Search

A new modular pulsed-power source with fast rise time and step-wise arbitrary output waveform generation is currently under development to drive the Gepulste Elektronenstrahlanlage device investigated at the Institute for Pulsed Power and Microwave Technology (IHM). Acknowledging the complex design procedures necessary to set up a modular pulsed-power source for voltages of up to 120 kV, this paper focuses on the circuit design for a single stage and its validation prior to the generator assembly. Using a semiconductor-based Marx generator topology, the stages are designed to have an output voltage of 1 kV with a pulse current of up to 600 A. When connected to an ohmic load, the measured current rise times are in the order of 46 ns resulting in the current rise rates of up to 10 kA/ $\mu \text{s}$ using the commercial devices. The step-wise arbitrary output waveform is created by generating the switching commands on the stage using a microprocessor and a fast optical synchronization unit. Effective stage shielding is verified by operating the stage in a 100-kV, 2.5-kA electromagnetic interference test bed. This paper presents the design considerations and the corresponding measurements. [ABSTRACT FROM AUTHOR]

In this paper, a new configuration of dielectric-barrier discharge (DBD) reactor with three electrodes was manufactured and used to produce ozone. Designed flatly, this reactor is capable of establishing three different discharge modes from type of the volume and surface discharges, without modifying its internal structure. The aim of presenting this paper is to experimentally analyze the three discharge modes and their combination using a second channel to produce ozone. The two reactor channels are identical in terms of dimensions, material, and manufacturing process. Two frequency-adjustable pulse generators of the same electrical characteristics and two high-voltage transformers were used in the course of the experiments. The applied sinusoidal voltage is from 0 to 12 kVp-p. The frequency range was determined and fixed for all three discharge modes for the highest ozone concentration at a fluctuation rate of 1 L/min. Effects of increasing the applied voltage on the obtained concentration from the three different discharge modes were experimentally analyzed. Using the provided inlets–outlets, the effect of flowing gas through the length and width of the discharge area on ozone concentration was investigated, and appropriate flow directions were determined for the flowing gas under either of the three discharge modes. Experimentally results have been done for this three discharge modes as well as hybrid modes. The maximum ozone production rate achieved up to 14.52 g/h in the series combination of two different volume discharge. At 96% oxygen purity, ozone production yield, in two modes volume discharge VaDBD and surface discharge SDBD, have been improved up to 529.87 g/kWh. However, the total input power of the entire system is 120.2 W. [ABSTRACT FROM AUTHOR]

In this paper, a complete flux scheme (CFS) has been implemented in 1-D fluid model for simulating the pulsed dielectric barrier discharge (DBD) in pure argon at atmospheric pressure. The characteristic quantities of the pulsed DBD have been systematically calculated by using the CFS and presented in comparison with those by using the exponential difference scheme (EDS). This paper shows the following results. There is the two-pulse discharge mode in the present simulation. The two discharge currents obtained using the CFS and EDS converge to the same result in good agreement with the experiment as spatial step length decreases, but the CFS has a fast convergence performance compared to the EDS. With a small grid number, the numerical scheme has an evident effect on the characteristic quantities in the time region corresponding to the first discharge pulse. This paper suggests that in the pulsed DBD, the usage of the CFS with a properly small grid number can give more accurate result and also presents a high calculation efficiency. [ABSTRACT FROM AUTHOR]

The past measurements of the plasma density and potential profiles near the exit of the keeper electrode in a hollow cathode device suggested that turbulent ion acoustic fluctuations and ionization instability in the cathode plume significantly increased the energy of the ions that flow from this region. The lifetime of keeper electrode is limited by sputtering or ion bombardment of the Molybdenum surface exposed to the discharge plasma. Increases in the cathode gas flow reduce the amplitude of the fluctuations and the number and energy of the energetic ions, which decreases the erosion rate of the keeper electrodes. However, as the cathode gas flow is raised for a given discharge current, the performance of a 5-kW Annular-Geometry Ion Engine (AGI-Engine) declines. There is a strong relationship between the performance and the lifetime of the ion thruster. To validate whether the 20-A hollow cathode satisfied China’s communication satellite platform’s application requirement for North-South station keeping, this paper analyzed the effect of the cathode gas flow on the performance and the lifetime of the AGI-Engine. Different from the previous methods, this paper first tracked the movement of energetic ions generated in the plume of the hollow cathode, predicted erosion rates, found where they hit the keeper electrode, and then determined the amount of material that they sputtered. A review of past experimental results was presented first. Next, based on the existing experimental data, theoretical analysis and numerical calculations were performed to determine the optimum gas flow range and the performance curve of the 20-A hollow cathode. The results showed that the primary erosion mechanism of the keeper electrode was caused by impact from Charge Exchange Xenon (CEX) ions, which caused the cathode orifice to be widened and attenuated over time. However, heavy double xenon ($\text{X}_{\text{e}}^{++}$) ions, which struck the keeper electrode more severely than CEX ions, were the most crucial factor that limited the lifetime of the 20-A hollow cathode due to their high energy and large mass. [ABSTRACT FROM AUTHOR]

This paper presents a self-consistent model of plasma polarization around an isolated micrometer-sized dust particle being under the action of an external electric field. It describes ion focusing and wake formation for dust particles with different radii and external electric fields. It is shown that despite the formation of wake, plasma maintains a quasi-neutral condition around a negatively charged dust particle, and the volume charge formed as a result screens the dust particle completely. It is also shown that in the external electric field, the dipole moment of the part of the ion nearest to the dust particle is proportional to the dust particle charge. As the external electric field increases and reaches some threshold value, a positive peak appears in plasma potential downstream of the dust particle. It then increases linearly and shows a broad maximum. [ABSTRACT FROM AUTHOR]

Melamine formaldehyde microspheres are widely used in dusty plasma experiments for their monodispersity, sphericity, low mass density, and well defined sizes. This paper summarizes problems that were encountered in numerous applications of these grains in different laboratory simulations. and the already published results are discussed in view of new experiments. The main results of this paper are connected with changes of the grain mass due to the decreased pressure and/or increased temperature and variations of the grain dimensions, its shape, and mass density under electron or ion bombardments. By contrast to the work function estimated from field emission properties, we have found the photoelectric work function (4.5 eV) being close to that expected. A sputtering of the grains using a 30-keV ion beam revealed their unexpected heterogeneity. [ABSTRACT FROM AUTHOR]

