Search

This paper presents the development of a Class-D full-bridge zero-voltage switching (ZVS) inverter, applicable to wireless power transfer (WPT) systems, operating at 13.56 MHz switching frequency with dynamic dead-time control (DDTC). Resonant-coupled WPT systems are being designed at ultrahigh switching frequencies to reduce the size of the wireless link and the passive components. Maintaining ZVS while controlling the output power delivered to a fixed or variable load is one of the major challenges of designing inverters at multi-MHz switching frequencies. DDTC is the approach deployed in this paper to sustain soft switching of a Class-D full-bridge inverter over the full range of output power while regulating the input dc bus voltage. Simulation results are presented to show that dynamically controlling the dead-time during input dc bus voltage variations reduces switch-node voltage overshoot, prevents large current spikes in the switching devices, and reduces associated high switching loss. Practical results obtained show that DDTC reduces switch-node voltage overshoot, increases the inverter efficiency, and reduces the steady-state temperature of the inverter during output power regulation. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

Soft-switching techniques of transformerless photovoltaic grid-connected inverters (TLIs) can significantly reduce switching losses, as well as soften switching processes. Conventional dc–ac soft-switching configurations proposed by Dr. Deepakraj M. Divan are invalid in TLIs because of the leakage current problem. In order to develop soft-switching techniques in TLIs, this paper proposes a new soft-switching configuration and a procedure to guide the invention of soft-switching TLIs. First, this paper proposes two basic resonance tanks related to dc bus polarities, and then, uses these basic tanks to elevate four popular full-bridge-type TLIs according to the proposed guideline. As a result, four soft-switching TLIs are gained. Second, this paper picks obtained soft-switching highly efficient and reliable inverter concept (HERIC) as example to analyze its soft-switching operation principle and performance. As a consequence, all active switches of the gained soft-switching HERIC circuit are switched under both of zero-current turn-on and turn-off conditions; the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off of diodes; meanwhile, the common-mode voltage at the switching frequency scale is still constant. Finally, some experimental results from a 3-kW universal prototype at 50-kHz switching frequency are provided to verify the effectiveness of the main contributions of this paper. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

A novel hybrid pulse width modulation (PWM) technique is proposed in this paper for two parallel interleaved, two-level, three-phase voltage source inverters (VSIs). The two parallel interleaved VSIs are analyzed as a three-level (3L) inverter. A 3L inverter provides minimum line current ripple when nearest three voltage vectors are applied. In this paper, a novel carrier-based PWM technique is developed that ensures the application of nearest voltage vectors, keeping average circulating current to zero over a switching period. For carrier-based implementation of the proposed PWM, generalized common-mode (CM) offsets are derived in terms of maximum and minimum values of reference signals. Each 3L space-vector sector is divided into seven subsectors. For each subsector, a CM offset is calculated, addition of which to reference signals ensures the minimum line current ripple and zero average circulating current. Simulation and experimental results are provided to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

This paper investigates and evaluates the performance of a single-phase split-source inverter (SSI), where an alternative unidirectional dc–ac configuration is used. Such configuration is utilized in order to use two common-cathode diodes in a single device instead of using two separate diodes, resulting in minimum parasitic inductance in the commutation paths. In this paper, the analysis and modulation of the single-phase SSI using this alternative configuration is discussed, and the analysis of the low-frequency component in the dc side is introduced. Moreover, the features behind employing the triangular, the trailing-edge sawtooth, and the leading-edge sawtooth carriers with the single-phase SSI are discussed, and the differences among these carriers are highlighted. In order to highlight the performance of the proposed SSI, a comparative study is conducted with the two-stage architecture and the single-phase quasi-Z-source inverter (qZSI). The introduced analysis is enhanced with simulation results using MATLAB/PLECS models, where a 1-kVA single-phase SSI is designed and simulated. Finally, the designed 1-kVA single-phase SSI is implemented experimentally and tested at different operating points, i.e., at different voltage gains, and a maximum efficiency of $95.5\%$ is obtained. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes the use of advanced bus clamping switching sequences to reduce the impedance network inductor current ripple of the three-phase Z-source inverter (ZSI). Proposed technique is named as ABC4_MCB. MCB denotes that the maximum constant boost control method is used for the voltage boosting. One of the conventional space vector pulsewidth modulation of ZSI, “ZSVM6,” is termed as ZSVM6_MCB under the maximum constant boost control method. The switching sequences of ABC4_MCB technique are designed in such a way that it offers around 34% reduction in the maximum instantaneous inductor current ripple as compared to the ZSVM6_MCB for the equal average switching frequency. The factor of percentage reduction in the inductor current ripple using the proposed technique is constant over the entire range of shoot through duty ratio (0–0.48). Theoretical findings have been verified using simulation and experimental results. [ABSTRACT FROM AUTHOR]

