Search

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

Three-port converters with high voltage gain are desirable solutions for integrating renewable energy and energy storage devices into high voltage dc bus. A high gain three-port converter with soft switching is proposed in this paper, which can realize zero voltage switching for all switches and zero current switching for all diodes in various operating modes. Single coupled inductor is used to achieve high voltage gain and to reduce the voltage stress of switches so that switches with low on-resistance can be selected to reduce the conduction loss. In addition, the advantages of fewer components, higher voltage gain, and very low switch voltage stresses make the proposed converter more suitable for application in renewable energy systems than similar solutions. Various operating modes, performance analysis, design considerations, efficiency analysis, and control method of the proposed converter are discussed. A laboratory prototype with 30 V renewable energy source, 48 V energy storage device and 400 V output is designed to verify the performance of the proposed three-port converter. [ABSTRACT FROM AUTHOR]

This paper reports the application of silicon bipolar junction transistor (BJT) modeling techniques to the modeling of dynamic behavior of high-voltage 4H-SiC BJTs, and the experimental validation thereof. High-voltage silicon BJTs are impractical due to their low current gain that requires a bulky base driver. Emergence of high-voltage 4H-SiC vertical NPN BJTs with a tenfold higher gain enables the application of efficient drivers, with ratings close to those of IGBTs. This paper demonstrates the advantages offered by 4H-SiC BJTs by means of wide-scale measurements at 800 V and 10 A in a range of temperatures up to 175 °C and adjusted base driver switching rates. This paper shows that the turn-off storage delay in the SiC BJT is two orders of magnitude lower than that of the silicon device. It also shows that the turn-on switching transients of SiC device are by an order of magnitude and the turn-off transients are by two orders of magnitude faster than that of its silicon counterpart, resulting in a tenfold reduction of the switching energy. It also demonstrates the temperature dependence of switching transients of the silicon BJT, and the relative temperature-invariance of the SiC device's performance. This paper concludes with validation of the transient models for the 4H-SiC NPN BJT, showing that the model is sufficiently accurate for transient switching and loss calculations. [ABSTRACT FROM AUTHOR]

Partial discharge (PD) detection is a fundamental tool for the design and diagnosis of insulation systems, particularly organic materials that must operate throughout their life without PD. While the methods for PD measurements under sinusoidal supply voltage are well-established, the same does not hold under repetitive-pulse voltage waveforms, such as those provided by inverters. Electromagnetic noise generated by electronic switch commutation in inverters can overlap with PD pulses, making it difficult to measure, separate from noise, and identify PD. This is particularly more cumbersome when fast rise-time switches are employed. To address these issues, this paper investigates methods to detect PD pulses on enameled wires under repetitive impulsive voltages with different rise times of 60, 500, and 1000 ns, proposing techniques which allow separation of PD from noise even when they overlap in time and frequency domains. This paper employs a time-domain approach using standard deviation curve acquired from a set of measurements to discriminate PD from repetitive commutation disturbance. These techniques can be implemented to achieve unsupervised noise rejection, which would be an important goal for both offline and online PD testing. The proposed approach is validated successfully through tests carried out on a low-voltage motor. [ABSTRACT FROM AUTHOR]

DC shipboard power systems have been considered as a promising solution for stricter environmental regulations on ships due to their main benefits in fuel savings with variable speed engines and easy integration of energy storage systems. In order to employ the dc solution in the shipboard power systems, the dc power systems have to be protected from a system fault with protection selectivity to minimize impacts of the fault or to avoid other undesirable situations in the system. For low-voltage dc shipboard power systems, a three-level protection has been proposed: 1) fast action (first)—bus separation by solid-state dc bus-tie switch; 2) medium action (second)—feeder protection by high-speed fuse; and 3) slow action (third)—generator–rectifier fault controls. This paper proposes a new method by means of additional bus capacitance added in main dc buses to help reliable operation of the three-level protection. The principle of the proposed method is introduced and the sizing of the additional bus capacitance is addressed in this paper. With the modeling of the dc shipboard power systems, the analyses of voltage drops for the bus separation failure and fault clearing time for the feeder protection are carried out to verify the proposed method. The results show that the proposed method not only mitigates the voltage drop for the bus separation failure, but also achieves the selectivity and the sensitivity for the feeder protection. [ABSTRACT FROM AUTHOR]

