Search

Graphene has attracted great interest for its distinctive band structure and physical properties. Results from previous studies show that a graphene cathode can provide stable field emission and intense emission in a vacuum. In this paper, a graphene cathode was fabricated using chemical vapor deposition (CVD) on copper electrodes, and the breakdown of the cathode in a high-pressure gas was studied. A low-jitter, self-breakdown gas spark switch based on a graphene cathode is proposed in this paper. The impulse-breakdown characteristics of this switch in a quasi-uniform electric field were studied. When the gap length is 5 mm, and the gas pressure is 0.6 MPa, the average breakdown voltage ($U_{\mathrm {BD}}$) is nearly 85.9 kV, and the voltage jitter is only 3.2%; these values are much lower than those for pure copper cathodes and graphite cathodes. The graphene cathode is found to be a suitable choice for use as a high-power gas switch in applications requiring an intense emission source. [ABSTRACT FROM AUTHOR]

This paper has introduced two important indexes, turn-off surge voltage (TSV) on power switch and peak positive pole potential (PPPP) of storage batteries, which can be used to evaluate switching transient process of high-voltage energy storage system. Research on them is of great significance to power switch choice and high-voltage isolation design in engineering applications. Power switch response process at the turning off moment and transient process in freewheel stage have been analyzed by the established small-signal model of single power switch; then, a power switch test platform for hybrid energy storage system was built to verify it. Taking pulsed-power supply charging device with a novel inductor of low resistance and high inductance as a research object, this paper has analyzed dynamic process of the TSV and the PPPP at the turning off moment through establishing state space model of the whole system. Comparison shows that the numerical curves match the simulated curves well. Finally, the exactness of the employed model has been further verified in two pulse capacitor charging experiments. [ABSTRACT FROM AUTHOR]

The planned China fusion engineering test reactor (CFETR) needs one or more negative-ion-based neutral beam injectors (N-NBIs) with a beam energy of 500 or even 1000 keV. In order to prepare for CFETR, a prototype of CFETR N-NBI is being designed. The prototype needs an acceleration grid power supply (AGPS) rated at 200 kV/25 A with a maximum pulselength reaches to 3600 s. The AGPS adopted a single-stage inverter-type high-voltage power supply (HVPS). The output voltage ripple is an important specification of the AGPS, which can affect the efficiency and stability of N-NBI system by influencing the beam divergence. However, the conventional methods cannot be used to limit the output voltage ripple of the inverter-type HVPS used as AGPS of CFETR N-NBI prototype. This paper simplified the AGPS to an insulated three-phase three-level (TPTL) dc–dc converter connected with a dual dc link. The working process of the TPTL dc–dc converter with duty-cycle modulation has been analyzed, and two main continuous conduction modes are described. The influence of key parameters such as duty cycle of inverter, leakage inductance of transformer, and output current on output voltage ripple is analyzed. Based on the analysis results, a so-called combined control strategy was proposed to keep the output voltage ripple at a level. The proposed strategy is suitable for the cases where the object output voltage is below 175 kV. Some simulations were carried out by using MATLAB/Simulink. The results showed that the analysis in this paper is reliable and the proposed control strategy has a good performance. [ABSTRACT FROM AUTHOR]

This paper proposes unconventional control techniques for a portable power supply consisting of electric double-layer capacitors (EDLCs), a dc–dc converter, and a low-impedance load such a plasma load. Between the EDLCs and the plasma load consuming high power, a dc–dc converter is required to control the output voltage from the rapidly decreasing voltage of EDLCs. In addition, the dc–dc converter should maintain a set point by responding to arcs occurred in plasma process. This paper proposed hybrid analog and digital controls for a nonideal boost converter which was setup by theoretical analysis. The proposed system is verified with experiment and simulation. As a result, the proposed control method can maintain the constant output voltage longer than a traditional analog pulsewidth modulation control. [ABSTRACT FROM AUTHOR]

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

Magnetic pulse compression (MPC) systems are suitable for generating dielectric barrier discharges (DBDs) owing to their capability of producing high-amplitude, short pulse voltage waves. This paper proposes a high-frequency, bipolar magnetic compression system to study DBD plasma characteristics. First, the principle of bipolar MPC is explained [a bipolar MPC system comprises a full bridge inverter circuit, pulse transformer (PT), and magnetic switch (MS)]. Additionally, the design of the PT and MS is described. Then, the waveform of the resistive load is tested and compared with PSpice simulation results. It was found that the nanosecond pulse generator produces a pulse on a resistor with an amplitude of 0–13 kV, a rise time of approximately 100 ns, and a repetition frequency of 0 to several kHz. Finally, this paper studies the plasma characteristics under the application of a high-frequency bipolar pulse, and the charge–voltage Lissajous figure of the discharge waveform is analyzed. Combining discharge photographs and theoretical calculation results yields the relationship between the discharge characteristics and the frequency, which enriches the theoretical study of high-frequency bipolar discharges. [ABSTRACT FROM AUTHOR]