The front plates and embedded particle sensor shells that are part of the electric field instrument (EFI) on the Swarm satellites have recently been used as planar Langmuir probes, as an additional diagnostic tool to infer environment parameters. The interpretation of measured currents in terms of the plasma density or incoming flow speed, however, requires a knowledge of the front plate effective cross section $A_{\textrm {eff}}$. Measurements made under various space plasma conditions have led to the conclusion that this cross section is generally larger than the known geometrical cross section $A_{\textrm {geo}}$. Interpretations of measurements have thus been made using fixed relative enhancements of $A_{\textrm {geo}}$ ranging from 8% to 17%. In this paper, results from kinetic simulations are presented, from which the effective cross section can be determined over a range of plasma parameters. These are used to shed light on the physical mechanisms responsible for this enhancement and construct an empirical fit to the relative enhancement $\delta $ , where $A_{\textrm {eff}} = A_{\textrm {geo}}(1 + \delta)$ , and, in turn, enable improvements in the accuracy of inferred plasma parameters. [ABSTRACT FROM AUTHOR]

A single-phase tubular permanent magnet linear generator (TPMLG) with a novel structure for Stirling engines is presented in this paper. TPMLG can directly convert mechanical energy into electrical energy and it is the main energy conversion device in Stirling power generation system. Its 3-D geometry and initial dimensions are given in detail. Due to the structural characteristic, the finite element (FE) method (FEM) is used to analyze the electromagnetic field. An FE model is established from the magnetic field perspective. Isolines of magnetic vector potential can be obtained, as TPMLG locates at −0.015, 0, and 0.015 m. The dynamic performances of TPMLG under different reciprocating frequencies are compared and analyzed. Compared with three different kinds of machines, it can be concluded that the proposed TPMLG can produce electricity with less weight and materials. [ABSTRACT FROM AUTHOR]

The interest in the use of atmospheric-pressure plasma jets (APPJs) is constantly growing. APPJs offer various ranges for applications, such as wound healing, cancer treatment, and dental care. The complex plasma chemistry plays an important role in each of these fields but is often poorly understood. In this paper, the production of atomic oxygen in a radio frequency helium–oxygen plasma is investigated by means of a numerical simulation. A 1-D discharge of an atmospheric-pressure plasma jet is created with the plasma module of COMSOL Multiphysics, using a set of 25 reactions. Many 1-D simulations usually cannot estimate the power deposition in a correct way because of suspected arising losses, such as radiation and inefficiencies of the external circuit. In order to match the experimental power deposition of 13 W, high voltages (855 V) are required in the model. Such high voltages cause changes in the plasma characteristics like a switch in the glow mode. The impact of the voltage on the plasma is investigated by the comparison of a low-voltage (325 V) simulation, which matches the experimental oxygen production, and a high-voltage (855 V) simulation, which matches the experimental power deposition. Outcomes of this paper further support the idea that the power deposition measured in experiments is higher than the actual power deposition coupled to the plasma. [ABSTRACT FROM AUTHOR]

The planned China fusion engineering test reactor (CFETR) needs one or more negative-ion-based neutral beam injectors (N-NBIs) with a beam energy of 500 or even 1000 keV. In order to prepare for CFETR, a prototype of CFETR N-NBI is being designed. The prototype needs an acceleration grid power supply (AGPS) rated at 200 kV/25 A with a maximum pulselength reaches to 3600 s. The AGPS adopted a single-stage inverter-type high-voltage power supply (HVPS). The output voltage ripple is an important specification of the AGPS, which can affect the efficiency and stability of N-NBI system by influencing the beam divergence. However, the conventional methods cannot be used to limit the output voltage ripple of the inverter-type HVPS used as AGPS of CFETR N-NBI prototype. This paper simplified the AGPS to an insulated three-phase three-level (TPTL) dc–dc converter connected with a dual dc link. The working process of the TPTL dc–dc converter with duty-cycle modulation has been analyzed, and two main continuous conduction modes are described. The influence of key parameters such as duty cycle of inverter, leakage inductance of transformer, and output current on output voltage ripple is analyzed. Based on the analysis results, a so-called combined control strategy was proposed to keep the output voltage ripple at a level. The proposed strategy is suitable for the cases where the object output voltage is below 175 kV. Some simulations were carried out by using MATLAB/Simulink. The results showed that the analysis in this paper is reliable and the proposed control strategy has a good performance. [ABSTRACT FROM AUTHOR]

We have studied the two-electron pseudodot (TEPD) system immersed in plasma environments under the influence of a monochromatic linearly polarized laser field. The four different sets, constituted by the potential parameters, of the more general exponential cosine screened Coulomb potential are used to characterize the Debye and quantum plasma environments. The time dependent in the Schrödinger equation arising from the laser field is interchanged to the potential energy term from the kinetic energy term through the dipole approximation and the Kramers–Henneberger transformation. Then, the laser-dressed potential that denotes the effects of the laser radiation field is constituted by using the Ehlotzky approximation. In that case, as the analytical solution is impossible just now due to the complicated form of the Schrödinger equation, the numerical solution is carried out via the asymptotic iteration method. In this paper, the pseudodot system is considered because the quantum dots are very similar to atomic systems, and the pseudoharmonic potential is successful in explaining the atomistic structures. However, it is an important motivation for us that, as well as the importance of the laser–plasma interactions, the laser field is a considerable exciter for radiating, which exhibits remarkable confinement effects. Since, as well as the screening effects exhibited by plasmas on atomic systems, and their significant results, the plasma is a significant experimental argument in manufacturing and modification of the quantum dots, the plasma effects are taken into consideration in this paper. Within these motivations, all parameters that operate on the energies of TEPD system with the laser effect in plasmas are analyzed in detail, and the corresponding results are discussed thoroughly. [ABSTRACT FROM AUTHOR]

