Search

This paper discusses the analysis and experimental validation of bidirectional Z-source breaker and bidirectional Z-source breaker using coupled inductor for low-voltage dc microgrid application. The proposed topologies use an SCR as a switch to isolate the fault from the system, and LC network to generate required commutation conditions for the SCR under fault conditions. Thus, both topologies are able to isolate the fault naturally within a few microseconds without any fault detection and sensing circuit. In this paper, the breaker operating principle is discussed during fault condition and breaker design criteria are derived. When the breaker is connected in series with power electronic converter, Z-source components offer filtering characteristic. The filtering characteristic offered by the breaker components is analyzed. Functional prototypes are developed for both configurations to validate the breaker performance and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated bidirectional two-switch flyback converter with two integrated non-dissipative inductor–capacitor–diode (LCD) snubbers. In the proposed topology, the main flyback transformer and the LCD snubbers are cross coupled to minimize circulating current that would occur in the non-cross-coupled case, in addition to recycle leakage energy and protect the power transistors. The same current circulation issue also occurs in the bidirectional flyback converter with conventional resistor–capacitor–diode (RCD) snubbers. The main objective of this paper is to illustrate this issue and propose an alternate circuitry to reduce the current circulation and improve the conversion efficiency. The experimental results of a laboratory prototype are reported to verify the design. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

Tap changers are commonly used to maintain the limits in medium-voltage lines. Initially based on electromechanical switches, efforts have been made since the 1990's to reduce maintenance expenses with thyristor-based versions. Among the methods to limit the short-circuiting current in commutating taps, the multiwinding coil has demonstrated, during decades of use in the low-voltage field, to be reliable and cheap. Two previous papers showed that multiwinding changers can be applied to medium-voltage lines up to 34.5 kV, 15 MVA with no parallel or series thyristor association. This paper proposes a new topology, based on a double array of tap switches per phase, allowing for step-up the power from 15 to 36 MVA and insertion in any point of the line with no connection to the head transformer. A comparative cost analysis gives technical and economical results for a typical 10 MVA, 34.5 kV stabilizer demonstrating the advantages of the proposed circuit over the electronic single array topology and the classic mechanical solutions. [ABSTRACT FROM PUBLISHER]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

Microinverters require high voltage gain capability for interfacing the low dc voltage output of photovoltaic (PV) module to single-phase ac grid. A two-stage nonisolated inverter is proposed in this paper, with a first boost stage and a second traditional pulse width modulated grid-tied inverter stage. The proposed boost stage consists of a coupled inductor added with a voltage multiplier to achieve the required high voltage gain at high efficiency and to operate over a wide input voltage range. Among the coupled inductor topologies, adding a clamp circuit is a common solution to limit the voltage spike caused by leakage inductance. In the proposed converter, the resonance between the coupled inductor and voltage multiplier is used to address the issue of voltage spike, thereby reducing both component count and device voltage stress. Detailed analysis and design procedure of the proposed converter is presented in this paper. Experimental results of a 250-W microinverter are presented to validate the proposed converter. [ABSTRACT FROM PUBLISHER]

In applications that demand single-input dual-output (SIDO) or dual-input single-output (DISO) dc–dc converters, employing two separate single-input single-output (SISO) converters is a solution. However, the number of components is doubled, resulting in high overall cost. In order to reduce costs, this paper proposes a novel topology synthesis methodology, with which a variety of SIDO and DISO dc–dc converters with reduced components can be derived. The principle of topology synthesis states that integrated SIDO and DISO dc–dc converters can be easily developed from conventional SISO converters by replacing a diode with a basic cell inclusive of additional input/output port. The principle is effective for many SISO dc–dc converters, and as an example, topology synthesis based on buck, boost, buck–boost, Cuk, sepic, and zeta SISO converters is performed in this paper. In order to achieve better understanding of the proposed converters, the integrated SIDO Cuk converter is specifically analyzed and experimentally verified. In comparison with the conventional scheme of two separate SISO Cuk converters, good cross regulation is retained while the number of diodes, inductors, and capacitors is reduced in the proposed SIDO Cuk converter. In addition, zero-voltage-switching operation of one switch is achieved, contributing to lower switching losses. Finally, a prototype circuit with 48-V input and 156 V/1 A, 24 V/4 A outputs is built to validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A single-phase common-mode transformerless grid-connected photovoltaic (PV) converter, which is based on the integration of two stages, is proposed in this paper. Transformer elimination in grid-connected PV systems has many advantages. It not only reduces cost, size, and weight but also increases the complete system efficiency. Since there is no galvanic isolation between grid and PV array, a leakage current may appear due to the PV parasitic capacitance to the ground, if this is not taken into account in the converter design. This paper presents a dc/dc boost converter integrated with a full-bridge inverter. The integration of these two stages reduces the ground leakage current. The neutral line of the grid is directly connected to the negative terminal of the PV array, eliminating any possibility of leakage current in this terminal. The principle of operation of the transformerless converter is analyzed, and a 200-W topology is experimentally tested. [ABSTRACT FROM PUBLISHER]