High-voltage high-power pulse switches are built with semiconductor devices, preferably thyristor, due to the superior performance that they offer. Triggering methods classify the thyristor as electrically triggered thyristor (ETT) and light triggered thyristor (LTT). Due to the specialized gate constructions and many build-in protections, the cost of LTT is much higher than ETT. The operating modes in applications, such as crowbar, do not require all these build-in protections. In this paper, the operation of a crowbar is analyzed, and the build-in protections of LTT are reviewed. This paper proposes three experiments for the design selection of thyristor, between ETT and LTT, for crowbar applications. The experiments cover the electrical performance as well as electromagnetic emissions in a 10-kV, 1-kA crowbar built with both ETT as well as LTT, which can be used to benchmark the performance of the crowbar circuit. From the three experiments, the performance of ETT-based crowbar is found to be comparable with LTT-based crowbar. Based on the experiments carried out with the proposed benchmarking approaches, this paper shows that ETT-based crowbar is a cost-effective solution for crowbar applications. [ABSTRACT FROM PUBLISHER]

This paper presents the effect of stray capacitances in bipolar (negative and/or positive) pulses generated by the two different topologies of the solid-state Marx modulators. According to the analysis, the stray capacitances influence the energy transfer from the Marx modulator capacitors to the load affecting the bipolar (negative and/or positive) pulse rise time. This paper deals with the structure design to reduce the influence of the stray capacitance and to improve the pulse rise time of these bipolar solid-state Marx modulators. A four-stage laboratory prototype of the two topologies has been assembled using 1200-V insulated gate bipolar transistors and diodes, operating with 1000-V dc input voltage and 1-kHz frequency, producing 4-kV bipolar pulses, with 5- \mu \texts pulse duration and 120-ns rise time, into a resistive load. [ABSTRACT FROM PUBLISHER]

Studies have been taken into the breakdown voltage jitter of corona-stabilized switch at high repetition rate up to several kHz. It is thought that the gas recovery affect the jitter of breakdown voltage directly at high repetition rate, because the gas switch will breakdown at a low voltage if the gas cannot fully recover. The breakdown voltage jitter is called voltage jitter in the following paper. However, based on the experimental results, the voltage jitter still exists at low repetition rate, even at single-shot mode. This is not explained by the previous studies. In this paper, voltage jitter below 100 Hz of a corona-stabilized switch is investigated experimentally. A corona-stabilized switch is introduced, using a cylindrical electrode as the cathode and a plane electrode as the anode. The gas used between the electrodes is SF6. A negative pulse with a maximum width of 30~\mu \texts is used to charge this switch. The tested factors include gas pressure, gap space, repetition rate, and switch geometry. Experimental results show that voltage jitter is mainly affected by the gas pressure and switch geometry. It is seen that voltage jitter decreases as gas pressure increases and a suitable cathode geometry presents a low voltage jitter. Critical volume is a region close to the highly stressed electrode, where the presence of an electron will lead to an electron avalanche which attains a critical size and hence leads to a stabilizing corona. Critical volume is introduced to explain the experimental results. It is found that less voltage jitter can be achieved with a smaller and more concentrated critical volume, as well as efficient corona stabilization. The results indicate that voltage jitter may be reduced by optimize the critical volume at low repetition rate. [ABSTRACT FROM PUBLISHER]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

Compulsators are ac generators which are used for electromagnetic launch applications over the past few decades. This paper presents the work carried out by the authors to design a compulsator for a railgun which has been built and tested with a capacitor bank of 20 kJ as the pulsed-power source in the author’s laboratory. The generator topology selected for the compulsator is a single phase, two-pole machine with iron core and passive compensation. The design is based on the criterion of achieving maximum projectile exit velocity with the additional condition that natural current zero is synchronized with the instant of the projectile’s exit. The effect of varying the different parameters of the compulsator on the performance of the system has also been studied and discussed in this paper. By means of performance analysis, the necessary background for the design of the actual compulsator has also been achieved. [ABSTRACT FROM PUBLISHER]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

This paper proposes an active resonance circuit based on multiple series gaps (MSG) with voltage-dividing network and self-charging trigger device. The working principle of active resonance circuit, MSG, and triggering device is described in detail. To determine the optimal parameter setting of MSG, the effects of the voltage frequency, equalizing resistance, and voltage-dividing capacitance on the voltage distribution of MSG are analyzed by simulation. To realize the interrupting process of short fault current and determine the operation requirements of the main devices of precharge direct current (dc) circuit breaker, a simulation model of interrupting short fault current is performed. Furthermore, an experiment of four-series gaps is presented to verify the turn-on characteristic of the MSG and an experiment of artificial current zero is set up to testify the feasibility of the active resonance circuit. The simulation and experimental results show that the active resonance circuit proposed in this paper can generate an artificial zero current and is suitable for precharge dc circuit breaker. [ABSTRACT FROM AUTHOR]

