side for lowering current ripples, no matter in boost mode or buck mode. Finally, a 400-W prototype is built for validation, where the experimental results indicate that the highest efficiencies in boost and buck modes are 95.5% and 95.4%, respectively. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved offset selection method for discontinuous-pulse-width-modulation (DPWM)-based back-to-back converters to reduce dc-link current ripple. DPWM is introduced to power converters to diminish the stress on power transistors and prolong their lifespan. However, when using the DPWM method, the dc-link current ripple is increased in nonswitching regions of the power transistors. Moreover, in DPWM-based back-to-back converters, the dc-link current ripple reaches its maximum when the two transistors of both inverters are clamped in opposite directions. Therefore, the dc-link capacitors endure more stress, resulting in decreased life duration. To overcome this issue, the switching method should consider the clamping periods, when the current ripple increases. This can be achieved by modifying the DPWM offset, so that the clamping states of both converters are matched. The effectiveness of the proposed method is confirmed by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new negative output (N/O) buck–boost converter, which can be applied for applications that need wide range of inverse voltage, is proposed. The steady-state, small-signal model and power losses of the proposed converter operating in a continuous conduction mode are analyzed. Comparisons among the traditional buck–boost converter, N/O hybrid buck–boost converter and N/O self-lift Luo converter are presented, and it is found that the proposed converter possesses a widest voltage conversion ratio in these four converters. Finally, a prototype is built, and the simulated waveforms from the PSIM software and the experimental results are presented for validation. [ABSTRACT FROM AUTHOR]

A novel hybrid LLC resonant and dual active bridge (DAB) linear dc–dc converter is proposed as bus converter, which can achieve soft switching and constant output voltage gain at both the open-loop light load and closed-loop heavy load conditions. This paper focuses on its continuous-time average modeling in detail based on the dc output voltage, the first order terms of two transformer currents and the resonant capacitor voltage, which results in a seven-order model. Additionally, the total control-to-output transfer function is derived for the proposed hybrid converter dynamic analysis. The experimental results have verified that the proposed model can correctly match the small-signal frequency response, and compare with DAB, the related analysis based on the proposed model shows the novel hybrid converter can have a better output voltage response. [ABSTRACT FROM PUBLISHER]

Many different topologies based on the multilevel converter approach have been presented in the last decades. In order to obtain improved output waveforms, several modulation techniques have been developed for such converters. Some of those modulation schemes can be directly applied to almost any multilevel converter, while others require significant adaptation in order to be implemented in certain specific converters. This paper presents the implementation of a phase-disposition level-shifted pulsewidth modulation to the recently introduced hybrid multicell converter (HMC). The HMC uses a flying capacitor module on each cell to generate a positive variable dc-link voltage. The variable dc link is inverted at fundamental switching frequency by an H-bridge to generate the cell output voltage. It is desirable to use PD-PWM for its well-known high-performance waveforms. In this paper, a state-machine decoder is developed to balance the floating capacitor voltages and to equalize the supplied power for the series-connected cells of the HMC when using a PD-PWM pattern. Experimental results obtained from a 10-kW prototype are presented, confirming the good-quality waveforms of the HMC modulated with PD-PWM and the adequate balance of all floating capacitors. [ABSTRACT FROM PUBLISHER]

Modular multilevel converter (MMC) is a newly emerging multilevel topology for high-voltage applications during recent years. In this paper, a new MMC is proposed, and the structure and operating principle are analyzed. Owing to the cascaded basic cells without multiwinding transformer, the voltage balancing of floating capacitors must be considered. However, the voltage fluctuation also exists, and theoretical analysis indicates that the amplitude is inversely proportional to the fundamental frequency. This paper has proposed a voltage-fluctuation-suppression method which can reduce the amplitude of the voltage fluctuation in low-frequency region. It can also be used in motor driving with pump/blowerlike load at low frequency and improve the start-up performance significantly. A low-power three-phase five-level prototype is designed and built up to demonstrate the validity of this method. [ABSTRACT FROM PUBLISHER]

