Search

In this paper, the analysis of space vector modulation of a three-phase/wire/level Vienna rectifier is conducted, according to which the implementation of the equivalent carrier-based pulsewidth modulation is deduced theoretically within each separated sector in the diagram of vectors. The voltage balancing ability of dc-link neutral point, which depends on the uneven distribution of short vectors, is analyzed as well. An adaptive and robust controller to balance the output voltage under the unbalanced load limit for different modulation indices is proposed. The proposed controller can work at wide range of unbalanced load condition as well. Furthermore, the maximum unbalanced load is deduced versus the modulation index m when the converter works in unity power factor. An experimental prototype of 2.5 kW was built to verify the effectiveness of the theoretical analysis. Finally, the tested unbalanced limit of outputs for the experimental platform was given under different modulation indices. The output voltages for dual bus are balanced, and the theoretical analysis is verified. [ABSTRACT FROM PUBLISHER]

This paper proposes a multiple-input versatile matrix converter (VMC) for integrating hybrid ac/dc energy resources and storages to the power grid. The VMC is developed from the traditional indirect matrix converter but operates in the reverse-boost mode rather than in the forward-buck mode. The reverse-boost mode is more relevant here since most renewable sources and energy storages have lower voltages than the grid. The eventual VMC developed uses an alternative nine-switch converter, rather than usual six-switch voltage-source converter, for providing six input terminals in total. One three-phase ac source and three dc sources, or other source combinations, can therefore be connected to the VMC. Powers from these sources are channeled to the three-phase utility grid through the VMC's current-source inverter. Their proper dispatches are guaranteed by the proposed control and modulation schemes, which also help maintain near-sinusoidal input and output current waveforms. Mathematical proofs, simulation, and experimental results have shown that the VMC can indeed operate as intended. [ABSTRACT FROM PUBLISHER]

Efficient energy conversion in low-voltage applications has gained more attention due to increasing energy costs and environmental issues. Accordingly, three-level converters have been discussed as an alternative to the standard two-level voltage-source converter because they offer an increased efficiency at higher switching frequencies. From a system perspective, the benefits of using three-level converters are not only limited to the converter itself, but there are additional positive impacts on the surrounding such as on the load machine losses or on the electromagnetic interference input filter volume. In this paper, a holistic comparison of advanced three-level topologies against the two-level topology is given. Simple analytical calculations and measurements show the benefits and the optimization potential concerning several aspects, such as the necessary semiconductor chip area, the harmonic losses in the load machine and in filter components, and the volume of passive components. [ABSTRACT FROM PUBLISHER]

A novel integrated buck–flyback nonisolated power factor (PF) correction (PFC) converter is proposed in this paper. This new converter is an inherent integration of a buck converter and a flyback converter, which operates in either flyback mode or buck mode according to whether the input voltage is lower or higher than the output voltage. In this way, the dead zones of ac input current in traditional buck PFC converter are eliminated. Therefore, the proposed integrated buck–flyback nonisolated PFC converter can achieve high PF under universal ac input range, and its input current harmonics can easily meet the IEC61000-3-2 Class C limits. The efficiency of the proposed converter is not deteriorated obviously compared to the conventional buck converter. Detailed theoretical analysis and optimal design considerations are presented. A 100-W prototype was built up to verify the theoretical analysis of the proposed integrated buck–flyback nonisolated PFC converter. [ABSTRACT FROM PUBLISHER]

Thanks to the inherent redundancy to generate the different output voltage levels, the multilevel active-clamped (MAC) topology presents an important fault-tolerance ability which makes it interesting for several applications. This paper presents an analysis of the fault-tolerance capacity of the MAC converter. Both open-circuit and short-circuit faults are considered, and the analysis is carried out under single-device and two simultaneous device faults. Switching strategies and different hardware modifications to overcome the limitations caused by faults are proposed. Experimental tests with a four-level MAC prototype are presented to validate the analysis. [ABSTRACT FROM PUBLISHER]