Bipolar junction transistors (BJTs) have been widely studied and used in nanosecond high-voltage pulse generators due to the advantages of fast switching speed and high repetitive frequency. Usually the Marx-type circuit is used to raise the peak value of output pulses. In this paper, a traditional BJT-Marx circuit using charging resistors is analyzed theoretically and experimentally. Based on the results, the structure of a circuit is changed to decrease the isolation voltage across the resistors, and diodes are used to replace charging resistors to block capacitors discharging to resistors. Experimental results showed that the three Marx generators proposed in this paper output pulses with higher voltage amplitude, and the last improved circuit outputs pulses with faster fall times at a higher efficiency. [ABSTRACT FROM AUTHOR]

We present a new technique for the design and test of coaxial switched oscillators (SWOs). In this paper (Part I of a two-part paper), we concentrate on the electrostatic design of coaxial SWOs. We introduce a new design for the electrodes, which have been conceived as conformal surfaces in a geometrically convenient curvilinear space where Laplace equation is solvable. Analytical solution of the electrostatic fields is presented, discussed, and validated using numerical simulation. A prototype of an SWO based on this design is built and validated using experimental data. [ABSTRACT FROM AUTHOR]

This paper shows how to use modular Marx multilevel converter diode ( \textM^3 CD) modules to apply unipolar or bipolar high-voltage pulses for pulsed power applications. The \textM^3 CD cells allow the assembly of a multilevel converter without needing complex algorithms and parameter measurement to balance the capacitor voltages. This paper also explains how to supply all the modular cells in order to ensure galvanic isolation between control circuits and power circuits. The experimental results for a generator with seven levels, and unipolar and bipolar pulses into resistive, inductive, and capacitive loads are presented. [ABSTRACT FROM AUTHOR]

In order to generate bipolar high-voltage (HV) pulses across certain load from HV dc (HVdc) power supply, a voltage source inverter (VSI) stage should be inserted between the load and the supply. In order to meet the required HV level, series connection of semiconductor devices should be employed with dynamic voltage sharing between the involved devices. Modular multilevel converter (MMC) can be used instead of the conventional two-level VSI to alleviate the complexity introduced by the deployment of series-connected devices. The voltage level of the HVdc power supply and the voltage rating of the available semiconductor devices determine the suitable number of MMC voltage levels ( $N$ ). Capacitor voltage balancing is a vital issue for proper operation of the MMC. In general, conventional sensor-based balancing techniques require a significant amount of measurements, which increases the complexity of the system. In addition, the high dv/dt during switching times causes electromagnetic interference, which may adversely affect the accuracy of the measurements. In this paper, a sensorless voltage balancing technique is proposed for the MMC-based bipolar HV pulse generator that reduces the system sensitivity, cost, and complexity. A detailed illustration of the proposed approach is presented in this paper. The simulation and experimental results are used to validate the proposed concept. [ABSTRACT FROM AUTHOR]

This paper discusses a study made for good asymmetric three-stage electromagnetic coilgun launching medium-weight projectile. Different lengths, number of turns, and switching times are chosen for each individual coil to get better results. Two detailed investigated models have been presented, including the effect of the switching time. Medium-caliber projectile of \text weight = 0.5 kg is employed in this paper. The results confirm that the second model asymmetric coilgun has 16.96% higher output speed, 63.92% lower length, and 57.5% lower launching time than the first model asymmetric coilgun. The obtained results have been recorded using the transient time electromagnetic simulations. [ABSTRACT FROM PUBLISHER]

This paper proposes a compact high-voltage pulse electron gun power supply (EGPS) consisted of interleaved capacitor-charging power supply (CCPS) with a series-resonant converter (SRC) to drive the electron tube. Requirement specifications are −40 kV, −7 A (280 kW), and continuous output lower than ±1% ripple stability lasted few seconds with <1 ms charging and discharging times. To meet the design specifications, eight stacks operate in parallel, and each stack has a 45° phase shift switching pulse width modulation (PWM) method. Each designed CCPS can supply −40-kV voltage and −0.9-A current. In addition, the proposed CCPS has the SRC to reduce the switching loss. The SRC is a famous topology, which presents main characteristics such as high-power density and efficiency. To prove the validity, this paper is confirmed by the simulation and experimental results of the fabricated −40-kV output CCPS with water load. Then, we implemented the fabricated EGPS to the electron tube. [ABSTRACT FROM PUBLISHER]

Paralleled pulse-forming units (PFUs) with different triggering delays might be a paramagnetic way for generating flat-topped current wave for electromagnetic launch. Many researchers have reported that multiple capacitive storage PFUs were implemented such current waves in laboratories. However, due to its low energy density, the applications of the capacitive pulsed-power supplies are limited. Since the inductor has advantages in energy density, the inductor pulsed-power supply becomes one of the hottest topics recently. The slow transfer of energy through capacitive hybrid meat grinder with inverse current commutation with semiconductor devices proposed by Tsinghua University has demonstrated its advantage and applicability recently. Using this kind of topology, this paper proposes the design of an inductive storage PFU with a stored energy of 100-kJ. The maximum load current reaches to 50 kA and its pulsewidth is at least 5 ms. The optimized inductive storage PFU shows superiority in contrast to the capacitive storage PFU with the same energy. This paper offers the theoretical analysis and the testing foundation for investigating the inductor pulsed-power supply with higher energy. [ABSTRACT FROM PUBLISHER]

Slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, which was proposed by the Institute for Advanced Technology, added a capacitor into the traditional meat grinder circuit. Even though its energy density is slightly less than the corresponding pure inductance system, it can reduce the voltage across the opening switch and maintain the high multiplication factor of the opening current. The performance of the STRETCH meat grinder circuit depends on multiple parameters. The inductance ratio ( n=L1 / L2) and the capacitance (C) are the two vital factors, which have a crucial influence on the system performance, such as the voltage over the opening switch ( V_{\rm Sopm}) , the current multiplication factor ( m$ ), and the ratio of the maximum capacitive energy over the total inductive energy ( $\eta )$ . Thorough studies have been carried out in this paper on the relationship between the above two factors and the three performance criteria. This paper also discusses and analyzes the chosen of the key parameters ( $n$ and $C$ ) for a single-stage STRETCH meat grinder with 2-mH total inductance, which is made up of two serial coils with 0.95 coupling factor. The opening current of the main switch is 1 kA, which constitutes a 1-kJ inductive pulsed-power supply. It fully takes the advantage of the STRETCH meat grinder topology, intensifies the study of the inductive pulsed-power supply with higher energies, and is easy to be utilized for practical application. [ABSTRACT FROM PUBLISHER]

The STRETCH meat grinder is one typical inductive pulsed-power supply topology for electromagnetic launch system. It has remarkable current amplification ability as a single unit, but one module cannot provide enough amplitude and width for the load current of the railgun launching. This paper discusses the effects of different triggering delays on the load current with two STRETCH meat grinder modules. To reduce the magnetic field coupling between the two modules, the two main switches are opened simultaneously. To make the load current waveform with no notch, the thyristor of the first module is triggered when its pulse-forming capacitor is fully reversely charged. For the thyristor of the second module, we consider several time points of triggering delay. Because of the practical constraint for the maximum rail current that ensures no rail erosion, the rectangular waveform is the most appropriate load current waveform. Therefore, the comparing criterion can be defined as the ratio of the load current waveform area and its maximum rectangle area at different current levels. Higher ratio means that the current is more like a rectangular wave and is better accordingly. Based on the above criterion and extensive simulation research, we found that the best delay time is the moment when the capacitor is reversely charging the inductor completely. This paper and the result are of great theoretical significance for the further study on the collaborative triggering of multiple STRETCH meat grinder modules. [ABSTRACT FROM PUBLISHER]

This paper presents the design and implementation of a 40-kV, 20-kJ/s high-voltage capacitor charger based on a series/parallel resonant converter. The inclusion of the parallel resonant capacitor component in this circuit results in the production of a trapezoidal resonant current, which reduces conduction loss. This capacitor is practically realized as a part of the balancing network of the high-voltage rectifiers in the secondary side of the circuit. Particular attention in this paper is paid to the high-voltage transformer, which must be carefully designed to provide the required functionality without negative impact on the resonant circuit. A PSpice simulation has been used to prove that the proposed control method for the circuit is valid. This is supported with the experimental results, which verify that the operation of the circuit is as expected and that the converter is able to meet all the design criteria with an efficiency of up to 96%. [ABSTRACT FROM PUBLISHER]

In this paper, a compact circuit topology is presented for pulsed power generation with a semiconductor opening switch (SOS). Such circuits require the generation of a fast forward current through the diode, followed by a reverse current that activates the recovery process. In general, magnetic switches are used to switch the diode current from forward to reverse. Therefore, adjustment of the output voltage of an SOS pulser is difficult. This paper introduces a circuit that allows an adjustable output voltage of the pulser. A solution is realized with a premagnetizing circuit on the primary winding of a pulse transformer (PT), so that a third winding is not needed. The primary capacitor voltage can now be varied while maintaining proper saturation of the PT. [ABSTRACT FROM PUBLISHER]

This paper presents an electromagnetic simulation method for spark-gap switched pulse generators (SGSPGs). Electromagnetic simulation programs can be useful for designing nanosecond or subnanosecond SGSPGs; however, these programs do not support simulation models of spark-gap switches. This paper describes a simulation method that determines electric field at an observation point in the SGSPG by replacing the spark-gap switch with a step voltage source. In this simulation, the discharge properties of the spark-gap switches, including the breakdown voltage and rise time, are determined using the results of the studies on electrical breakdown. A 1-ns single pulse-forming line was fabricated to validate the proposed method. The simulated waveform was in good agreement with the measured waveform. [ABSTRACT FROM PUBLISHER]