A new three-phase single-stage rectifier is proposed in this paper. The outstanding features of the proposed rectifier are that it can produce input currents that do not have deadband regions and an output current that can be continuous when the converter is operating from maximum load to at least half of the load. In this paper, the operation of the new converter is explained, its features and design are discussed in results, and its operation is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

A microconverter serves as a front-end dc–dc stage of a microinverter to convert the power from a photovoltaic module to a dc bus. These front-end microconverters require isolation, high-boost ratio, wide-input voltage regulation, and high efficiency. This paper introduces an isolated resonant converter with hybrid modes of operation to achieve wide-input regulation while still maintaining high efficiency. The proposed converter is designed as a series resonant converter with nominal-input voltage and operates under two additional modes: a boost converter with low-input voltage and a buck converter with high-input voltage. Unlike conventional resonant converters, this converter operates at discontinues conduction mode with a fixed frequency, simplifying the design and control. In addition, this converter can achieve zero-voltage switching (ZVS) and/or zero-current switching (ZCS) of the primary-side MOSFETs, ZVS and/or ZCS of the secondary-side MOSFETs, and ZCS of output diodes under all operating conditions. Experimental results using a 300-W prototype achieve a peak efficiency of 98.1% and a California Energy Commission efficiency of 97.6% including all auxiliary and control power at nominal-input voltage. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

This paper proposes a new power conversion scheme for paralleled server power supplies. The snubber capacitor voltage is utilized for the secondary voltage source, from which bidirectional buck converter provides output power to the load under a very light-load condition. To increase the energy of the secondary voltage source, an additional voltage bus is connected between the snubber capacitors from each power supply. The main advantage of the proposed scheme is that high efficiency can be achieved especially under a very light-load condition because of the low switching and core loss achieved by using the buck converter instead of the conventional structure composed of a primary inverter, an isolation transformer, and a secondary rectifier. Furthermore, the buck converter is integrated into the secondary rectifier circuits, so additional components are minimized. The validity of the proposed converter is confirmed by the experimental results from two 12-V/750-W prototype modules. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

The reduced capability of multilevel converters with more than one intermediate node to balance the dc-link capacitors voltage, as well as the lack of standard modulation methods to improve their balancing performance, makes these converter topologies unattractive for real power applications. This is especially true when the load demands active power. One of these topologies is the five-level multipoint clamped (5L-MPC) converter. The back-to-back (B2B) configuration of two 5L-MPC converters and the use of a space vector modulation (SVM) that exploits the voltage balancing capability of the redundant switching vectors extend the operation conditions range in which a proper voltage balance can be achieved. However, if practical modulation restrictions are considered (limitation of voltage steps, dead times, switching losses, etc.), the voltage balance cannot be achieved for all operation conditions. In this paper, an SVM which takes into account practical restrictions is proposed. In order to guarantee the voltage balance at any operation condition, the grid-side rectifier exchanges reactive power with the grid-side LCL filter. Thus, the voltage balance of the dc-link is guaranteed while a unity grid-side power factor is achieved. The proposed modulation scheme and the voltage balancing strategy are experimentally validated in a 6.6 kV 1.5 MW 5L-MPC B2B converter. [ABSTRACT FROM AUTHOR]

This paper proposes a new configuration for static ground power unit (GPU) based on the novel 25-level hybrid active neutral-point-clamped (HANPC) converter. The superiority of the proposed converter, as compared with conventional and other suggested multilevel converters, is significant decreasing the number of switches and minimizing the number of flying capacitors (FC) in converter. This improvement is possible by using suggested low-voltage submodule converter to the ANPC converter and proposed modulation method. This results in reduction of the size and cost of converter and makes it more feasible and reliable. Applying the active voltage balancing method for FC in the proposed HANPC converter guaranties fast charging and voltage-level regulation of FC without using balance booster circuit. Improving output voltage spectrum leads to inductance reduction of output L–C filter which enhances static GPU performance. The simulation and experimental results verify the validity and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