A method for extending the duty cycle range of series-input interleaved forward converter (SII-FC) is proposed in this paper. A family of novel SII-FC topologies is derived by integrating two switching legs, which belong to two forward cells, into one switching leg shared by both the two forward cells in the SII-FC. By employing the proposed method, the derived topologies have the advantages of extended duty cycle, reduced components, and conduction losses, which help to achieve high power density and high efficiency. These advantages make the SII-FC topologies suitable for such applications with wide input voltage range. A series-input interleaved two-switch forward converter (SII-TS-FC) is analyzed in detail, which is a typical SII-FC topology developed by the proposed method. It is composed of two low-voltage switching legs and a high-voltage switching leg. Detailed analysis indicates that the maximum duty cycle of the SII-TS-FC can reach 2/3, which is 1.33 times of that of the two-switch forward converter. The switches of the high-voltage leg can be soft-switched when duty cycle is less than 0.5, while the switches of the low-voltage legs can be soft-switched when duty cycle is larger than 0.5. As a result, high efficiency is achieved over a wide voltage range. In addition, the output filter can be reduced due to the interleaving operation of the two forward cells. The operational principles, characteristics, and design considerations for the proposed SII-FC are presented. Experimental results on the SII-TS-FC prototype with 200–400 V input 48 V/12 A output verify the proposed method and analysis. [ABSTRACT FROM PUBLISHER]

This paper presents the hybrid seven-level cascaded active neutral-point-clamped (ANPC)-based multilevel converter. The converter topology is the cascaded connection of a three-level ANPC converter and an H-bridge per phase. The voltage of the H-bridge is actively maintained to the required level through selection of the switching states of the converter. The topology is operated under selective harmonic elimination pulsewidth modulation (SHE-PWM), maintaining the switching frequency of the converter to a minimum. The operating principles, voltage balancing methods, and limitations of the converter are analyzed together with extensive simulation results of the topology. Experimental results from a low-power laboratory prototype are presented that verify the operation of the hybrid converter under SHE-PWM. [ABSTRACT FROM PUBLISHER]

This paper presents a transformerless solution for front-end rectification, which is particularly suitable for traction applications, requiring high voltages to be stepped down to appropriate dc voltage. The proposed topology is based on pulsewidth-modulation buck rectifier (current source inverter topology) and is capable of rectification and stepping down of single-phase ac supply, in a single stage. A new control scheme is proposed to achieve constant dc output voltage and sinusoidal source current, irrespective of large ripples in the dc inductor current. The proposed scheme is configured in single-loop voltage control mode. The relevant small-signal model is derived from the large-signal model using multiorder decomposition. An elaborate procedure of dc filter design is discussed, for circuit operation with minimum energy storage. All analytical results are validated by numerical simulation for sinusoidal and distorted source voltage. Experimental verification is achieved through a 1.2-kW grid-connected laboratory prototype. [ABSTRACT FROM PUBLISHER]

Unbalanced grids introduce performance deterioration for Vienna rectifier topology by producing twice fundamental frequency ripples in dc-link voltage and input active/reactive power. A common current reference generation for the purpose of eliminating the input power ripple, such as dual-frame hybrid vector control, can maintain constant input power and eliminate ripples in dc-link voltage under light voltage unbalanced grids. Under severe unbalanced grids, this type of a control method will fail to work. This paper first analyzes the theoretical operation area of a constant power control method under unbalanced grids, and then a novel control method is proposed. The proposed control method can work under severe unbalanced grids by injecting a small amount of input power ripple and balance the performance of working area and output dc voltage ripples. Finally, the experiment results using the constant power control method are given and validate the performance of the proposed control method. [ABSTRACT FROM PUBLISHER]

This letter proposes a boost dc–dc converter topology with the novel capability of canceling the input current ripple at an arbitrarily preselected duty cycle. This is accomplished without increasing the count of the number of components in contrast to other solutions available in the literature. In addition, the converter features a high voltage gain without utilizing extreme values of duty cycle or boosting transformers. These features make the converter ideal to process electric power coming from low-voltage power-generating sources, such as renewables. This paper provides details on the principle of operation via topological considerations and a mathematical model. The key factor of reactive component sizing is also discussed in detail. The converter was validated in the laboratory through the construction of a hardware prototype. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

In this paper, a number of alternate-cascaded switched-inductor and tapped-inductor networks have been proposed for Z-source inverters. The resulting topologies have enhanced voltage-boost capability while retaining the usual voltage-buck flexibility of a conventional voltage-source inverter. The enhanced capability is achieved by using lower rated components that can more readily be found. These components are assembled without direct series connection and hence avoid unbalanced voltage sharing problems and losses linked to balancing resistive circuits. The component count is, however, high, meaning that the proposed inverters should only be considered when a design requires multiple lower rated components rather than a few higher rated ones. Analysis, simulation, and experimental results have already validated the concepts discussed. [ABSTRACT FROM PUBLISHER]

