Search

This paper investigates and evaluates the performance of a single-phase split-source inverter (SSI), where an alternative unidirectional dc–ac configuration is used. Such configuration is utilized in order to use two common-cathode diodes in a single device instead of using two separate diodes, resulting in minimum parasitic inductance in the commutation paths. In this paper, the analysis and modulation of the single-phase SSI using this alternative configuration is discussed, and the analysis of the low-frequency component in the dc side is introduced. Moreover, the features behind employing the triangular, the trailing-edge sawtooth, and the leading-edge sawtooth carriers with the single-phase SSI are discussed, and the differences among these carriers are highlighted. In order to highlight the performance of the proposed SSI, a comparative study is conducted with the two-stage architecture and the single-phase quasi-Z-source inverter (qZSI). The introduced analysis is enhanced with simulation results using MATLAB/PLECS models, where a 1-kVA single-phase SSI is designed and simulated. Finally, the designed 1-kVA single-phase SSI is implemented experimentally and tested at different operating points, i.e., at different voltage gains, and a maximum efficiency of $95.5\%$ is obtained. [ABSTRACT FROM PUBLISHER]

The conventional three-level inverter only has voltage buck capability. The quasi-Z-source three-level T-type inverter (QZS 3LT $^2$ I) has been proposed to realize voltage buck–boost operation. In this paper, we further propose a novel modulation scheme for the QZS 3LT $^2$ I to realize voltage boosting, reduce the common-mode voltage (CMV), and control the neutral-point voltage balance simultaneously. The proposed scheme adopts a large vector, a medium vector, a small vector with low CMV magnitude, a zero vector, and a shoot-through vector to generate the output voltage. According to sector number and neutral-point voltage difference, a p-type or n-type small vector with low CMV magnitude is properly selected to balance the neutral-point voltage. Shoot-through states are inserted within zero vector to boost the dc input voltage without affecting the ac output voltage. Dwell times of basic vectors are calculated through the revised volt–second balance equation. Furthermore, a coordinate control strategy between neutral-point voltage balance and voltage boosting is proposed. Doing so, the CMV magnitude can be restricted within one-sixth of dc-link voltage and neutral-point voltage imbalance can be effectively mitigated. The effectiveness of the proposed scheme is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

This paper proposes advanced speed control for a five-leg voltage source inverter (FLVSI) that drives the dual three-phase induction motor system used in industrial manufacturing processes. The advanced speed control method consists of two controllers: 1) The first is a slip controller that satisfies the application requirement, i.e., to control the mechanical speed of two motors equally regardless of the load condition. 2) The second is an angle controller that satisfies the FLVSI requirement, i.e., to control the phase angle difference between the two motors for minimizing the common leg current because the common leg current can be twice higher than other leg's current depending on the operation condition of the dual motor. Stability analysis of the two controllers under advanced speed control is implemented, and the whole performance of the advanced speed control for the FLVSI-fed dual-motor drive system is shown to identify its feasibility through the experimental results. [ABSTRACT FROM AUTHOR]

Connecting legs in parallel in a voltage source inverter is a way to increase the output current and, thus, its rated power. The connection can be made using either coupled or uncoupled inductors, and achieving an even contribution to the output current from all the legs is a crucial issue. Circulating currents produce additional losses and stress to the power devices of the converter. Therefore, they should be controlled and minimized. An efficient technique to attain such balance when coupled inductors are used is presented in this paper. The proposed technique can also be used when the inductors are uncoupled, since it is a particular case where the coupling coefficients are zero. This technique does not include proportional–integral controllers and does not require any parameter tuning either. The exact control action needed to reach current balance is straightforwardly calculated and applied. Experimental results are shown in this paper to verify the efficiency of the proposed balancing method. [ABSTRACT FROM PUBLISHER]

Multilevel inverters with dodecagonal (12-sided polygon) voltage space vector structure have advantages, such as complete elimination of fifth and seventh harmonics, reduction in electromagnetic interference, reduction in device voltage ratings, reduction of switching frequency, extension of linear modulation range, etc., making it a viable option for high-power medium-voltage drives. This paper proposes two power circuit topologies capable of generating multilevel dodecagonal voltage space vector structure with symmetric triangles (for the first time) with minimum number of dc-link power supplies and floating capacitor H-bridges. The first power topology is composed of two hybrid cascaded five-level inverters connected to either side of an open-end winding induction machine. Each inverter consists of a three-level neutral-point-clamped inverter, which is cascaded with an isolated H-bridge making it a five-level inverter. The second topology is for a normal induction motor. Both of these circuit topologies have inherent capacitor balancing for floating H-bridges for all modulation indexes, including transient operations. The proposed topologies do not require any precharging circuitry for startup. A simple pulsewidth modulation timing calculation method for space vector modulation is also presented in this paper. Due to the symmetric arrangement of congruent triangles within the voltage space vector structure, the timing computation requires only the sampled reference values and does not require any offline computation, lookup tables, or angle computation. Experimental results for steady-state operation and transient operation are also presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