In recent years, a number of bidirectional inductive power transfer systems (BD-IPT) suitable for wireless grid integration of electric vehicles have been developed. These developments have been fueled by the enhanced efficiency and spatial tolerance offered by BD-IPT systems. A typical BD-IPT system utilizes two synchronized full-bridge converters operating at fixed duty cycles to drive the primary and secondary magnetic couplers. However, in order to cater for a wide range of loading conditions, additional circuitry is employed at the expense of cost and power density. As an alternative solution, this paper proposes a novel power converter, named a boost active bridge (BAB), to replace the full-bridge converters. The BAB topology caters to a wide range of loading conditions without the need for any extra switching devices. A comprehensive mathematical model that predicts steady-state currents, voltages, and power transfer is presented to highlight the operating principles of the BAB technology. Experimental results obtained from a 3.5-kW prototype show a nearly constant efficiency under all loading conditions, validating the viability of the proposed BAB topology. [ABSTRACT FROM AUTHOR]

The magnetic resonant wireless power transfer (WPT) system with a class E inverter has wide application in mid-range power transmission, especially for several megahertz scenario. However, it is cumbersome for the existing modeling and analysis methods to obtain the analytical solution to the system variables, which limits the evaluation of system characteristic. This paper proposes a nonlinear mathematical model for the WPT system with a class E inverter. The equivalent small parameter method (ESPM) is first adopted to solve the proposed six-order nonlinear model, and symbolic-form steady-state periodic solutions are yielded. During the whole solving process, only three iteration steps are needed for the proposed method. Compared with other existing modeling and analysis methods, the symbolic periodic results acquired by the ESPM exhibit sufficient accuracy by virtue of the combination of more higher harmonics. Meanwhile, the calculation complexity is simplified remarkably. Simulation and available experiments validate the effectiveness and accuracy of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

Two parallel interleaved two-level (2L) three-phase voltage source inverters (VSIs) can be analyzed as a single three-level (3L) VSI. A generalized carrier-based method is proposed in this paper for implementing different 3L pulsewidth modulation (PWM) techniques using two parallel interleaved 2L VSIs. The proposed method modifies the given three-phase reference signals of 3L VSI for implementation of the PWM technique using two parallel interleaved 2L VSIs. The influence of nonidealities on the equivalent 3L PWM switching sequences is also discussed. To overcome the effect of nonidealities, a new modified discontinuous PWM technique (MDPWM1) is proposed. The analysis of different performance indices is carried out for different 3L PWM techniques, and the key advantages of different PWM techniques are identified. Simulation and experimental results are also presented. [ABSTRACT FROM AUTHOR]

The development of a photovoltaic ac module composed of a high static gain nonisolated dc–dc converter with current source output characteristic followed by an unfolding low-frequency inverter is presented in this paper. The operation of the dc–dc converter with high static gain and with reduced switch voltage is obtained using the Cuk converter integrated with the switched-inductor technique. The nonisolated structure allows the elimination of the volume and losses of the power transformer and leakage inductance, and an output filter configuration is proposed to reduce the high-frequency ground leakage current. The grid-tied inverter operating in a discontinuous conduction mode (DCM) allows a sinusoidal output current with low harmonic distortion (THD = 3.72%) to be obtained without current control loop and without the use of a current sensor at the output. The maximum power point tracking operation is obtained without the use of the current sensor. The DCM operation increases the current stress, but the proposed converter presents two switches and two input inductors sharing the input current in these components. The theoretical analysis, design procedure, and experimental results are presented for a prototype with a dc input voltage Vi = 30 V, an ac output voltage Vo = 127 V, and output power Po = 180 W. [ABSTRACT FROM AUTHOR]