Voltage equalization is essential for series-connected energy storage cells, such as lithium-ion cells and supercapacitors (SCs), because it ensures years of service life and maximizes the available energies of cells. Conventional equalizers and multioutput chargers require many switches and/or a multiwinding transformer, which are not desirable in terms of circuit simplicity and extendibility. In this paper, single-switch multioutput chargers based on a combination of an input cell (which generates a square voltage wave) and a voltage multiplier (which produces multiple uniform output voltages) are proposed. A fundamental operation analysis is made, and a dc equivalent circuit is derived to describe their charging and equalization behaviors. Experimental charge tests were performed separately for series-connected SC modules and lithium-ion batteries from voltage-unbalanced conditions. The least charged module/battery was charged preferentially; as a result, all of the modules/batteries were charged to a desired uniform voltage level while eliminating the voltage imbalance. [ABSTRACT FROM PUBLISHER]

Combining concepts of traditional multilevel converter and matrix converter (MC), the multimodular MCs (MMMCs) have reached the medium-voltage high-power level. These topologies possess features such as elimination of dc components and are able to output high-quality multilevel waveforms. Due to the MMMC's particular topological structure, modulation strategies for the conventional converters cannot be directly adopted. This necessitates the design of specially tailored modulation schemes for them to generate sinusoidal input/output waveforms. In this paper, indirect space-vector-based modulation techniques are proposed for the MMMCs. The study begins by establishing an indirect circuit model for the three-module MMMC topology, before using space vector calculations to derive duty ratios for the model's rectification and inversion stages. As the inversion stage can be viewed as multiple sets of three-phase outputs, its switching states and duty ratios are then converted and combined with those from the rectification stage. Finally, the gating signals are produced according to two switching patterns. As demonstrated by simulation and experimental results, the presented modulation techniques can generate sinusoidal waveforms with variable frequency and magnitude, as well as adjustable angle and power factor. The superiority of the second switching pattern is also proved by the obtained results. [ABSTRACT FROM PUBLISHER]

This paper provides a mathematical expression to determine the occurrence of soft-switching for a general topology of zero voltage transition (ZVT) converters with auxiliary resonant voltage source. This expression is used to help the designer in choosing appropriately the values of inductance and capacitance for the auxiliary resonant branch ensuring ZVT. The main advantage of the proposed methodology is to point out suitable sets of circuit parameters without relying only on time consuming numerical simulations of the entire converter. Additionally, numerical methods to compute the time of occurrence of ZVT for these power converters are provided. The proposed methods are given by second-order approximations of a nonlinear function which describes the voltage on the ZVT snubber capacitor during the zero voltage resonant stage. The results can be seen as applications of second-order Taylor series and of quadratic interpolation. However, different from simply finding the root of a given nonlinear equation, the conditions given here provide analytical expressions to compute the time of occurrence of ZVT based on the converter parameters. Then, the proposed conditions become useful for analysis and design, allowing evaluating operation sequence, total commutation time, resistive losses, and other important parameters to describe the converter performance. Experimental results support the analysis presented. [ABSTRACT FROM PUBLISHER]

Fast fault detection and reconfiguration of power converters is necessary in electrical drives to prevent further damage and to make the continuity of service possible. On the other hand, component minimized converters may provide the benefits of higher reliability and less volume and cost. In this paper, a new fault-tolerant converter topology is studied. This converter has five legs before the fault occurrence, and after fault detection the converter continues to function with four legs. A very fast fault detection and reconfiguration scheme is presented and studied. Simulations and experimental tests are performed to evaluate the structure requirements, the digital reconfigurable controller, and fault detection scheme. For experimental tests, the control and the fault detection and reconfiguration schemes are implemented on a single field-programmable gate array (FPGA) chip. Experimental and simulation results show the effectiveness of the proposed fault-tolerant topology and its FPGA-based control. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel three-level voltage-source converter (VSC) as an alternative to known three-level topologies, including the conventional neutral-point-clamped converter (NPCC), many T-type VSCs, and active NPCC. It is shown that, operating in the low converter dc-link voltage range, this new solution not only can achieve higher efficiency than many typical three-level structures but also can overcome their drawback of asymmetrical semiconductor loss distribution for some operating conditions. Therefore, a remarkable increase of the converter output power capability and/or system reliability can be accomplished. The switching states and commutations of the converter, named here as hybrid NPCC (H-NPCC), are analyzed, and a loss-balancing scheme is introduced. Five- and seven-level H-NPCC topologies with loss-balancing features are also presented. Finally, a semiconductor-area-based comparison is used to further evaluate many three-level VSC systems. Interestingly, the total chip area of the proposed H-NPCC is already the lowest for low switching frequencies. [ABSTRACT FROM PUBLISHER]