The randomly switching communication topologies are of particular interest for researchers in the field of consensus control since the communication connection among multiple agents can randomly change with time and space. Following this pattern, this paper models the communication topology with the Markovian randomly switching graphs, since the Markovian chain process is usually used to model the network with Rayleigh fading channel. In this stochastic framework, this paper focuses on the consensus control and performance improvement problems of grouped agents with linear or linearized nominal dynamics. To solve this problem, a class of state-feedback controllers is proposed under the assumption that all the state measurements are available. These controllers are intrinsically distributed since they solely require the relative information between neighboring agents. Moreover, the notion of $\mathcal {H}_{\infty }$ ($\mathcal {H}_2$) stochastic consensus region integrated with transient performance is defined to measure the robustness of the proposed controllers with respect to the communication topologies. This paper theoretically shows that these controllers yield unbounded consensus region, which implies that they are well-designed. Furthermore, these controllers can improve the $\mathcal {H}_{\infty }$ , $\mathcal {H}_2$ consensus, and transient performances of agents subject to external and initial-state disturbances. At the end of this paper, numerical simulations and experiments are performed to verify the theoretical results. [ABSTRACT FROM AUTHOR]

The development of wide band-gap semiconductor devices is rapidly promoting the development of power electronics technology, especially in high frequency (HF) power converter region. A category of HF power converter is switch-mode power amplifier (PA). This paper focuses on the implementation of a multiphase dc–dc PA with high bandwidth and high power rate. When naturally sampled phase-shifted carrier modulation is implemented in the practical digital control system to control this HF power converter, the pulsewidth error problem caused by limited domain frequency of control chip becomes much severer. As a result, dc voltage component of each phase becomes different under several conditions, leading to current imbalance among phase inductors. This paper analyzes this problem and proposes a sensorless control method to solve it, based on the injection of random sequence in reference wave. A four-phase prototype employing GaN devices is fabricated, switching at 1 MHz. Current imbalance and effectiveness of the proposed control method are verified by experimental results. The prototype is capable of uniformly amplifying sine signal within 200 kHz and a 350 kHz bandwidth random signal, with peak output power up to 810 W. [ABSTRACT FROM AUTHOR]

This paper presents an optimization method for selective harmonic elimination in a cascaded multilevel inverter using teaching–learning-based optimization (TLBO). The main objective in selective harmonic elimination (SHE) strategy is to eliminate low-order harmonics by solving nonlinear equations and reaching optimal solution, while the fundamental component is satisfied. In this paper, in one side, the influence of optimal dc sources is investigated to reach the SHE goal, and in another side, comparing optimization methods is considered. In this paper, the TLBO as a recently emerged nature-inspired algorithm is presented to provide better results for the SHE in comparison with genetic algorithm, artificial bee colony, imperialistic competitive algorithm, harmony search, ant colony optimization, particle swarm optimization, and differential evolution. For better comparison of those methods and influence of optimal dc sources, 5-, 9-, and 15-level inverters are chosen and MATLAB software is used for optimization. Simulation results show the superiority of TLBO, higher precision and probability of convergence than other mentioned algorithms. Finally, to validate the influence of optimal dc sources and the accuracy of TLBO results, the experimental setup is conducted for a 5-level cascaded H-bridge inverter with optimal dc sources. [ABSTRACT FROM AUTHOR]

Satellite dc–dc power converters are required to have electromagnetic interference (EMI) compatibility as well as high reliability. The requirement of high reliability limits the complexity of the structure as well as the number of low-reliability components. In this paper, a conventional active-clamp-forward (ACF) topology is examined for a satellite converter owing to its relatively simple structure, small number of components, and good clamping capability regarding its switch voltage stress. However, it has a pulsating input current shape, a high di/dt level, and high switch voltage stress, which are disadvantageous with regard to the EMI filter size and high-input-voltage converter applications. To overcome these drawbacks, a new ACF topology with a continuous input current waveform is proposed. In the proposed waveform, the voltage stresses on the main switches are relieved, which is crucial to ensure the reliability of satellite FET switches, by utilizing a two-series connected structure. These features allow the proposed converter to serve as a high-input-voltage, high power-density satellite converter. In this paper, 100 W prototype converters with 50 V inputs operating at 300 kHz are built with a high power density of 47.9 W/in3. Experiments on these prototype converters are carried out to verify the features. [ABSTRACT FROM AUTHOR]