Paschen’s law gives the inception voltage for an electrical discharge as a function of the product of gas pressure and the gap distance between the two infinite planar electrodes. It is known that the deviations from Paschen’s law occur when the temperature is increased. Historically, two theoretical corrections, the Peek and Dumbar corrections, are proposed to predict the deviation from Paschen’s law by increasing the temperature. To carry out an experimental investigation on the deviation from Paschen’s law by increasing the temperature, a customized system was designed, which can operate at temperatures up to 400 °C and at pressure up to 1 MPa, calculated at room temperature, with an interelectrode distance between $100~\mu \text{m}$ and 6.6 mm and an error on the interelectrode distance measurement of $20~\mu \text{m}$. In this paper, first, the results from the experimental investigation on the deviation from Paschen’s law at temperature up to 400 °C are presented. The results are then compared with theoretical corrections, and finally, a theory to explain the results is proposed and discussed. [ABSTRACT FROM AUTHOR]

The collision frequencies between electrons and air molecules are important parameters when analyzing electrical breakdown. Different values for the collision frequency in atmospheric air have been reported in academic literature; the current analysis method for breakdown in waveguides and filters considers an electric field-independent term. However, some authors have remarked the importance of an electric field dependence of the collision frequency. In this paper, the collision frequency of electrons, accelerated by the presence of an electric field, against air molecules is obtained. The collision frequency is calculated from experimental data, for breakdown voltages at dc in positive polarity in a wide atmospheric pressure range using a plane–plane plates configuration. As waveguide filters are currently designed with a 3-dB tolerance below the electrical breakdown thresholds, this paper analyses the current methods for these breakdown threshold calculations, and proposes a novel correction factor for the collision frequency in order to approximate the analytic calculations to experimental results. [ABSTRACT FROM AUTHOR]

This paper embodies the results of experimental studies of a dielectric barrier discharge low-temperature nonequilibrium plasma reactor that runs in air and nitrogen at atmospheric-pressure conceived for surface treatment applications. A homemade reactor, of typical plane-to-plane geometry with the dielectric covering the upper electrode which is stressed by a high voltage (40 kV, 3–20 kHz) is used. Electrical signals (current and voltage), optical emission spectroscopy records, and total light emission measured by photomultiplier have been analyzed and used to distinguish different plasma regimes which are studied for the treatment of a lignocellulosic material (sugarcane bagasse). In the filamentary discharge regime, the gas temperature of few tens of degree Celsius above the ambient one was determined, the electronic temperature of some electronvolts and electron density in the range of 1012–1013 cm−3 were estimated. Plasma treated pellets of sugarcane bagasse were analyzed by diffuse reflectance infrared Fourier transform spectrometry and the relative results obtained under filamentary discharge regime have shown significant degradation of the lignin macromolecule. It has been shown important modifications on the lignocellulosic material, namely, the plasma attacks drastically the lignin bonds. Strong modification of lignin was observed near wavenumber of 3400 cm−1, due to stretching vibrations of OH, and for the band 1114 cm−1 which is related to C=C and C=O stretching. Severe decrease of the band intensity 1596 cm−1, which due to C=C stretching and C=O, is also a result of the treatments done in this paper. [ABSTRACT FROM AUTHOR]

This paper outlines the requirements for a source of buffer plasma, which is necessary for elaboration of plasma separation method of substances and following foundations development of plasma reprocessing technology of spent nuclear fuel and radioactive waste. Such source is implemented on the basis of a helicon discharge, allowing plasma generation in a cylindrical volume with characteristic dimensions on the order of 1 m and bounded by metal walls. At plasma-forming gas (argon) pressure of 1 mTorr, radial profiles of density $n_{e}$ and temperature $T_{e}$ of electrons were obtained for various magnetic field magnitudes (0–200 G) and RF power (up to 6 kW) using double probe and optical methods. The typical value of $T_{e}$ amounted to eV units and $n_{e}$ was about 1012 cm−3. [ABSTRACT FROM AUTHOR]

Photoelectric characteristics are an important reference for high-voltage discharges and are closely related to the excited mode of the high-voltage source. In this paper, we built a large-scale volume dielectric barrier discharge (DBD) system, which is composed of multilayer parallel-plate DBD electrodes and is excited by a high-voltage source in the power density modulation (PDM) mode. Subsequently, we analyzed the applied energy equation and evaluated the DBD systems photoelectric characteristics. The results show that the energy values of different applied voltage cycles during a PDM period exhibit significant differences. However, the average energy in a PDM period is approximately constant. Moreover, the equivalent capacitance of the DBD cell is a function of both the applied voltage and energy density. For the DBD cell, with the increase in both the applied voltage and energy loaded on the DBD cell, the total equivalent capacitance ($C$) is approximately constant, the dielectric capacitance ($C_{\mathrm{ d}}$) increases exponentially and decreases linearly, while the discharge gap capacitance ($C_{\mathrm{ g}}$) decreases and increases in the same cases. In addition, the relative intensities of the discharge emission increase and the energy efficiency ratios of the relative photoquantum yield of active species decline with the increase in both the applied voltage and energy density loaded on the DBD cell. The experimental results have been analyzed by evaluating the influence of the electrical parameters, and the underlying physical principles have been discussed. This paper clearly demonstrates that the photoelectric characteristics of the DBD reactor are significantly influenced by both the applied voltage and energy density, thus providing helpful insights into the energy evaluation and application of high-voltage discharges. [ABSTRACT FROM AUTHOR]

The challenging demands of pulsed electron beam devices (such as the GESA device) with respect to their pulsed power supply have led to the development of a new semiconductor-based Marx generator. At a maximum output voltage of 120 kV and 600-A pulse current for a duration of up to 100 $\mu \text{S}$ , stepwise arbitrary output waveforms are desired. A fast rise time of the generator is achieved by using fast switching circuitry, low inductance capacitors, and a low inductance stage arrangement. For low jitter triggering of all stages and efficient signal transmission, the generator uses an optical bus system for communication. Due to the inherent dynamic load characteristics of the GESA device, the generator features a fast overcurrent protection scheme. This paper presents selected design aspects of the generator and their validation in a small-scale assembly able of delivering up to 8 kV at 600-A load current. [ABSTRACT FROM AUTHOR]