A new cascade topology for multilevel converter is introduced in this paper which comprises series connection of several submultilevel units. To determine the magnitudes of the dc sources, two new methods are described. The proposed topology is optimized to generate any levels with minimum number of components and peak voltage on switches. The presented topology can be used in high-voltage applications due to using the switches with low voltage rating. To indicate the merits of the proposed structure, comparison studies are provided with other topologies in terms of the number of elements and peak voltage on switches. The comparison results prove that the presented cascade multilevel converter requires fewer components. Moreover, it is shown that the total peak voltage on switches in the proposed topology is less than other structures. Experimental work is presented to demonstrate the performance of the presented multilevel converter. [ABSTRACT FROM PUBLISHER]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a novel four-phase interleaved high step-down converter is presented. The proposed converter can provide an extremely high step-down voltage conversion ratio within a moderate duty cycle. There are four main advantages of the proposed converter. First, the blocking capacitors can store energy as usual. Therefore, they are used as voltage sources to reduce the input voltage as well as to reduce the switch voltage stresses. Second, due to the charge balance of the dc blocking capacitors, the converter possesses an automatic uniform current sharing characteristic of the interleaved phases without adopting any extra circuitry. Third, due to the phase shift between the interleaved phases, the architecture provides a low output current ripple. Fourth, the number of phases can be expanded or reduced to any even phases; therefore, the converter has a wide range of applications. Finally, the operating principles and analysis of this architecture are given, and an experimental prototype is also provided to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

The model predictive control has an ability to achieve multiple control objectives for a modular multilevel converter. This approach has high computational complexity and causes the unwanted switching's leading to a higher ripple in output current and harmonic distortion in output voltage and current waveforms. To solve the issues of computational burden and unwanted switchings, this paper proposes a dual-stage model predictive control approach for a modular multilevel converter. In this approach, the primary objectives are evaluated in first stage corresponding to the redundancy of voltage vectors, while the secondary objectives are evaluated in second stage corresponding to the submodule redundancy. Therefore, the computational burden is significantly minimized without affecting the dynamic response. In addition, a discrete-time model of modular multilevel converter incorporating the common-mode voltage is proposed. The simulation and experimental studies are conducted on a three-phase modular multilevel converter to verify the dynamic and steady-state performance of the proposed approach. The performance comparison between the proposed and conventional model predictive control approach is also presented. [ABSTRACT FROM PUBLISHER]

This paper provides a characterizationr analysis for the voltage balance of modular cascaded converter in a medium-voltage direct-current distribution grid. Specifically, voltage stability and traditional auxiliary resistor solution are analyzed from the theoretical level. On this basis, a minimum voltage tracking balance (MVTB) control based on a switched resistor is proposed. The voltage balance during startup and normal locked processes can be adjusted effectively by MVTB control. Moreover, the resistor does not need to absorb power continuously; instead, it is just switched into operation for a while when a difference occurs, and the power loss can be decreased after the system recovers to a steady state. Finally, experimental results verify the effectiveness of the MVTB control. [ABSTRACT FROM PUBLISHER]

A new resonant converter having low voltage stress and nearly constant efficiency against line variation for high- and wide-input-voltage applications is presented in this paper. It is similar to a three-level zero-voltage-switching pulsewidth modulation converter (TL ZVS PWMC) with two flying capacitors. In the proposed converter, however, two flying capacitors are used as the resonant capacitors, and the output voltage regulation is achieved by frequency modulation. The main advantages of the proposed converter are that, since the sum of the voltages of two resonant capacitors is constant and is equal to half of the input voltage, the voltage across each switch clamps to half of the input voltage and keeps the balance. Moreover, all main switches and rectifier diodes are softly switched under full-line and full-load conditions, and high efficiency can be constantly achieved over a wide input voltage range. These advantages solve the drawbacks on TL ZVS PWMCs. The features, operation principles, and relevant analysis results over a wide input voltage range of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results of a prototype converter with 400–600-V input, 48-V/10-A output, and 200-kHz resonant frequency. The experimental results show that the maximum efficiency of the proposed converter is 95.08% under a full-load and a 600-V input and slightly varies across the 400–600-V input voltage range. [ABSTRACT FROM AUTHOR]