Domestic induction appliances require power converters that feature high efficiency and accurate power control in a wide range of operating conditions. To achieve this modulation techniques play a key role to optimize the power converter operation. In this paper, a series resonant inverter featuring reverse-blocking insulated gate bipolar transistors and an optimized modulation technique are proposed. An analytical study of the converter operation is performed, and the main simulation results are shown. The proposed topology reduces both conduction and switching losses, increasing significantly the power converter efficiency. Moreover, the proposed modulation technique achieves linear output power control, improving the final appliance performance. The results derived from this analysis are tested by means of an experimental prototype, verifying the feasibility of the proposed converter and modulation technique. [ABSTRACT FROM PUBLISHER]

Multilevel converters have received increased interest recently as a result of their ability to generate high quality output waveforms with a low switching frequency. This makes them very attractive for high-power applications. A cascaded H-bridge converter (CHB) is a multilevel topology which is formed from the series connection of H-bridge cells. Optimized pulse width modulation techniques such as selective harmonic elimination or selective harmonic mitigation (SHM-PWM) are capable of preprogramming the harmonic profile of the output waveform over a range of modulation indices. Such modulation methods may, however, not perform optimally if the dc links of the CHB are not balanced. This paper presents a new SHM-PWM control strategy which is capable of meeting grid codes even under nonequal dc link voltages. The method is based on the interpolation of different sets of angles obtained for specific situations of imbalance. Both simulation and experimental results are presented to validate the proposed control method. [ABSTRACT FROM PUBLISHER]

In this paper, two reduced switch count topologies are introduced for independently supplying two single-phase ac loads with one inverter. Using a new three-switch leg structure recently introduced and implemented in three-phase converters, two types of dual-leg and single-leg topologies are developed which respectively are functionally comparable to two full-bridge and half-bridge inverters working independently though with a less number of semiconductor switches and hence control and gate drive circuit components. The proposed six-switch and three-switch topologies are introduced; two modes of equal frequency and different frequency operation each of its own distinctive characteristics are considered for them and their pulse width modulation schemes are elaborated. Comprehensive analyses of power loss profile and output waveform properties are conducted via simulation for the proposed inverters, and the results are compared with full-bridge and half-bridge inverters. To assess the performance of the proposed inverter topologies, working prototypes are built, and the experimental results are provided. [ABSTRACT FROM PUBLISHER]

Parallel operation is an effective way to improve the capacity of full power converter in permanent-magnet direct-drive wind power generation system. But it causes the zero-sequence circulating-current (ZSCC), which brings current discrepancy, current waveform distortion, power losses, and electromagnetic interference (EMI), etc. The paper proposes a new topology of full power converters which are composed of n full power converters. The n converters have the same structures and are in parallel with each other. Besides, the average models of the system are analyzed and the fundamental mechanism of ZSCC generation is given. Based on the above analysis, the control strategy of the system is designed. The simulation and experiment results of two parallel full power converters show the feasibility of the proposed theory and control scheme. [ABSTRACT FROM PUBLISHER]

In this paper, a multilevel current-source inverter (MCSI) topology is analyzed. The issue of constructing a novel modular single-rating inductor MCSI is explored, taking advantage of the features of field-programmable gate arrays (FPGA) for control and gate signal generation. The proposed topology is built with identical modules where all inductors carry the same amount of current, simplifying the construction and operation of industrial applications with higher efficiency. A new state-machine approach, which is easy to implement in an FPGA, and a proper implementation of the phase-shifted carrier sinusoidal pulse width modulation (PSC-SPWM) allow both current balance in all modules and effective switching-frequency minimization. The performance of the MSCI proposed is simulated with Matlab and is verified by constructing a prototype. [ABSTRACT FROM PUBLISHER]