This paper discusses the design and electromagnetic analysis of an induction-type coilgun system with a pulse power module. The voltage, current, force, velocity, acceleration, and efficiency of the coilgun system were analyzed using the finite-element method (FEM). A simplified FEM model was developed for ensuring both accuracy and rapid calculation times. Based on the results of the electromagnetic analysis, the geometry of the coilgun system was defined with the Taguchi method. The coil-type armature was applied for increasing the mutual inductance and projectile force. The electromagnetic analysis results were also compared with the analytical analysis results. The designed coilgun system was found to exhibit high energy efficiency and safety of the system. The design specifications and analysis results concerning the coilgun can, hence, be effectively utilized to develop a large-scale multistage induction-type coilgun system. [ABSTRACT FROM AUTHOR]

Nanosecond and subnanosecond high-voltage pulses have used in new biological applications, such as cancer treatment using an ultrashort pulsed high electric field. For this treatment, the use of high-power pulsed electromagnetic wave has been proposed to obtain the required high electric field. This paper focuses on the design of a compact high-power pulsed electromagnetic wave generator using a nanosecond pulsed power generator for cancer treatment. We developed a pulsed power generator that continuously outputs multiple pulses via a nonlinear transmission line (NLTL) using magnetic switches. The NLTL comprises a ladder of capacitors and saturable inductors. The NLTL generates a pulse train by delaying the propagation of the pulse using the magnetic switch of each ladder. The frequency of repetition of the burst pulse is 13.8 MHz. The peak output voltage is 7 kV at the maximum input voltage of 28 kV. The number of pulses in the pulse train can be varied by the number of units of the magnetic switch. [ABSTRACT FROM AUTHOR]

This paper is dedicated to the characterization of internal charging and discharging processes of different systems or materials in medium earth orbit (MEO) environment. Experiments for MEO were carried out at the ONERA, Toulouse, France, using the Geostationary Dielectric Unit Radiation electron beam facilities. Assuming 2.5 mm of Al shielding on the spacecraft, a worst case electron spectrum emerging from the shielding has been calculated from previous works. Different materials or systems have been tested in this configuration: printed circuit board (PCB) and insulating materials used for cables or connectors [polyetheretherketone, ethylene tetrafluoroethylene (ETFE), and Kapton]. The experiments revealed that PCB or ETFE cables might be prone to present a high risk of charging and discharging after several days under extreme environment. Electrostatic discharges have then been detected on PCBs. An experimental and numerical method has also been defined and validated at ONERA to assess the charging levels in long-term space environment through short-duration experiments performed at higher electron current. This method requires the extraction of electric parameters (especially radiation-induced conductivity) of the tested materials. From these parameters, it was demonstrated that the extrapolation of the experimental results was feasible for most space used materials. [ABSTRACT FROM AUTHOR]

Studies have been taken into the breakdown voltage jitter of corona-stabilized switch at high repetition rate up to several kHz. It is thought that the gas recovery affect the jitter of breakdown voltage directly at high repetition rate, because the gas switch will breakdown at a low voltage if the gas cannot fully recover. The breakdown voltage jitter is called voltage jitter in the following paper. However, based on the experimental results, the voltage jitter still exists at low repetition rate, even at single-shot mode. This is not explained by the previous studies. In this paper, voltage jitter below 100 Hz of a corona-stabilized switch is investigated experimentally. A corona-stabilized switch is introduced, using a cylindrical electrode as the cathode and a plane electrode as the anode. The gas used between the electrodes is SF6. A negative pulse with a maximum width of 30~\mu \texts is used to charge this switch. The tested factors include gas pressure, gap space, repetition rate, and switch geometry. Experimental results show that voltage jitter is mainly affected by the gas pressure and switch geometry. It is seen that voltage jitter decreases as gas pressure increases and a suitable cathode geometry presents a low voltage jitter. Critical volume is a region close to the highly stressed electrode, where the presence of an electron will lead to an electron avalanche which attains a critical size and hence leads to a stabilizing corona. Critical volume is introduced to explain the experimental results. It is found that less voltage jitter can be achieved with a smaller and more concentrated critical volume, as well as efficient corona stabilization. The results indicate that voltage jitter may be reduced by optimize the critical volume at low repetition rate. [ABSTRACT FROM PUBLISHER]

Bipolar junction transistors (BJTs) have been widely studied and used in nanosecond high-voltage pulse generators due to the advantages of fast switching speed and high repetitive frequency. Usually the Marx-type circuit is used to raise the peak value of output pulses. In this paper, a traditional BJT-Marx circuit using charging resistors is analyzed theoretically and experimentally. Based on the results, the structure of a circuit is changed to decrease the isolation voltage across the resistors, and diodes are used to replace charging resistors to block capacitors discharging to resistors. Experimental results showed that the three Marx generators proposed in this paper output pulses with higher voltage amplitude, and the last improved circuit outputs pulses with faster fall times at a higher efficiency. [ABSTRACT FROM AUTHOR]

This paper demonstrates for the first time the use of microplasma to perform AND, OR, and XOR logic operations. The logic circuits are implemented similar to diode-resistor logic. Output voltages are in the range of \(5-40\) V and can be modified by varying the load resistor. The active area of the microplasma device is just \(50~\mu \) m \(\times 5~\mu \) m. The small interelectrode gap kept breakdown voltage to \(\sim 250\) V when operated in He gas at atmospheric pressure. The use of plasma as a source of free carriers is also demonstrated, with free carriers available up to 500- \(\mu \) m away from plasma. [ABSTRACT FROM PUBLISHER]

Polymers are widely used on spacecraft for different specific functions such as thermal and electrical insulation, mechanical support, and adhesion. These polymers are highly sensitive to radiation encountered in space. Their electric properties are especially significantly altered leading to a very specific behavior in terms of charge transport and discharge processes. Different dedicated facilities have been developed at ONERA, with Centre National d’Etudes Spatiales support, for the characterization of space used materials in representative conditions. Thanks to the use of these different facilities, it has indeed been demonstrated that radiation-induced conductivity of space polymers strongly affects the charging surface potential and depends on several parameters (radiation dose rate, total radiation dose, temperature, and on the induced electric field) through complex physical mechanisms that are described in this paper. The sensitivity of polymers on these different parameters strongly depends on the polymer trap distribution and molecular configuration. Experimental and numerical results are presented in this paper, coupled with the different experimental techniques developed and applied to this work. [ABSTRACT FROM PUBLISHER]