This paper proposes an analytical procedure for computation of all pairs of valid switching angles used in pattern generation in five-level H-bridge cascaded inverters. The proposed procedure eliminates harmonic components from inverter output voltage and, for each harmonic, returns the exact boundaries of all valid modulation index intervals. Due to its simple mathematical formulation, it can be easily implemented in real time using a digital signal processor or a field-programmable gate array. In this paper, after a detailed description of the method, simulation and experimental results demonstrate the high quality of achievable results. [ABSTRACT FROM PUBLISHER]

This paper presents an advanced space vector modulation (SVM) strategy for a three-to-five-phase indirect matrix converter (IMC) to reduce common-mode voltage (CMV) with enhanced output performance. By replacing zero and medium voltage vectors with large voltage vectors to synthesize desired output voltage, the five-phase inverter stage modulation can reduce the CMV peak value by 47%, compared with the conventional SVM. In order to compensate the degraded output performance due to the absence of the zero voltage vectors, the rectifier stage modulation is modified by utilizing the two-vector and three-vector modulation techniques. Consequently, by combining the modulations of the rectifier and inverter stages, the proposed modulation strategy can suppress the CMV, as well as improve the output performance of the three-to-five-phase IMC. Simulation and experimental results are provided to verify the effectiveness of the proposed modulation strategy. [ABSTRACT FROM PUBLISHER]

A new space vector modulation, i.e., ZSVM3, for three-phase quasi-Z-source rectifier (qZSR) is proposed. All switches in the three-phase bridge can be turned on and turned off with zero current or zero voltage using the proposed ZSVM3 with no auxiliary circuit. The current through the inductors of the quasi-Z-source network operates in a boundary conduction mode or discontinuous conduction mode to achieve all freewheeling diodes turned off with zero-current switching (ZCS). At the same time, the switch in the quasi-Z-source network can be turned on with ZCS. Besides, the voltage stress of all switches is equal to dc-link voltage. The operation principle of the qZSR is analyzed in detail, and the calculated value of the quasi-Z-source inductor is given. The proposed theory in this paper is verified by a 2-kW prototype. [ABSTRACT FROM PUBLISHER]

Z-source networks are recently being employed to enhance the boosting capability of matrix converters. This paper concentrates on cascaded Z-source ultrasparse matrix converter (ZSUSMC), where the Z-source network is placed between the three-switch input rectifier stage and the six-switch output inverter stage. Two space vector modulation schemes, with and without a zero state in the rectifier stage modulation, are presented and their advantages and disadvantages are discussed. In addition, restrictions imposed on the converter operation in buck mode, which arise from unidirectional nature of the ultrasparse matrix converter, are discussed and a solution is proposed for offsetting those limitations. Furthermore, an optimal switching pattern, which results in minimum possible number of changes in the switching states as well as even distribution of the shoot-through state over the entire control period, is proposed. Also, common-mode voltages of the converter in all possible switching configurations are calculated. Hardware-in-the-loop studies of a ZSUSMC-based permanent magnet synchronous motor drive are carried out to evaluate the performance of the drive under the proposed modulation techniques. The obtained results are compared with a recent study and the superiority of the proposed method in terms of converter input/output current quality is demonstrated. [ABSTRACT FROM PUBLISHER]

In this paper, finite-set model-predictive control (FS-MPC) methodologies for a grid-connected three-level neutral-point-clamped converter are investigated. The proposed control strategies produce fixed switching frequency, maintaining all the advantages of predictive control such as fast dynamic response, inclusion of nonlinearities and restrictions, and multivariable control using a single control loop. The first of the proposed FS-MPC strategies is based on a multiobjective cost function, designed to regulate both the inverter currents and the balancing of the dc-link capacitor voltages. The second FS-MPC strategy is derived from the first one, and it is based on a cost function that regulates only the grid current, with the balancing of the capacitor voltages being realized by controlling the duty cycles of the redundant vectors. The proposed control systems are experimentally validated using a 5-kW prototype. The experimental results show a good performance for both strategies, in steady-state and transient response, with a total harmonic distortion lower than \text2\% for the currents supplied to the grid. [ABSTRACT FROM PUBLISHER]