First, the limitations of the conventional interleaved boost converters in high-step-up and high-output-voltage applications are addressed in this paper. Then, a general derivation law of the nonisolated converters from their isolated counterparts is proposed and studied to give a universal solution for high-performance topology deduction. By employing the direct energy transfer concept, a family of nonisolated high-step-up interleaved boost converters is originated to make the turns ratio of a built-in transformer as another design freedom for the voltage gain extension. The derived converters have the advantages of large voltage conversion ratio, low power switch voltage stress, small input current ripple, and zero-voltage-switching soft-switching performance. The steady-state operation of the derived converter is analyzed, and the circuit performance is summarized to explore its advantages in the high-step-up, high-output-voltage, and large-current conversion systems. Finally, a 1-kW prototype with 40-V input and 380-V output voltages is implemented and tested to show the effectiveness of the derived converters. One of the main contributions of this paper is that a clear picture is made on the universal derivation law to generate high-step-up and high-performance dc/dc converters. [ABSTRACT FROM PUBLISHER]

The matrix converter can be used in a wide range of applications. Nevertheless, it does not yet represent a sufficiently mature option for industrialization. In order to resolve this problem, this paper examines the hardware of the matrix converter and identifies all the circuits that should be included in this. It also quantifies the operating conditions and provides practical guidelines for the step-by-step design of a matrix converter. These considerations are validated with experimental results. In this way, it can be said that this paper represents a step forward toward the development of reliable matrix converters for real applications. [ABSTRACT FROM AUTHOR]

This paper proposes a novel family of cascade three-level (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD). The topological family includes buck TL–boost, buck–boost TL, and buck TL–boost TL modes. In order to achieve a reliable TL ac–ac conversion, a double transient voltage feedback control strategy of the output voltage and the voltage across the flying capacitor is introduced in this paper. A 500-VA 220-V \pm10% 50-Hz ac/220-V 50-Hz ac prototype is presented with the experimental results to prove that the converters have four improved advantages simultaneously, including lower voltage across power switches, bidirectional power flow, low THD of output voltage, and higher input power factor. [ABSTRACT FROM AUTHOR]

Multilevel power electronic converters have gained popularity in high-power applications due to their lower switch voltage stress and modularity. Cascaded H-bridge converters are a promising breed of multilevel converters which generally require several separate dc voltage sources. By utilizing the redundant switching states, it is possible to replace the separate dc voltage sources with capacitors and keep only the one with the highest voltage level. Redundancy in the charge and discharge modes of the capacitors is assumed to be adequate for their voltage regulation. However, the effects of the output current of the converter as well as the time duration of the redundant switching states have been neglected. In this paper, the impacts of the connected load to the cascaded H-bridge converter as well as the switching angles on the voltage regulation of the capacitors are studied. This paper proves that voltage regulation is only attainable in a much limited operating conditions that it was originally reported. In addition, based on the analysis of the converter, a simplified formula is found which can be used to find those modulation indices that regulate the voltage of the capacitor. This formula can be used in harmonic minimization problems while capacitor voltage regulation is ensured. Simulation and laboratory results are provided to confirm the analysis. [ABSTRACT FROM PUBLISHER]

This paper introduces a new magnetically coupled single-switch nonisolated dc–dc converter with a high-voltage gain. The topology utilizes magnetic coupling for boosting its output voltage, but unlike other converters with coupled magnetics, its voltage gain is increased by reducing its magnetic turns ratio. The name “Trans-inverse (Tx−1)” is thus used for representing this inverse operating principle of the converter. The converter draws a continuous current from the source and is, hence, suitable for many types of renewable sources. Its leakage energy from the coupled magnetics has further been recycled and transferred to the load by an integrated regenerative snubber circuit. Its inclusion of dc-current-blocking capacitors has also helped to prevent core saturation, which, together with other performance features, has been verified experimentally. [ABSTRACT FROM PUBLISHER]