Multilevel inverters have been widely accepted for high-power high-voltage applications. Their performance is highly superior to that of conventional two-level inverters due to reduced harmonic distortion, lower electromagnetic interference, and higher dc link voltages. However, it has some disadvantages such as increased number of components, complex pulsewidth modulation control method, and voltage-balancing problem. In this paper, a new topology with a reversing-voltage component is proposed to improve the multilevel performance by compensating the disadvantages mentioned. This topology requires fewer components compared to existing inverters (particularly in higher levels) and requires fewer carrier signals and gate drives. Therefore, the overall cost and complexity are greatly reduced particularly for higher output voltage levels. Finally, a prototype of the seven-level proposed topology is built and tested to show the performance of the inverter by experimental results. [ABSTRACT FROM PUBLISHER]

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed. [ABSTRACT FROM PUBLISHER]

Multilevel converters can reach medium-voltage operation increasing the efficiency of high-power applications. Among the existing multilevel converter topologies, the modular multilevel converter (MMC) provides the advantages of high modularity, availability, and high power quality. Moreover, the main advantage compared to cascaded multilevel converters is the lack of an input transformer which results in a reduction of cooling requirements, size, and cost. One of the drawbacks of this topology when used as an ac–ac converter is the input and output frequency components in the control loop, resulting in a more complex controller design. In this paper, a single-phase ac–ac MMC predictive control approach is proposed. The controller minimizes the input, output, and circulating current errors and balances the dc voltages. Experimental results show the performance of the proposed predictive control scheme. [ABSTRACT FROM PUBLISHER]

An impulse-power generator, which encompasses low-cost and simple configuration, operated in discontinuous conduction mode for driving a tubular field emission lamp (TFEL) is proposed. The proposed system based on flyback topology can provide impulse-power driving to eliminate arcing phenomenon caused by traditional dc voltage driving. Therefore, both the lighting performance and lamp lifespan are improved. This paper also presents a simple feedback mechanism to capture the peak value of the impulse lamp current for stabilizing lamp luminance. Next, an equivalent model of the TFEL is constructed to exhibit its capacitive characteristics. Furthermore, the circuit configuration and mathematical models of each operation mode in a switching cycle are also derived, and detailed design considerations are presented. All the experimental results agree with the computer simulations to verify the validity of the theoretical predictions. [ABSTRACT FROM AUTHOR]

In this paper, a simple and effective way of increasing the efficiency of a three-stage low-frequency dimmable high-intensity-discharge (HID) electronic ballast is proposed. To increase the efficiency at all dimming levels, a modified synchronous-buck converter operating in a new critical conduction mode is presented. The proposed modified topology of the synchronous-buck converter operates in a soft-switching mode and therefore significantly increases the efficiency of the three-stage low-frequency HID electronic ballast at all dimming levels. Analytical and experimental results for a dimmable 400-W HID lamp are presented. [ABSTRACT FROM AUTHOR]

The need for solid-state ac–dc converters to improve power quality in terms of power factor correction, reduced total harmonic distortion at input ac mains, and precisely regulated dc output has motivated the investigation of several topologies based on classical converters such as buck, boost, and buck–boost converters. Boost converters operating in continuous-conduction mode have become particularly popular because reduced electromagnetic interference levels result from their utilization. Within this context, this paper introduces a bridgeless boost converter based on a three-state switching cell (3SSC), whose distinct advantages are reduced conduction losses with the use of magnetic elements with minimized size, weight, and volume. The approach also employs the principle of interleaved converters, as it can be extended to a generic number of legs per winding of the autotransformers and high power levels. A literature review of boost converters based on the 3SSC is initially presented so that key aspects are identified. The theoretical analysis of the proposed converter is then developed, while a comparison with a conventional boost converter is also performed. An experimental prototype rated at 1 kW is implemented to validate the proposal, as relevant issues regarding the novel converter are discussed. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for cascaded multilevel converter based on submultilevel converter units and full-bridge converters is proposed. The proposed topology significantly reduces the number of dc voltage sources, switches, IGBTs, and power diodes as the number of output voltage levels increases. Also, an algorithm to determine dc voltage sources magnitudes is proposed. To synthesize maximum levels at the output voltage, the proposed topology is optimized for various objectives, such as the minimization of the number of switches, gate driver circuits and capacitors, and blocking voltage on switches. The analytical analyses of the power losses of the proposed converter are also presented. The operation and performance of the proposed multilevel converter have been evaluated with the experimental results of a single-phase 125-level prototype converter. [ABSTRACT FROM PUBLISHER]