In this paper, a new high-efficiency step-up current-fed push–pull quasi-resonant converter is proposed, which is suitable for low-voltage fuel cell power conditioning system. The proposed converter conserves inherent advantages of low-input-current stress and high voltage conversion ratio of the conventional current-fed push–pull converter. All of power devices can achieve soft switching at light load improving the overall efficiency. Moreover, similar features have been obtained with fewer components in comparison with the active-clamped current-fed push–pull converter [37] and current-fed push–pull resonant converter [40], that enabling to reduce the cost and improve system reliability. In addition, the voltage-doubler rectifier is adopted to eliminate the reverse-recovery problem of secondary diodes and provides much higher voltage conversion ratio resulting in small turn ratio of the high-frequency transformer. Detailed operation, analysis, design, comparative study, experimental results, and loss breakdown for the proposed converter are presented in the paper. A 510-W prototype verifies the theoretical analysis and the effectiveness of the proposed concept. [ABSTRACT FROM PUBLISHER]

As the “brain” of the modern photovoltaic power systems, dc solid-state transformers (SSTs) are playing an increasing important role in integrating different photovoltaic modules, batteries, and supercapacitors. This paper aims at improving the conversion efficiency of dc SST for a wide operating range by minimizing the backflow power of the dc SST system. First, the mathematical model of the backflow power from both input and output sides of dc SST is obtained. Then, the penalty function is derived and an enhanced triple phase shift control (ETPS) strategy is proposed to minimize the backflow power for various transmission power and voltage conversion conditions. A comprehensive comparison of the proposed ETPS with other advanced control strategies was carried out through theoretical analysis and experimental tests. Main experimental results are illustrated to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a new four-quadrant (4Q) boost-type converter with the use of active virtual ground (AVG) technology. The presented topology can step up the ac grid voltage to a regulated dc voltage under a stable bidirectional current flow and support the power transmission in either real power or reactive power delivery. With the use of the proposed modulation method, only two high-frequency switches are required through the 4Q operation. Under a full-bridge converter structure, an efficient system can be guaranteed. Also, benefiting from the AVG technology, an LCL filter is formed at the system input over the 4Q operation. Both magnitude of leakage current and grid current ripple are also minimized to a small value. Thus, a high-efficiency and low-noise 4Q converter is guaranteed. The presented topology is successfully implemented on a 750 VA prototype and the performance is experimentally verified on it, which shows good agreement with the theoretical knowledge. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

This paper develops a 200 W two-stage rail grade dc–dc module based on gallium-nitride devices. It converts a wide input voltage (64–160 V) to a constant output voltage (24 V). Different devices and topologies are evaluated for the target application, based on which a two-stage configuration is proposed. The first stage is a two-phase regulated buck converter working under critical mode ($>$ 400 kHz), which is followed by an unregulated 48-V/24-V LLC converter (2 MHz) for 3000-V dc isolation. The voltage regulation is discussed for the buck converter when the inductors are negatively coupled, and then the zero voltage switching (ZVS) extension is explored. However, due to the limitation of the digital controller, a tradeoff is made between the dynamic response and the footprint. The compromise solution is to use a small and slow microcontroller for high frequency control (including voltage regulation, critical mode operation, phase interleaving) and various demands (including soft start-up, external communication, and various protections). Finally, all the required functions are verified in a standalone quarter-brick prototype module. It can achieve 95.1% peak efficiency and 130 W/in $^3$ power density. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