Charging effects in space are widely dominated by intrinsic and radiation-induced conductivities (RICs) of the irradiated materials. These data are needed by the community to perform charging predictions for assigned missions. This paper was dedicated to the characterization of bulk conductivity and RIC of polymers, ceramics, and glasses and their evolution in regard to sample reproducibility, composition, structure variation, and environmental conditions, such as radiation dose rate, temperature, and electric field. Three different polymers have been tested in this paper: 1) fluorinated ethylene propylene; 2) PolyEther Ether Ketone; and 3) Ethylene TetraFluoroEthylene. Three nonpolymer materials have been tested as well: two borosilicate glasses and aluminum oxide Al2O3. The major objective was, for polymers, to understand physical variations of conductivity for similar materials and, for nonpolymers, to get better knowledge on the main physical contributions steering bulk conductivity and RIC at low temperature. [ABSTRACT FROM PUBLISHER]

Air circuit breaker (ACB) is widely used in power distribution system. The movable contact of ACB consists of multiple parallel contacts and the arc will be ignited between arcing contact and static contact when the short-circuit current appears. This paper focuses on the arc evolution process at various currents in multiple parallel contact systems. A 3-D magnetohydrodynamic model of a multiple parallel contact structures is developed. In this model, the anode consists to five parallel contacts, and they are separated by insulation material. The near-electrode layer with a nonlinear voltage–current density characteristic is modeled to describe the near-electrode voltage drop, and the difference between near-anode and near-cathode layers is considered. The magnetic vector potential approach is adopted to calculate the time-varying electromagnetic field produced by the current loop. The arc evolution processes at various currents are analyzed by current density and arc voltage. It is noted that the anode arc root appears on multiple contacts with the increase of current. The arc evolution process mainly depends on the arc resistance characteristic. [ABSTRACT FROM AUTHOR]

This paper examined the extent of the dependence of the interrupting capability on the shape of the contact system in a molded case circuit breaker (MCCB). Thus, a simple analysis method was suggested for estimating the interrupting capability and used to investigate the magnetic flux density distribution in a contact system caused by a short-circuit current. However, the MCCB produced by a joint-research company turned out to have the poor interrupting capability and a low magnetic flux density distribution for driving arc plasma between two contacts in the contact system. To build up additional interrupting capability without making many changes, a new arc runner was devised to prevent arc plasma from returning to its original position in the contact system. The arc voltage characteristics were tested with a simplified synthetic testing facility using an LC resonant circuit. The result showed that the new MCCB had a much higher arc voltage than the existing MCCB. This implies that investigating the arc voltage is fairly comparable to predicting the arc plasma extinction and the interrupting capability. [ABSTRACT FROM AUTHOR]

Temperature field simulation for self-healing power capacitor makes sense to the capacitor optimization and improvement of capacitor’s rated voltage and capacity. On the basis of reasonable simplifications and assumptions for capacitor structure, a 3-D temperature field numerical simulation model for a self-healing power capacitor is formulated in Fluent 15.0. The ambient temperature is set to 55 °C, and the applied voltage is ac 400 V. The temperature distributions of the shell and core of the self-healing capacitor are obtained. The results reveal that the temperature of the core is 2 °C–3 °C higher than that of the shell. The highest temperature of the shell locates on the large side surface, and the temperature of the large side surface is higher than that of the small side surface. To validate the above simulation, a self-healing capacitor is manufactured and thermal resistance sensors are used to measure the temperature in the thermal stability test. The simulation is validated by the experiment. Finally, the influences of the ambient temperature and applied voltage on the temperature rise are investigated. This paper can be taken a reference to the self-healing capacitor operation, maintenance, and even the optimization of its internal structure and material. [ABSTRACT FROM PUBLISHER]

In recent years, all solid-state Marx generators have been found more and more extensive applications in industrial, environmental, and biological fields. All solid-state Marx generators have many requirements for their drive circuits, such as good synchrony for driving signals at different stages, fine isolation between control signals and the main circuits, adjustable pulsewidths and frequencies, and good driving abilities. This paper proposes a high-performance drive circuit for a 24-stage Marx generator based on IGBTs. A half-bridge circuit using IR2110 outputs a high-current turning-on drive signal (positive) and a turning-off drive signal (negative) with adjustable dead time. The control drivers are input to the common primary side of 24 nanocrystalline magnetic transformers, which isolate the control circuit and the main circuit. Through gate circuits at the second sides of the magnetic cores, the turning-on drive signal charges 24 gate–emitter capacitors to required voltages and consequently all IGBTs move into on state until the turning-off signal arrives. Similarly, the negative turning-off drive signal charges all gate–emitter capacitors to a negative voltage which ensures all IGBTs stay in the off state. Therefore, the pulsewidth is determined by the phase difference between the turning-on and turning-off drive signals. Equipped with this drive circuit, the 24-stage Marx generator is able to produce stable high voltage pulse with a peak value of −9.6 kV, PRF $0.05\sim 5$ kHz, and different pulsewidths. In this paper, the design details and experimental confirmation of the proposed drive circuit are illustrated. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach to test surface material charging under electron flux representative of space conditions below 400 keV. The experimental protocol used to test space material electrical properties consists in adapting the electron flux distribution to mimic worst case spectra met in space. Input environments are taken from Kp > 5 specifications at geosynchronous orbit (GEO) and from the analysis of both RBSP and LANL spacecraft data at middle Earth orbit (MEO) and GEO. Experimental results using GEO specifications show that the surface potential strongly depends on the energetic particle flux. Above a given > 100-keV electron flux, the radiation-induced conductivity tends to govern the charging dynamics. A numerical analysis based on the environments selected in this paper shows that charging levels could be larger at MEO than at GEO. [ABSTRACT FROM AUTHOR]