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to forced commutated converters, their use is restricted in the high voltage/high power range where the performance and cost of forced commutated switching devices are not yet competitive. Hybrid cycloconverters proposed recently are capable of improving the performance of cycloconverters by adding an auxiliary forced commutated inverter with reduced installed power. It will be shown that the new topology is not only able to improve the quality of the output voltage but is also able to enhance the control over the circulating current and, therefore, for some of the cycloconverter arrangements, to improve the input power quality. This paper evaluates the performance of a few standard and hybrid cycloconverter arrangements using both simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a novel matrix converter with one ac input and two ac outputs. The presented topology is based on the traditional indirect matrix converter, but with its rear-end six-switch inverter replaced by a compact nine-switch inverter. With only three extra switches added, the proposed converter can produce two sets of three-phase ac outputs, whose amplitudes, frequencies, and phases can appropriately be regulated. Features such as sinusoidal input and outputs, unity input power factor and minimum commutation count are all retained by the proposed topology, despite having an additional output. Its modulation is realized by the computationally less intensive carrier-based method, whose unique carrier requirements can easily be managed within a programmable logic device. Mathematical proof for validating sinusoidal input and outputs achieved by this modulation technique is also discussed, before being verified in simulation and experimentally, together with other findings. [ABSTRACT FROM AUTHOR]

Multilevel voltage-source converter topologies are widely used today in high-power applications such as medium-voltage drives. On the other hand, studies on matrix converters (MCs) have been mainly limited to the low power range. With the intention to combine benefits from both multilevel structure and direct power conversion, this paper investigates the topologies and operating principles of multimodular MCs (MMMCs). Composed of three-phase-to-single-phase MC (3 \times 2 MC) modules, two versions of MMMCs are presented and studied. Modulation schemes to synthesize sinusoidal waveforms on both input and output sides of the converters are elaborated. Having features such as modular design, relatively low switching frequency, and capability of using low-voltage power semiconductor devices, the presented MMMCs are intended for possible use in higher power applications where four-quadrant operation and fast dynamic response are expected. Simulation and experimental results are provided to verify the validity of the study. [ABSTRACT FROM AUTHOR]

This paper presents first an overview of the well-known voltage and current dc-link converter topologies used to implement a three-phase PWM ac–ac converter system. Starting from the voltage source inverter and the current source rectifier, the basics of space vector modulation are summarized. Based on that, the topology of the indirect matrix converter (IMC) and its modulation are gradually developed from a voltage dc-link back-to-back converter by omitting the dc-link capacitor. In the next step, the topology of the conventional (direct) matrix converter (CMC) is introduced, and the relationship between the IMC and the CMCs is discussed in a figurative manner by investigating the switching states. Subsequently, three-phase ac–ac buck-type chopper circuits are considered as a special case of matrix converters (MCs), and a summary of extended MC topologies is provided, including three-level and hybrid MCs. Therewith, a common knowledge basis of the individual converter topologies is established. [ABSTRACT FROM PUBLISHER]

In this paper, a new three-level (3L) converter is presented. It is called 3L Vienna neutral-point-clamped (3L-VNPC) converter and consists of two stacked high-frequency (HF) commutation cells working with a shared power device. The HF cells are connected to a single-phase switched bridge controlled at low frequency. The 3L-VNPC topology is extended to 3L active VNPC (3L-AVNPC) concept, which is generalized for five levels (5L) and N odd voltage levels (N \L). The proposed multilevel converters can be seen as two cascaded voltage stages. The high-voltage stage is specific to the single-phase switched bridge, while the low-voltage (LV) stage corresponds to the stacked HF cells with shared power devices. The new concept AVNPC is a useful and suitable solution for medium-voltage applications, where small modulation index (M) is as crucial as large M. The analyses of the new converters are verified by simulations both for 3L and for 5L topologies, and their features are generalized for N\L. Experimental results for single-phase 3L-AVNPC converter on an LV test bench are also provided to validate the proper operation of the new concept. [ABSTRACT FROM AUTHOR]

This paper presents a novel multilevel active-clamped converter topology, which is an extension to m levels of the three-level active neutral-point-clamped topology. The operating principle is established through the definition of a proper set of switching states and a transition strategy between adjacent switching states. The benefits of the proposed converter topology and control in comparison to alternative multilevel converter topologies are discussed. The simulation and experimental results of a simple four-level dc–dc converter configuration are presented to illustrate the converter performance features. The experimental results of a four-level three-phase dc–ac converter are also presented to further validate the proposed topology and operating principle. [ABSTRACT FROM AUTHOR]