Input-series-output-parallel (ISOP) inverter system is very suitable for high dc input voltage and large ac output current power conversion applications. If this topology is applied to the grid-connected occasion, a bulky-capacity grid-connected inverter can be built with multiple small-capacity standardized inverter modules, which can significantly improve the reliability of the system operation and facilitate system design. In this paper, we investigate an ISOP LCL-type grid-connected inverter system, and put forward an optimized way for the topology of combined LCL filters first. Then, the inverter-side inductor current is carefully chosen as the controlled variable and thus a concise distributed control method is proposed to achieve multiple control objectives. On the basis of the presented distributed control, the redundant control technique is also provided to heighten the reliability of the grid-tied ISOP inverter indeed. Finally, a three-module prototype is built and the experimental results validate the effectiveness of the raised strategy. [ABSTRACT FROM AUTHOR]

In voltage-source converter (VSC) systems, utilization of filter inductors with deep saturation characteristics is often advantageous due to the improved size, cost, and efficiency. However, with the use of conventional current regulation (CCR) methods, the inductor saturation results in significant dynamic performance loss and poor steady-state current waveform quality. This paper proposes the inverse dynamic model (IDM)-based compensation method to overcome these performance issues. The method converts the nonlinear inductor of the plant to a fictitious linear inductor such that linear current regulators can perform satisfactorily. In conjunction, identification of L–R parameters is performed to obtain IDM of the system within an acceptable range of sensitivity yielding satisfactory performance. The performance issues of CCR methods with saturable inductor are demonstrated by simulations and experiments. Then, the proposed method is experimentally verified on a single-phase 1.5-kW grid-connected VSC. The performance improvement over the CCR methods is verified by a detailed comparison of experimental waveforms. [ABSTRACT FROM AUTHOR]

In this paper, a high-efficiency isolated bidirectional interleaved converter (IBIC) is proposed for high step-up and high step-down conversion systems. Two inductors are used in the low-voltage side to reduce the current ripple. The IBIC incorporates an ideal transformer to achieve energy transformation and galvanic isolation; the voltage-doubler circuit in the high-voltage side not only improves the voltage gain but also minimizes the voltage stress of power switches. Clamp capacitors achieve active clamping, and the energy stored in the leakage inductance is recycled. Moreover, some switches are operated with soft-switching and slightly reduced switching losses. The prototype circuit, with low-side voltage $V_{L}$ of 48 V, high-side voltage $V_{H}$ of 380 V, and rated power of 1.5 kW, is implemented to demonstrate the functionality of the proposed IBIC. The peak efficiency levels of the proposed converter in the high step-up and high step-down stages are 95.3 and 95.8%, respectively. [ABSTRACT FROM AUTHOR]

In this paper, several new coupled-inductor-based soft-switching dc–dc converters are proposed. These converters are obtained by changing the coupled branch of several existing dc–dc converters. Meanwhile they have similar characteristics to these existing converters, and provide more choices for the practical application. Then by applying an existing efficiency improvement method, which is used in the buck-type soft-switching converter, to all abovementioned converters, several new converters with efficiency improvement characteristics are obtained. This efficiency improvement method utilizes the low conduction performance of the transistor to reduce the loss. In addition, this method has the same control complexity to original topologies, because the auxiliary transistor has the same control timing to one of main transistors. The characteristic of new converters and efficiency improvement method are presented by analyzing two new topologies (boost-type converters). Finally simulation and experimental results are given and analyzed by designing a prototype. Based on these results, soft-switching conditions and efficiency improvement capability are verified. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]

In this paper, a fully soft-switched bidirectional dc–dc converter is proposed. All semiconductor devices are soft switched, while its control circuit remains pulsewidth modulated. This condition is achieved only by one auxiliary switch. So, the proposed topology has less complexity in comparison with other similar structures. The energy conversion through the proposed topology during buck and boost modes is highly efficient due to achieved soft-switching condition. The auxiliary circuit operates once during each switching cycle. The converter is analyzed and a 250-W laboratory prototype of the proposed converter is constructed. The experimental results are presented that confirm the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