The hybrid modulation strategy using both low-frequency square-wave modulation and high-frequency pulse-width modulation can extend the stable operating region of a cascaded H-bridge converter. However, it does not control accurately dc voltages of converter but balances them by charging or discharging dc capacitors based on the state of system, which could aggravate fluctuation of dc voltages. If cascaded H-bridge converter is used in photovoltaic field, the aggravated fluctuation on dc capacitor voltages will result in further losses in energy harvesting of solar cells. To address this issue, a modified hybrid modulation strategy is presented in this paper. When dc-bus measured voltages are close to their reference voltages, these H-bridges operate in a zero mode. Adding appropriate zero state can prevent grid current charging or discharging the dc capacitors whose voltages have already reached their control goals. Therefore, the proposed technique is capable of suppressing dc voltage fluctuation, and, thus, improving the output power of solar cells. Simulation and experimental results validate the effectiveness and feasibility of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper aims to investigate a disturbance-rejection-based model predictive control (MPC) with two flexible modes (i.e., unconstrained mode and constrained mode) for three-phase inverters with an $LC$ filter. A disturbance observer (DOB) is designed to both simplify the prediction model and achieve the robustness against uncertain parameters. First, the unconstrained mode is designed with a simple horizon-one MPC control law to precisely regulate the output voltage in the steady state. Next, the constrained mode is designed with long-horizon MPC to quickly drive the system to the unconstrained mode by further optimizing the modulation stage. Also, the proposed MPC ensures the robustness and optimality in all operating modes. Especially, the overall closed-loop stability with DOB dynamics is proven by using Lyapunov function. Unlike other MPC methods, the long-horizon MPC in the constrained mode is specialized by finite switching sequences of the sector-based space vector modulation. Comparative studies with the conventional linear quadratic regulator are conducted on a prototype test bed with a TI TMS320F28335 DSP. Then, the proposed MPC method verifies fast dynamic response and advanced voltage regulation (i.e., small steady-state errors and low total harmonic distortion) under various load conditions and uncertain parameters. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the output stage. A simple unipolar sinusoidal pulse width modulation technique is used to modulate the inverter to minimize the switching loss, output current ripple, and the filter requirements. In general, the main advantages of the new inverter topologies are: 1) the negative polarity of the PV is directly connected to the grid, and therefore, no leakage current; 2) reactive power compensation capability; and 3) the output ac voltage peak is equal to the input dc voltage (unlike neutral-point-clamped and derivative topologies, which requires twice the magnitude of the peak ac voltage). A complete description of the operating principle with modulation techniques, design guidelines, and comprehensive comparisons is presented to reveal the properties and limitations of each topology in detail. Finally, experimental results of 1-kVA prototypes are presented to prove the concept and theoretical analysis of the proposed inverter family for practical applications. [ABSTRACT FROM PUBLISHER]

Transformerless cascaded H-bridge inverters have the advantages of low cost and high efficiency in low-power applications. However, the leakage currents resulting from the parasitic capacitors may increase system losses, electromagnetic interference, and safety concerns. To reduce the leakage current, this paper first establishes the equivalent common-mode circuit of the inverter with the parasitic capacitance and analyzes the characteristics of leakage current in the symmetrical and asymmetrical filter inductance circuit, respectively. The analysis shows that the traditional phase disposition pulse width modulation or phase-shift pulse width modulation cannot solve the leakage current issues, but modifying the modulation methods can eliminate the system leakage current in the symmetrical circuit, and it has a little effect in the asymmetrical circuit. For this reason, a modified phase disposition pulse width modulation for the symmetrical circuit, which can eliminate the leakage current effectively with simple implementation, is proposed. Simulation and experimental results are reported, along with evaluation and comparison results, against a conventional carrier-based pulse width modulation method. [ABSTRACT FROM PUBLISHER]

The cascaded H-bridge converter has been widely used in industry. The ability of dealing with unequal power generation among dc links is necessarily required in many applications, such as large-scale photovoltaic power plants and electric vehicles. In this paper, a novel dc-power control method (PCM) is proposed to keep the ac-current balance and maintain power generation ratios of each dc source at their expected values. A simplified modulation strategy is introduced to implement the proposed method, in which the duration times are modified directly by the correction value derived from the PCM method. To calculate and adjust the power generation ratios, a method based on first-in first-out (FIFO) data queue is utilized. The limitation and ranges of power generation ratio are analyzed in detail. DC power per phase can be controlled accurately by the proposed method in variable-frequency condition, even under larger power generation ratios. Results obtained from simulations and experiments are presented to verify the feasibilities and superiorities of the proposed method. [ABSTRACT FROM PUBLISHER]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