Usually, the parallel-compensated inductive power transfer (IPT) topology fed by a current-source inverter is controlled through variable switching frequency and fixed 50% duty cycle method. This enables the system to operate at resonance frequency, which drifts due to load and other parameter variations. Owing to this control constraint, the load requirements are fulfilled by adding extra dc–dc chopper at the output. This paper presents a new control technique for a parallel–series/series IPT network, fed from a full-bridge current-source inverter to meet the load demand directly by an inverter. Therefore, the extra chopper stage at the output side of the converter is eliminated. The control goals are achieved through a two-loop control method, where the inner input current loop controls the source current and the outer output current loop meets the load requirements. The detailed steady-state operation, converter design, small-signal modeling, and control are reported, and experimental results obtained from a 1.6-kW lab prototype are included to verify the mathematical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

A merit of the interleaving reducing the switching harmonics allows for the reduction of the filter inductance. However, in the case of direct parallel voltage source inverters (VSIs), a severe circulating current occurs. To suppress the high frequency circulating current, coupled inductors (CIs) for the high impedance is inserted. However, the employed CIs induce a positive- or negative-sequence circulating current (i.e., a cross current) besides the zero-sequence circulating current already mentioned in the other papers. Due to different impedances developed by the current characteristics and the cross current in the CIs, VSIs becomes unstable when the resonant controllers are applied for the harmonic compensation such as 5, and 7th harmonics. In this paper, the cross currents and the impedances of CIs varying with the current characteristics are mathematically analyzed, and a novel current controller is proposed to solve this stability problem. The experimental results validate the proposed control scheme. [ABSTRACT FROM PUBLISHER]

A new single inductor dual buck full-bridge inverter is proposed in this paper. The inverter is improved on the basis of a dual buck inverter, and it retains the advantage of a no reverse recovery of body diode. The dc voltage utilization rate can be increased by adopting the voltage commutation bridge instead of the voltage-dividing capacitors in the inverter. In addition, comparing with other dual buck inverters, the inverter has just one filter inductor, which can make the volume and weight of the system decreased observably and improve the integration. The controlling method, combining the high- and low-frequency modulation, is adopted to weaken the complexity of control and improve the reliability and stability of the system. The operating principle, characteristic analysis, simulation and experiment are provided in this paper. A 1-kW prototype is established and tested, and the results of simulation and experiment verify the correctness of the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Connecting legs in parallel in a voltage source inverter is a way to increase the output current and, thus, its rated power. The connection can be made using either coupled or uncoupled inductors, and achieving an even contribution to the output current from all the legs is a crucial issue. Circulating currents produce additional losses and stress to the power devices of the converter. Therefore, they should be controlled and minimized. An efficient technique to attain such balance when coupled inductors are used is presented in this paper. The proposed technique can also be used when the inductors are uncoupled, since it is a particular case where the coupling coefficients are zero. This technique does not include proportional–integral controllers and does not require any parameter tuning either. The exact control action needed to reach current balance is straightforwardly calculated and applied. Experimental results are shown in this paper to verify the efficiency of the proposed balancing method. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A new space vector modulation, i.e., ZSVM3, for three-phase quasi-Z-source rectifier (qZSR) is proposed. All switches in the three-phase bridge can be turned on and turned off with zero current or zero voltage using the proposed ZSVM3 with no auxiliary circuit. The current through the inductors of the quasi-Z-source network operates in a boundary conduction mode or discontinuous conduction mode to achieve all freewheeling diodes turned off with zero-current switching (ZCS). At the same time, the switch in the quasi-Z-source network can be turned on with ZCS. Besides, the voltage stress of all switches is equal to dc-link voltage. The operation principle of the qZSR is analyzed in detail, and the calculated value of the quasi-Z-source inductor is given. The proposed theory in this paper is verified by a 2-kW prototype. [ABSTRACT FROM PUBLISHER]