A nonisolated ultra-high step-down interleaved dc–dc converter with low voltage stress and common ground between the input and output ports is proposed in this paper. In order to extend the extremely narrow duty cycle, series capacitors and transformers are applied to the four-phase interleaved buck converter. In addition to extending the duty cycle, the series capacitors clamp the voltage stress across the switches and diodes, which results in using low voltage rating semiconductor components. Additionally, the main switches are turned on under a soft-switching condition. Hence, the conduction and switching losses are reduced and the overall efficiency of the designed converter is improved. Other important strengths of this topology are very low output current ripple due to interleaving and automatic uniform current sharing. The validity of theoretical analysis and converter operation is confirmed by the implementation of a 150 W prototype at 400 V input voltage and 12 V output voltage. [ABSTRACT FROM AUTHOR]

In this paper, a modified asymmetric half-bridge (AHB) isolated converter is proposed, which does not have dc current offset in the transformer. The topology operates in the same way as the conventional half-bridge (HB), using asymmetric pulsewidth modulation with constant frequency. A voltage doubler rectifier is used in the output stage, which avoids the flow of the dc component current in the primary side of the transformer. In order to investigate the application of the proposed topology, a parallel-resonant (PR) version of the modified AHB was tested, which uses the parasitic elements of the transformer, such as the leakage inductance and the winding capacitance, to achieve zero voltage switching in the primary side switches over a wide load range. Theoretical and commutation analysis results are reported and design guidelines are presented herein. Experimental data were obtained from a parallel resonant 1-kW prototype, operating with a 50 kHz switching frequency, 400 V input voltage, and 400 V output voltage, to verify the theoretical study, and 97% efficiency was achieved. The proposed solution was also tested at high voltage, operating with a rated power of 1.8 kW, switching frequency of 50 kHz, input voltage of 400 V and series-connected output voltages, the maximum voltage being 8620 V. [ABSTRACT FROM AUTHOR]

Series–parallel forward dc–dc converter system is a good option in high-voltage high-power applications. A switch fault, in this converter, should be detected as soon as possible, to avoid further damage and save maintenance cost. In this paper, a new switch fault diagnosis method, which treats output inductor voltages as diagnostic criteria, is proposed for this system. With the proposed method, expensive sensors are needless, since diagnostic signal can be easily acquired by adding a small auxiliary winding into inductor magnetic core. Based on the feature of diagnostic signals in such a system, a low-cost diagnostic circuit is designed. The failed module caused by open-circuit fault or short-circuit fault could be detected within one switching period, allowing for an immediate fault-tolerant action. This method also shows generality for different connections and buck-type isolated topologies. Besides, it works reliably under input-voltage variation and load step, and no misdiagnosis will occur during normal dynamic process. Finally, experimental result verifies the effectiveness of this method. The proposed scheme has a good potential to be applied in real applications for its simplicity and robustness. [ABSTRACT FROM AUTHOR]

A novel bidirectional dc–dc converter having high voltage gain capability with high efficiency is proposed in this paper for interfacing storage in a range of applications. The proposed converter steps up (boost) the voltage in one direction while stepping it down (buck) in the other direction of operation. An attractive feature of the proposed converter is the symmetry of its operating modes. It also has inherent soft-switching capability during turn on of the switches, enabling high switching frequency operation. This, coupled with the fact that the proposed converter uses only one coupled inductor for both boost and buck modes, leads to a compact system. A clamped capacitor network is used to recover the leakage energy. Circuit description, design, and loss calculations for both buck and boost modes are explained. The bidirectional converter is designed for a voltage gain of 10 and (1/10) in the boost and buck modes, respectively. A 500 W laboratory prototype of the proposed converter has been developed and tested under rated conditions. Even for a large voltage gain of 10, a peak efficiency in excess of 94% is achieved, which is not possible with conventional converters. All the results of this work are included. [ABSTRACT FROM AUTHOR]

The development of a photovoltaic ac module composed of a high static gain nonisolated dc–dc converter with current source output characteristic followed by an unfolding low-frequency inverter is presented in this paper. The operation of the dc–dc converter with high static gain and with reduced switch voltage is obtained using the Cuk converter integrated with the switched-inductor technique. The nonisolated structure allows the elimination of the volume and losses of the power transformer and leakage inductance, and an output filter configuration is proposed to reduce the high-frequency ground leakage current. The grid-tied inverter operating in a discontinuous conduction mode (DCM) allows a sinusoidal output current with low harmonic distortion (THD = 3.72%) to be obtained without current control loop and without the use of a current sensor at the output. The maximum power point tracking operation is obtained without the use of the current sensor. The DCM operation increases the current stress, but the proposed converter presents two switches and two input inductors sharing the input current in these components. The theoretical analysis, design procedure, and experimental results are presented for a prototype with a dc input voltage Vi = 30 V, an ac output voltage Vo = 127 V, and output power Po = 180 W. [ABSTRACT FROM AUTHOR]