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

This paper describes a study on the high-voltage compact solid-state pulsed-power modulator for parallel reactor operation. The current capacity of the pulsed modulator has been improved to drive multiple reactors in parallel. The pulse discharge switch uses the IXYK120N120C3 (1200 V/120 A) insulated-gate bipolar transistor for a high current output. The gate driver has been improved according to the characteristics of the replaced switch. The output specifications of the modified pulsed-power modulator are a maximum output voltage of 40 kV, a maximum output current of 300 A, a pulsewidth ranging from 1.5 to $5~\mu \text{s}$ , a maximum repetition rate of 3 kHz, and an average power of 13 kW. The modulator has the dimensions of $450 \times 475 \times 600$ mm3, a maximum peak power of 12 MW, and a maximum power density of 93 kW/L. A resistive load experiment and a plasma reactor parallel drive test were performed. Four parallel reactors were driven using one modulator. In addition, a 50% reduction in the concentration of toluene was obtained through the experiment of the toluene gas treatment using only parallel plasma reactors. [ABSTRACT FROM AUTHOR]

Amorphous magnetic core has been widely used in pulsed power technology with applications including plasma science research, high-power microwave generation, and material surface treatment. For different applications, dynamic properties of the magnetic core will vary with stimulated magnetic field which determines by magnetization time and waveform of the driving voltage. In this paper, toroidal amorphous magnetic core ($\Phi ~540$ – $740\times25$ mm) was investigated theoretically, numerically, and experimentally. Specifically, the circuit is analyzed. A high-voltage test stand, which can generate different driving voltages with same components, was designed and developed in our laboratory. Dynamic properties, including magnetic induction change, coercive force and losses, were studied under three different typical waveforms with the same magnetic flux. Driving voltages of the pulses were 12, 12, and 6 kV and the magnetization rates were 0.6, 1.2, and 0.6 T/ $\mu \text{s}$ , respectively. Experimental results show reasonable agreement with the numerical analysis. [ABSTRACT FROM AUTHOR]

This paper addresses the design of a solid-state bipolar pulsed-power modulator based on a series of stacked power cells that realize a simple and robust structure. Each cell is charged in parallel by an LCC resonant converter independently of the discharging loop. A passive cell-balancing design is implemented. The power cell using insulated gate bipolar transistors (IGBTs) can operate in bypass mode without an additional component, and the circuit operation was analyzed. A simple gate driving method, which provides synchronized gate signals without an extra power source of each gate driver using two control loops and isolation transformers, is implemented for the proposed bipolar pulsed-power modulator based on stacked cells. Moreover, an unexpected gate turn-on problem was solved by an additional off signal. To validate the proposed structure and the gate driving scheme, a three-cell, 1.2-kV, 110-A, 1.5- to 4- $\mu \text{s}$ , 3-kHz laboratory experimental prototype test was conducted. The results proved the reliability of the proposed solid-state bipolar pulsed-power modulator. [ABSTRACT FROM AUTHOR]

This paper proposes a flyback-circuit-based design of a trigger circuit for a high-power gas switch. By incorporating a flyback circuit in a high-power gas switch, it is possible to generate a high step-up ratio and high-voltage pulse by using a transformer. Furthermore, simple trigger circuit having the minimum possible number of components (transformer and switch) can be realized. When an inductor is used as an energy storage element, energy is stored as a current source, and thus, the element can operate reliably when low impedance exists between the trigger node of the switch after triggering. According to the fundamental operating principle of a flyback circuit, the proposed trigger circuit is designed considering the maximum trigger voltage and energy required for a high-power gas switch. To verify the proposed design procedure and feasibility of the trigger circuit, a compact trigger circuit (7.5 kV, 1.3 mJ/pulse) is simulated using the PSpice program and implemented. Based on this compact circuit, a trigger circuit (20 kV, 100 mJ/pulse) for a triggered vacuum switch (TVS) is developed, and the tests with an actual TVS (3.3 kJ) are carried out. [ABSTRACT FROM AUTHOR]

Marx generator using all-solid-state devices has been studied for many years. Higher parameters are always the demand for new applications. Traditional all-solid-state Marx generator can output high voltage due to its series topology, but the current is always limited by the switch. In this paper, a stage-stage paralleled topology of Marx generator for high current has been proposed. Topology structure and driving mode comparison for current balance have been analyzed. The paralleled driving mode for the current balance and the shaping waveform has been proposed. For experiment, a four-stage-four-paralleled Marx generator with metal–oxide–semiconductor field-effect transistors (MOSFETs) has been constructed with output pulses 2.2 kV, 730 A (depending on the load), rise time of 31 ns, fall time of 56 ns, and adjustable pulsewidth from 400 to 800 ns. [ABSTRACT FROM AUTHOR]

This paper describes the development of a small field-distortion spark gap switch. Comprehensive experimental studies made with the switch revealed its self-breakdown characteristics, voltage operating range, time delay and jitter, repetition frequency, and finally the electrode erosion processes and duration of its service lifetime. A series of design improvements were required to be implemented in the switch design. For example, to reduce the structural inductance of the switch and to improve its working characteristics, the main electrode was designed as a circular track structure. Similarly, to increase the operation stability and reduce the self-breakdown probability, the trigger electrode was designed as a disk-like structure. Moreover, to balance the gas pressure in the discharge region and increase the stability during closure, a circular hole was added at the center of the trigger electrode. The compact switch has a small size of only 150 mm $\times42$ mm, a weight of 1.5 kg, and can be successfully operated at a voltage over 110 kV, at a repetition rate between 1 and 50 Hz and having a jitter of less than 4 ns. It was experimentally demonstrated that during normal operation conditions, the switch lifetime exceeds 100 000 shots. [ABSTRACT FROM AUTHOR]