In the paper by Chen et al. (IEEE Trans. Ind. Electron., vol. 66, no. 4, pp. 2837–2846, Apr. 2019), the authors proposed two fault-tolerant control strategies for T-type three-level inverters considering neutral-point (NP) voltage oscillations. However, some basic problems are worth being discussed about the proposed fault-tolerant control methods. This letter presents some comments and results concerning the paper by Chen et al. [ABSTRACT FROM AUTHOR]

This paper presents a capacitor-clamped three-level inverter-based supercapacitor direct integration scheme for wind energy conversion systems. The idea is to increase the capacitance of clamping capacitors with the use of supercapacitors and allow their voltage to vary within a defined range. Even though this unique approach eliminates the need of interfacing dc–dc converters for supercapacitors, the variable voltage operation brings about several challenges. The uneven distribution of space vectors is the major modulation challenge. A space vector modulation method is proposed in this paper to address this issue and to generate undistorted currents even in the presence of dynamic changes in supercapacitor voltages. A supercapacitor voltage equalization algorithm is also presented. Moreover, control strategies of the proposed system are discussed in detail. Simulation and experimental results are presented to verify the efficacy of the proposed system in suppressing short-term wind power fluctuations. [ABSTRACT FROM PUBLISHER]

A new concept of dual-dc-port asymmetrical multilevel inverter (DP-AMI), which is able to interface a low-voltage dc port, a high-voltage dc port, and an ac port simultaneously using only one topology, is presented in this paper. A systematic method to derive the DP-AMI is proposed. With the proposed DP-AMI, a low-voltage dc source, e.g., photovoltaic (PV) modules or battery, can directly supply power to the ac load within single-stage power conversion. Therefore, in comparison with a traditional two-stage dc/ac power conversion system, the power conversion stages are reduced and the voltage/current stress of the front-end dc/dc converter can be significantly alleviated, which can improve the overall conversion efficiency dramatically. Furthermore, by using the low-voltage dc source as a new voltage level, asymmetrical multiple voltage levels are generated by the proposed DP-AMI, which is beneficial for the reducing switching losses and the size/volume of the output filter. The topology derivation method of the DP-AMIs is presented. The operation principles, modulation schemes, and characteristics of one of the proposed DP-AMIs are analyzed in detail. A 1-kW prototype is built and tested to verify the effectiveness and advantages of the proposed method. [ABSTRACT FROM PUBLISHER]

Parallel three-level T-type inverters (3LT2Is) can effectively increase the power rating. However, when multiple 3LT2Is are connected to a single dc bus, the zero-sequence circulating current (ZSCC) will occur. The ZSCC will distort the output currents and increase the system loss. To overcome this drawback, this paper proposes a novel deadbeat control scheme for the ZSCC suppression. A generalized model for analyzing ZSCC in parallel 3LT2 Is is developed for designing the deadbeat control method. The proposed deadbeat control scheme is realized by real time adjusting the dwell time of small vectors in each space vector modulation. Compared to the conventional PI control method, the influence of different sector is eliminated, thus, improving the output current waveform and reducing the ZSCC. The effectiveness of the proposed method is verified by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a modified cascaded neutral-point-clamped grid-connected inverter (MCNPC-GCI) to achieve a wide operational range and high European efficiency in the photovoltaic generation system. Two bidirectional thyristors are added into the standard single-phase cascaded neutral-point-clamped (NPC) inverter to, respectively, connect the positive and negative poles of the two NPC inverters to achieve the transformation between the cascaded NPC inverter and the equivalent single NPC inverter. The losses and grid current total harmonics distortions of the two topology modes are derived to determine their optimal operational ranges and an approach of online smoothly switching the two topology modes is proposed. Detailed experimental results of the proposed MCNPC-GCI are shown to verify its accuracy and feasibility. [ABSTRACT FROM AUTHOR]