In this paper, two switched-capacitor quasi-switched boost inverters (qSBIs) are proposed. By adding one capacitor and one diode to the qSBIs, the proposed inverters achieve high voltage gain with low voltage stress on active switches, capacitors, and diodes. The proposed inverters can extend to n-cell for voltage gain improvement. The operating principle, steady-state analysis, and impedance parameter selections of the proposed inverter are presented. A full comparison between the proposed inverter and other impedance-source inverters is addressed. A 500-W prototype is built to verify the operating theory of the proposed inverter in both the standalone mode and the grid-connected mode. Simulation and experimental results validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the zero sequence circulating current (ZSCC) will occur inevitably under space vector pulse width modulation or discontinuous pulse width modulation (DPWM). In this paper, the mechanism and the mathematical model of ZSCC are studied. Then, a hybrid PWM (HPWM) strategy is proposed to suppress the ZSCC based on the same zero sequence voltage injected, which is dependent on the common grid information. The dc voltage utilization of HPWM can be extended compared with sinusoidal PWM (SPWM). The number of parallel modules can be infinity theoretically by using HPWM. It is noted that there is no internal commutation among modules (expect the dq current reference). Finally, the feasibility and the effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high-voltage-gain boost converter is proposed. The proposed converter is constructed by adding an additional inductor to a conventional three-level-boost (TLB) converter. When compared with the conventional boost and TLB converters, the proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In particular, the proposed converter can reduce the losses of active devices by reducing the current of the switch compared to conventional converters, thus, can achieve high efficiency. In addition, the proposed converter automatically balances the output voltages for an unbalanced load without the need for any additional control strategy or auxiliary circuit. A 2-kW prototype converter was built and tested to verify performances of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, an improved transformerless single-phase single-stage grid-tied flying inductor inverter is presented. The negative terminal of the photovoltaic (PV) array is grounded in the improved topology, which increases reliability and suppresses the leakage current. The proposed topology has buck–boost capability without increasing the number of required components and has a high efficiency. An improved control algorithm for proper operation of the proposed topology which decreases switching losses has been investigated. Moreover, a perturbation and observation maximum power point tracking (MPPT) algorithm has been adapted to the proposed inverter, which does not utilize proportional–integral (PI) controllers, for the purpose of the MPPT. Furthermore, a design procedure of the passive elements of the converter based on the corresponding operating has been demonstrated. Simulation in MATLAB Simulink plus an experimental prototype is developed to reconfirm the designed results. Finally, a comparison study has been investigated for better clarification of the advantages and disadvantages of the proposed inverter. [ABSTRACT FROM PUBLISHER]

Photovoltaic (PV) microinverters dispense with the line frequency transformer, however at the cost of system grounding and ground leakage current problems. These have been erstwhile resolved by the topologies derived from buck, boost, buck–boost, Zeta, Watkins–Johnson, and Ćuk converters, or combinations of these. The Ćuk derived inverters, employing second-order input and output filters, offer the most efficient, lightweight, and economical solution in the class. This paper presents design and detailed operation of a Ćuk derived, common-ground PV microinverter in continuous conduction mode operation. The inverter is shown to be compatible with both linear and nonlinear loads, in stand-alone and grid-connected modes of operation. Optimal design rules of passive components are rigorously derived to ensure attenuation of input voltage ripples arising from the twin effects of switching and double-frequency output power oscillation. Additionally, the design rules also incorporate considerations of efficiency maximization and some aspects of easing control complexity. Inverter performance is experimentally validated with a 300 VA, 110 V, and 50/60 Hz laboratory prototype. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for Z-source inverter based on switched Z-source network is proposed. The proposed switched Z-source inverter can provide high voltage gain in low duty cycles. The continuous input current is one of the other advantages of the proposed inverter. The performance of the proposed inverter is investigated in different operating modes and the voltage and current equations of all elements and equations of critical inductance are calculated. Furthermore, the power losses and efficiency analyses are presented. The comprehensive comparison between the proposed inverter and the other conventional Z-source inverters shows its excellent performance. Finally, to prove the correct operation of the proposed topology, the experimental and simulation results using PSCAD/EMTDC software are presented. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

The five-phase coupled-inductor inverter is a newly proposed option for three-level five-phase inverter drives. This paper comprehensively analyzes the inverter including the coupled-inductor current, current stress on the dc-link capacitors, and a comparison of these performance aspects using three pulse width modulation (PWM) strategies. Mathematical derivations of the inverter currents and the associated current stress reveal that the current stress is not only influenced by the choice of modulation strategy, as in the neutral-point-clamped topology, but also by the value of coupled inductance; furthermore, the choice of the modulation strategy impacts the core loss of the coupled inductors. Three carrier-based PWM methods are considered: sinusoidal PWM (SPWM), and two methods with the common-mode voltage reduction (referred to as CMVR1 and CMVR2) for the five-phase coupled-inductor inverter. CMVR2 is shown to be the best solution if common-mode voltage reduction is required. The analysis demonstrates that SPWM performs better with respect to current stress and inverter losses, therefore is the preferable modulating strategy for the five-phase coupled-inductor inverter if common-mode voltage reduction is not required. The analysis is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper introduces a combination of two proposed efficiency improvement techniques for a microinverter with current mode control zero-voltage switching output stages. The first technique is dynamic dead-time optimization wherein pulse width modulation dead times are dynamically adjusted as a function of load current. The second method is advanced phase skipping control which maximizes inverter efficiency by controlling power on individual phases depending on the available input power from the photovoltaic source. Neither of the techniques requires any additional circuit components and both can be easily implemented in digital controller firmware. The two techniques were designed and implemented in a 400-W three-phase microinverter prototype. The experimental results validate the theoretical analysis of these techniques and demonstrate that a significant efficiency improvement can be achieved by combining the two proposed control techniques. [ABSTRACT FROM AUTHOR]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