This paper presents a 5-level inverter topology for open-end induction motor drives by using a single dc source. The open stator windings of the drive are supplied with a 3-level flying capacitor inverter from one end and capacitor-fed 2-level inverter from another end. The voltage ratio of the dc link to the capacitor in 2-level inverter is maintained at 4:1 ratio to generate five-level voltage output. The capacitor in 2-level inverter is balanced by the switching redundant vector combinations from both the inverters while the floating capacitors in the 3-level inverter are balanced by using redundant switching states. The proposed topology gives 5-level operation with less number of floating capacitors and power semiconductor switches compared to other existing topologies. Also, the balancing of the capacitors is independent of load power factor and modulation index. Further, the generalization of the proposed dual inverter scheme for any n-level inverter is also included in this paper. The experimental results and required analysis are also presented to validate the inverter scheme. [ABSTRACT FROM AUTHOR]

Active magnetic bearing is a core technology for high-speed rotational machines. Power electronics converter as the active magnetic bearing drive is the actuation unit and its topology highly impacts the performance of the bearing system. This paper introduces the progress of topology of active magnetic bearing drive. The initial topology of an H-bridge does not sufficiently utilize the power electronics devices. The topology with half-bridge and shared phase-leg has been proposed as the fundamental topology. In this paper, two approaches of novel magnetic bearing drive topology modification have been developed on the basis of the fundamental topology. In the first approach, central phase-leg for multiaxis magnetic bearing drive can be further shared and the power electronic devices can be globally optimized in the whole system. Further, a topology with current in the reverse direction can reduce the central phase-leg current rating and power losses. In the second approach, fault-tolerant magnetic bearing drive topology has been developed on the basis of the fundamental topology, too. It can ride-through the open-circuit fault of power electronics switch-in operation and keep levitation for the magnetic bearing. The series work of novel topologies can improve the performance of an active magnetic bearing system in application. [ABSTRACT FROM AUTHOR]

This paper presents the development of a Class-D full-bridge zero-voltage switching (ZVS) inverter, applicable to wireless power transfer (WPT) systems, operating at 13.56 MHz switching frequency with dynamic dead-time control (DDTC). Resonant-coupled WPT systems are being designed at ultrahigh switching frequencies to reduce the size of the wireless link and the passive components. Maintaining ZVS while controlling the output power delivered to a fixed or variable load is one of the major challenges of designing inverters at multi-MHz switching frequencies. DDTC is the approach deployed in this paper to sustain soft switching of a Class-D full-bridge inverter over the full range of output power while regulating the input dc bus voltage. Simulation results are presented to show that dynamically controlling the dead-time during input dc bus voltage variations reduces switch-node voltage overshoot, prevents large current spikes in the switching devices, and reduces associated high switching loss. Practical results obtained show that DDTC reduces switch-node voltage overshoot, increases the inverter efficiency, and reduces the steady-state temperature of the inverter during output power regulation. [ABSTRACT FROM AUTHOR]

Compared with the conventional two-level dual-active-bridge (DAB) dc–dc converter, the three-level DAB converter could operate with lower voltage rated switching devices and provide more control degrees of freedom, which enhances the control flexibility. This paper proposes a modulation strategy with five control degrees of freedom. In the previous work with multiple control degrees, the optimization strategies for efficiency or inductor current minimization are investigated; however, these strategies all need detailed mode analysis and complex mathematical optimization tools to obtain the optimal duty cycles. In this paper, an optimization strategy for the root-mean-square value of the inductor current is proposed. This method extracts the fundamental and third-harmonic components from the high-frequency voltages on both sides and adjusts the amplitude of the bridge voltages by the vector diagram to obtain the optimal duty cycles. The inductor current can be reduced significantly at light loads with the proposed strategy, so the efficiency of the converter can be improved. Moreover, the optimization process does not need the detailed operation analysis of the converter, nor does it require the complex mathematical optimization tools. Finally, the performance of the three-level DAB and the optimization strategy are verified by the experimental results. [ABSTRACT FROM AUTHOR]