Switched-capacitor converter (SCC) featuring high efficiency and power density has attracted industry interest, but weak output voltage regulation hinders its application. This paper presents an optimized phase-shift (PS) control strategy for a bridge modular SCC, utilized in energy storage system, to obtain continuous conversion ratio and high-efficiency operation. By employing a small inductor as current buffer, the control strategy could be implemented to regulate output voltage conveniently with excellent steady and dynamic performance in step-down mode as well as step-up mode. Most importantly, the high-efficiency operation mechanism never reported before is revealed here. Correspondingly, the active circumfluence could be controlled through optimizing the range of PS time, which will avoid the loss in circuit self. Meanwhile, the soft-switching conditions of all the switches are comprehensively analyzed and soft-switching operations are achieved according to the logic timing control of the power devices, improving efficiency further. Finally, the prototype of the proposed converter was built and the experimental results validated the principle and features of the conversion method. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

The dc–dc modular multilevel converter (MMC), derived from the ac–dc MMC, is an attractive converter topology for interconnection of medium-/high-voltage dc grids. The dc–dc MMC generates an ac voltage component in each arm to drive an ac circulating current for maintaining the energy balance of its submodule capacitors. The power transfer capability of the dc–dc MMC and the amplitude of the ac circulating current are closely coupled with the available arm ac voltage headroom. As the voltage conversion ratio of the dc–dc MMC deviates from 0.5, the power transfer capability of the converter diminishes. This paper proposes an enhanced closed-loop control strategy, which increases the power transfer capability and at the same time reduces the ac circulating current of the dc–dc MMC. Performance and effectiveness of the proposed control strategy are demonstrated by simulation studies in the MATLAB/Simulink as well as experiments conducted on a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a novel integrated interleaved dual-mode time-sharing inverter (IIDMI) is proposed for grid-tied transformerless photovoltaic (PV) applications. While the dual-mode time-sharing conversion technique ensures minimum losses, the IIDMI also retains the advantages of interleaved topologies, such as low total harmonic distortion of the ac current with reduced filtering requirements, increased power density, and reduced current and thermal stresses of power devices. The leakage current problem, which is a main concern with the transformerless PV inverters, is solved by increasing the frequency of the main side band of the common-mode voltage above the resonance frequency of the common-mode impedance, while avoiding high switching losses. The current control, especially at transitions between the buck and the boost modes of operation, is highly improved by utilizing a fast-response deadbeat control scheme. The working principles of the IIDMI are explained in detail, and a 2.2-kW experimental prototype is implemented to confirm the theoretical achievements. [ABSTRACT FROM AUTHOR]

Usually, the parallel-compensated inductive power transfer (IPT) topology fed by a current-source inverter is controlled through variable switching frequency and fixed 50% duty cycle method. This enables the system to operate at resonance frequency, which drifts due to load and other parameter variations. Owing to this control constraint, the load requirements are fulfilled by adding extra dc–dc chopper at the output. This paper presents a new control technique for a parallel–series/series IPT network, fed from a full-bridge current-source inverter to meet the load demand directly by an inverter. Therefore, the extra chopper stage at the output side of the converter is eliminated. The control goals are achieved through a two-loop control method, where the inner input current loop controls the source current and the outer output current loop meets the load requirements. The detailed steady-state operation, converter design, small-signal modeling, and control are reported, and experimental results obtained from a 1.6-kW lab prototype are included to verify the mathematical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-up dc–dc converter is proposed. Active–passive inductor cells (APICs) are used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results. [ABSTRACT FROM AUTHOR]