In this paper, a cascaded H-Bridge (CHB)-multilevel converter (MC)-based photovoltaic (PV) system with no voltage or current sensors at the dc-side is proposed. Eliminating the dc-side sensors simplifies the hardware, leading to lower cost and higher reliability of the PV system. A novel scheme estimating the capacitors’ voltages from the ac output voltage of the inverter is developed. The scheme allows replacing all dc-side voltage sensors by a single-voltage sensor at the ac-side of the converter. Furthermore, the dc current sensors, conventionally required for the maximum power point tracking (MPPT), are also eliminated. Instead, the outputs from the capacitors’ voltage control systems are utilized for the MPPT. The effectiveness of the proposed dc-side sensorless system is experimentally demonstrated on a 2-kW single-phase seven-level CHB converter-based PV system. [ABSTRACT FROM PUBLISHER]

This paper presents a new dual-switch control structure for an ac/dc noninverting cascaded buck–boost power factor correction converter. The proposed converter operates at a discontinuous capacitor voltage mode providing an inherent high-power factor and a zero voltage turn-off switching. Additionally, the proposed control structure enables for a nondistorted sinusoidal current for a wide range of output voltage levels. Unlike the conventional methods, a mode detector is not required and consequently there is no hard transition between buck and boost modes. Although both converter switches are controlled, only one feedback control loop is required to obtain the desired power flow at a unity power factor. The principle of operation, theoretical analysis, simulation, and experimental results of a 1.6-kW prototype grid-connected converter are presented. The results confirmed the validity of the proposed system under various operating conditions. [ABSTRACT FROM PUBLISHER]

A novel complementary phase disposition pulsewidth modulation method for the modular multilevel converter (MMC) with a limited number of submodules is proposed in this paper. Compared with the previous works, more practical issues have been considered, and the corresponding solutions have been provided. First, a new preset PWM signal mapping sequence and an improved virtual loop mapping (VLM) are used in the modulation. This method not only achieves a favorable capacitor voltage balance in the symmetry system but lowers the switching frequency of MMC's devices. Second, to further reduce the switching frequency, the unbalance margin of capacitor voltages is adopted to achieve the switching between the VLM and the selective VLM (SVLM). Moreover, the system robustness has been improved by considering the situation of symmetry losing, like cell fails; in these cases, the capacitor voltages of the upper and lower arms are balanced through the collaboration of the SVLM and the reconfigurable VLM. Finally, the effectiveness of the proposed method has been verified with simulation and experimental studies. [ABSTRACT FROM AUTHOR]

In this paper, a family of three-phase direct pulse-width modulated (PWM) ac–ac converters consisting of buck, boost, and buck–boost converters is proposed. The proposed converters have no commutation problem even if all of the switches are turned on or off simultaneously. They do not use lossy snubbers and do not sense the voltage polarity for commutation, and produce high-quality output voltage waveforms. The proposed converters allow the use of power MOSFETs and fast recovery freewheeling diodes independently. The use of power MOSFETs as active switches and freewheeling diodes with extremely fast recovery features lower the switching losses and enable us to reduce the volume of passive components by increasing switching frequency. The input (or output) filter inductor experiences twice of the converter switching frequency and thus can be designed with minimum size. To increase power density of the proposed converters, a three-phase three-limb coupled inductor is proposed. Three-phase coupled inductor integrates three separate coupled inductors of the proposed converters in one three-limb core. In comparison with separate coupled inductors, the three-phase coupled inductor has a smaller size with large current-handling capability. Experimental results obtained for the boost-type converter show the robustness of the proposed three-phase ac–ac converters. [ABSTRACT FROM AUTHOR]