In this paper, a new modular and active snubber cell, easily applicable, and attractive for converters, especially have many switches proposed. This snubber cell is implemented on the single phase of a grid-connected three-phase T-type three-level inverter (T-3LI). In this new converter, the main switches turn-on under zero-voltage transition and turn-off under zero-voltage switching (ZVS). Also, auxiliary switches turn-on under zero-current switching and turn-off under ZVS. All snubber diodes operate under soft switching (SS). There are no additional current and voltage stresses on the main switches. During an SS operation, the switching energies are transferred to a dc voltage source. Then, these energies are processed to input with an independent dc–dc converter. Thus, all switching energies are recycled. In this paper, the principle operation and steady-state analysis of the modular and active snubber cell for a single-phase T-3LI are presented and experimental results, rated 1 kW and 100 kHz, are provided to verify theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, we propose adaptive algorithms of gain tuning for Kalman filters and switching Kalman and $\mathcal {H}_{\infty }$ filters for discrete systems. Both of the gain tuning and switching rely on square means of innovations. This paper also provides stability analyses on time-varying Kalman filters and derives a sufficient condition for their asymptotic stability, on which our gain-tuning algorithm is based. It should be noted that the stability condition is available for even nonstabilizable systems having their uncontrollable poles on the unit circle. To illustrate those algorithms, we perform simulations using a harmonic oscillator model that is nonstabilizable and has its poles on the unit circle. Furthermore, we apply the algorithms to estimation of a ship's oscillation, particularly, with time-varying frequencies by simulations and model experiments. Consequently, all the results of stability analyses, simulations, and experiments have convinced that the algorithms are solid and effective. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

Solid state transformer (SST) integrated hybrid dc–ac microgrid (HMG) has wide operating capabilities in presence of dc–ac loads, renewable energy resources, and energy storage. This paper proposes control strategies for localized control of zonal hybrid microgrid, enabled by the SST and centralized energy storage devices (ESD) integrated using dual active bridge (DAB) converter. The control of DAB dc–dc converter is modified for zero circulating power flow (ZCPF) operation in both SST and ESD. Power management and coordination control used in this paper ensures the power supply reliability of the zonal HMG integrated through the SST. Microgrid system, along with its proposed controllers, provides a stabilized low-voltage dc and ac network ports, in both grid feeding and forming modes. The performance of the configured HMG system is evaluated under various power management scenarios using the MATLAB software platform. Further, the SST architecture, with its proposed controller, is tested on FPGA-based hardware platform. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a single-inductor dual-output (SIDO) dc–dc converter is proposed. The significant feature of the proposed converter is feeding a constant power load in low-voltage side (LVS) port, where even feeding a variable load at LVS does not have any cross regulation to high-voltage side port with the desired approximation. Magnificently, both merits are obtained in open-loop manner, which is an outstanding characteristic in comparison with that of the existed converters. In this paper, soft commutation and soft switching of switches and diodes are investigated along with the aforementioned main novelty. Moreover, detailed theoretical analyses of the proposed SIDO dc–dc converter in continuous conduction mode are presented besides the comparisons with some other structures. Finally, theoretical analyses are verified through a 1500 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

This paper presents a novel insulated gate bipolar transistor (IGBT) behavioral model on the field programmable gate array (FPGA), which is suitable for the real-time simulation of fast transients in power electronics circuits. In this model, the static and dynamic behaviors of the IGBT switch are described and modeled separately. The static IGBT model is represented by the saturation region of output characteristic and is a part of the circuit network model. The dynamic IGBT model is combined with the static one to describe the fast switching transient behaviors by using the IGBT equivalent circuit model. The presented dynamic model in this paper does not involve any iterative solving algorithm and can be designed with highly pipelined structures on FPGA. Therefore, the IGBT switching transient waveforms can be generated precisely with a 5 ns resolution. The proposed model is tested with two cases—a four-phase floating interleaved boost converter and a three-phase five-level modular multilevel converter. The effectiveness and accuracy of the model are validated by comparing the real-time simulation results with offline simulation software. [ABSTRACT FROM AUTHOR]

This paper proposes a capacitor voltage regulation method for the dual converter with a floating bridge for aerospace applications. This topology has previously been reported, but with a constrained voltage utilization factor due to the need for capacitor voltage regulations. In this paper, the effect of switching states on the voltage variation of capacitor is quantitatively modeled and an enhanced space vector modulation scheme with current feedback is proposed to achieve an active control of the floating capacitor voltages. This proposed method also allows further exploitation and utilization of converter voltage. The relationship between the allowed modulation index of dual converter and load power factor is obtained and expressed using a fitted polynomial equation. The advantages of the proposed method include boosted voltage utilization and superior performance in term of capacitor voltage balance. These advantages have been proven through simulation and experimental results on RL loads as well as with an open-end winding induction motor. The proposed modulation scheme can boost the converter voltage utilization by at least 10% while achieving full four-level operation. More importantly, the higher available voltage allows extending the constant torque region of the motor, the further beginning of field weakening operation could be postponed. [ABSTRACT FROM AUTHOR]