This paper presents a new three-level topology based on the neutral-point (NP)-clamped converter. An additional leg is added to the basic topology. The main purpose of this leg is to provide the converter with fault-tolerant capabilities. In addition, during normal operation mode, the fourth leg can be used to balance the NP voltage. In this way, the low-frequency voltage oscillations that appear in the NP under some operating conditions are cancelled out effectively. As a result, the modulation strategy of the three main legs of the converter does not have to take care of the voltage balance and can focus on other aspects such as, for instance, minimizing the switching losses of the converter. However, the inclusion of the fourth leg produces some additional losses. A resonant topology is proposed to minimize the switching losses of this leg. Three different fault-tolerant solutions based on the fourth-leg topology are presented. A comparison of these topologies showing their respective advantages and drawbacks is made. Experimental results are presented to show the viability of this approach. [ABSTRACT FROM AUTHOR]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]

This paper proposes a reversible six-phase machine drive system. It is composed of two parallel three-phase to three-phase dc-link converters without isolation transformers. The proposed topology permits one to reduce the harmonic distortion in the input converter and decreases the power processed by converter switches. Furthermore, the proposed configuration can guarantee the feasibility of the system when high-power applications are considered. The model and the control strategy have been developed. The simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

A novel three-phase diode boost rectifier is proposed in this paper. The core of the proposed topology is a power conversion device [the loss-free transformer (LFT)] with two terminals; one input and one output. The input is parallel-connected with the dc bus capacitor, while the output is connected between the rectifier plus rail and the dc bus plus rail. The LFT is controlled in such a way to control the rectifier current and boost the dc bus voltage. In contrast to the ordinary boost rectifiers, the switches of the new boost rectifier are rated on a fraction of the dc bus voltage and a fraction of the input current. It makes this topology very compact and efficient. Power rating, size, and losses depend strongly on the ratio of the dc bus voltage to rectifier voltage (boosting factor). For example, if the boosting factor is low, below 1.5, the power converter efficiency could be 98–99%. The proposed boost rectifier has been analyzed and experimentally verified on a 5.5-kW prototype. The results are presented and discussed. [ABSTRACT FROM AUTHOR]

A newly designed zero-voltage-switching (ZVS) multi-input converter is proposed in this paper. The converter can boost the different voltages of two power sources to a stable output voltage. An auxiliary circuit is employed for achieving turn-on ZVS of all switches in the proposed converter. According to various situations, the operational states of the proposed converter can be divided into two states, including a single-power-supply and a dual-power-supply state. In the dual-power-supply state, the input circuits connected in series together with the designed pulsewidth modulation can greatly reduce the conduction loss of the switches. In addition, the effectiveness of the designed circuit topology and the ZVS properties are verified by experimental results, and the goal of high-efficiency conversion can be obtained. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge converters have found industrial application in the medium-voltage high-power range. In this paper, a generalized modulation technique for this type of converter based on a multidimensional control region is presented. Using the multidimensional control region, it is shown that all previous modulation techniques are particularized versions of the proposed method. Several possible solutions to develop a specific implementation of the modulation method are addressed in order to show the potential possibilities and the flexibility of the proposed technique. In addition, a feedforward version of this technique is also introduced to determine the switching sequence and the switching times, avoiding low harmonic distortion with unbalanced dc voltages. Experimental results are shown in order to validate the proposed concepts. [ABSTRACT FROM AUTHOR]

The focus of this paper is the study of direct alternating-current (ac)–ac converters, beginning by buck, half-bridge, full-bridge, and push–pull converters. From the basic converters, we apply a simple methodology to make the use of switches in commercial configurations possible. Following that, eight voltage restorers supplied either on the line side or on the load side are proposed. A comparative evaluation of these topologies concerning implementation, complexity, and component effort is presented. It is notable that some of the studied topologies are known in the literature and others are new. For one of the presented topologies, the design of a 3-kVA voltage restorer is developed, and experimental results are shown, certifying the correct operation of the drive strategy used. [ABSTRACT FROM AUTHOR]