Data from the Magnetospheric Multiscale (MMS) mission, in particular, the spacecraft potential measured with and without the ion beams of the active spacecraft potential control (ASPOC) instruments, plasma electron moments, and the electric field, have been employed for an improved determination of plasma density based on spacecraft potential. The known technique to derive plasma density from spacecraft potential sees the spacecraft behaving as a plasma probe which adopts a potential at which the ambient plasma current and one of photoelectrons produced at the surface and leaving into space are in equilibrium. Thus, the potential is a function of the plasma current, and plasma density can be determined using measurements or assumptions on plasma temperature. This method is especially useful during periods when the plasma instruments are not in operation or when spacecraft potential data have significantly higher time resolution than particle detectors. However, the applicable current–voltage characteristic of the spacecraft has to be known with high accuracy, particularly when the potential is actively controlled and shows only minor residual variations. This paper demonstrates recent refinements of the density determination coming from: 1) the reduction of artifacts in the potential data due to the geometry of the spinning spacecraft and due to effects of the ambient electric field on the potential measurements and 2) a calibration of the plasma current to the spacecraft surfaces which is only possible by comparison with the variable currents from the ion beams of ASPOC. The results are discussed, and plasma densities determined by this method are shown in comparison with measurements by the Fast Plasma Instrument (FPI) for some intervals of the MMS mission. [ABSTRACT FROM AUTHOR]

Surface charge accumulation on polymer insulating material has been recognized as an important factor for electric field distortion that results in reduction of surface flashover voltage. This paper reports on the charge accumulation behavior between a pair of finger-shaped electrodes on epoxy/Al2O3 nanocomposites under dc voltage superimposed by repetitive pulses. The charge distribution was measured by means of an electrostatic voltmeter, from which the average charge density could be calculated. Effects of dc voltage, nanofiller content, and pulse voltage on charge accumulation behavior were investigated. Obtained results showed that with the increase in the filler content from 0 wt% to 5 wt%, the average charge density increased initially then appeared to decrease. The superposition of repetitive pulses on dc voltage led to a remarkable growth in charge accumulation as compared with that when only dc voltage was applied. It is suggested that the charges are originated from local gaseous ionization and/or electrode injection, which is determined by the combined voltage. The charge density is dependent upon the surface trap, which is affected by nanofiller content. The superposition of repetitive pulse is considered as a possible reason to encourage local gaseous ionization that results in enhanced accumulation of surface charge. [ABSTRACT FROM AUTHOR]

The multigap gas switch has been widely used in liner transformer drivers (LTDs), but there is still room for improvement on its self-breakdown and triggering characteristics. In this paper, based on the circuit model of the six-gap gas switch, the gap voltage distribution during the charging and triggering process is analyzed, and the optimization on self-breakdown and triggering characteristics by mounting resistors and capacitors in parallel with switch gaps are theoretically and experimentally investigated. The results indicate that compared with the original switch, when the self-breakdown voltage is about ±90 kV, the standard deviation is reduced from 7.5 to less than 3 kV; for a charging voltage of ±80 kV and by operating at 60% working coefficient, when the negative trigger voltage is 75 kV, the jitter of the switch is reduced from 6.1 to 1.4 ns. [ABSTRACT FROM AUTHOR]

Induction synchrotron (IS) has become the focus of improving the intensity of high energy ion beams in recent years. But because of the pulse voltage of the induction accelerating cell cannot adjust quickly, causing the mismatch of the magnetic deflection field and accelerate electric field, there is a serious beam loss problem in IS. The simulation of beams longitude dynamics proves that increasing the number of accelerating cells can effectively reduce the loss. In this paper, a novel compact induction accelerator module is introduced. Compared with the existing induction accelerator module of KEK, the new design can increase the number of accelerating cells to more than five times in the same installation space and improves the voltage top drop of the acceleration pulse significantly. [ABSTRACT FROM AUTHOR]

The multipactor (MP) phenomenon can generate exponentially increasing electron populations in RF vacuum systems, leading to components becoming damaged. This paper uses numerical methods to analyze an RF vacuum window in a coaxial line under various standing wave conditions. Our methods are first benchmarked against the analytic and experimental results for the traveling wave and the numerical results for standing waves that were found in previous work. Second, the effect of standing waves on electron motion in the axial direction is discussed and related to electron trajectories in the presence of an RF window. It is found that standing waves with the magnetic maximum located behind the RF window lead to window collisions that can affect MP depending on the power, frequency, and conductor radii. For a low number of window collisions, MP was highly predictable by earlier work, but as the percentage of collisions occurring on the window surpassed approximately 50%, a novel mode of MP emerged to dominate the phenomenon. [ABSTRACT FROM AUTHOR]

This paper presents the numerical simulation results of characteristics and efficiency of separation of uranium ion fluxes and its fission products in the process of the plasma separation. The movement of beams of heavy (238 u) and light (160 u) single-charged ions in vacuum and in helium buffer plasma has been investigated at a pressure of 10 mtorr, magnetic fields 0.8–1.2 kG and electrical potentials up to 1 kV. The interaction between the ion beams and their interaction with the buffer plasma has been taken into account. The numerical simulation of plasma has been conducted in a drift–diffusion approximation. It has been shown that the presence of buffer plasma in the area of ion fluxes and occurring compensation of their space charge can greatly improve the separation efficiency compared to the separation of ion fluxes in vacuum. [ABSTRACT FROM AUTHOR]