This paper proposes a visible light communication (VLC) system consisting of a single-stage buck–boost power factor correction converter operating in the discontinuous conduction mode with dimming capability. Additionally, this paper proposes the on–off M-frequency shift keying modulation for the VLC system. This modulation allows for the transmission of more than a single bit for each switching period without affecting the dimming characteristics of the light-emitting diode luminaire. The design of the whole system is discussed in detail, including both transmitter and receiver modules. A 20-W laboratory prototype was built in order to verify the proposed modulation scheme. The experimental evaluation showed a good performance of the transmitter, which was able to perform simultaneously the desired functions, namely power factor correction, dimming, and data transmission. The receiver also achieved the desired performance with a low bit error rate (BER). The results showed that the proposed system was able to transfer data between emitter and receiver with a bit rate of 1.11 Mb/s at a frequency of up to 375 kHz over a distance of 10 m, and with a BER lower than $10^{-3}$ under the influence of external lighting sources with illuminance levels up to 500 lx. [ABSTRACT FROM AUTHOR]

The extra-LC auxiliary-resonant-snubber-based converter (ELCARSC), as a soft-switching converter, has the advantages of low switching loss, low electromagnetic interference noise, and low-output distortion caused by the dead-time effect. However, the dead-time effect is still the main problem in a high-precision application. Besides, the traditional control and compensation methods rely on the accuracy of the circuit parameters, especially the junction capacitance, thus resulting in compensation error. Therefore, this paper proposed a novel high-precision control method through modulating the initial resonant current to eliminate the dead-time effect of ELCARSC. The method does not need complicated online calculation and reduces the dependence on the accuracy of the circuit parameters, especially the influence of the junction capacitances of the switches. In this paper, the dead-time effect of the ELCARSC is analyzed. The output voltage error with the conventional variable-timing control method is analyzed. Subsequently, the proposed modulated initial resonant current control is introduced. Finally, a prototype was developed that verified the effectiveness of the control method. The quality of the output current and voltage is improved by utilizing the proposed control method. However, the peak current of the auxiliary switch is increased. [ABSTRACT FROM AUTHOR]

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper presents research results of voltage gain number control methods of a power electronic resonant zero-current switching dc–dc switched-capacitor (SC) voltage multiplier (SCVM) in a topology with fault tolerance capability (FSCVM). The converters operated under the basic switching patterns are constant-voltage-gain dc–dc series-parallel resonant SC converters. However, this paper presents a method for the output voltage regulation by a special switching strategy. A variable voltage gain is made possible by selecting the number of active switching cells, using an appropriate control method. This creates a set of voltage ratio ranges. In addition, the proposed topology and method of control enable a fault-tolerant operation of the FSCVM under various failures of the device. The paper presents an analysis of the concept, simulation results and an experimental verification in a three-cell FSCVM dc–dc resonant boost converter operating at a 200-watt charge. Issues regarding the selection of components related to the problem of inrush currents that can occur during the voltage ratio increase are also analyzed in this paper, and the design for low inrush currents is demonstrated. [ABSTRACT FROM AUTHOR]

This paper presents an average dwell-time method for fault-tolerant control of a class of uncertain switched linear time-delay systems and also designs an algorithm to determine the parameters pertaining to the dwell-time condition. Compared to the literature results, this paper features the following: 1) the proposed method is independent of switching polices if switchings are slow enough in the average sense; 2) the proposed control design guarantees exponential stabilization of this class of time-delay linear systems with actuator faults; and 3) this method treats all actuators in a unified manner without a need to identify which are faulty or healthy actuators. The proposed method is applied to the water pollution control problem, for the first time, to deal with different ratios of stream flow rates to effluent flow rates. [ABSTRACT FROM AUTHOR]

This paper proposes a new developed switched-capacitor converter to achieve high-voltage pulses with adjustable voltage level and frequency. The proposed topology generates repetitive high-voltage pulses by using low-voltage power supply with reduced number of components, including power semiconductors and capacitor. Therefore, a converter based on switched-capacitor units with high voltage gain and high efficiency can be achieved. Operation principles and design steps of the converter as well as comparative study with conventional converters are described in this paper. Finally, simulation and experimental results of a two-stage structure of the proposed circuit validate the operation principles and features of this topology. [ABSTRACT FROM AUTHOR]

This paper develops a modulation based fault-tolerant (FT) strategy for restoring the operation of three-phase modular multilevel converters (MMCs) with faulty switches. This FT strategy is based on a proposed modified space vector modulation (SVM) technique that generates balanced line-to-line (line) voltages even in the case of a fault occurrence. In the postfault operation, the proposed strategy is able to restore the fundamental amplitude of the line to the neutral (load) voltages to that of the normal operation condition with a slightly increased voltage stress over the switches in the faulty phase. In this paper, first a brief background about MMCs and SVM technique is provided. Then, the proposed FT strategy and the modified SVM technique are presented. Finally, several simulation and experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