Working performances of laser-triggered vacuum switch (LTVS) mainly rely on the interactions of laser with target materials. Influences from target configuration, which is one of key factors in the interactions, are neglected so far. The trigger performances of LTVS with different target configurations are studied in this paper. Relevant influence factors about target configurations are discussed briefly based on theoretical analysis about the trigger process. The test prototype is established based on detachable vacuum chamber. The trigger characteristics of LTVS with different target structures, target depths, and laser focal positions are compared. The relationships between target configurations and trigger performances of LTVS are analyzed and discussed. The preferred targets in LTVS are suggested while considering its lifetime. The test results prove that the conical target shows the best trigger performances compared to other targets. Due to the enlarged laser irradiated area and shortened plasma moving distance, the delay time of LTVS reduces with the decrease in conical target angle and the increase in target depth, while the delay time is controlled within 32 ns. Benefited from laser reflection and plasma collision, the trigger performances of conical targets can be enhanced by focusing laser on the target side surface. In particular, the 90° conical target with 1.5 mm depth is suggested to be employed in LTVS products. [ABSTRACT FROM AUTHOR]

A quench protection switch (QPS) is indispensable to protect the magnet coils from the damage of quench in a superconducting Tokamak. In this paper, a QPS based on artificial current zero is involved. The vacuum circuit breaker (VCB), which is driven by a high-speed electromagnetic repulsion mechanism, is used as the main circuit breaker (MCB). Two kinds of commercial vacuum interrupters (VIs), which have contacts generating axial magnetic field (AMF) and transverse magnetic field (TMF), respectively, are applied. The breaking current with an amplitude of 10~25 kA is generated by an LC oscillating circuit. The countercurrent with frequency in the range of 500–3000 Hz is provided by a commutation branch. The interruption performance of the two kinds of VIs under different breaking current and countercurrent frequencies is investigated. The experimental results indicate that the differences in interruption performance under the two types of contacts are increasing with larger frequencies of countercurrents. [ABSTRACT FROM AUTHOR]

In this paper, we present the first implementation of our 0–60-kV picosecond rise time 1–10-ns pulse generator. The pulse generator will be used in future work to generate a (sub-)nanosecond streamer plasma for air purification research. The first implementation of the pulse generator is a single-line pulse generator with an oil spark-gap, which generates 5 ns pulses with a 200 picosecond rise time and can operate at repetition rates of over 1 kHz into a 50 \Omega load. In this paper, we evaluate its performance and describe how we measure the very short pulses with an integrated and calibrated D-dot sensor. Furthermore, we present 3-D EM simulations of the 5 ns pulse generator and show that the simulations are in good agreement with the measurements. We previously described methods to flexibly vary the pulse duration of the pulse source by (artificially) changing the length of the pulse forming line (PFL). Here, we test these methods and find that changing the length of the outer conductor of the PFL and inserting magnetic material at the end of the PFL is a suitable method to change the pulse duration. Finally, we measure the breakdown voltages of the oil spark-gap and discover that higher pulse repetition rates are possible at higher oil pressures and smaller gap distances. [ABSTRACT FROM AUTHOR]

This paper describes the design, implementation, and comparison of high-voltage capacitor chargers for a solid-state pulsed power modulator (SSPPM). The three different converter topologies are a series resonant converter operating at a discontinuous conduction mode with switching frequency control (SRC_DCM_SFC), a series resonant converter operating at a continuous conduction mode with phase shifted pulse width modulation control (SRC_CCM_PSPWMC), and a series–parallel resonant converter operating at the CCM with SFC (SPRC_CCM_SFC). On the basis of these converter topologies, 10\-kW\rm{average} high-voltage capacitor chargers are designed for the three types of SSPPMs, which have the following maximum output specifications: 1) SRC_DCM_SFC: 60 kV, 300 A, 3 kpps, and 50 \mus; 2) SRC_CCM_PSPWMC: 10 kV, 50 A, 50 kpps, and 10 \mus; and 3) SPRC_CCM_SFC: 40 kV, 150 A, 7 kpps, and 10 \mus. Although the pulse output specifications are different, it is worth comparing the resonant inverter topologies and the control methods from the viewpoint of the losses, control characteristics, and merits and demerits of the high-voltage capacitor chargers. From the analysis and investigation of the three resonant inverters, the design procedure, including the determination of the resonant tank parameters, is provided, which considers the design of the high-voltage capacitor charger. PSPICE simulation is used to elucidate the effects of the resonant tank structure and its parameters, and the resonant current waveform and losses of the Insulated Gate Bipolar Transistor are compared. Finally, experiments for each charger are performed under various load conditions, and the comparison results of the three capacitor chargers, including the conduction and switching losses, control characteristics, and overall efficiency, are discussed in this paper. [ABSTRACT FROM AUTHOR]