Sliding electrical contact between rail and armature in rail launchers is characterized by high speed and large current. Melt erosion is caused by the current concentration on the contact surface of armature. This current melt erosion (CME) has been experimentally studied in the current range of 10–20 kA/mm with a 20-mm caliber lab-scale rail launcher, and payload separated method was used to keep the recovered armatures intact. Thus, the onset behavior and erosion patterns of CME can be successfully observed in such relatively low current densities. In this paper, we will further our study to analyze the patterns of CME with the increasing current densities under the effect of different initial mechanical contact force. Results show that CME all start at the side edge, and then spreading longitudinally and transversely with the increase of current. It is found that the starting position of CME appears near the trailing edge at small mechanical contact force and moves to the leading edge with larger mechanical contact force. At the same current magnitude, erosion amounts are much more under small mechanical contact force. Stationary mechanical contact pressures and current distribution of armature surface are simulated to investigate the effect of initial mechanical contact force on starting position of CME. Current distributes at the edges of actual contact zone and the maximum of current density appears at the side edges of armature. As the initial mechanical contact force increases, actual contact zone and current density move toward to the leading edge from trailing edge. It can be confirmed that the erosion starting position is at the side edge along actual contact zone and will move toward to the leading edge from trailing edge with the increase of initial mechanical contact force. Smaller initial mechanical contact force will cause more erosion at the same current magnitude because of larger current density. Furthermore, an average friction coefficient calculation method is proposed to evaluate the melt lubrication effect of CME. The result shows that the lubrication effect becomes better with larger current densities. [ABSTRACT FROM AUTHOR]

Low-temperature plasma ion mobility spectrometry (LTP-IMS) is the method to identify some materials by measuring concentration of gas phase ions. IMS used in a wide range of laboratory-based biomedical research studies. A nanosecond pulse generator is necessary for LTP-IMS apparatus to enable direct analysis of various chemical compounds without having to evaporate the analyte or seek a solvent or any reagent. In this paper, a dual Marx pulsed generator for LTP-IMS Ionization power supply is proposed based on a new combination of some solid-state switches including insulated gate bipolar transistor (IGBT) and avalanche bipolar junction transistors (BJTs). The compact dual Marx generator is composed of a series of avalanche BJTs and an IGBT as the trigger switch, where its rise time is reduced from 100 to 5 ns by using an avalanche BJT in its command circuit. In this way, a controllable high-voltage pulse generator has designed, built, and tested. The proposed circuit can be used to generate the repetitive high-voltage pulses necessary for low temperature ionization in advanced IMS apparatus. The output voltage has an amplitude of up to 6 kV with pulse widths in the range of 40–1000 ns and pulse repetition rates up to 2 kHz, having rise time and fall time less than 10 ns independent of the load specifications. [ABSTRACT FROM AUTHOR]

In this paper, we designed an active coupling trigger circuit and an active surge protection gap (ASPG). The surge protection level of the passive SPG is improved, and the operating time of the passive SPG is shortened. The equivalent circuits for the coupling trigger circuit were developed. Then, we analyzed the component transient voltage of the active coupling trigger circuit with the combination wave injected. We obtained the numerical relationship between the coupling trigger current and the current flowing through the ASPG. In addition, the timing relationship between the component voltage and the current was acquired. To verify the analysis results, we established the combination wave generator and conducted an experiment. In the experiment, we observed that the trigger circuit operating time and the ASPG impulse breakdown voltage changed with the capacitor charging voltage of the combination wave generator. Furthermore, we discovered the change laws. The results also show that the operating time and impulse breakdown voltage of the ASPG are both smaller than the passive SPG. These results provide an important theoretical and experimental basis for the further study and structural optimization of the ASPG. [ABSTRACT FROM AUTHOR]

When the pressure and temperature of a fluid exceed a critical point, the fluid enters into the supercritical (SC) region. In this region, the physical properties are believed to be in favor of a good current interruption medium. This paper focuses on the arc voltage characteristics of nitrogen arcs burning inside cylindrical tubes at different filling pressures: 1, 20, 40, and 80 bar, thus covering the SC region. Two different tube materials have been used in the experiments, alumina and polytetrafluoroethylene. Arc voltages are measured for arcs burning inside tubes of 2, 4, 8, and 15 mm inner diameters. In addition, free-burning arcs have been investigated at the same filling pressures. The arc current was 150 A at 350 Hz throughout the study. The arc voltage is found to increase with decreasing inner diameter of the tube at atmospheric pressure. At higher filling pressures (i.e., 20, 40, and 80 bar), however, such a simple relationship is not observed. The arc temperature and radius have been calculated based on the “simple theory of free-burning arcs” and the “two-zone ablation arc model.” The calculated arc radius decreases with increasing gas pressure. Furthermore, due to increased absorption of radiation at high filling pressures, ablation is found less significant for ultrahigh-pressure nitrogen arcs compared to atmospheric pressure arcs. This is in line with the observations from optical micrographs of the inner surfaces of the tubes exposed to arcs at different filling pressures. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

The Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP), is in charge of the manufacturing and testing of the 60 high-temperature superconducting current lead series to be completed at the end of 2020 for the International Thermonuclear Experimental Reactor (ITER). This paper first summarizes the testing items and testing results of the ITER lead prototypes in 2015/2016, then, based on the prototypes experiences, discuss the final test piping and instrument diagram for the ITER lead series production testing. A new 5-K test platform to expedite the series testing is also introduced, and a new feature, the 30-kV high-voltage (HV) class insulation for the cryogenic temperature and voltage measurements to allow in situ HV testing, is introduced. The detailed test procedures and test items for the series are discussed finally. [ABSTRACT FROM AUTHOR]

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

Electromagnetic disturbance in the course of rail-gun launching has great influence on the launching process and staff. Based on the magnetic force measured at the startup acceleration and separation stages, the corresponding magnetic field can be calculated. The magnetic field at different positions and heights near the rail gun is analyzed and compared. The results show that the position of the armature has great influence on the magnetic field. The maximum value of the instantaneous magnetic field should be located in the middle of the rail gun. At the same position, the magnetic field decays rapidly with the increase of height. The electromotive force waveforms are analyzed by using the wavelet transform; the analysis shows that the wavelet transform can reveal the time-frequency energy distribution of the electromotive force more accurately and clearly. The research of this paper has a guiding significance to the shielding design of magnetic field of the electromagnetic rail gun, and will promote the development of rail guns. [ABSTRACT FROM AUTHOR]