A division–summation (D-\mathbf\Sigma) digital control for three-phase inverters to achieve active and reactive power injection has been presented. It can overcome the limitation of abc to dq frame transformation. However, the D-\mathbf\Sigma control requires four sets of control laws to cover four quadrant operations, namely, grid connection (power factor (PF) 1 $\sim\pm$0.866), rectification with PF correction, PF leading (0 \sim$ 0.866), and PF lagging (0 \sim$ −0.866). Moreover, the switching sequences for the four modes are also different from each other, increasing complexity of firmware programming. In this paper, improvement of the control law derivation and region selection for the (D), which can obtain the control law directly. Measured results from a 10-kVA 3 $\phi$ bidirectional inverter have been presented to confirm the improvement. [ABSTRACT FROM PUBLISHER]

Back-to-back converters have been typically used to interconnect microgrids. For a back-to-back current-source converter, the dc-link current ripple is one of the important parameters. A large ripple will cause electromagnetic interference, undesirable high-frequency losses, and system instability. Conventionally, with a given switching frequency and rated voltage, the current ripple can be reduced by increasing the dc-link inductor, but it leads to bulky size, high cost, and slow dynamic response. To solve this problem, this paper reveals that the current ripple can be significantly reduced by adjusting the gate patterns of space vector modulation between the rectifier and the inverter in a back-to-back converter. The experimental results verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

According to the requirement of fuel cell generation system, this paper presents a new single-stage and boost-voltage grid-connected inverter, as well as the signal modulation diagram in a line cycle. In the proposed inverter, one of the bridge legs is shared with a boost converter. The boost inductor current is designed in discontinuous conduction mode, which can effectively decrease low-frequency current ripple (LFCR) in the output current of the fuel cell. The switching modes of the proposed inverter are analyzed in positive and negative half line cycles, respectively. The LFCR in the output current of the fuel cell is analyzed, from which the design principle of the boost voltage inductor is obtained. The per-unit current values of the shared switches and the loss of the whole system are derived and compared with those of the conventional inverter. Experimental verifications are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In photovoltaic (PV) grid-connected generation system, the key focus is how to expand the generation range of the PV array and enhance the total efficiency of the system. This paper originally derived expressions of the total loss and grid current total harmonics distortions of cascaded inverter and H-bridge inverter under the conditions of variable output voltage and power of the PV array. It is proved that, compared with the H-bridge inverter, the operation range of the cascaded inverter is wider, whereas the total loss is larger. Furthermore, a novel online variable topology-type grid-connected inverter is proposed. A bidirectional power switch is introduced into the conventional cascaded inverter to connect the negative terminals of the PV arrays. When the output voltages of the PV arrays are lower, the proposed inverter works under cascaded inverter mode to obtain wider generation range. When the output voltages of the PV arrays are higher, the proposed inverter is transformed into equivalent H-bridge inverter mode to reduce the total loss. Thus, wider generation range and higher efficiency are both implemented. Specific demonstration of the proposed inverter based on five-level cascaded inverter is presented. The detailed experimental results verify the accuracy and feasibility of the theoretical analysis and the proposed inverter topology. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved half-bridge inverter with wide-input-voltage capability for ozone-driven circuits. The study is motivated because the limited regulation of input voltage often affects the operation flexibility of ozone-driven circuits. Therefore, a modification of a half-bridge inverter along with a multiwinding coil design is proposed in this study, anticipating an increase in the range of input voltage and benefiting the industry applications. To confirm the practicality of this method, a hardware circuit was made with extensive validation. Experimental outcomes support the feasibility of this proposed method for ozone generators, exhibiting a potential of the method extending to other voltage-source applications. [ABSTRACT FROM PUBLISHER]