This paper is concerned with the development and testing of a compact flat format multichannel electrically triggered rail spark gap. It is tested for multichannel discharge under atmosphere for high reliability. Multichannel discharge rail spark gaps can be developed using laser trigger or fast rising trigger voltage pulse (>5~kV/ns). The extra volume and weight added by laser or fast triggering circuits limit the use in pulse power applications. An electrically multitriggered low-inductance spark gap is developed. It is used as a multichannel low-inductance discharging element in a fast rising high-current generation system. The trigger of such rail gap is realized using the set of round copper pins similar to single trigger pin in a field distortion spark gap. In parenthesis, five different trigger pins are located in main trigger plate and these are isolated with high impedance. Therefore, five different trigger signals are generated with time difference of tens of nanoseconds. The major material erosion at five points of both stainless steel main electrodes confirms the multichanneling discharge. The main gap spacing in this switch is 4 mm and the trigger is located close to the ground electrode for reducing the delay time and jitter in delay time. This paper shows the trigger circuit design, main gap voltage, and trigger voltage effect on the closing of the spark gap and picture of electrodes after use. [ABSTRACT FROM AUTHOR]

A thermal model of a switched reluctance linear launcher is presented in this paper. The accuracy of the thermal model is verified by comparing experimental data with those results derived from finite-element method simulation. The temperature distribution of a switched reluctance linear launcher is derived based on the stator copper losses as the main heat power with measured stator winding current by the current sensor. The maximum temperature rise curves under different ambient temperature and different heat power of winding A are studied. The heat dissipation power of four air convection surfaces under different ambient temperature and the different heat power of winding A is also studied. Furthermore, this paper achieves optimization in thickness of the stator plate and in adding fins to the stator plate for heat dissipation with the present model. It is shown that the stator plate is the maximum heat dissipation power surface so that it can be adopted as the main heat dissipation channel and the effect of heat dissipation is obvious by adding fins to the stator plate. [ABSTRACT FROM PUBLISHER]

Normally, a three-electrode spark–gap switch is controlled by the application of an external trigger impulse. In this paper, a novel self-breakdown sharpening switch based on the three-electrode spark–gap switch is proposed. However, in this paper, the trigger electrode is connected to ground through a resistor, with the prespark between the trigger and the main electrodes providing the electrons and ions that initiate conduction of the main gap. A prototype sharpening switch with a breakdown voltage of 116.0 kV \pm 1.0 kV and a breakdown time of 3.396\ \mu\s\pm 0.036 \ \mu\s is described. When compared with a conventional two-electrode spark–gap sharpening switch, the novel sharpening switch has both a more stable breakdown voltage and lower jitter, and the dc breakdown and impulse breakdown characteristics of the two types of switches are presented and compared. When the impedance of the resistor connected to the trigger electrode is high, it is demonstrated that both the value of this resistor and also the type of load have little effect on the characteristics of the novel switch. However, the breakdown voltage of the novel sharpening switch was found to be sensitive to the rise time of the input pulse from the trigger generator. The prototype sharpening switch has a lifetime at least 20 000 shots and is now in use in a major pulsed power conditioning system. [ABSTRACT FROM PUBLISHER]

This paper discusses the modeling of a peaking switch to study the reduction in rise time for the subnanosecond duration pulses. The effect of the various shapes of input pulse, inductance, and interelectrode distance on the output voltage and wave shape is discussed in this paper. The modeling has been carried out using the electromagnetic and microwave modeling software of Computer Simulation Technology. [ABSTRACT FROM PUBLISHER]

Nuclear fusion reactors, such as the tokamak in the International Thermonuclear Experimental Reactor (ITER) project, usually involve extremely sophisticated high-voltage power supply systems, which provide exciting research challenges. In the short term, the major challenges in power supplies of the ITER and other fusion reactors include the following: 1) fast current control of vertical stabilization (VS) coils and 2) dynamic compensation of reactive power and harmonics. In the long term, the power supply systems in fusion reactors provide opportunities for optimizations at both component and system levels. In this paper, modular multilevel converters (\M^2\LCs) are adopted to tackle the short-term challenges. Circuit structures, pulsewidth-modulation methods, and fault-tolerant operation strategies are presented. The configuration and control strategies of \M^2\LC in VS coils are fully studied and verified with real-time simulations. Compared with existing circuit solutions in fusion reactors, the \M^2\LC -based circuits will have better dynamic response, higher reliability, smaller footprint, and reduced weight. As an outlook to the long-term developments of the fusion power supplies, comprehensive real-time simulations are also discussed. Furthermore, as the future development direction of power electronic devices, the wide band gap devices are discussed at the end of this paper. [ABSTRACT FROM PUBLISHER]

This paper describes the studies performed to identify a suitable design solution for the power supply of the residual ion dump for neutral beam injectors (NBI) of International Thermonuclear Experimental Reactor (ITER). A novel approach has been proposed based on the series of two power supplies, one to produce the average output voltage and one devoted to the generation of the required ac component. The paper is focused in particular on the schematic circuit adopted to generate the alternating component that is meant to use floating capacitors to produce a trapezoidal voltage component superimposed to the dc one. [ABSTRACT FROM PUBLISHER]