Due to its low-loss and high dielectric strength, polypropylene is widely used as electrical insulation material in pulse capacitors. In order to study its breakdown characteristics for nanosecond voltage pulses, an experimental setup was designed to generate voltage pulses with a 10%–90% rise time of 38 ns and a full width at half maximum of about 90 ns. Tests of the three polypropylene films with thicknesses of 12, 15, and $18~\mu \text{m}$ were performed. In addition, hundreds of nanoseconds pulse and dc voltage were also applied for comparison. The experimental results reveal that most of the breakdown occurs during the front edge of the pulse for tens of nanoseconds pulse, and the breakdown strengths of the three kinds of polypropylene films are almost identical for different applied voltages, which show a weak correlation between the thickness of the dielectric and the breakdown field. The expected breakdown strength of tens of nanoseconds pulse defined in this paper is not significantly higher than the mean value of the hundreds of nanoseconds pulse and the dc condition, suggesting that the breakdown of a thin polypropylene film is mainly determined by the electrical field but not the voltage-time cumulative effect. All these observations strengthen the conclusion that the breakdown of a thin polypropylene film is an intrinsic phenomenon. [ABSTRACT FROM AUTHOR]

This paper presents the results of predictive calculations of the parameters of pulses of soft X-ray radiation (SXR) on a four-module electrophysical facility GAMMA-4 (the current pulse amplitude is ~3 MA with rise time of ~60 ns) that has been constructed in Russia. Scaling numerical simulation of implosion of a cylindrical single and nested multiwire array in 0-D, 2-D, and 3-D radiation magnetohydrodynamic– approximations is performed, taking into account, the updated double-loop equivalent electrical circuit of the GAMMA-4. The main purpose of the conducted studies was the numerical optimization of the multiwire array parameters to obtain the best characteristics of the SXR pulse generated as a result of Z-pinch implosion on the axis of the system. [ABSTRACT FROM AUTHOR]

Repetitive high-voltage square pulses are of great importance for producing long-pulse electron beams and high-power microwaves. One of possible technologies for the generation of such pulses is a Marx generator using pulse forming network (PFN) stages, often combined with a pulse sharpening technique to reduce the rise time to a few nanoseconds (peaking stage). This paper presents an innovative design, named the “zigzag design,” for the optimization of the compactness and of the rise time of 400-kV–85-ns PFN-Marx. Thanks to this design, the 16 stages of this generator, which delivers an open circuit output voltage of 720 kV, fit in a 650-mm length. For a slightly overmatched load ($Z_{\mathrm {load}} = 100 ~\Omega$), the output voltage reaches 400 kV with a rise time as less as 5 ns. The inductance reduction associated with the innovative zigzag design, which allows this sharp rise time with no need for a peaking stage, is described. The 85-ns plateau duration of the pulse is given by the PFN construction of each stage, which is based on six ceramic capacitors (2.1 nF–45 kV) connected within a strip line. The 16 PFN stages are housed in a 360-mm diameter gas pressurized vessel. Burst mode operation for a duration of 10 s at a pulse repetition frequency of 100 Hz is reported, for a resistive load and for the electron beam diode of a X-band relativistic backward-wave oscillator (BWO). To reach further compactness, the BWO system is integrated on side of the generator vessel and a U-shaped gas pressurized line connects both systems through a compact conical vacuum insulator. [ABSTRACT FROM AUTHOR]

This paper discusses the control of a modular multilevel converter (MMC) used as a grid interface for the klystron modulators in the compact linear collider (CLIC). The converter has a DC side load which takes short-duration power pulses, causing high DC side power fluctuations that are not tolerable if seen by the AC grid. The DC–AC power decoupling capability of the MMC enables mitigation of the power ripple on the AC side, guaranteeing compliance with power quality requirements. However, the pulse repetition rate of the CLIC modulators is synchronized the 50-Hz AC grid and this induces permanent power imbalance in the arms of the MMC, causing voltage deviation and overmodulation unless appropriate balancing strategies are implemented. Unlike existing arm balancing methods that control 50-Hz circulating currents to balance the arm powers, the method proposed in this paper introduces an augmented modulation strategy where modulation signals are redistributed among arms based on the demand from a balancing controller. The resulting controller has lower complexity and its simple structure enables an easier design of the balancing loop, which guarantees predictable dynamics in operation. The effectiveness of the method has been demonstrated in simulation for the full-scale CLIC converter ratings and experimentally on a 7-kW MMC prototype operating with a 3.3-kA pulsed DC load. [ABSTRACT FROM AUTHOR]

Surface modification of polytetrafluoroethylene (PTFE) is performed by nitrogen ion implantation for improving the PTFE surface flashover voltage in vacuum. In this paper, nitrogen ions are produced by an electron cyclotron resonance ion source. The properties of the samples are investigated with X-ray photoelectron spectroscopy, electrometer, microhardness tester, surface potential measurement, and surface flashover system. The Stopping and Range of Ions in Matter software is used to simulate the ion implantation. Experimental results show that the surface flashover voltage of treated samples improves remarkably and increases with the injection energy. After ion implantation, the content of fluorine in the treated samples decreases, and the content of oxygen increases. The surface conductivity increases from $1.15\times 10^{{-15}}$ to 1.36 10−13 S/m, the surface potential decreases faster, and the trap density and energy increase with the implantation energy. The process of electron avalanche and the accumulation of surface charges have been suppressed, thus hindering the development of flashover and improving the surface flashover voltage. [ABSTRACT FROM AUTHOR]

Causes of streamer acceleration caused by electron velocity saturation at intense electric fields are investigated in liquid dielectrics. Findings of this paper explain regimes of higher positive streamer velocity using a nonlinear electric-field-dependent electron velocity model that describes the streamer velocity more accurately when compared with the experimental results in the literature. Streamer branching in inhomogeneous transformer oil is also studied as an alternative cause of sudden changes in streamer velocity magnitude and direction, because after branching, the velocities of the born branches are significantly higher than the main streamer column velocity. In this paper, a 3-D model is established to incorporate nonsymmetrical variations in the streamer shape. The modeling results show that the streamer branching has both stochastic and deterministic origins. The stochastic parameters are determined by the content of inhomogeneity in the liquid and the deterministic origins of branching are defined by the structure of the volume charge layer at the streamer head. The results indicate that the sudden changes in streamer velocities are due to the electric-field-dependent electron mobility, electric-field-dependent ionization potential of dielectric molecules, and the branching capability of streamers even in extremely homogeneous liquid bulk. [ABSTRACT FROM PUBLISHER]