The five-phase coupled-inductor inverter is a newly proposed option for three-level five-phase inverter drives. This paper comprehensively analyzes the inverter including the coupled-inductor current, current stress on the dc-link capacitors, and a comparison of these performance aspects using three pulse width modulation (PWM) strategies. Mathematical derivations of the inverter currents and the associated current stress reveal that the current stress is not only influenced by the choice of modulation strategy, as in the neutral-point-clamped topology, but also by the value of coupled inductance; furthermore, the choice of the modulation strategy impacts the core loss of the coupled inductors. Three carrier-based PWM methods are considered: sinusoidal PWM (SPWM), and two methods with the common-mode voltage reduction (referred to as CMVR1 and CMVR2) for the five-phase coupled-inductor inverter. CMVR2 is shown to be the best solution if common-mode voltage reduction is required. The analysis demonstrates that SPWM performs better with respect to current stress and inverter losses, therefore is the preferable modulating strategy for the five-phase coupled-inductor inverter if common-mode voltage reduction is not required. The analysis is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

The reduced capability of multilevel converters with more than one intermediate node to balance the dc-link capacitors voltage, as well as the lack of standard modulation methods to improve their balancing performance, makes these converter topologies unattractive for real power applications. This is especially true when the load demands active power. One of these topologies is the five-level multipoint clamped (5L-MPC) converter. The back-to-back (B2B) configuration of two 5L-MPC converters and the use of a space vector modulation (SVM) that exploits the voltage balancing capability of the redundant switching vectors extend the operation conditions range in which a proper voltage balance can be achieved. However, if practical modulation restrictions are considered (limitation of voltage steps, dead times, switching losses, etc.), the voltage balance cannot be achieved for all operation conditions. In this paper, an SVM which takes into account practical restrictions is proposed. In order to guarantee the voltage balance at any operation condition, the grid-side rectifier exchanges reactive power with the grid-side LCL filter. Thus, the voltage balance of the dc-link is guaranteed while a unity grid-side power factor is achieved. The proposed modulation scheme and the voltage balancing strategy are experimentally validated in a 6.6 kV 1.5 MW 5L-MPC B2B converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel cascaded seven-level inverter topology with a single input source integrating switched-capacitor techniques is presented. Compared with the traditional cascade multilevel inverter, the proposed topology replaces all the separate dc sources with capacitors, leaving only one H-bridge cell with a real dc voltage source and only adds two charging switches. The capacitor charging circuit contains only power switches, so that the capacitor charging time is independent of the load. The capacitor voltage can be controlled at a desired level without complex voltage control algorithm and only use the most common carrier phase-shifted sinusoidal pulse width modulation strategy. The operation principle and the charging–discharging characteristic analysis are discussed in detail. A 1-kW experimental prototype is built and tested to verify the feasibility and effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a harmonic elimination technique based on a three-level dodecagonal space vector structure for open-end winding induction motor (IM) drives with a single-dc supply. Advantages of dodecagonal space vector switching and multilevel inverters are achieved with a single-dc supply. A dc supply-fed three-level flying capacitor (FC) inverter feeds active power to one end of the IM winding terminals and H-bridge connected capacitors eliminate fifth- and seventh-order harmonics from the other end. A pulsewidth modulation (PWM) technique is developed to switch the three-level dodecagonal space vectors and simultaneously control the H-bridge capacitors at 0.1445V\text{dc}. The fifth- and seventh-order harmonics are eliminated for the full modulation range of the three-level FC inverter, including the extreme 6-step operation. An increase in the linear modulation range has been achieved, resulting in improved dc bus utilization. Harmonic elimination is achieved by increasing switching frequency of the low-voltage capacitor connected H-bridge inverter; thus, switching frequency for the high-voltage dc supply-fed FC inverter is not increased. Using the proposed scheme, the instantaneous phase voltage never exceeds \frac23V\text{dc} (maximum phase voltage applied for hexagonal space vector structure) for which the machine windings are rated. Additionally, the proposed inverter has also been shown to operate for field oriented control of the open-end winding IM drive. [ABSTRACT FROM AUTHOR]

Multilevel converters have received more attention recently. Multilevel converters can be used not only in high-voltage high-power applications, but also in energy storage systems, thanks to reduced harmonics and electromagnetic interferences. State-of-charge (SoC) balancing of the storage system cells within cascaded multilevel inverters, e.g., batteries, can be one of the challenges in practical applications. Different methods have been studied and reported in technical literature. However, the SoC balancing is still a challenging issue. In this paper, a new method is proposed to solve this problem by applying several clever but simple changes to the staircase modulation switching scheme without changing the output waveform properties. Validations for this simple method were performed through simulation and experimental prototype. Despite the simplicity of the method, the simulation and experimental results show that SoC balancing of the cells has significantly improved. [ABSTRACT FROM PUBLISHER]