Standard pulsewidth modulation (PWM) schemes for modular multilevel converters (MMC) have neglected deviations of the module voltages from the mean module voltage of an MMC arm as well as the dynamic change in the module voltages since their last measurement and during the switching period. This induces an output voltage error. Large output voltage errors disturb the higher level closed-loop control of the MMC, such that control targets cannot be met anymore. The output voltage error can be reduced using advanced PWM methods that predict and include the dynamic change of the individual module voltages during a switching period in the calculations for the duty cycle. This paper shows measurement results obtained from an experimental medium-voltage prototype, proving that advanced methods lead to much lower output voltage errors than the standard methods, but cannot fulfill the expectations raised by the simulations documented in the literature. In order to overcome the limitations of the old method, a new method that includes the semiconductor voltage drop and parasitic resistances is introduced and evaluated with measurements in this paper. Furthermore, simulation results showing the influence of the considered modulation methods on the closed-loop current control performance are presented. [ABSTRACT FROM AUTHOR]

This paper presents two capacitor voltage balancing (CVB) strategies for modular multilevel converter (MMC) applications. Both balancing schemes are based on model predictive control and are designed to efficiently solve a constrained optimal control problem, where the predicted capacitor voltage errors are included in the cost function with the demanded output voltage of a cluster being forced through an equality constraint. The first method proposed in this paper computes specific modulation indexes for each module using the explicit solution of a relaxed version of the original optimization problem. The second approach proposed in this paper reduces the complexity of the original problem by linearizing the objective function and using an optimal sorting network based on a greedy algorithm to solve this approximation. Considering the structures of both solution approaches, they are integrated into modulation schemes based on phase-shifted and level-shifted pulsewidth modulation algorithms, respectively. Experimental results obtained from a nine-cell single-phase MMC prototype demonstrate the good performance achieved with the proposed methodologies, as well as the implementation simplicity offered by the proposed CVB algorithms. [ABSTRACT FROM AUTHOR]

Induction motor drives operated with a low ratio of the switching frequency to the fundamental frequency (i.e., pulse number) are prone to have high magnitudes of low-order torque harmonics. This paper proposes a method to analytically evaluate the harmonic torque spectrum based on the pulsewidth-modulated voltage waveforms for low pulse number operation. The predicted torque harmonic spectra for different pulsewidth-modulated waveforms are validated through simulations and experiments. This paper also reports optimal switching angles to minimize the total rms value of torque harmonics of order 6, 12, 18 $,\dots,$ $6(N-1)$ , considering the number of switching angles per quarter ($N$) to be 4 and 5. Compared to sine triangle pulsewidth modulation and selective harmonic elimination pulsewidth modulation with the same pulse number, the proposed optimal switching angles significantly reduce the total rms value of all harmonic torques of order lower than $6N$. Extensive simulation and experimental results on a 3.7-kW induction motor drive are presented to demonstrate the superior performance of the proposed optimal pulsewidth modulation. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-down dc–dc converter with ultrahigh step-down conversion ratio is proposed. Advantages of the proposed converter are high step-down ratio, extended duty cycle, reduced switching losses by a converter operation under zero-voltage switching (ZVS) conditions, reduced reverse reco-very losses of diodes by achieved zero-current switching turn-off condition, and reduced voltage spikes by the inherent active-clamping structure of the converter. In this converter, series capacitors and coupled inductors have been used in power path to achieve the low voltage gain and extended duty cycle. By the inherent active-clamping structure of the proposed converter, the leakage inductance energy is totally recovered in the output; therefore, the high voltage spike across the semiconductor devices is suppressed. The switches of the proposed converter can operate under ZVS conditions, which cause reduced switching losses and improved efficiency. In this paper, the converter operating modes are discussed, and a prototype circuit is implemented. Experimental results are presented to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