The success of electric vehicles (EVs) greatly depends on battery size, cost, lifetime, and capacity. The battery capacity of EVs has to contain enough energy to allow EV users to drive, at least, the minimum distance that internal combustion engine vehicles take. However, even with very efficient EVs and combining all the available highly efficient EV technologies, the battery capacity still needs to be large. Thus, one alternative to reduce the battery size is to improve the charging infrastructure by implementing sufficient public/private fast-charging locations, which will significantly increase the EV driving range with relatively low battery capacities. However, this kind of infrastructure requires charging with higher current capability, due to the high power levels involved in the fast-charging process. In this paper, a bidirectional dc/dc converter with six inverter legs connected to a three-phase output is proposed. The converter is similar to a three-phase dual-active-bridge (DAB) converter with more inverter legs in parallel. These additional inverter legs increase the converter current capability, without affecting the DAB main characteristics, preserving similar modulation techniques and DAB advantages. An accurate study about the proposed topology is carried out in this paper, and simulations and experimental results are shown for a 20-kW prototype, validating the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Electric bicycles (EBs) are becoming increasingly popular in some regions such as China and Europe. However, wireless power transfer (WPT) for charging massive EBs poses a challenge related to the cost of WPT system (WPTS), especially in China, where EBs application is so sensitive to the product price. This paper presents an optimization method of the passive components for the S-LCC topology to decrease the cost of the overall system. With the novel method, the number of passive components can be optimized to the minimum and still with constant current and constant voltage outputs. A novel compensation method with an inductor array is also proposed to guarantee an inductive input impedance of WPTS, achieving soft switching and reducing the high switching losses of the high-frequency inverter (HFI). To demonstrate the validity of the proposed methods, an experimental setup is built. The performance of two WPTS indicates that massive EBs can be charged with only one HFI, and the cost of the overall system decreases accordingly. [ABSTRACT FROM PUBLISHER]

High-gain voltage conversion is a feature required for several applications, especially for power processing of low-voltage renewable sources in grid-connected systems. In this scope, the presented paper proposes a novel transformerless high gain step-up dc–dc converter based on an active switched-inductor and a passive switched-capacitor networks. The main advantages of the proposed converter are the high voltage gain (>10), the reduced voltage stresses across the switches and the reduced number of components when compared to topologies that provide the same voltage gain using similar principles. The detailed analysis of the proposed converter and a comparison considering other topologies previously published in the literature are also presented in this manuscript. In order to verify the proposed converter performance, a prototype has been built for a power of 200 W, input and output voltages of 20 and 260 V, respectively, and switching frequency of 50 kHz. Experimental results validate the effectiveness of the theoretical analysis proving the satisfactory converter performance, which peak efficiency is around 95.5%. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In the magnetic resonant wireless power transfer (WPT) technology, system topology is the main factor that determines the WPT characteristics of the system, and recently, various system topologies based on various composite resonant circuits are being applied in WPT applications. This paper groups the composite resonant circuit-based WPT systems into one family and conducts a comprehensive investigation on their topologies and characteristics. First, characteristics of the composite resonant circuits, which are the fundamental circuits of transmitter and receiver of these systems, are investigated; in the process, a calculation method of resonant frequency, current ratio, and quality factor of these circuits are presented and the characteristics of these parameters are clarified. Second, based on that, the composite resonant circuit-based WPT systems are investigated. Possible topologies of these systems are explored and an equivalent system model of these systems is proposed. Based on that, characteristics evaluation expressions of these systems are derived and the optimal design guide of these systems is discussed. Finally, experimental prototypes are constructed and the proposed theory is verified by experiment results. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel boundary conduction mode (BCM) controlled microconverter for photovoltaic (PV) application in order to provide high conversion efficiency over a wide input voltage operating range. Within the wide input range for the PV panel, there is no need to change the operating modes according to the PV panel voltage. The leakage inductance current can work in BCM with fixed switching frequency. The operation mode analysis is given first. Then, the operating principle of the proposed BCM and its implementation are introduced. Loss breakdown of the prototype using GaN devices is analyzed and compared with the same voltage-rating silicon mosfets. A 300-W microconverter was fabricated and experimental results are provided to verify the effectiveness of the proposed BCM control. [ABSTRACT FROM PUBLISHER]

Due to the global environmental issues and energy crisis, the injection of renewable energy sources (RESs) into the power system is continuously increasing. As the interface between RESs and power grid, grid-tied inverters using MOSFET switches, without traditional line frequency transformers, show some potential advantages, in terms of low cost, high efficiency, and lightweight and small size. Among several proposed configurations, the Aalborg inverter was proposed as a new family of high efficiency MOSFET-switch-based hybrid source inverters. For a conventional “half bridge” type Aalborg inverter, due to the imbalance of two independent dc sources, the input dc energies may not be fully utilized, which may reduce the efficiency of whole system. In order to extract the maximum energy from two independent dc sources, a coupled-inductor-based “half bridge” type Aalborg inverter is proposed in this paper. The principle of operation is presented and demonstrated through equivalent circuits. The effectiveness of a new energy balancing technique has been validated through simulations and experiments on a 110 V/ 500 W prototype. [ABSTRACT FROM PUBLISHER]