The cost reduction of power-electronic devices, the increase in their reliability, efficiency, and power capability, and lower development times, together with more demanding application requirements, has driven the development of several new inverter topologies recently introduced in the industry, particularly medium-voltage converters. New more complex inverter topologies and new application fields come along with additional control challenges, such as voltage imbalances, power-quality issues, higher efficiency needs, and fault-tolerant operation, which necessarily requires the parallel development of modulation schemes. Therefore, recently, there have been significant advances in the field of modulation of dc/ac converters, which conceptually has been dominated during the last several decades almost exclusively by classic pulse-width modulation (PWM) methods. This paper aims to concentrate and discuss the latest developments on this exciting technology, to provide insight on where the state-of-the-art stands today, and analyze the trends and challenges driving its future. [ABSTRACT FROM PUBLISHER]

Multilevel inverters are gaining more attention in ac drive application due to their many attractive features. In the case of conventional neutral-point-clamped (NPC) or flying capacitor multilevel inverter configurations, active switches are connected in series to produce multilevel output voltage waveform. Therefore, if any one switch fails, the entire configuration has to be shut down; this will reduce the reliability of the system. A dual three-level inverter configuration for induction motor drive is proposed in this paper to improve reliability of the system. This topology is developed by feeding four-pole induction motor stator winding with four conventional two-level inverter modules. A level-shifted carrier-based third harmonic injection pulsewidth-modulation technique is used to produce the gating signals for the proposed configuration. By providing proper phase shift between carrier waves, multilevel voltage waveform is produced across the total motor phase winding, and first center band harmonics are also canceled. Thereby, the torque ripple will be considerably reduced compared with conventional NPC five-level inverter-driven induction motor drive. Finite-element analysis (FEA) is used to estimate the torque ripple when induction motor is supplied by the proposed configuration and conventional five-level NPC inverter configuration to show the effectiveness of the proposed converter. The proposed configuration is simulated using MATLAB/Simulink and experimentally verified using a laboratory prototype with a 5-hp four-pole induction motor drive. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, three overmodulation techniques for the three-to-five-phase indirect matrix converter (IMC) are proposed. The first technique utilizes only the adjacent large vectors in the sector in which the reference output voltage vector lies. The second technique improves on that by continuously adapting vector elimination in the d_2-q_2 vector space based on the output voltage requirements. The third technique utilizes the ripple in the dc link to further reduce the modulation index of the inverter stage during overmodulation. All three techniques increase the voltage transfer ratio of the three-to-five-phase IMC from 0.788 to 0.923, but with the addition of harmonics generated by a vector in the d_2-q_2 vector space of the inverter stage. Simulation and experimental results from a prototype three-to-five-phase IMC validate the three proposed overmodulation techniques. [ABSTRACT FROM AUTHOR]

Multiphase machines are well known for their fault-tolerant capability. Star-connected multiphase machines have fault tolerance in an open circuit. For an inverter switch short-circuit fault, it is possible to keep a smooth torque of a permanent magnet synchronous machine if the currents of the faulty phases are determined and their values are acceptable. This paper investigates fault-tolerant operations of an open-end five-phase drive, i.e., a multiphase machine fed with a dual-inverter supply. Inverter switch short-circuit fault is considered and handled with a simple solution. Original theoretical developments are presented. Simulation and experimental results validate the proposed strategy. [ABSTRACT FROM AUTHOR]

Back-to-back converters have been typically used to interconnect microgrids. For a back-to-back current-source converter, the dc-link current ripple is one of the important parameters. A large ripple will cause electromagnetic interference, undesirable high-frequency losses, and system instability. Conventionally, with a given switching frequency and rated voltage, the current ripple can be reduced by increasing the dc-link inductor, but it leads to bulky size, high cost, and slow dynamic response. To solve this problem, this paper reveals that the current ripple can be significantly reduced by adjusting the gate patterns of space vector modulation between the rectifier and the inverter in a back-to-back converter. The experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

Common-mode voltage (CMV) is one of the most important issues for the power electronics inverters. An interesting space vector modulation of the three-leg current-source inverter has been reported for the CMV reduction recently. However, it has the disadvantages of the bipolar current pulses and modulation index range limitation. In order to solve these problems, a four-leg current-source inverter with a new space vector modulation is proposed in this paper. With the proposed method, the system CMV can be significantly reduced without bipolar current pulses and modulation index range limitation. Finally, the experimental tests are carried out on a four-leg current-source inverter, and the experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