Soft-switching techniques of transformerless photovoltaic grid-connected inverters (TLIs) can significantly reduce switching losses, as well as soften switching processes. Conventional dc–ac soft-switching configurations proposed by Dr. Deepakraj M. Divan are invalid in TLIs because of the leakage current problem. In order to develop soft-switching techniques in TLIs, this paper proposes a new soft-switching configuration and a procedure to guide the invention of soft-switching TLIs. First, this paper proposes two basic resonance tanks related to dc bus polarities, and then, uses these basic tanks to elevate four popular full-bridge-type TLIs according to the proposed guideline. As a result, four soft-switching TLIs are gained. Second, this paper picks obtained soft-switching highly efficient and reliable inverter concept (HERIC) as example to analyze its soft-switching operation principle and performance. As a consequence, all active switches of the gained soft-switching HERIC circuit are switched under both of zero-current turn-on and turn-off conditions; the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off of diodes; meanwhile, the common-mode voltage at the switching frequency scale is still constant. Finally, some experimental results from a 3-kW universal prototype at 50-kHz switching frequency are provided to verify the effectiveness of the main contributions of this paper. [ABSTRACT FROM AUTHOR]

The paper deals with some new results on the averaging theory approach for the analysis of feedback controlled pulsewidth modulation power electronic converters. It develops some considerations regarding the averaging approximation of time-variant differential systems proving an analytical relationship between the accuracy with which the solution of the averaged model converges to the solution of the original time-variant model (i.e., the switched model) and the switching frequency of the converters. This relation is valid both for stable and unstable systems. Moreover, this paper confirms, as corollary, that under suitable conditions (verified during the standard operations of the power electronic converters) the averaged model uniformly converges to the switched model. [ABSTRACT FROM AUTHOR]

This paper proposes a novel control method for an asymmetrical-cascaded-multilevel-converter-based hybrid energy storage system (HESS), which includes one battery and several electrical double-layer capacitors (EDLCs). Traditionally, it is challenging to control the power distribution between different cascaded H-bridges by using different energy storage components as dc sources. In this paper, a feedforward space-vector-modulation (FFSVM) technique is used to distribute the active power between the battery and EDLCs. With the proposed voltage feedforward mechanism, the HESS can flexibly operate in the normal operation mode, the high-power output mode, and the reverse power absorption mode. The principle and effectiveness of the improved FFSVM technique are analyzed. Meanwhile, the state-of-charge-balancing mechanisms are introduced. The simulation results obtained in MATLAB/Simulink as well as the experimental results of a hybrid energy storage test bed based on the proposed system are presented to verify its performance. [ABSTRACT FROM PUBLISHER]

This paper presents a uniform control strategy for the bidirectional ac/dc interlinking converter (BIC) in hierarchical controlled hybrid microgrid. The uniform control strategy unifies different control structures for multifunctional BIC in terms of power management, ac and dc voltage support. With the unified control structure, various triggering mechanisms for BIC mode-switch are not compulsory in response to the relevant scenario changes in the power network. Therefore, the negative consequences, such as unsmooth transition and system collapse due to the inaccurate or slower mode switch, can be avoided. Moreover, the uniform control strategy is also applicable for the hierarchical controlled hybrid microgrid, whose control architecture is typically comprised of the centralized and decentralized levels. This enables the communication fault ride-through capability and the impact from the communication failures can thus be mitigated. To sum up the above two features, the proposed control strategy is able to provide a smooth operation for the BIC without control mode switch in the event of unintentional scenario changes in power or communication network. To verify the validity of the proposed uniform control strategy, the controller hardware-in-the-loop experimental results have been provided in this paper. [ABSTRACT FROM PUBLISHER]

This paper presents an improved saliency-based position sensorless drive of an interior permanent-magnet synchronous machine (IPMSM) with a single current sensor, used for low cost applications. The phase current, reconstructed from a dc-link current, shows a reconstruction error resulted from the difference of the sampling point from that of a full current sensor drive. This reconstruction error results in degradation of the overall sensorless control performance. In this paper, we analyze the impact of the reconstruction error depending on the injection frequency for a high frequency voltage signal injection sensorless control. Based on this analysis, we propose an improved position sensorless drive that employs a new current reconstruction method. In order to minimize the reconstruction error, the proposed current reconstruction method predicts the dq-axis currents with the same sampling point as a full current sensor drive. Several experimental results are provided to verify the analysis of the reconstruction error and the proposed method's improved sensorless control performances. [ABSTRACT FROM PUBLISHER]