Microinverters for photovoltaic (PV) modules can improve the energy generation by reducing the effects of shading, since the energy harvesting of each PV module can be controlled individually. In this context, this paper presents a topology of single-stage transformerless grid-connected boost microinverter. It promotes high voltage gain without using a preregulator circuit or a high/low-frequency transformer. A 500 W laboratory prototype was implemented and experimental tests were carried out so that the proposed microinverter was evaluated in a grid-connected PV system. Experimental analysis was performed in order to corroborate the theoretical approach and to verify the effectiveness of the proposed modified Perturb and Observe “Gama” maximum power point tracking technique and the proportional-resonant (P-Res) grid current controller under different irradiation conditions and under partial shading. [ABSTRACT FROM PUBLISHER]

This paper presents a comparative evaluation of eight high-voltage step-up converters based on different associations of boost and zeta standard dc–dc pulse width modulation (PWM) cells. These eight converters present different characteristics such as cascaded and stacked PWM cell associations, as well as isolated winding coupled inductors, tapped winding coupled inductors, and noncoupled inductors. In order to explore the advantages and address the limitations of each topology, several comparative evaluations concerning static voltage gain, power losses, current and voltage stresses, component stress factors, power density, relative cost, and efficiency were carried out. From the theoretical analysis and experimental results, the association named stacked boost–zeta with autotransformer yielded the highest efficiency and power density and resulted in the most attractive converter for the case study. [ABSTRACT FROM PUBLISHER]

In high-voltage output applications, the rectifier diodes in the conventional full-bridge converter have to bear the whole secondary voltage of a transformer. In this paper, a three-level rectifier structure with flying capacitors is proposed for the dc–dc converter. Compared with the conventional dc–dc converter, the converter with the proposed rectifier structure has the following advantages: low-voltage diodes could be used for high-voltage output applications; due to the secondary flying capacitors, there are no voltage spikes on the rectifier diodes even if no snubber circuits are attached; not only can the leading switches realize zero voltage switching (ZVS) as the same as the conventional converters, but also the lagging switches can realize zero current switching in discontinuous-conduction mode and ZVS in continuous-conduction mode; and the rectified voltage has no zero-state voltage, it has been raised to half of the input voltage, so the voltage fluctuation is lower than the conventional converter under the same modulation strategy, and the current ripple of the filter inductor can be reduced by half. The operation principle of the proposed rectifier structure is analyzed in details, and a prototype is fabricated to verify the features of the proposed converter. [ABSTRACT FROM PUBLISHER]

Wireless power transfer (WPT) has drawn more and more attention and has many applications, such as wireless electric vehicle charging systems, which require high power, high efficiency, and high power factor. In this paper, a single-stage WPT resonant converter with bridgeless boost power-factor-correction (PFC) rectifier is proposed to improve efficiency and power quality of line input, and reduce production cost and complexity for high-power WPT system. The bridgeless single-stage topology is creatively proposed to apply in WPT system, which is much more advantageous than conventional two-stage WPT converter with individual boost PFC stage. [ABSTRACT FROM PUBLISHER]

Multilevel current-source inverters have proved to be a high-performance option for industrial applications due to reliability, fault-tolerant capabilities, quasi soft switching, and the use of lower filter capacitor values. One of its major challenges is to balance the internal currents that feed each module. Imbalances could be caused by manufacturing deviations of the reactive components, temperature drift or aging, nonlinear loads, and modulation errors, among others. Using the well-known phase-shift carrier sinusoidal pulse width modulation, a slight change in the amplitude of the carrier signals produces a variation in the average value of the internal currents. In this paper, we introduce a control strategy to balance the current of the inductors and its implementation in a prototype. Simulation and experimental results at different operating conditions show a robust behavior of the control system along with a low distortion in the output voltages and currents of the converter. [ABSTRACT FROM PUBLISHER]