Power converters using deterministic switching frequency schemes have switching noise concentrated at harmonic frequencies, resulting in enhanced electromagnetic emission. To suppress the harmonic spikes in three-phase multilevel voltage source converters, a digital control scheme based on dithered sigma–delta modulation (SDM) is proposed in this paper. Introducing a dithered sequence in an SDM varies the switching frequency randomly, resulting in the suppression of the spurious harmonic spikes in the output spectrum even with a regular control input. Although the switching frequency varies randomly, the minimum pulsewidth of the proposed scheme is the sampling time period, avoiding the minimum pulsewidth problem. Instead of a conventional scalar quantizer, the quantizer in the proposed dithered sigma–delta converter uses the principle of space vector quantization. The proposed scheme is experimentally verified on a constant $v/f$ open-loop induction motor drive for a three-level inverter realized by cascading two two-level inverters. The performance of the proposed scheme is compared with different pulsewidth modulation schemes in the entire modulation index, including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Three-level topologies are widely used in back-to-back converters of wind turbine generation (WTG) systems. In comparison with a conventional two-level topology, three-level topologies have more advantages, particularly for the high power. Neutral-point clamped (NPC) and T-type are typical three-level topologies. An open-switch fault of a three-level rectifier that is connected to a permanent-magnet synchronous generator (PMSG) leads to the current distortion and torque vibration in WTG systems. Furthermore, WTG systems can break down in the worst case. Therefore, a tolerance control for open-switch faults is required to improve the reliability of WTG systems. WTG systems by applying the tolerance control can be stopped safely and prevent additional problems. Depending on the situation, it can keep the operation of WTG systems under open-switch fault. The effects of outer open-switch faults of three-level rectifiers are analyzed by considering PMSG specifications in this paper. Moreover, a tolerance control for outer open-switch faults of the NPC and T-type three-level rectifiers are proposed with existing tolerance controls for inner open-switch faults. The proposed tolerance control is to inject the exact $d$-axis current value to eliminate current distortion. The simulation and experiment are conducted to prove the feasibility of the proposed tolerance control and to identify its performance. [ABSTRACT FROM PUBLISHER]

A new space-vector-based sigma delta modulation scheme for any general $N$-level voltage source inverter is proposed in this paper, which directly quantizes the reference space vector. The proposed scheme uses the sigma delta modulation with the quantizer implemented by the proposed space vector quantizer. A new scheme is proposed for directly quantizing the reference space vector to the multilevel inverter switching vectors without mapping it into two-level inverter vector space. Voronoi regions of the multilevel inverter vector space in the proposed space vector quantizer are defined as a parallelogram with the inverter switching vectors as its vertices. The property of the integer values of the inverter switching vectors in 60 ^{\circ} coordinates is utilized for the direct vector quantization of the instantaneous reference voltage space vector. The proposed scheme is implemented for five-level inverters realized by an open-end-winding induction motor fed with two three-level inverters from either side having symmetrical dc-link voltages, and results are presented. [ABSTRACT FROM PUBLISHER]

This paper presents a novel combined-synchronous-rectifier high-frequency-link (CSR-HFL) inverter. Three types of conventional HFL inverters are analyzed and their performance is summarized. According to one of the conventional HFL inverters, i.e., cycloconverter-type HFL (CHFL) inverter, a combined rectifier topology is deduced. To prevent a shorted circuit, two additional switches are used in the new topology. The operation mode of the CSR-HFL inverter is analyzed and the mathematical relationships are given. The difference and correlation, and advantages and disadvantages, are analyzed between the CSR-HFL inverter and the conventional HFL inverter. The relevant grid-connected inverter, ac/ac converter, and full-wave CSR-HFL inverter are also given. The experimental results verify that the proposed CSR-HFL inverter has excellent performance and high efficiency. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

The voltage range of a renewable energy source, such as the photovoltaic cell, is influenced by the environment, light, temperature, and so on. The power conditioning system should adapt to the wide input voltage and have buck–boost ability. Based on the structure of the “ac/ac unit,” this paper presents a novel active buck–boost inverter (ABI) topology suitable for wide-range input, which can realize buck–boost conversion in a quasi-single-stage inverter. The ac/ac unit composed of active switches is utilized to perform voltage boost without introducing additional passive elements, which is in favor to the system power density and efficiency. Operational analysis in buck and boost modes are presented, and the modulation strategy applied in the ABI is also developed. Simulation and experimental results are presented to verify the operational principle and its modulation strategy. [ABSTRACT FROM PUBLISHER]