This paper develops a novel voltage equalizer by combining wireless power transfer (WPT) and a voltage multiplier (VM) for series-connected energy storage cells. The physical isolation achieved by WPT can offer several unique benefits that traditional equalizers can hardly provide. In this paper, the characteristics of a multiple-output VM are analytically discussed and used to develop an equivalent one-output VM model. Based on this model, parameters of the WPT system are properly designed. The proposed design methodology can achieve a single-switch voltage equalizer without feedback control, which dramatically decreases the circuit complexity and cost. Moreover, this methodology can naturally ensure a robust system under small coil misalignment. In the experiment, the proposed system is built to balance four series-connected ultracapacitor modules. The system efficiency is 72.8% at a load power level of 10 W. [ABSTRACT FROM PUBLISHER]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel fuzzified mechanical sensorless speed estimation technique for permanent magnet direct current (PMDC) brushed motor operated with pulse width modulation (PWM) based terminal voltage. For replacement of conventional mechanical speed sensors, few mechanical sensorless speed estimation techniques have been reported recently in the field of PMDC brushed motor. In this paper, a novel technique is applied over a recently reported semianalytical dynamic time-domain PMDC brushed motor model incorporating space-domain effects, namely slotting effect and commutation phenomenon to simulate the proposed estimation process. Ripple and back electromotive force based standalone estimation approaches are hybridized in order to eliminate uncertainties in all regions of estimation. In this paper, a discrete fuzzified hybrid speed estimation model has been proposed with adequate dynamic simulation responses. Further the proposed discrete speed estimation model has been applied experimentally over a PWM-driven 24-V, 12-teeth, 100-W PMDC brushed motor and various dynamic real-time responses have been compared with conventionally captured speed samples to validate the proposed model. [ABSTRACT FROM PUBLISHER]

High-frequency components of acoustic noise radiated by the electric powertrain make the subjective perception of electric vehicles worse than expected under certain operating conditions. In order to investigate the influence of acoustic components on sound quality, a pulse width modulation (PWM)-fed electric powertrain is studied in this paper. First, the acoustic noise of the electric powertrain is collected in a semianechoic chamber. Then, two types of acoustic components of the electric powertrain, namely harmonic order noise and switching noise, are distinguished through the analyses of supplied current from the inverter and gear vibration. Furthermore, the relationship between subjective perception and spectral characteristics of the noise is discussed, based on which sensitivity is established. Subsequently, the contributions of acoustic components to psychoacoustical parameters are determined. After that, a sound quality model of the acoustic noise radiated by the electric powertrain is established. The comparison between jury test and prediction shows that the established model can be used for sound quality evaluation of the electric powertrain. Finally, the influences of harmonic order noise and switching noise on subjective perception are discussed. The main original contribution of this paper concerns the influences of harmonic order noise and switching noise radiated by PWM-fed electric powertrain on sound quality. [ABSTRACT FROM PUBLISHER]

This paper presents a new multilevel converter topology based on a variable or multilevel dc-link stage. This stage is shared by all inverter output phases, thus increasing the number of output voltage levels while reducing the overall number of active devices compared to traditional topologies; therefore, it is called a reduced multilevel converter (RMC). The converter is not capable of reducing the blocking voltage of the devices; hence, unlike other multilevel converters aimed at medium-voltage applications, this converter is interesting for low-voltage- and high-power-quality-demanding applications such as photovoltaic inverters, wind energy conversion systems, and uninterruptible power supplies. The main novelty behind the proposed concept is the basic dc cell used to generate the variable dc-link voltage, which includes a controlled path through the floating capacitors to provide the necessary degree of control to enable a shared multilevel dc link for all the output phases of the converter. The dc cells are connected in a multicell structure to increase the number of levels of the converter. A five-level version of the RMC topology is briefly compared to other five-level converters such as the five-level active neutral-point-clamped converter and the five-level flying capacitor converter. This paper presents the structure of the new topology with its operating principle, switching states, main characteristics, and experimental validation using finite-control-set model-predictive control. [ABSTRACT FROM PUBLISHER]

A new isolated single-stage soft-switching power-factor-correction (S4 PFC) driver for supplying light-emitting diodes (LEDs) is introduced in this paper. In the proposed LED driver, the switches voltage stress and also the dc-bus voltage is limited to the peak of the line voltage. Hence, low voltage rated mosfets and diodes can be used. The efficiency is improved because the switches are turned on under zero current switching (ZCS) condition and turned off under zero voltage zero current switching (ZVZCS) condition. Also, no current feedback is required since the converter provides an output current independent of output voltage. In this paper, operating principle of the proposed LED driver is presented and design considerations are discussed. To verify the theoretical analysis, a laboratory prototype of the proposed converter for supplying a 50 W/70 V LED module from 220 Vrms/50 Hz ac mains is implemented, and the experimental results are presented. Since current feedback is not used, dimming property and operation for universal voltage range is not achievable. [ABSTRACT FROM PUBLISHER]