In this paper, we discuss and demonstrate the potential of normally-on GaN high-electron-mobility transistors (HEMTs) as opening switches in miniaturized pulsed-power circuits. The high-breakdown electric field of GaN (~3 MV/cm) makes it possible to fabricate high-voltage devices in small dimensions, resulting in smaller parasitics and faster switching times. GaN HEMTs as opening switches are compatible with inductive topologies, which offer more than one order of magnitude higher energy density than capacitive topologies, allowing further miniaturization of pulsed-power systems. In this work, we demonstrate the application of fabricated 1.5-kV normally-on GaN HEMTs on an inductive switching topology, resulting in 300-fold voltage step-up, which makes it possible to generate high-voltage pulses with a low-voltage dc source in miniaturized circuits. [ABSTRACT FROM AUTHOR]

High-frequency power amplifiers can be equipped with complementary pulse-compressor systems to fulfill the advanced cavity power requirements. Microwave pulse compression is a power extraction method based on pulsewidth reduction and electronic triggering. The cavity is fed by pulsed-RF source, the resonance is evolved at $t\geq t_{0}$ , $t_{0}=\textrm {cavity}$ filling time. Established standing waves or resonance condition is brokendown by triggered plasma switch programmed with adjustable delay and pulsewidth. This causes the stored energy to be transmitted as shorter output RF-pulse. The implementation of a microwave pulse compression system requires careful measurements and structural modifications to be able to tune design parameters for optimal setup. In the scope of this paper, the experimental results are obtained for different waveguide lengths and various load configurations (to exploit new opportunities). All connections, iris configuration, and precise adjustment of plasma triggering have been set up cautiously. The cavity gain is increased up to 23 dB with trigatron driving improvements. High power requirements and demands are investigated for many applications, particularly for biomedical science projects. [ABSTRACT FROM AUTHOR]

The multigap gas switch has been widely used in liner transformer drivers (LTDs), but there is still room for improvement on its self-breakdown and triggering characteristics. In this paper, based on the circuit model of the six-gap gas switch, the gap voltage distribution during the charging and triggering process is analyzed, and the optimization on self-breakdown and triggering characteristics by mounting resistors and capacitors in parallel with switch gaps are theoretically and experimentally investigated. The results indicate that compared with the original switch, when the self-breakdown voltage is about ±90 kV, the standard deviation is reduced from 7.5 to less than 3 kV; for a charging voltage of ±80 kV and by operating at 60% working coefficient, when the negative trigger voltage is 75 kV, the jitter of the switch is reduced from 6.1 to 1.4 ns. [ABSTRACT FROM AUTHOR]

In this paper, a modular topology is presented for generating high-voltage pulsed power. The proposed structure consists of Marx-type modules, which are based on the switched-capacitor (SC) concept. This module receives an input voltage and, depending on the requirement of the user, produces an output voltage either equal to the input or twice as much as the input voltage, which shows the flexibility of our model. The capability of the module to produce a doubled output makes it appropriate for applications with low input voltage sources. Also, the topology has the capability of generating combined wide and narrow pulses. The topology was simulated in MATLAB Simulink and a laboratory setup was built to test its operation. The results validate the theoretical basis of the structure. [ABSTRACT FROM AUTHOR]

This paper proposed the use of a ringer, a self-switched inductive storage system, for applications involving reluctance accelerators, a kind of electromagnetic launcher, and compatible with applications where portability is a requirement. There will be shown three different useful approximations for the analysis of the ringer, employed as a power source for a reluctance accelerator. First, it described the equations governing the que behavior of an ideal unloaded ringer, and then the equations for the ringer with an uncoupled inductive load, and ultimately a Lagrangian model for the ringer as an inductive power source for a reluctance accelerator, capable to make predictions about the currents through the circuits and the exit speed of the projectile for a given firing. The accuracy of the predictions made with the third approximation, the Lagrangian model, was tested experimentally. [ABSTRACT FROM AUTHOR]

The plasma produced by a pulsed generator is an efficient tool for an airflow control. In this paper, a nanosecond pulsed generator constructed with a fast solid-state switch is designed for triggering synchronous discharges in plasma synthetic jet (PSJ) actuators connected in series. The generator delivers high-voltage pulses with a peak voltage varying from 0 to 20 kV, a rise time of 20 ns, a full-width at half-maximum of 200 ns, and a wide range of pulse-repetition rate varying from 0 to 5.5 kHz. It is proved that this generator is able to trigger synchronous discharges in three PSJ actuators in atmospheric air with a peak discharge current more than 90 A and a deposited energy per pulse of 39 mJ. A schlieren system is used to observe the airflow dynamics, which shows the high synchronization among the three PSJ actuators with a time triggering delay of about 20 ns. The synchronous operation of three PSJ actuators produces a plasma jet with a maximum velocity of 60 m/s and a precursor wave with a velocity of 350 m/s. [ABSTRACT FROM AUTHOR]