There is a strong trend in the photovoltaic inverter technology to use transformerless topologies in order to acquire higher efficiencies combining with very low ground leakage current. In this paper, a new topology, based on the H-bridge with a new ac bypass circuit consisting of a diode rectifier and a switch with clamping to the dc midpoint, is proposed. The topology is simulated and experimentally validated, and a comparison with other existing topologies is performed. High conversion efficiency and low leakage current are demonstrated. [ABSTRACT FROM AUTHOR]

In this paper, a three-level three-leg ac–dc–ac converter for single-phase applications is investigated. The operating principles and control strategies for the topology are presented. It is shown that dc-link voltage balancing and its reduction are important objectives in the system design. The proposed pulsewidth modulation (PWM) strategy permits the dc-link capacitor voltage balance and also its reduction. The three-level converter is compared to the two-level converter in terms of rms switch currents, harmonic distortion, losses, and costs. Experimental and simulation results are presented to validate the theoretical studies. [ABSTRACT FROM PUBLISHER]

In this paper, we present the bulk acoustic wave (BAW), the sound–electricity reclamation (SER), and the insertion loss as the three key problems of a wavelet transform processor using surface acoustic wave devices. The solutions to these problems are achieved in this study. The more the number of electrode pairs for the interdigital transducer (IDT) is, the weaker the excited BAW is, so the BAW can be eliminated when the number of electrode pairs for IDT is large enough. The substrate material of a small electromechanical coupling coefficient (ECC) k^2 and the low-impedance load of IDT can eliminate SER. When the output ends of the wavelet transform processors are respectively connected to the amplifiers, their insertion losses can be compensated. X\-112^0Y\ \LiTaO3 (small ECC k^2) is used as a substrate material to fabricate the wavelet transform processor. [ABSTRACT FROM PUBLISHER]

In this paper, a new five-level inverter topology for open-end winding induction-motor (IM) drive is proposed. The open-end winding IM is fed from one end with a two-level inverter in series with a capacitor-fed H-bridge cell, while the other end is connected to a conventional two-level inverter. The combined inverter system produces voltage space-vector locations identical to that of a conventional five-level inverter. A total of 2744 space-vector combinations are distributed over 61 space-vector locations in the proposed scheme. With such a high number of switching state redundancies, it is possible to balance the H-bridge capacitor voltages under all operating conditions including overmodulation region. In addition to that, the proposed topology eliminates 18 clamping diodes having different voltage ratings compared with the neutral point clamped inverter. On the other hand, it requires only one capacitor bank per phase, whereas the flying-capacitor scheme for a five-level topology requires more than one capacitor bank per phase. The proposed inverter topology can be operated as a three-level inverter for full modulation range, in case of any switch failure in the capacitor-fed H-bridge cell. This will increase the reliability of the system. The proposed scheme is experimentally verified on a four-pole 5-hp IM drive. [ABSTRACT FROM PUBLISHER]

This paper focuses on a new high-frequency (HF) link dc-to-three-phase-ac power converter. The least number of switching devices among other HF link dc-to-three-phase-ac converters, improved power density due to the absence of devices of bidirectional voltage-blocking capability, simple commutation requirements, and isolation between input and output are the integral features of this topology. The commutation process of the converter requires zero portions in the link voltage. This causes a nonlinear distortion in the output three-phase voltages. The mathematical analysis is carried out to investigate the problem, and suitable compensation in modulating signal is proposed for different types of carrier. Along with the modified modulator structure, a synchronously rotating reference-frame-based control scheme is adopted for the three-phase ac side in order to achieve high dynamic performance. The effectiveness of the proposed scheme has been investigated and verified through computer simulations and experimental results with 1-kVA prototype. [ABSTRACT FROM PUBLISHER]

This paper presents the conception and analysis of a switch-mode power supply (SMPS) with desirable characteristics of high-frequency isolation, high input power factor, low harmonic distortion, and high efficiency. Nearly unity input power factor can be obtained by using an interleaved boost converter associated with a nondissipative snubber, as high efficiency of the ac–dc front-end stage results. Additionally, a soft-switching full-bridge topology performs the dc–dc conversion, providing isolation to the SMPS by using a high-frequency transformer. By cascading both stages, the aforementioned characteristics are achieved. Theoretical background on each one of the converters is presented, and experimental results obtained from a laboratory prototype are presented and discussed in order to validate the proposal. In addition, the evaluation tests demonstrate the operation with nearly unity power factor, high efficiency, and good dynamic response over a wide load range. [ABSTRACT FROM PUBLISHER]