High-boost dc-ac inverters are used in solar photovoltaic (PV), fuel cell, wind energy, and uninterruptible power supply systems. High step-up and step-down capabilities and shoot-through immunity are some of the desired properties of an inverter for a reliable, versatile, and low-distortion ac inversion. The recently developed Z-source inverter (ZSI) possesses these qualities. However, the realization of ZSI comes at a cost of higher passive component count as it needs two sets of passive filters. A switched boost inverter (SBI) has similar properties as ZSI, and it has one L\-C pair less compared to ZSI, but its gain is less than ZSI. This paper proposes the current-fed switched inverter (CFSI) which combines the high-gain property of ZSI and low passive component count of SBI. The proposed inverter uses only one L\-C filter and three switches apart from the inverter structure. The inverter topology is based on current-fed dc/dc topology. Steady-state analysis of the inverter is presented to establish the relation between the dc input and the ac output. A pulse width modulation (PWM) control strategy is devised for the proposed inverter. An experimental prototype is built to validate the proposed inverter circuit in both buck and boost modes of operation. A 353-V dc-link and a 127 V (rms) ac are obtained from a 35.3-V dc input to demonstrate the boost mode of operation. A 200-V dc-link and a 10.5-V (rms) ac are obtained from a 37.8-V dc input to verify the buck mode of operation of CFSI. [ABSTRACT FROM PUBLISHER]

Induction heating systems are the technology of choice in many industrial, domestic, and medical applications due to its high performance. The core component of such systems is the power supply, which is usually composed of a rectifier stage and a resonant inverter. In order to simplify and further optimize the performance of the power supply, a class-E direct ac–ac converter featuring multicycle modulations is proposed in this paper. The proposed converter is composed of two switching devices that enable the direct ac–ac conversion. Single- and multicycle operation modes have been analytically described to prove the benefits, in terms of peak voltage reduction and output power control capabilities. A prototype featuring SiC junction-gate field-effect transistor devices, which perfectly fit these applications, has been designed and built to prove the feasibility of the proposed converter. The experimental results match the analytical results and validate the benefits of this converter. [ABSTRACT FROM PUBLISHER]

The three-level neutral-point (NP)-clamped (3L-NPC) converter is a promising multilevel topology in the application of megawatt wind power generation systems. However, the growing requirements by grid codes may impose high stress and even give reliability problem to this converter topology. This paper investigates the loss and thermal performances of a 10-MW 3L-NPC wind power inverter undergoing low-voltage ride-through (LVRT) operation. A series of new space vector modulation methods is then proposed to relocate the thermal loading among the power switching devices. It is concluded that, with the proposed modulation methods, the thermal distribution in the 3L-NPC wind power inverter undergoing LVRT becomes more equal, and the junction temperature of the most stressed devices can be also relieved. Also, the control ability of the dc-bus NP potential, which is one of the crucial considerations for the 3L-NPC converter, is even more improved by the proposed modulation methods. [ABSTRACT FROM AUTHOR]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

This paper proposes a multiple-input versatile matrix converter (VMC) for integrating hybrid ac/dc energy resources and storages to the power grid. The VMC is developed from the traditional indirect matrix converter but operates in the reverse-boost mode rather than in the forward-buck mode. The reverse-boost mode is more relevant here since most renewable sources and energy storages have lower voltages than the grid. The eventual VMC developed uses an alternative nine-switch converter, rather than usual six-switch voltage-source converter, for providing six input terminals in total. One three-phase ac source and three dc sources, or other source combinations, can therefore be connected to the VMC. Powers from these sources are channeled to the three-phase utility grid through the VMC's current-source inverter. Their proper dispatches are guaranteed by the proposed control and modulation schemes, which also help maintain near-sinusoidal input and output current waveforms. Mathematical proofs, simulation, and experimental results have shown that the VMC can indeed operate as intended. [ABSTRACT FROM PUBLISHER]

In this paper, a kind of zero-crossing distortion (ZCD) generated in the grid-connected current of a single-phase grid-connected inverter with unipolar hysteresis current control is investigated. By establishing the mathematical model of the grid-connected inverter around the zero-crossing points (ZCPs), the reason for causing the current ZCD is presented. It is ascribed to the slope of the actual current less than that of the reference one around the ZCPs. The expressions of the critical phase angle (the starting point of the current ZCD) and the amplitude of the current distortion corresponding to the parameters of the inverter and connected utility grid are obtained, and the solution for the ZCD based on on-line leading phase angle compensation is proposed. Simulation and experimental results verify the accuracy and feasibility of the theoretical analysis and the proposed solution. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]